Abstract: Early diagnosis of infection like Hep-B virus in blood
is important for low cost medical treatment. For this purpose, it is
desirable to develop a point of care device which should be able to
detect trace quantities of the target molecule in blood. In this paper,
we report a nanoporous silicon oxide sensor which is capable of
detecting down to 1fM concentration of Hep-B surface antigen in
blood without the requirement of any centrifuge or pre-concentration.
This has been made possible by the presence of resonant peak in the
sensitivity characteristics. This peak is observed to be dependent only
on the concentration of the specific antigen and not on the interfering
species in blood serum. The occurrence of opposite impedance
change within the pores and at the bottom of the pore is responsible
for this effect. An electronic interface has also been designed to
provide a display of the virus concentration.
Abstract: Taiwan is a hyper endemic area for the Hepatitis B
virus (HBV). The estimated total number of HBsAg carriers in the
general population who are more than 20 years old is more than 3
million. Therefore, a case record review is conducted from January
2003 to June 2007 for all patients with a diagnosis of acute hepatitis
who were admitted to the Emergency Department (ED) of a
well-known teaching hospital. The cost for the use of medical
resources is defined as the total medical fee. In this study, principal
component analysis (PCA) is firstly employed to reduce the number of
dimensions. Support vector regression (SVR) and artificial neural
network (ANN) are then used to develop the forecasting model. A total
of 117 patients meet the inclusion criteria. 61% patients involved in
this study are hepatitis B related. The computational result shows that
the proposed PCA-SVR model has superior performance than other
compared algorithms. In conclusion, the Child-Pugh score and
echogram can both be used to predict the cost of medical resources for
patients with acute hepatitis in the ED.
Abstract: This study examined how individuals in their
respective teams contributed to innovation performance besides
defining the term of innovation in their own respective views. This
study also identified factors that motivated University staff to
contribute to the innovation products. In addition, it examined
whether there is a significant relationship between professional
training level and the length of service among university staff
towards innovation and to what extent do the two variables
contributed towards innovative products. The significance of this
study is that it revealed the strengths and weaknesses of the
university staff when contributing to innovation performance.
Stratified-random sampling was employed to determine the samples
representing the population of lecturers in the study, involving 123
lecturers in one of the local universities in Malaysia. The method
employed to analyze the data is through categorizing into themes for
the open-ended questions besides using descriptive and inferential
statistics for the quantitative data. This study revealed that two types
of definition for the term “innovation” exist among the university
staff, namely, creation of new product or new approach to do things
as well as value-added creative way to upgrade or improve existing
process and service to be more efficient. This study found that the
most prominent factor that propels them towards innovation is to
improve the product in order to benefit users, followed by selfsatisfaction
and recognition. This implies that the staff in the
organization viewed the creation of innovative products as a process
of growth to fulfill the needs of others and also to realize their
personal potential. This study also found that there was only a
significant relationship between the professional training level and
the length of service of 4 - 6 years among the university staff. The
rest of the groups based on the length of service showed that there
was no significant relationship with the professional training level
towards innovation. Moreover, results of the study on directional
measures depicted that the relationship for the length of service of 4-
6 years with professional training level among the university staff is
quite weak. This implies that good organization management lies on
the shoulders of the key leaders who enlighten the path to be
followed by the staff.
Abstract: The performance of box-type solar cookers has been
reported by several researchers but little attention was paid to the
effect of the type of insulation material on the energy and exergy
efficiency of these cookers. This research aimed at evaluating the
energy and exergy efficiencies of the box-type cookers containing
different insulation materials. Energy and exergy efficiencies of five
box-type solar cookers insulated with maize cob, air (control), maize
husk, coconut coir and polyurethane foam respectively were obtained
over a period of three years. The cookers were evaluated using water
heating test procedures in determining the energy and exergy
analysis. The results were subjected to statistical analysis using
ANOVA. The result shows that the average energy input for the five
solar cookers were: 245.5, 252.2, 248.7, 241.5 and 245.5J
respectively while their respective average energy losses were: 201.2,
212.7, 208.4, 189.1 and 199.8J. The average exergy input for five
cookers were: 228.2, 234.4, 231.1, 224.4 and 228.2J respectively
while their respective average exergy losses were: 223.4, 230.6,
226.9, 218.9 and 223.0J. The energy and exergy efficiency was
highest in the cooker with coconut coir (37.35 and 3.90%
respectively) in the first year but was lowest for air (11 and 1.07%
respectively) in the third year. Statistical analysis showed significant
difference between the energy and exergy efficiencies over the years.
These results reiterate the importance of a good insulating material
for a box-type solar cooker.
Abstract: Fixed-geometry hydrodynamic journal bearings are
one of the best supporting systems for several applications of rotating
machinery. Cylindrical journal bearings present excellent loadcarrying
capacity and low manufacturing costs, but they are subjected
to the oil-film instability at high speeds. An attempt of overcoming
this instability problem has been the development of non-circular
journal bearings. This work deals with an analysis of oil-lubricated
elliptical journal bearings using the finite element method. Steadystate
and dynamic performance characteristics of elliptical bearings
are rendered by zeroth- and first-order lubrication equations obtained
through a linearized perturbation method applied on the classical
Reynolds equation. Four-node isoparametric rectangular finite
elements are employed to model the bearing thin film flow. Curves of
elliptical bearing load capacity and dynamic force coefficients are
rendered at several operating conditions. The results presented in this
work demonstrate the influence of the bearing ellipticity on its
performance at different loading conditions.
Abstract: A three-dimensional numerical model of
thermoelectric generator (TEG) modules attached to a large chimney
plate is proposed and solved numerically using a control volume based
finite difference formulation. The TEG module consists of a
thermoelectric generator, an elliptical pin-fin heat sink, and a cold
plate for water cooling. In the chimney, the temperature of flue gases is
450-650K. Although the TEG hot-side temperature and thus the
electric power output can be increased by inserting an elliptical pin-fin
heat sink into the chimney tunnel to increase the heat transfer area, the
pin fin heat sink would cause extra pumping power at the same time.
The main purpose of this study is to analyze the effects of geometrical
parameters on the electric power output and chimney pressure drop
characteristics. The effects of different operating conditions, including
various inlet velocities (Vin= 1, 3, 5 m/s), inlet temperatures (Tgas = 450,
550, 650K) and different fin height (0 to 150 mm) are discussed in
detail. The predicted numerical data for the power vs. current (P-I)
curve are in good agreement (within 11%) with the experimental data.
Abstract: International and domestic environmental law has
evolved quite rapidly in the last few decades. At the international
level the Stockholm and Rio Declarations paved the way for a broad
based consensus of the international community on environmental
issues and principles. At the Domestic level also many states have
incorporated environmental protection in their constitutions and even
more states are doing the same at least in their domestic legislations.
In this process of evolution environmental law has unleashed a
number of novel principles such as; the participatory principle, the
polluter pays principle, the precautionary principle, the intergenerational
and intra-generational principles, the prevention
principle, the sustainable development principle and so on.
Abstract: Flash Floods, together with landslides, are a common
natural threat for people living in mountainous regions and foothills.
One way to deal with this constant menace is the use of Early
Warning Systems, which have become a very important mitigation
strategy for natural disasters.
In this work we present our proposal for a pilot Flash Flood Early
Warning System for Santiago, Chile, the first stage of a more
ambitious project that in a future stage shall also include early
warning of landslides.
To give a context for our approach, we first analyze three existing
Flash Flood Early Warning Systems, focusing on their general
architectures. We then present our proposed system, with main focus
on the decision support system, a system that integrates empirical
models and fuzzy expert systems to achieve reliable risk estimations.
Abstract: This paper examines the effect of the volatility of oil
prices on food price in South Africa using monthly data covering the
period 2002:01 to 2014:09. Food price is measured by the South
African consumer price index for food while oil price is proxied by
the Brent crude oil. The study employs the GARCH-in-mean VAR
model, which allows the investigation of the effect of a negative and
positive shock in oil price volatility on food price. The model also
allows the oil price uncertainty to be measured as the conditional
standard deviation of a one-step-ahead forecast error of the change in
oil price. The results show that oil price uncertainty has a positive
and significant effect on food price in South Africa. The responses of
food price to a positive and negative oil price shocks is asymmetric.
Abstract: In recent years parasitic antenna play major role in
MIMO systems because of their gain and spectral efficiency. In this
paper, single RF chain MIMO transmitter is designed using
reconfigurable parasitic antenna. The Spatial Modulation (SM) is a
recently proposed scheme in MIMO scenario which activates only
one antenna at a time. The SM entirely avoids ICI and IAS, and only
requires a single RF chain at the transmitter. This would switch ON a
single transmit-antenna for data transmission while all the other
antennas are kept silent. The purpose of the parasitic elements is to
change the radiation pattern of the radio waves which is emitted from
the driven element and directing them in one direction and hence
introduces transmit diversity. Diode is connect between the patch and
ground by changing its state (ON and OFF) the parasitic element act
as reflector and director and also capable of steering azimuth and
elevation angle. This can be achieved by changing the input
impedance of each parasitic element through single RF chain. The
switching of diode would select the single parasitic antenna for
spatial modulation. This antenna is expected to achieve maximum
gain with desired efficiency.
Abstract: Nature is the immense gifted source for solving
complex problems. It always helps to find the optimal solution to
solve the problem. Mobile Ad Hoc NETwork (MANET) is a wide
research area of networks which has set of independent nodes. The
characteristics involved in MANET’s are Dynamic, does not depend
on any fixed infrastructure or centralized networks, High mobility.
The Bio-Inspired algorithms are mimics the nature for solving
optimization problems opening a new era in MANET. The typical
Swarm Intelligence (SI) algorithms are Ant Colony Optimization
(ACO), Artificial Bee Colony (ABC), Particle Swarm Optimization
(PSO), Modified Termite Algorithm, Bat Algorithm (BA), Wolf
Search Algorithm (WSA) and so on. This work mainly concentrated
on nature of MANET and behavior of nodes. Also it analyses various
performance metrics such as throughput, QoS and End-to-End delay
etc.
Abstract: Morphological interaction of porcine cumulus-oocyte
complexes (pCOCs) was investigated on in vitro condition using
electron microscope (SEM and TEM). The totals of 1,923 oocytes
were round in shape, surrounded by Zona pellucida with layer of
cumulus cells ranging between 59.29-202.14 μm in size. They were
classified into intact-, multi-, partial cumulus cell layer oocyte, and
completely denuded oocyte, at the percentage composition of 22.80%
32.70%, 18.60%, and 25.90 % respectively. The pCOCs classified as
intact- and multi cumulus cell layer oocytes were further culturing at
37°C with 5% CO2, 95% air atmosphere and high humidity for 44 h
in M199 with Earle’s salts supplemented with 10% HTFCS, 2.2
mg/mL NaHCO3, 1 M Hepes, 0.25 mM pyruvate, 15 μg/mL porcine
follicle-stimulating hormone, 1 μg/mL LH, 1μg/mL estradiol with
ethanol, and 50 μg/mL gentamycin sulfate. On electron microscope
study, cumulus cells were found to stick their processes to secrete
substance from the sac-shape end into Zona pellucida of the oocyte
and also communicated with the neighboring cells through their
microvilli on the beginning of incubation period. It is believed that
the cumulus cells communicate with the oocyte by inserting the
microvilli through this gap and embedded in the oocyte cytoplasm
before secreting substance, through the sac-shape end of the
microvilli, to inhibit primary oocyte development at the prophase I.
Morphological changes of the complexes were observed after
culturing for 24-44 h. One hundred percentages of the cumulus layers
were expanded and cumulus cells were peeling off from the oocyte
surface. In addition, the round-shape cumulus cells transformed
themselves into either an elongate shape or a columnar shape, and no
communication between cumulus neighboring cells. After 44 h of
incubation time, diameter of oocytes surrounded by cumulus cells
was larger than 0 h incubation. The effect of hormones in culture
medium is exerted by their receptors present in porcine oocyte. It is
likely that all morphological changes of the complexes after hormone
treatment were to allow maturation of the oocyte. This study
demonstrated that the association of hormones in M199 could
promote porcine follicle activation in 44 h in vitro condition. This
culture system should be useful for studying the regulation of early
follicular growth and development, especially because these follicles represent a large source of oocytes that could be used in vitro for cell
technology.
Abstract: Robotics brings together several very different
engineering areas and skills. There are various types of robot such as
humanoid robot, mobile robots, remotely operated vehicles, modern
autonomous robots etc. This survey paper advocates the operation of a
robotic car (remotely operated vehicle) that is controlled by a mobile
phone (communicate on a large scale over a large distance even from
different cities). The person makes a call to the mobile phone placed
in the car. In the case of a call, if any one of the button is pressed, a
tone equivalent to the button pressed is heard at the other end of the
call. This tone is known as DTMF (Dual Tone Multiple Frequency).
The car recognizes this DTMF tone with the help of the phone stacked
in the car. The received tone is processed by the Arduino
microcontroller. The microcontroller is programmed to acquire a
decision for any given input and outputs its decision to motor drivers
in order to drive the motors in the forward direction or backward
direction or left or right direction. The mobile phone that makes a call
to cell phone stacked in the car act as a remote.
Abstract: Paraffinic oils were submitted to microbial action. The
microorganisms consisted of bacteria of the genera Pseudomonas sp.
and Bacillus lincheniforms. The alterations in interfacial tension were
determined using a tensometer and applying the hanging drop
technique at room temperature (299 K ±275 K). The alteration in the
constitution of the paraffins was evaluated by means of gas
chromatography. The microbial activity was observed to reduce
interfacial tension by 54 to 78%, as well as consuming the paraffins
C19 to C29 and producing paraffins C36 to C44. The LIFirr technique
made it possible to determine the microbial action quickly.
Abstract: The thermal control in many systems is widely
accomplished applying mixed convection process due to its low cost,
reliability and easy maintenance. Typical applications include the
aircraft electronic equipment, rotating-disc heat exchangers, turbo
machinery, and nuclear reactors, etc. Natural convection in an inclined
square enclosure heated via wall heater has been studied numerically.
Finite volume method is used for solving momentum and energy
equations in the form of stream function–vorticity. The right and left
walls are kept at a constant temperature, while the other parts are
adiabatic. The range of the inclination angle covers a whole revolution.
The method is validated for a vertical cavity. A general power law
dependence of the Nusselt number with respect to the Rayleigh
number with the coefficient and exponent as functions of the
inclination angle is presented. For a fixed Rayleigh number, the
inclination angle increases or decreases is found.
Abstract: Catalytic combustion of methane is imperative due to
stability of methane at low temperature. Methane (CH4), therefore,
remains unconverted in vehicle exhausts thereby causing greenhouse
gas GHG emission problem. In this study, heterogeneous catalysts of
palladium with bio-char (2 wt% Pd/Bc) and Al2O3 (2wt% Pd/ Al2O3)
supports were prepared by incipient wetness impregnation and then
subsequently tested for catalytic combustion of CH4. Support-porous
heterogeneous catalytic combustion (HCC) material were selected
based on factors such as surface area, porosity, thermal stability,
thermal conductivity, reactivity with reactants or products, chemical
stability, catalytic activity, and catalyst life. Sustainable and
renewable support-material of bio-mass char derived from palm shell
waste material was compared with those from the conventional
support-porous materials. Kinetic rate of reaction was determined for
combustion of methane on Palladium (Pd) based catalyst with Al2O3
support and bio-char (Bc). Material characterization was done using
TGA, SEM, and BET surface area. The performance test was
accomplished using tubular quartz reactor with gas mixture ratio of
3% methane and 97% air. The methane porous-HCC conversion was
carried out using online gas analyzer connected to the reactor that
performed porous-HCC. BET surface area for prepared 2 wt% Pd/Bc
is smaller than prepared 2wt% Pd/ Al2O3 due to its low porosity
between particles. The order of catalyst activity based on kinetic rate
on reaction of catalysts in low temperature was 2wt%
Pd/Bc>calcined 2wt% Pd/ Al2O3> 2wt% Pd/ Al2O3>calcined 2wt%
Pd/Bc. Hence agro waste material can successfully be utilized as an
inexpensive catalyst support material for enhanced CH4 catalytic
combustion.
Abstract: The Al-MoO3-P-CdTe-Al MOS sandwich structures
were fabricated by vacuum deposition method on cleaned glass
substrates. Capacitance versus voltage measurements were performed
at different frequencies and sweep rates of applied voltages for oxide
and semiconductor films of different thicknesses. In the negative
voltage region of the C-V curve a high differential capacitance of the
semiconductor was observed and at high frequencies (
Abstract: Cemented carbide balls are usually implemented in
industry under the environment of high speed, high temperature,
corrosiveness and strong collisions. However, its application is limited
due to high fabrication cost, processing efficiency and quality. A novel
eccentric lapping method with two rotatable lapping plates was
proposed in this paper. A mathematical model was constructed to
analyze the influence of each design parameter on this lapping method.
To validate this new lapping method, an orthogonal experiment was
conducted with cemented carbide balls (YG6). The simulation model
was verified and the optimal lapping parameters were derived. The
results show that the surface roundness of the balls reaches to 0.65um
from 2um in 1 hour using this lapping method. So, using this novel
lapping method, it can effectively improve the machining precision
and efficiency of cemented carbide balls.
Abstract: Over the past four decades, the fatigue behavior of
nickel-based alloys has been widely studied. However, in recent
years, significant advances in the fabrication process leading to grain
size reduction have been made in order to improve fatigue properties
of aircraft turbine discs. Indeed, a change in particle size affects the
initiation mode of fatigue cracks as well as the fatigue life of the
material. The present study aims to investigate the fatigue behavior of
a newly developed nickel-based superalloy under biaxial-planar
loading. Low Cycle Fatigue (LCF) tests are performed at different
stress ratios so as to study the influence of the multiaxial stress state
on the fatigue life of the material. Full-field displacement and strain
measurements as well as crack initiation detection are obtained using
Digital Image Correlation (DIC) techniques. The aim of this
presentation is first to provide an in-depth description of both the
experimental set-up and protocol: the multiaxial testing machine, the
specific design of the cruciform specimen and performances of the
DIC code are introduced. Second, results for sixteen specimens
related to different load ratios are presented. Crack detection, strain
amplitude and number of cycles to crack initiation vs. triaxial stress
ratio for each loading case are given. Third, from fractographic
investigations by scanning electron microscopy it is found that the
mechanism of fatigue crack initiation does not depend on the triaxial
stress ratio and that most fatigue cracks initiate from subsurface
carbides.
Abstract: This paper addresses the issue of the autonomous
mobile robot (AMR) navigation task based on the hybrid control
modes. The novel hybrid control mode, based on multi-sensors
information by using the fuzzy approach, has been presented in this
research. The system operates in real time, is robust, enables the robot
to operate with imprecise knowledge, and takes into account the
physical limitations of the environment in which the robot moves,
obtaining satisfactory responses for a large number of different
situations. An experiment is simulated and carried out with a pioneer
mobile robot. From the experimental results, the effectiveness and
usefulness of the proposed AMR obstacle avoidance and navigation
scheme are confirmed. The experimental results show the feasibility,
and the control system has improved the navigation accuracy. The
implementation of the controller is robust, has a low execution time,
and allows an easy design and tuning of the fuzzy knowledge base.