Abstract: Due to environmental concerns, the recent regulation on automobile fuel economy has been strengthened. The market demand for efficient vehicles is growing and automakers to improve engine fuel efficiency in the industry have been paying a lot of effort. To improve the fuel efficiency, it is necessary to reduce losses or to improve combustion efficiency of the engine. VVA (Variable Valve Actuation) technology enhances the engine's intake air flow, reduce pumping losses and mechanical friction losses. And also, VVA technology is the engine's low speed and high speed operation to implement each of appropriate valve lift. It improves the performance of engine in the entire operating range. This paper presents a design procedure of DC motor and drive for VVA system and shows the validity of the design result by experimental result with prototype.
Abstract: A SCADA (Supervisory Control And Data
Acquisition) system is an industrial control and monitoring system for
national infrastructures. The SCADA systems were used in a closed
environment without considering about security functionality in the
past. As communication technology develops, they try to connect the
SCADA systems to an open network. Therefore, the security of the
SCADA systems has been an issue. The study of key management for
SCADA system also has been performed. However, existing key
management schemes for SCADA system such as SKE(Key
establishment for SCADA systems) and SKMA(Key management
scheme for SCADA systems) cannot support broadcasting
communication. To solve this problem, an Advanced Key
Management Architecture for Secure SCADA Communication has
been proposed by Choi et al.. Choi et al.-s scheme also has a problem
that it requires lots of computational cost for multicasting
communication. In this paper, we propose an enhanced scheme which
improving computational cost for multicasting communication with
considering the number of keys to be stored in a low power
communication device (RTU).
Abstract: This study is concerned with pH solution detection
using 2 × 4 flexible sensor array based on a plastic polyethylene
terephthalate (PET) substrate that is coated a conductive layer and a
ruthenium dioxide (RuO2) sensitive membrane with the technologies
of screen-printing and RF sputtering. For data analysis, we also
prepared a dynamic measurement system for acquiring the response
voltage and analyzing the characteristics of the working electrodes
(WEs), such as sensitivity and linearity. In this condition, an array
measurement system was designed to acquire the original signal from
sensor array, and it is based on the method of digital signal processing
(DSP). The DSP modifies the unstable acquisition data to a direct
current (DC) output using the technique of digital filter. Hence, this
sensor array can obtain a satisfactory yield, 62.5%, through the design
measurement and analysis system in our laboratory.
Abstract: Machine tools are improved capacity remarkably during the 20th century. Improving the precision of machine tools are related with precision of products and accurate processing is always associated with the subject of interest. There are a lot of the elements that determine the precision of the machine, as guides, motors, structure, control, etc. In this paper we focused on the phenomenon that vertical movement system has worse precision than horizontal movement system even they were made up with same components. The vertical movement system needs to be studied differently from the horizontal movement system to develop its precision. The vertical movement system has load on its transfer direction and it makes the movement system weak in precision than the horizontal one. Some machines have mechanical counter balance, hydraulic or pneumatic counter balance to compensate the weight of the machine head. And there is several type of compensating the weight. It can push the machine head and also can use chain or wire lope to transfer the compensating force from counter balance to machine head. According to the type of compensating, there could be error from friction, pressure error of hydraulic or pressure control error. Also according to what to use for transferring the compensating force, transfer error of compensating force could be occur.
Abstract: Silver-exchanged zeolites and clays are used in
polymer composites to confer broad-spectrum antimicrobial
properties on a range of functional materials. Tobermorite is a layer
lattice mineral whose potential as a carrier for Ag+ ions in
antibacterial composites has not yet been investigated. Accordingly,
in this study, synthetic tobermorite was ion-exchanged with 10 wt%
silver ions and the resulting material was incorporated into a
composite film with chitosan. Chitosan is a biocompatible,
biodegradable derivative of chitin, a polysaccharide obtained from
the shells of crustaceans. The solvent-cast Ag+-exchanged
tobermorite-chitosan films were found to exhibit antimicrobial action
against Staphylococcus aureus, Escherichia coli and Pseudomonas
aeruginosa.
Abstract: The contribution deals with problem of take-off phase of back somersault with twisting with various numbers of twists along longitudinal body axis. The aim was to evaluate the changes in angles during transition phase from back handspring to back somersault using 3D kinematic analysis of the somersaults. We used Simi Motion System for the 3D kinematic analysis of the observed gymnastic element performed by Czech Republic female representative and 2008 Summer Olympic Games participant. The results showed that the higher the number of twists, the smaller the touchdown angle in which the gymnasts lands on the pad in the beginning of take-off phase. In back somersault with one twist (180°) the average angle is 54°, in 1080° back somersault the average angle is 45.9°. These results may help to improve technical training of sports gymnasts.
Abstract: The study aimed to investigate characteristics of
vegetative tissue for taxonomic purpose and possibly trend of waste
application in industry. Stems and branches of 15 species in Solanum
found in Thailand were prepared for fiber and examined by light
microscopy. Microstructural characteristic data of fiber i.e. fiber
length and width, fiber lumen diameter and fiber cell wall thickness
were recorded. The longest average fiber cell length (>3.9 mm.) were
obtained in S. lycopersicum L. and S. tuberosum L. Fiber cells from
S. lycopersicum also revealed the widest average diameter of whole
cell and its lumen at >45.5 μm and >29 μm respectively. However
fiber cells with thickest wall of > 9.6 μm were belonged to the
ornamental tree species, S. wrightii Benth. The results showed that
the slenderness ratio, Runkel ratio, and flexibility coefficient, with
potentially suitable for feedstock in paper industry fell in 4 exotic
species, i.e. Solanumamericanum L., S. lycopersicum, S.
seaforthianum Andr., and S. tuberosum L
Abstract: Naïve Bayes classifiers are simple probabilistic
classifiers. Classification extracts patterns by using data file with a set
of labeled training examples and is currently one of the most
significant areas in data mining. However, Naïve Bayes assumes the
independence among the features. Structural learning among the
features thus helps in the classification problem. In this study, the use
of structural learning in Bayesian Network is proposed to be applied
where there are relationships between the features when using the
Naïve Bayes. The improvement in the classification using structural
learning is shown if there exist relationship between the features or
when they are not independent.
Abstract: AAM has been successfully applied to face alignment,
but its performance is very sensitive to initial values. In case the initial
values are a little far distant from the global optimum values, there
exists a pretty good possibility that AAM-based face alignment may
converge to a local minimum. In this paper, we propose a progressive
AAM-based face alignment algorithm which first finds the feature
parameter vector fitting the inner facial feature points of the face and
later localize the feature points of the whole face using the first
information. The proposed progressive AAM-based face alignment
algorithm utilizes the fact that the feature points of the inner part of the
face are less variant and less affected by the background surrounding
the face than those of the outer part (like the chin contour). The
proposed algorithm consists of two stages: modeling and relation
derivation stage and fitting stage. Modeling and relation derivation
stage first needs to construct two AAM models: the inner face AAM
model and the whole face AAM model and then derive relation matrix
between the inner face AAM parameter vector and the whole face
AAM model parameter vector. In the fitting stage, the proposed
algorithm aligns face progressively through two phases. In the first
phase, the proposed algorithm will find the feature parameter vector
fitting the inner facial AAM model into a new input face image, and
then in the second phase it localizes the whole facial feature points of
the new input face image based on the whole face AAM model using
the initial parameter vector estimated from using the inner feature
parameter vector obtained in the first phase and the relation matrix
obtained in the first stage. Through experiments, it is verified that the
proposed progressive AAM-based face alignment algorithm is more
robust with respect to pose, illumination, and face background than the
conventional basic AAM-based face alignment algorithm.
Abstract: An approach for experimental measurement of the
dynamic characteristics of linear electromagnet actuators is
presented. It uses accelerometer sensor to register the armature
acceleration. The velocity and displacement of the moving parts can
be obtained by integration of the acceleration results. The armature
movement of permanent magnet linear actuator is acquired using this
technique. The results are analyzed and the performance of the
supposed approach is compared with the most commonly used
experimental setup where the displacement of the armature vs. time
is measured instead of its acceleration.
Abstract: The method of gait identification based on the nearest neighbor classification technique with motion similarity assessment by the dynamic time warping is proposed. The model based kinematic motion data, represented by the joints rotations coded by Euler angles and unit quaternions is used. The different pose distance functions in Euler angles and quaternion spaces are considered. To evaluate individual features of the subsequent joints movements during gait cycle, joint selection is carried out. To examine proposed approach database containing 353 gaits of 25 humans collected in motion capture laboratory is used. The obtained results are promising. The classifications, which takes into consideration all joints has accuracy over 91%. Only analysis of movements of hip joints allows to correctly identify gaits with almost 80% precision.
Abstract: Human heart valves diseased by congenital heart
defects, rheumatic fever, bacterial infection, cancer may cause stenosis
or insufficiency in the valves. Treatment may be with medication but
often involves valve repair or replacement (insertion of an artificial
heart valve). Bileaflet mechanical heart valves (BMHVs) are widely
implanted to replace the diseased heart valves, but still suffer from
complications such as hemolysis, platelet activation, tissue
overgrowth and device failure. These complications are closely related
to both flow characteristics through the valves and leaflet dynamics. In
this study, the physiological flow interacting with the moving leaflets
in a bileaflet mechanical heart valve (BMHV) is simulated with a
strongly coupled implicit fluid-structure interaction (FSI) method
which is newly organized based on the Arbitrary-Lagrangian-Eulerian
(ALE) approach and the dynamic mesh method (remeshing) of
FLUENT. The simulated results are in good agreement with previous
experimental studies. This study shows the applicability of the present
FSI model to the complicated physics interacting between fluid flow
and moving boundary.
Abstract: Recently in the field of bridges that are newly built or
repaired, fast construction is required more than ever. For these
reasons, precast prefabricated bridge that enables rapid construction is
actively discussed and studied today. In South Korea, it is called
modular bridge. Cross beam is an integral component of modular
bridge. It functions for load distribution, reduction of bending
moment, resistance of horizontal strength on lateral upper structure. In
this study, the structural characteristics of domestic and foreign cross
beam types were compared. Based on this, alternative cross beam
connection types suitable for modular bridge were selected. And
bulb-T girder specimens were fabricated with each type of connection.
The behavior of each specimen was analyzed under static loading, and
cross beam connection type which is expected to be best suited to
modular bridge proposed.
Abstract: The in vitro culture procedure of purple nutsedge
(Cyperus rotundus L.) for multiple shoot induction and tuber
formation was established. Multiple shoots were significantly
induced from a single shoot of about 0.5 – 0.8 cm long, on Murashige
and Skoog (MS) medium supplemented with 4.44 μM 6-
benzyladinine (BA) alone or in combination with 2.85 μM 1-
indoleacetic acid (IAA), providing 17.6 and 15.3 shoots per explant
with 31.2 and 27.5 leaves per explant, respectively, within 6 weeks of
culturing. Moreover, MS medium supplemented with 4.44 μM BA
and 2.85 μM IAA was suitable for tuber induction, obtaining 5.9
tubers with 3.4 rhizomes per explant. In combination with ancymidol
and higher concentration of sucrose, 11.1 μM BA and 60 g/L sucrose
or 11.1 μM BA, 7.8 μM ancymidol and 60 g/L sucrose induced 3.5
tubers with 1.6 rhizomes or 3.5 tubers without rhizome, respectively.
However, MS medium containing 3.9 or 7.8 μM ancymidol in
combination with either 60 or 80 g/L sucrose enchanced significant
root formation at 20.9 – 23.6 roots per explant.
Abstract: Single crystals of Magnesium alloys such as pure Mg,
Mg-1Zn-0.5Y, Mg-0.1Y, and Mg-0.1Ce alloys were successfully
fabricated in this study by employing the modified Bridgman method.
To determine the exact orientation of crystals, pole figure
measurement using X-ray diffraction were carried out on each single
crystal. Hardness and compression tests were conducted followed by
subsequent recrysatllization annealing. Recrystallization kinetics of
Mg alloy single crystals has been investigated. Fabricated single
crystals were cut into rectangular shaped specimen and solution
treated at 400oC for 24 hrs, and then deformed in compression mode
by 30% reduction. Annealing treatment for recrystallization has been
conducted on these cold-rolled plates at temperatures of 300oC for
various times from 1 to 20 mins. The microstructure observation and
hardness measurement conducted on the recrystallized specimens
revealed that static recrystallization of ternary alloy single crystal was
very slow, while recrystallization behavior of binary alloy single
crystals appeared to be very fast.
Abstract: This paper presents an automated inspection algorithm
for a thick plate. Thick plates typically have various types of surface
defects, such as scabs, scratches, and roller marks. These defects have
individual characteristics including brightness and shape. Therefore, it
is not simple to detect all the defects. In order to solve these problems
and to detect defects more effectively, we propose a dual light
switching lighting method and a defect detection algorithm based on
Gabor filters.
Abstract: The hard clam (meretrix lusoria) cultivated industry
has been developed vigorously for recent years in Taiwan, and
seawater quality determines the cultivated environment. The pH
concentration variation affects survival rate of meretrix lusoria
immediately. In order to monitor seawater quality, solid-state sensing
electrode of ruthenium-doped titanium dioxide (TiO2:Ru) is developed
to measure hydrogen ion concentration in different cultivated
solutions. Because the TiO2:Ru sensing electrode has high chemical
stability and superior sensing characteristics, thus it is applied as a pH
sensor. Response voltages of TiO2:Ru sensing electrode are readout by
instrument amplifier in different sample solutions. Mean sensitivity
and linearity of TiO2:Ru sensing electrode are 55.20 mV/pH and 0.999
from pH1 to pH13, respectively. We expect that the TiO2:Ru sensing
electrode can be applied to real environment measurement, therefore
we collect two sample solutions by different meretrix lusoria
cultivated ponds in the Yunlin, Taiwan. The two sample solutions are
both measured for 200 seconds after calibration of standard pH buffer
solutions (pH7, pH8 and pH 9). Mean response voltages of sample 1
and sample 2 are -178.758 mV (Standard deviation=0.427 mV) and
-180.206 mV (Standard deviation =0.399 mV), respectively. Response
voltages of the two sample solutions are between pH 8 and pH 9 which
conform to weak alkali range and suitable meretrix lusoria growth. For
long-term monitoring, drift of cultivated solutions (sample 1 and
sample 2) are 1.16 mV/hour and 1.03 mV/hour, respectively.
Abstract: The alternative technique for sterilization of culture
medium to replace autoclaving was carried out. For sterilization of
culture medium without autoclaving, some commercial pure essential
oils, bergamot oil, betel oil, cinnamon oil, lavender oil and turmeric
oil, were tested alone or in combinations with some disinfectants,
10% povidone-iodine and 2% iodine + 2.4% potassium iodide. Each
essential oil or combination was added to 25-mL Murashige and
Skoog (MS) medium before medium was solidified in a 120-mL
container, kept for 2 weeks before evaluating sterile conditions.
Treated media, supplemented with essential oils, were compared to
control medium, autoclaved at 121 degree Celsius for 15 min. In
vitro sterile conditions were found 20 – 100% from these treated
media compared to 100% sterile condition from autoclaved medium.
Treated media obtained 100% sterile conditions were chosen for
culturing chrysanthemum shoots. It was found that 10% povidoneiodine
in combination with cinnamon oil (3:1) and 2% iodine + 2.4%
potassium iodide in combination with lavender oil (1:3) at the
concentration of 36 3L/25 mL medium provided the promising
growth of shoot explants.
Abstract: The aim of this paper is to confirm the effect of key
design parameters, the punch radius and punch angle, on rupture of the
expansion tube using a finite element analysis with a ductile damage
model. The results of the finite element analysis indicated that the
expansion ratio of the tube was mainly affected by the radius of the
punch. However, the rupture was more affected by the punch angle
than the radius of the punch. The existence of a specific punch angle,
at which rupture did not occur, even if the radius of the punch was
increased, was found.
Abstract: Two species of Physalis, P.angulataL. and P.
peruviana L. were used as models for comparative study to
understand the values of micro-morphological, -anatomical and
architectural characteristics of leaf for taxonomic purposes and
possibly breeding and commercial applications. Both speciespossess
amphistomaticleaves with 1-layer epidermis, 3-4-layer spongy
mesophyll andbicollateral bundle midrib. Palisade parenchyma cells
of P. angulatawere almost twice longer (65-75 μm) than the other
one. Type of stomata was similar as anomocyticbut stomatal
index(SI) at adaxial surface and abaxial surface of P. angulata were
less than of P. peruvianaas 3.57, 4.00 and6.25, 6.66 respectively.
Some leaf architectural characteristics such as leaf shape, order of
venationalsoprovided information of taxonomic significance