Abstract: The objective of this study was to evaluate the
physical and chemical characteristics of Serra da Estrela cheese and
compare these results with those of the sensory analysis. For the
study were taken six samples of Serra da Estrela cheese produced
with 6 different ecotypes of thistle in a dairy situated in Penalva do
Castelo. The chemical properties evaluated were moisture content,
protein, fat, ash, chloride and pH; the physical properties studied
were color and texture; and finally a sensory evaluation was
undertaken. The results showed moisture varying in the range 40-
48%, protein in the range 15-20%, fat between 41-45%, ash between
3.9-5.0% and chlorides varying from 1.2 to 3.0%. The pH varied
from 4.8 to 5.4. The textural properties revealed that the crust
hardness is relatively low (maximum 7.3 N), although greater than
flesh firmness (maximum 1.7 N), and also that these cheeses are in
fact soft paste type, with measurable stickiness and intense
adhesiveness. The color analysis showed that the crust is relatively
light (L* over 50), and with a predominant yellow coloration (b*
around 20 or over) although with a slight greenish tone (a* negative).
The results of the sensory analysis did not show great variability for
most of the attributes measured, although some differences were
found in attributes such as crust thickness, crust uniformity, and
creamy flesh.
Abstract: Flours of wheat, chestnut, acorn and lupin were
evaluated in relation to phenolic compounds, antioxidant activity, and
oxalate content. At the chemical level the results show some
variability between samples by type of flour, and the sample of
chestnut flour presented the higher value of oxalate (0.00348
mg/100g) when compared to the other samples in the study.
Considering the content of phenolic compounds, the sample that
stood out was the acorn flour, having a high value of 0.812 g
AGE/100 g. All the samples presented intermediate content of
antioxidant activity and the sample that showed a slightly higher
value was the wheat flour with a value of 0.746 mM TRE/g sample.
Abstract: A new concept of response system is proposed for
filling the gap that exists in reducing vulnerability during immediate
response to natural disasters. Real Time Early Response Systems
(RTERSs) incorporate real time information as feedback data for
closing control loop and for generating real time situation assessment.
A review of the state of the art on works that fit the concept of
RTERS is presented, and it is found that they are mainly focused on
manmade disasters. At the same time, in response phase of natural
disaster management many works are involved in creating early
warning systems, but just few efforts have been put on deciding what
to do once an alarm is activated. In this context a RTERS arises as a
useful tool for supporting people in their decision making process
during natural disasters after an event is detected, and also as an
innovative context for applying well-known automation technologies
and automatic control concepts and tools.
Abstract: For a bluff body, dimples behave like roughness
elements in stimulating a turbulent boundary layer, leading to delayed
flow separation, a smaller wake and lower form drag. This is very
different in principle from the application of dimples to streamlined
body, where any reduction in drag would be predominantly due to a
reduction in skin friction. In the present work, a car model with
different dimple geometry is simulated using k-ε turbulence modeling
to determine its effect to the aerodynamics performance. Overall, the
results show that the application of dimples manages to reduce the
drag coefficient of the car model.
Abstract: This work introduces a simple device designed to
perform in-situ direct shear and sinkage tests on granular materials
as sand, clays, or regolith. It consists of a box nested within a larger
box. Both have open bottoms, allowing them to be lowered into the
material. Afterwards, two rotating plates on opposite sides of the
outer box will rotate outwards in order to clear regolith on either
side, providing room for the inner box to move relative to the plates
and perform a shear test without the resistance of the surrounding
soil. From this test, Coulomb parameters, including cohesion and
internal friction angle, as well as, Bekker parameters can be inferred.
This device has been designed for a laboratory setting, but with few
modifications, could be put on the underside of a rover for use in
a remote location. The goal behind this work is to ultimately create
a compact, but accurate measuring tool to put onto a rover or any
kind of exploratory vehicle to test for regolith properties of celestial
bodies.
Abstract: Concrete is found to undergo degradation when
subjected to elevated temperatures and loose substantial amount of its
strength. The loss of strength in concrete is mainly attributed to
decomposition of C-S-H and release of physically and chemically
bound water, which begins when the exposure temperature exceeds
100°C. When such a concrete comes in contact with moisture, the
cement paste is found rehydrate and considerable amount of strength
lost is found to recover. This paper presents results of an
experimental program carried out to investigate the effect of recuring
on strength gain of OPC concrete specimens subjected to elevated
temperatures from 200°C to 800°C, which were subjected to
retention time of two hours and four hours at the designated
temperature. Strength recoveries for concrete subjected to 7
designated elevated temperatures are compared. It is found that the
efficacy of recuring as a measure of strength recovery reduces with
increase in exposure temperature.
Abstract: The ultrasound imaging is very popular to diagnosis
the disease because of its non-invasive nature. The ultrasound
imaging slowly produces low quality images due to the presence of
spackle noise and wave interferences. There are several algorithms to
be proposed for the segmentation of ultrasound carotid artery images
but it requires a certain limit of user interaction. The pixel in an
image is highly correlated so the spatial information of surrounding
pixels may be considered in the process of image segmentation which
improves the results further. When data is highly correlated, one pixel
may belong to more than one cluster with different degree of
membership. There is an important step to computerize the evaluation
of arterial disease severity using segmentation of carotid artery lumen
in 2D and 3D ultrasonography and in finding vulnerable
atherosclerotic plaques susceptible to rupture which can cause stroke.
Abstract: The goal of image segmentation is to cluster pixels
into salient image regions. Segmentation could be used for object
recognition, occlusion boundary estimation within motion or stereo
systems, image compression, image editing, or image database lookup.
In this paper, we present a color image segmentation using
support vector machine (SVM) pixel classification. Firstly, the pixel
level color and texture features of the image are extracted and they
are used as input to the SVM classifier. These features are extracted
using the homogeneity model and Gabor Filter. With the extracted
pixel level features, the SVM Classifier is trained by using FCM
(Fuzzy C-Means).The image segmentation takes the advantage of
both the pixel level information of the image and also the ability of
the SVM Classifier. The Experiments show that the proposed method
has a very good segmentation result and a better efficiency, increases
the quality of the image segmentation compared with the other
segmentation methods proposed in the literature.
Abstract: Although there had been a many studies that shows
the impact of air pollution on physical health, comparatively less was
known of human behavioral responses and annoyance impacts.
Annoyance caused by air pollution is a public health problem because
it can be an ambient stressor causing stress and disease and can affect
quality of life. The objective of this work is to evaluate the
annoyance caused by air pollution in two different industrialized
urban areas, Dunkirk (France) and Vitoria (Brazil). The populations
of these cities often report feeling annoyed by dust. Surveys were
conducted, and the collected data were analyzed using statistical
analyses. The results show that sociodemographic variables,
importance of air quality, perceived industrial risk, perceived air
pollution and occurrence of health problems play important roles in
the perceived annoyance. These results show the existence of a
common problem in geographically distant areas and allow
stakeholders to develop prevention strategies.
Abstract: Cement concrete is a complex mixture of different
materials. Behaviour of concrete depends on its mix proportions and
constituents when it is subjected to elevated temperatures. Principal
effects due to elevated temperatures are loss in compressive strength,
loss in weight or mass, change in colour and spall of concrete. The
experimental results of normal concrete and high strength concrete
subjected elevated temperatures at 200°C, 400°C, 600°C, and 800°C
and different cooling regimes viz. air cooling, water quenching on
different grade of concrete are reported in this paper.
Abstract: The Blue Nile Basin is the most important tributary of
the Nile River. Egypt and Sudan are almost dependent on water
originated from the Blue Nile. This multi-dependency creates
conflicts among the three countries Egypt, Sudan, and Ethiopia
making the management of these conflicts as an international issue.
Good assessment of the water resources of the Blue Nile is an
important to help in managing such conflicts. Hydrological models
are good tool for such assessment. This paper presents a critical
review of the nature and variability of the climate and hydrology of
the Blue Nile Basin as a first step of using hydrological modeling to
assess the water resources of the Blue Nile. Many several attempts
are done to develop basin-scale hydrological modeling on the Blue
Nile. Lumped and semi distributed models used averages of
meteorological inputs and watershed characteristics in hydrological
simulation, to analyze runoff for flood control and water resource
management. Distributed models include the temporal and spatial
variability of catchment conditions and meteorological inputs to
allow better representation of the hydrological process. The main
challenge of all used models was to assess the water resources of the
basin is the shortage of the data needed for models calibration and
validation. It is recommended to use distributed model for their
higher accuracy to cope with the great variability and complexity of
the Blue Nile basin and to collect sufficient data to have more
sophisticated and accurate hydrological modeling.
Abstract: This article discusses issues related to the System of
Innovation: Comparing economies of Brazil and South Africa.
Having as this study aimed at comparing the Innovation System of
the countries mentioned. Then briefly describe the process of Venture
Capital and present the industry innovation in Brazil and South
Africa. The methodological approach described in this article is
descriptive and the approach is qualitative, taking as a basis
secondary data relating to research articles. The main results are
related to the different forms of financing of Venture Capital used by
countries compared, in addition to the training and economic policy.
And finally, it was highlighted the importance of implementation of
policy reforms for the Brazil and Africa in the innovation process.
Abstract: Our goal is development of an algorithm capable of
predicting the directional trend of the Standard and Poor’s 500 index
(S&P 500). Extensive research has been published attempting to
predict different financial markets using historical data testing on an
in-sample and trend basis, with many authors employing excessively
complex mathematical techniques. In reviewing and evaluating these
in-sample methodologies, it became evident that this approach was
unable to achieve sufficiently reliable prediction performance for
commercial exploitation. For these reasons, we moved to an out-ofsample
strategy based on linear regression analysis of an extensive
set of financial data correlated with historical closing prices of the
S&P 500. We are pleased to report a directional trend accuracy of
greater than 55% for tomorrow (t+1) in predicting the S&P 500.
Abstract: The management of Helicobacter pylori (H. pylori)
eradication is still a matter of discussion, full effectiveness is rarely
achieved, and it has many adverse effects. The use of probiotics may
be associated with better eradication rates and possibly prevention of
adverse events due to antibiotic therapy. The present clinical study
was undertaken to evaluate the efficacy of a specially designed
fermented milk product, containing Bifidobacterium lactis B420, on
the eradication of H. pylori infection in a prospective, randomized,
double-blind, controlled study in humans. Four test fermented milks
(FM) were specially designed in which counts of viable cells in all
products were 10^10 Log CFU. 100 mL-1 for Bifidobacterium lactis -
Bifidobacterium species 420. 190 subjects infected with H. pylori,
with previous diagnosis of functional dyspepsia according to Rome
III criteria entered the study. Bifidobacterium lactis B420,
administered twice a day for 90 days was not able to eradicate H.
pylori in Brazilian patients with functional dyspepsia.
Abstract: Nature is a great source of inspiration for solving
complex problems in networks. It helps to find the optimal solution.
Metaheuristic algorithm is one of the nature-inspired algorithm which
helps in solving routing problem in networks. The dynamic features,
changing of topology frequently and limited bandwidth make the
routing, challenging in MANET. Implementation of appropriate
routing algorithms leads to the efficient transmission of data in
mobile ad hoc networks. The algorithms that are inspired by the
principles of naturally-distributed/collective behavior of social
colonies have shown excellence in dealing with complex
optimization problems. Thus some of the bio-inspired metaheuristic
algorithms help to increase the efficiency of routing in ad hoc
networks. This survey work presents the overview of bio-inspired
metaheuristic algorithms which support the efficiency of routing in
mobile ad hoc networks.
Abstract: The characteristic requirement for producing
rectangular shape bottles was a uniform thickness of the plastic bottle
wall. Die shaping was a good technique which controlled the wall
thickness of bottles. An advance technology which was the finite
element method (FEM) for blowing parison to be a rectangular shape
bottle was conducted to reduce waste plastic from a trial and error
method of a die shaping and parison control method. The artificial
intelligent (AI) comprised of artificial neural network and genetic
algorithm was selected to optimize the die gap shape from the FEM
results. The application of AI technique could optimize the suitable
die gap shape for the parison blow molding which did not depend on
the parison control method to produce rectangular bottles with the
uniform wall. Particularly, this application can be used with cheap
blow molding machines without a parison controller therefore it will
reduce cost of production in the bottle blow molding process.
Abstract: Many aluminum motorcycle parts produced by a high
pressure die casting. Some parts such as fuel caps were a thin and
complex shape. This part risked for porosities and blisters on surface
if it only depended on an experience of mold makers for mold design.
This research attempted to use CAST-DESIGNER software
simulated the high pressure die casting process with the same process
parameters of a motorcycle fuel cap production. The simulated results
were compared with fuel cap products and expressed the same
porosity and blister locations on cap surface. An average of absolute
difference of simulated results was obtained 0.094 mm when
compared the simulated porosity and blister defect sizes on the fuel
cap surfaces with the experimental micro photography. This
comparison confirmed an accuracy of software and will use the
setting parameters to improve fuel cap molds in the further work.
Abstract: The wear measuring and wear modelling are
fundamental issues in the industrial field, mainly correlated to the
economy and safety. Therefore, there is a need to study the wear
measurements and wear estimation. Pin-on-disc test is the most
common test which is used to study the wear behaviour. In this paper,
the pin-on-disc (AEROTECH UNIDEX 11) is used for the
investigation of the effects of normal load and hardness of material on
the wear under dry and sliding conditions. In the pin-on-disc rig, two
specimens were used; one, a pin is made of steel with a tip, positioned
perpendicular to the disc, where the disc is made of aluminium. The
pin wear and disc wear were measured by using the following
instruments: The Talysurf instrument, a digital microscope, and the
alicona instrument. The Talysurf profilometer was used to measure
the pin/disc wear scar depth, digital microscope was used to measure
the diameter and width of wear scar, and the alicona was used to
measure the pin wear and disc wear. After that, the Archard model,
American Society for Testing and Materials model (ASTM), and
neural network model were used for pin/disc wear modelling.
Simulation results were implemented by using the Matlab program.
This paper focuses on how the alicona can be used for wear
measurements and how the neural network can be used for wear
estimation.
Abstract: The objective of this study was to identify the optimal
level of partial replacement of Portland cement by the ashes
originating from burning straw and bagasse from sugar cane (ASB).
Order to this end, were made five series of flat plates and cylindrical
bodies: control and others with the partial replacement in 20, 30, 40
and 50% of ASB in relation to the mass of the Ordinary Portland
cement, and conducted a mechanical testing of simple axial
compression (cylindrical bodies) and the four-point bending (flat
plates) and determined water absorption (WA), bulk density (BD)
and apparent void volume (AVV) on both types of specimens. Based
on the data obtained, it may be noted that the control treatment
containing only Portland cement, obtained the best results. However,
the cylindrical bodies with 20% ashes showed better results
compared to the other treatments. And in the formulations plates, the
treatment which showed the best results was 30% cement
replacement by ashes.
Abstract: The concentration levels of six heavy metals (Cd, Cr,
Fe, Ni, Pb and Zn) and two mineral elements (Ca and Mg) were
determined in soil samples collected from the vicinity of two auto
mechanic workshops in Sabon-Gari, Kaduna state, Nigeria, using
Atomic Absorption Spectrometry (AAS), in order to compare the
gradation of their concentrations with distance and depth of soil from
the workshop sites. At site 1, concentrations of Lead, Chromium, Iron
and Zinc were generally found to be above the World Health
Organization limits, while those of Nickel and Cadmium fell within
the limits. Iron had the highest concentration with a range of 176.274
ppm to 489.127 ppm at depths of 5 cm to 15 cm and a distance range
of 5 m to 15 m, while the concentration of cadmium was least with a
range of 0.001 ppm to 0.008 ppm at similar depth and distance
ranges. In addition, there was more of calcium (11.521 ppm to
121.709 ppm), in all the samples, than magnesium (11.293 ppm to
21.635 ppm). Similar results were obtained for site II. The
concentrations of all the metals analyzed showed a downward
gradient with increase in depth and distance from both workshop sites
except for iron and zinc at site 2. The immediate and remote
implications of these findings on the biota are discussed.