Abstract: In insulation and cooling of power transformers
various liquids are used. Mineral oils have wide availability and low
cost. However, they have a poor biodegradability potential and lower
fire point in comparison with other insulating liquids. Use of a liquid
having high biodegradability is important due to environmental
consideration. This paper investigates edible corn oil as an alternative
to mineral oil. Various properties of mineral and corn oil like
breakdown voltage, dissipation factor, relative dielectric constant,
power loss and resistivity were measured according to different
standards.
Abstract: The composite flour blend consisting of corn, pearl
millet, black gram and wheat bran in the ratio of 80:5:10:5 was taken
to prepare the extruded product and their effect on physical properties
of extrudate was studied. The extrusion process was conducted in
laboratory by using twin screw extruder. The physical characteristics
evaluated include lateral expansion, bulk density, water absorption
index, water solubility index, and rehydration ratio and moisture
retention. The Central Composite Rotatable Design (CCRD) was
used to decide the level of processing variables i.e. feed moisture
content (%), screw speed (rpm), and barrel temperature (oC) for the
experiment. The data obtained after extrusion process were analyzed
by using response surface methodology. A second order polynomial
model for the dependent variables was established to fit the
experimental data. The numerical optimization studies resulted in
127°C of barrel temperature, 246 rpm of screw speed, and 14.5% of
feed moisture as optimum variables to produce acceptable extruded
product. The responses predicted by the software for the optimum
process condition resulted in lateral expansion 126%, bulk density
0.28 g/cm3, water absorption index 4.10 g/g, water solubility index
39.90%, rehydration ratio 544% and moisture retention 11.90% with
75% desirability.
Abstract: Efficient use of energy, the increase in demand of
energy and also with the reduction of natural energy sources, has
improved its importance in recent years. Most of the losses in the
system from electricity produced until the point of consumption is
mostly composed by the energy distribution system. In this study,
analysis of the resulting loss in power distribution transformer and
distribution power cable is realized which are most of the losses in
the distribution system. Transformer losses in the real distribution
system are analyzed by CYME Power Engineering Software
program. These losses are disclosed for different voltage levels and
different loading conditions.
Abstract: Geographical routing protocol requires node physical
location information to make forwarding decision. Geographical
routing uses location service or position service to obtain the position
of a node. The geographical information is a geographic coordinates
or can be obtained through reference points on some fixed coordinate
system. Link can be formed between two nodes. Link lifetime plays a
crucial role in MANET. Link lifetime represent how long the link is
stable without any failure between the nodes. Link failure may occur
due to mobility and because of link failure energy of nodes can be
drained. Thus this paper proposes survey about link lifetime
prediction using geographical information.
Abstract: Tannase (tannin acyl hydrolase, E.C.3.1.1.20) is an
important hydrolysable enzyme with innumerable applications and
industrial potential. In the present study, a kinetic model has been
developed for the batch fermentation used for the production of
tannase by A.flavus MTCC 3783. Maximum tannase activity of
143.30 U/ml was obtained at 96 hours under optimum operating
conditions at 35oC, an initial pH of 5.5 and with an inducer tannic
acid concentration of 3% (w/v) for a fermentation period of 120
hours. The biomass concentration reaches a maximum of 6.62 g/l at
96 hours and further there was no increase in biomass concentration
till the end of the fermentation. Various unstructured kinetic models
were analyzed to simulate the experimental values of microbial
growth, tannase activity and substrate concentration. The Logistic
model for microbial growth , Luedeking - Piret model for production
of tannase and Substrate utilization kinetic model for utilization of
substrate were capable of predicting the fermentation profile with
high coefficient of determination (R2) values of 0.980, 0.942 and
0.983 respectively. The results indicated that the unstructured models
were able to describe the fermentation kinetics more effectively.
Abstract: In this paper, the secure BioSemantic Scheme is
presented to bridge biological/biomedical research problems and
computational solutions via semantic computing. Due to the diversity
of problems in various research fields, the semantic capability
description language (SCDL) plays and important role as a common
language and generic form for problem formalization. SCDL is
expected the essential for future semantic and logical computing in
Biosemantic field. We show several example to Biomedical problems
in this paper. Moreover, in the coming age of cloud computing, the
security problem is considered to be crucial issue and we presented a
practical scheme to cope with this problem.
Abstract: Spacer grid assembly supporting the nuclear fuel rods
is an important concern in the design of structural components of a
Pressurized Water Reactor (PWR). The spacer grid is composed by
springs and dimples which are formed from a strip sheet by means of
blanking and stamping processes. In this paper, the blanking process
and tooling parameters are evaluated by means of a 2D plane-strain
finite element model in order to evaluate the punch load and quality
of the sheared edges of Inconel 718 strips used for nuclear spacer
grids. A 3D finite element model is also proposed to predict the
tooling loads resulting from the stamping process of a preformed
Inconel 718 strip and to analyse the residual stress effects upon the
spring and dimple design geometries of a nuclear spacer grid.
Abstract: This paper presents the local mesh co-occurrence
patterns (LMCoP) using HSV color space for image retrieval system.
HSV color space is used in this method to utilize color, intensity and
brightness of images. Local mesh patterns are applied to define the
local information of image and gray level co-occurrence is used to
obtain the co-occurrence of LMeP pixels. Local mesh co-occurrence
pattern extracts the local directional information from local mesh
pattern and converts it into a well-mannered feature vector using gray
level co-occurrence matrix. The proposed method is tested on three
different databases called MIT VisTex, Corel, and STex. Also, this
algorithm is compared with existing methods, and results in terms of
precision and recall are shown in this paper.
Abstract: In this paper, influence of harmonics on medium
voltage distribution system of Bogazici Electricity Distribution Inc.
(BEDAS) which takes place at Istanbul/Turkey is investigated. A ring
network consisting of residential loads is taken into account for this
study. Real system parameters and measurement results are used for
simulations. Also, probable working conditions of the system are
analyzed for 50%, 75%, and 100% loading of transformers with
similar harmonic contents. Results of the study are exhibited the
influence of nonlinear loads on %THDV, P.F. and technical losses of
the medium voltage distribution system.
Abstract: In this paper, we present a four-step ortho-rectification
procedure for real-time geo-referencing of video data from a low-cost
UAV equipped with a multi-sensor system. The basic procedures for
the real-time ortho-rectification are: (1) decompilation of the video
stream into individual frames; (2) establishing the interior camera
orientation parameters; (3) determining the relative orientation
parameters for each video frame with respect to each other; (4)
finding the absolute orientation parameters, using a self-calibration
bundle and adjustment with the aid of a mathematical model. Each
ortho-rectified video frame is then mosaicked together to produce a
mosaic image of the test area, which is then merged with a well
referenced existing digital map for the purpose of geo-referencing
and aerial surveillance. A test field located in Abuja, Nigeria was
used to evaluate our method. Video and telemetry data were collected
for about fifteen minutes, and they were processed using the four-step
ortho-rectification procedure. The results demonstrated that the
geometric measurement of the control field from ortho-images is
more accurate when compared with those from original perspective
images when used to pin point the exact location of targets on the
video imagery acquired by the UAV. The 2-D planimetric accuracy
when compared with the 6 control points measured by a GPS receiver
is between 3 to 5 metres.
Abstract: In present global scenario, aluminum alloys are
coining the attention of many innovators as competing structural
materials for automotive and space applications. Comparing to other
challenging alloys, especially, 7xxx series aluminum alloys have
been studied seriously because of benefits such as moderate strength;
better deforming characteristics and affordable cost. It is expected
that substitution of aluminum alloys for steels will result in great
improvements in energy economy, durability and recyclability.
However, it is necessary to improve the strength and the formability
levels at low temperatures in aluminum alloys for still better
applications. Aluminum–Zinc–Magnesium with or without other
wetting agent denoted as 7XXX series alloys are medium strength
heat treatable alloys. In addition to Zn, Mg as major alloying
additions, Cu, Mn and Si are the other solute elements which
contribute for the improvement in mechanical properties by suitable
heat treatment process. Subjecting to suitable treatments like age
hardening or cold deformation assisted heat treatments; known as low
temperature thermomechanical treatments (LTMT) the challenging
properties might be incorporated. T6 is the age hardening or
precipitation hardening process with artificial aging cycle whereas T8
comprises of LTMT treatment aged artificially with X% cold
deformation. When the cold deformation is provided after solution
treatment, there is increase in hardness related properties such as
wear resistance, yield and ultimate strength, toughness with the
expense of ductility. During precipitation hardening both hardness
and strength of the samples are increasing. The hardness value may
further improve when room temperature deformation is positively
supported with age hardening known as thermomechanical treatment.
It is intended to perform heat treatment and evaluate hardness, tensile
strength, wear resistance and distribution pattern of reinforcement in
the matrix. 2 to 2.5 and 3 to 3.5 times increase in hardness is reported
in age hardening and LTMT treatments respectively as compared to
as-cast composite. There was better distribution of reinforcements in
the matrix, nearly two fold increase in strength levels and up to 5
times increase in wear resistance are also observed in the present
study.
Abstract: Despite the advances made in various new
technologies, application of these technologies for agriculture still
remains a formidable task, as it involves integration of diverse
domains for monitoring the different process involved in agricultural
management. Advances in ambient intelligence technology represents
one of the most powerful technology for increasing the yield of
agricultural crops and to mitigate the impact of water scarcity,
climatic change and methods for managing pests, weeds and diseases.
This paper proposes a GPS-assisted, machine to machine solutions
that combine information collected by multiple sensors for the
automated management of paddy crops. To maintain the economic
viability of paddy cultivation, the various techniques used in
agriculture are discussed and a novel system which uses ambient
intelligence technique is proposed in this paper. The ambient
intelligence based agricultural system gives a great scope.
Abstract: Present work deals with the possible use of fertigation
in agriculture and its impact on the availability of mineral nitrogen
(Nmin) in topsoil and subsoil horizons. The aim of the present study is
to demonstrate the effect of the organic matter presence in fertigation
on microbial transformation and availability of mineral nitrogen
forms. The main investigation reason is the potential use of pretreated
waste water, as a source of organic carbon (Corg) and residual
nutrients (Nmin) for fertigation. Laboratory experiment has been
conducted to demonstrate the effect of the arable land fertilization
method on the Nmin availability in different depths of the soil with
the usage of model experimental containers filled with soil from
topsoil and podsoil horizons that were taken from the precise area.
Tufted hairgrass (Deschampsia caespitosa) has been chosen as a
model plant. The water source protection zone Brezova nad Svitavou
has been a research area where significant underground reservoirs of
drinking water of the highest quality are located. From the second
half of the last century local sources of drinking water show
nitrogenous compounds increase that get here almost only from
arable lands. Therefore, an attention of the following text focuses on
the fate of mineral nitrogen in the complex plant-soil. Research
results show that the fertigation application with Corg in a
combination with mineral fertilizer can reduce the amount of Nmin
leached from topsoil horizon of agricultural soils. In addition, some
plants biomass production reduces may occur.
Abstract: This paper aims to project the construction of a
prototype azimuthal thruster, mounted with materials of low cost and
easy access, testing in a controlled environment to measure their
performance, characteristics and feasibility of future projects. The
construction of the simulation of dynamic positioning software,
responsible for simulating a vessel and reposition it when necessary.
Validation tests were performed in the form of partial or complete
system. These tests validate the system manually or automatically.
The system provides an interface to the user and simulates the
conditions unfavorable positioning of a vessel, accurately calculates
the azimuth angle, the direction of rotation of the helix and the time
that this should be turned on so that the vessel back to position
original. A serial communication connects the Simulation Dynamic
Positioning System with Embedded System causing the usergenerated
data to simulate the DP system arrives in the form of
control signals to the motors of the propellant. This article addresses
issues in the marine industry employees.
Abstract: The study is in application and analysis of two tourism
management tools that can contribute to making public managers
decision: the Barometer of Tourism Sustainability (BTS) and the
Ecological Footprint (EF). The results have shown that BTS allows
you to have an integrated view of the tourism system, awakening to
the need for planning of appropriate actions so that it can achieve the
positive scale proposed (potentially sustainable). Already the
methodology of ecological tourism footprint is an important tool to
measure potential impacts generated by tourism to tourist reality.
Abstract: In this study, lipid-deprived residuals of microalgae
were hydrolyzed for the production of reducing sugars by using the
recombinant Bacillus cellulosome, carrying eight genes from the
Clostridium thermocellum ATCC27405. The obtained cellulosome
was found to exist mostly in the broth supernatant with a cellulosome
activity of 2.4 U/mL. Furthermore, the Michaelis-Menten constant
(Km) and Vmax of cellulosome were found to be 14.832 g/L and 3.522
U/mL. The activation energy of the cellulosome to hydrolyze
microalgae LDRs was calculated as 32.804 kJ/mol.
Abstract: The work aims to develop a robot in the form of
autonomous vehicle to detect, inspection and mapping of
underground pipelines through the ATmega328 Arduino platform.
Hardware prototyping is very similar to C / C ++ language that
facilitates its use in robotics open source, resembles PLC used in
large industrial processes. The robot will traverse the surface
independently of direct human action, in order to automate the
process of detecting buried pipes, guided by electromagnetic
induction. The induction comes from coils that send the signal to the
Arduino microcontroller contained in that will make the difference in
intensity and the treatment of the information, and then this
determines actions to electrical components such as relays and
motors, allowing the prototype to move on the surface and getting the
necessary information. This change of direction is performed by a
stepper motor with a servo motor. The robot was developed by
electrical and electronic assemblies that allowed test your application.
The assembly is made up of metal detector coils, circuit boards and
microprocessor, which interconnected circuits previously developed
can determine, process control and mechanical actions for a robot
(autonomous car) that will make the detection and mapping of buried
pipelines plates. This type of prototype can prevent and identifies
possible landslides and they can prevent the buried pipelines suffer an
external pressure on the walls with the possibility of oil leakage and
thus pollute the environment.
Abstract: The rapid growth of multimedia technology demands
the secure and efficient access to information. This fast growing lose
the confidence of unauthorized duplication. Henceforth the protection
of multimedia content is becoming more important. Watermarking
solves the issue of unlawful copy of advanced data. In this paper,
blind video watermarking technique has been proposed. A luminance
layer of selected frames is interlaced into two even and odd rows of
an image, further it is deinterlaced and equalizes the coefficients of
the two shares. Color watermark is split into different blocks, and the
pieces of block are concealed in one of the share under the wavelet
transform. Stack the two images into a single image by introducing
interlaced even and odd rows in the two shares. Finally, chrominance
bands are concatenated with the watermarked luminance band. The
safeguard level of the secret information is high, and it is
undetectable. Results show that the quality of the video is not
changed also yields the better PSNR values.
Abstract: Since 1920, the industry has almost completely
changed the rivets production techniques for the manufacture of
permanent welding join production of structures and manufacture of
other products. The welding arc is the process more widely used in
industries. This is accomplished by the heat of an electric arc which
melts the base metal while the molten metal droplets are transferred
through the arc to the welding pool, protected from the atmosphere
by a gas curtain. The GMAW (Gas metal arc welding) process is
influenced by variables such as: current, polarity, welding speed,
electrode: extension, position, moving direction; type of joint,
welder's ability, among others. It is remarkable that the knowledge
and control of these variables are essential for obtaining satisfactory
quality welds, knowing that are interconnected so that changes in one
of them requiring changes in one or more of the other to produce the
desired results. The optimum values are affected by the type of base
metal, the electrode composition, the welding position and the quality
requirements. Thus, this paper proposes a new methodology, adding
the variable vibration through a mechanism developed for GMAW
welding, in order to improve the mechanical and metallurgical
properties which does not affect the ability of the welder and enables
repeatability of the welds made. For confirmation metallographic
analysis and mechanical tests were made.
Abstract: While choosing insulating oil, characteristic features
such as thermal cooling, endurance, efficiency and being
environment-friendly should be considered. Mineral oils are referred
as petroleum-based oil. In this study, vegetable oils investigated as an
alternative insulating liquid to mineral oil. Dissipation factor,
breakdown voltage, relative dielectric constant and resistivity
changes with the frequency and voltage of mineral, rapeseed and nut
oils were measured. Experimental studies were performed according
to ASTM D924 and IEC 60156 standards.