Abstract: Emulsion formation is unavoidable and can be detrimental to an oil field production. The presence of stable emulsions also reduces the quality of crude oil and causes more problems in the downstream refinery operations, such as corrosion and pipeline pressure drop. Hence, it is important to know the effects of emulsions in the pipeline. Light crude oil was used for the continuous phase in the W/O emulsions where the emulsions pass through a flow loop to test the pressure drop across the pipeline. The results obtained shows that pressure drop increases as water cut is increased until it peaks at the phase inversion of the W/O emulsion between 30% to 40% water cut. Emulsions produced by gradual constrictions show a lower stability as compared to sudden constrictions. Lower stability of emulsions in gradual constriction has the higher influence of pressure drop compared to a sudden sharp decrease in diameter in sudden constriction. Generally, sudden constriction experiences pressure drop of 0.013% to 0.067% higher than gradual constriction of the same ratio. Lower constriction ratio cases cause larger pressure drop ranging from 0.061% to 0.241%. Considering the higher profitability in lower emulsion stability and lower pressure drop at the developed flow region of different constrictions, an optimum design of constriction is found to be gradual constriction with a ratio of 0.5.
Abstract: Automotive designers have been trying to use dimples to reduce drag in vehicles. In this work, a car model has been applied with dimple surface with a parameter called dimple ratio DR, the ratio between the depths of the half dimple over the print diameter of the dimple, has been introduced and numerically simulated via k-ε turbulence model to study the aerodynamics performance with the increasing depth of the dimples The Ahmed body car model with 25 degree slant angle is simulated with the DR of 0.05, 0.2, 0.3 0.4 and 0.5 at Reynolds number of 176387 based on the frontal area of the car model. The geometry of dimple changes the kinematics and dynamics of flow. Complex interaction between the turbulent fluctuating flow and the mean flow escalates the turbulence quantities. The maximum level of turbulent kinetic energy occurs at DR = 0.4. It can be concluded that the dimples have generated extra turbulence energy at the surface and as a result, the application of dimples manages to reduce the drag coefficient of the car model compared to the model with smooth surface.
Abstract: Improvement in vehicle efficiency can reduce global fossil fuels consumptions. For that sole reason, Shell Global Corporation introduces Shell Eco-marathon where student teams require to design, build and test energy-efficient vehicles. Hence, this paper will focus on design processes and the development of a fuel economic vehicle which satisfying the requirements of the competition. In this project, three components are designed and analyzed, which are the body, chassis and powertrain of the vehicle. Optimum design for each component is produced through simulation analysis and theoretical calculation in which improvement is made as the project progresses.
Abstract: Ocean current is always available around the
surrounding of SHELL Sabah Water Platform and data are collected
every 10 minutes, 24 hours a day, for a period of 365 days. Due to
low current speed, conventional hydrokinetic power generation is not
feasible, thus leading to the study of low current enabled vortex
induced vibration power generation application. In this case, the
design of a vortex induced vibration application is studied to obtain
an optimum design for the VIV oscillator. Power output is then
determined to study the feasibility of the VIV application in low
current condition.
Abstract: There have been rigorous research and development
of unmanned aerial vehicles in the field of search and rescue (SAR)
operation recently. UAVs reduce unnecessary human risks while
assisting rescue efforts through aerial imagery, topographic mapping
and emergency delivery. The application of UAVs in offshore and
nearshore marine SAR missions is discussed in this paper. Projects
that integrate UAV technology into their systems are introduced to
highlight the great advantages and capabilities of UAVs. Scenarios
where UAVs could provide invaluable assistance are also suggested.
Abstract: For a bluff body, dimples behave like roughness
elements in stimulating a turbulent boundary layer, leading to delayed
flow separation, a smaller wake and lower form drag. This is very
different in principle from the application of dimples to streamlined
body, where any reduction in drag would be predominantly due to a
reduction in skin friction. In the present work, a car model with
different dimple geometry is simulated using k-ε turbulence modeling
to determine its effect to the aerodynamics performance. Overall, the
results show that the application of dimples manages to reduce the
drag coefficient of the car model.
Abstract: The in-cylinder flow and mixture formations are
significant in view of today’s increasing concern on environmental
issues and stringent emission regulations. In this paper, the numerical
simulations of a SI engine at different engine speeds (2000-5000
rpm) at fixed intake flow pressure of 1 bar are studied using the AVL
FIRE software. The simulation results show that when the engine
speed at fixed intake flow pressure is increased, the volumetric
efficiency of the engine decreases. This is due to a richer fuel
conditions near the engine cylinder wall when engine speed is
increased. Significant effects of impingement are also noted on the
upper and side walls of the engine cylinder. These variations in
mixture formation before ignition could affect the thermodynamics
efficiency and specific fuel consumption that would lead to a reduced
engine performance.
Abstract: The global demand for continuous and eco-friendly
renewable energy as alternative to fossils fuels is large and ever
growing in nowadays. This paper will focus on capability of Vortex
Induced Vibration (VIV) phenomenon in generating alternative
energy for offshore platform application. In order to maximize the
potential of energy generation, the effects of lock in phenomenon and
different geometries of cylinder were studied in this project. VIV is
the motion induced on bluff body which creates alternating lift forces
perpendicular to fluid flow. Normally, VIV is unwanted in order to
prevent mechanical failure of the vibrating structures. But in this
project, instead of eliminating these vibrations, VIV will be exploited
to transform these vibrations into a valuable resource of energy.