Abstract: Prestressed concrete is used a lot in infrastructures such as roads or bridges. However, poor grout filling and PC steel corrosion are currently major issues of prestressed concrete structures. One of the problems with nondestructive corrosion detection of PC steel is a plastic pipe which covers PC steel. The insulative property of pipe makes a nondestructive diagnosis difficult; therefore a practical technology to detect these defects is necessary for the maintenance of infrastructures. The goal of the research is a development of an electrochemical technique which enables to detect internal defects from the surface of prestressed concrete nondestructively. Ideally, the measurements should be conducted from the surface of structural members to diagnose non-destructively. In the present experiment, a prestressed concrete member is simplified as a layered specimen to simulate a current path between an input and an output electrode on a member surface. The specimens which are layered by mortar and the prestressed concrete constitution materials (steel, polyethylene, stainless steel, or galvanized steel plates) were provided to the alternating current impedance measurement. The magnitude of an applied electric field was 0.01-volt or 1-volt, and the frequency range was from 106 Hz to 10-2 Hz. The frequency spectrums of impedance, which relate to charge reactions activated by an electric field, were measured to clarify the effects of the material configurations or the properties. In the civil engineering field, the Nyquist diagram is popular to analyze impedance and it is a good way to grasp electric relaxation using a shape of the plot. However, it is slightly not suitable to figure out an influence of a measurement frequency which is reciprocal of reaction time. Hence, Bode diagram is also applied to describe charge reactions in the present paper. From the experiment results, the alternating current impedance method looks to be applicable to the insulative material measurement and eventually prestressed concrete diagnosis. At the same time, the frequency spectrums of impedance show the difference of the material configuration. This is because the charge mobility reflects the variety of substances and also the measuring frequency of the electric field determines migration length of charges which are under the influence of the electric field. However, it could not distinguish the differences of the material thickness and is inferred the difficulties of prestressed concrete diagnosis to identify the amount of an air void or a layer of corrosion product by the technique.
Abstract: The main objective of this study is to investigate basic properties of different natural clays, by two methods. The first method is a gas phase conversion of methylbutynol (MBOH). The second method is the application of Pyrrole-tpd. Based on the product distribution from the first method, the acidic, basic and coordinately unsaturated sites were differentiated. It was shown that both the conversion and the selectivity for basic products did not change with reaction time. Nevertheless, a deviation from the stoichiometric ratio R of formed acetylene to acetone was observed (R=0.8…0.97). The conversion normalized to the surface area was used for establishing the activity sequence: White kaolinite > red kaolinite > bentonite > zeolite > diatomite. In addition, the results were compared with synthetic amorphous alumosilicates and typical basic materials like MgO and ZnO. The basic properties were characterized using the Pyrrole-tpd. The Pyrrole-tpd results showed the same basicity sequence as the MBOH gas phase reaction.
Abstract: The aim of this study was to investigate the effectiveness of memory training exercise on cognitive flexibility. The method of this study was experimental. The statistical population selected 40 students 14 years old, samples were chosen by available sampling method and then they were replaced in experimental (training program) group and control group randomly and answered to Wisconsin Card Sorting Test; covariance test results indicated that there were a significant in post-test scores of experimental group (p
Abstract: Zinc borates are used as a multi-functional flame
retardant additive for its high dehydration temperature. In this study,
the method of ultrasonic mixing was used in the synthesis of zinc
borates. The reactants of zinc oxide (ZnO) and boric acid (H3BO3)
were used at the constant reaction parameters of 90°C reaction
temperature and 55 min of reaction time. Several molar ratios of
ZnO:H3BO3 (1:1, 1:2, 1:3, 1:4 and 1:5) were conducted for the
determination of the optimum reaction ratio. Prior to synthesis the
characterization of the synthesized zinc borates were made by X-Ray
Diffraction (XRD) and Fourier Transform Infrared Spectroscopy
(FT-IR). From the results Zinc Oxide Borate Hydrate
[Zn3B6O12.3.5H2O], were synthesized optimum at the molar ratio of
1:3, with a reaction efficiency of 95.2%.
Abstract: Hydrothermal liquefaction (HTL) is a technique for obtaining clean biofuel from biomass in the presence of heat and pressure in an aqueous medium which leads to a decomposition of this biomass to the formation of various products. A role of operating conditions is essential for the bio-oil and other products’ yield and also quality of the products. The effects of these parameters were investigated in regards to the composition and yield of the products. Chlorellaceae microalgae were tested under different HTL conditions to clarify suitable conditions for extracting bio-oil together with value-added co-products. Firstly, different microalgae loading rates (5-30%) were tested and found that this parameter has not much significant to product yield. Therefore, 10% microalgae loading rate was selected as a proper economical solution for conditioned schedule at 250oC and 30 min-reaction time. Next, a range of temperature (210-290oC) was applied to verify the effects of each parameter by keeping the reaction time constant at 30 min. The results showed no linkage with the increase of the reaction temperature and some reactions occurred that lead to different product yields. Moreover, some nutrients found in the aqueous product are possible to be utilized for nutrient recovery.
Abstract: In Jordan having deficit atmospheric precipitation, an
increase in water demand occurs during summer months. Jordan can
be regarded with a relatively high potential for wastewater recycling
and reuse. The main purpose of this paper was to investigate the
removal of total suspended solids (TSS) and chemical oxygen
demand (COD) for olive mill wastewater (OMW) by
electrocoagulation (EC) process. In the combination of
electrocoagulation by using coupled iron–aluminum electrodes, the
optimum working pH was found to be around 6. Results indicated
that the electrocoagulation process allowed removal of TSS and COD
of about 82.5% and 47.5%, respectively at 45 mA/cm2 after 70
minutes by using coupled iron–aluminum electrodes. It was
demonstrated that the maximum TSS and COD removals were
obtained at some optimum experimental parameters for current
density, pH, and reaction time.
Abstract: In this research, copper borates are synthesized by the
reaction of copper sulfate pentahydrate (CuSO4.5H2O) and
tincalconite (Na2O4B7.10H2O). The experimental parameters are
selected as 80oC reaction temperature and 60 of reaction time. The
effect of mole ratio of CuSO4.5H2O to Na2O4B7.5H2O is studied. For
the identification analyses X-Ray Diffraction (XRD) and Fourier
Transform Infrared Spectroscopy (FT-IR) techniques are used. At the
end of the experiments, synthesized copper borate is matched with
the powder diffraction file of “00-001-0472” [Cu(BO2)2] and
characteristic vibrations between B and O atoms are seen. The proper
crystals are obtained at the mole ratio of 3:1. This study showed that
simplified synthesis process is suitable for the production of copper
borate minerals.
Abstract: The objective of this study is to investigate the performance of the electrocoagulation process for color and COD removal in palm oil wastewater using a 10 L batch reactor. Iron was used as electrodes and the distance between electrodes was 2 cm. The effects of operating parameters: current voltage (6, 12 and 18 volt), reaction time (5, 15, 30, 45 and 60 min) and initial pH (4 and 9) of treatment efficiency were examine. The result showed that decolorization and COD removal efficiency increased with the increase in current voltage and reaction time. The proper condition for decolorization achieved at initial pH 4 and 9 were current voltage of 12 volt, reaction time 30 min. The decolorization efficiency reached 90.4% and 88.9%, respectively. COD removal was achiveved at current voltage 12 volt, reaction time 15 min. COD removal efficiency was 89.2 % and 83.0%, respectively. From the results, to show electrocoagulation process can treat palm oil mill wastewater in both acidic and basic condition at high efficiency for color and COD removal. Consequently, electrocoagulation process can be used or applied as a post-treatment step to improve the quality of the final discharge in term of color and residual COD removal.
Abstract: Paced Auditory Serial Addition Test (PASAT) has
been used as a common research tool for different neurological
disorders like Multiple Sclerosis. Recently, technology let
researchers to introduce a new versions of the visual test, the paced
visual serial addition test (PVSAT). In this paper, the computerized
version of these two tests is introduced. Beside the number of true
responses are interpreted, the reaction time of subjects are calculated
by the software. We hypothesize that paying attention to the reaction
time may be valuable. For this purpose, sixty eight female normal
subjects and fifty eight male normal subjects are enrolled in the
study. We investigate the similarity between the PASAT3 and
PVSAT3 in number of true responses and the new criterion (the
average reaction time of each subject). The similarity between two
tests were rejected (p-value = 0.000) which means that these two test
differ. The effect of sex in the tests were not approved since the pvalues
of different between PASAT3 and PVSAT3 in both sex is the
same (p-value = 0.000) which means that male and female subjects
performed the tests at no different level of performance. The new
criterion shows a negative correlation with the age which offers aged
normal subjects may have the same number of true responses as the
young subjects but they have latent responses. This will give prove
for the importance of reaction time.
Abstract: In this study, the transesterification of palm oil with methanol for biodiesel production was studied by using CaO–ZnO as a heterogeneous base catalyst prepared by incipient-wetness impregnation (IWI) and co-precipitation (CP) methods. The reaction parameters considered were molar ratio of methanol to oil, amount of catalyst, reaction temperature, and reaction time. The optimum conditions–15:1 molar ratio of methanol to oil, a catalyst amount of 6 wt%, reaction temperature of 60 °C, and reaction time of 8 h–were observed. The effects of Ca loading, calcination temperature, and catalyst preparation on the catalytic performance were studied. The fresh and spent catalysts were characterized by several techniques, including XRD, TPR, and XRF.
Abstract: In this paper, naturally immobilized lipase, Carica
papaya lipase, catalyzed biodiesel production from fish oil was
studied. The refined fish oil, extracted from the discarded parts of
fish, was used as a starting material for biodiesel production. The
effects of molar ratio of oil: methanol, lipase dosage, initial water
activity of lipase, temperature and solvent were investigated. It was
found that Carica papaya lipase was suitable for methanolysis of fish
oil to produce methyl ester. The maximum yield of methyl ester
could reach up to 83% with the optimal reaction conditions: oil:
methanol molar ratio of 1: 4, 20% (based on oil) of lipase, initial
water activity of lipase at 0.23 and 20% (based on oil) of tert-butanol
at 40oC after 18 h of reaction time. There was negligible loss in
lipase activity even after repeated use for 30 cycles.
Abstract: Theobjective of this study was to evaluate the optimal
treatment condition of Fenton oxidation process to removal
contaminant in soil slurry contaminated by petroleum hydrocarbons.
This research studied somefactors that affect the removal efficiency
of petroleum hydrocarbons in soil slurry including molar ratio of
hydrogen peroxide (H2O2) to ferrous ion(Fe2+), pH condition and
reaction time.The resultsdemonstrated that the optimum condition
was that the molar ratio of H2O2:Fe3+ was 200:1,the pHwas 4.0and
the rate of reaction was increasing rapidly from starting point to 7th
hour and destruction kinetic rate (k) was 0.24 h-1. Approximately
96% of petroleum hydrocarbon was observed(initialtotal petroleum
hydrocarbon (TPH) concentration = 70±7gkg-1)
Abstract: The dilute acid pretreatment and enzymatic
saccharification of lignocellulosic substrate, cogon grass (Imperata
cylindrical, L.) was optimized prior ethanol fermentation using
simultaneous saccharification and fermentation (SSF) method. The
optimum pretreatment conditions, temperature, sulfuric acid
concentration, and reaction time were evaluated by determining the
maximum sugar yield at constant enzyme loading. Cogon grass, at
10% w/v substrate loading, has optimum pretreatment conditions of
126°C, 0.6% v/v H2SO4, and 20min reaction time. These
pretreatment conditions were used to optimize enzymatic
saccharification using different enzyme combinations. The maximum
saccharification yield of 36.68mg/mL (71.29% reducing sugar) was
obtained using 25FPU/g-cellulose cellulase complex combined with
1.1% w/w of cellobiase, ß-glucosidase, and 0.225% w/w of
hemicellulase complex, after 96 hours of saccharification. Using the
optimum pretreatment and saccharification conditions, SSF of treated
substrates was done at 37°C for 120 hours using industrial yeast
strain HBY3, Saccharomyces cerevisiae. The ethanol yield for cogon
grass at 4% w/w loading was 9.11g/L with 5.74mg/mL total residual
sugar.
Abstract: Optimization study of the diesters biolubricant oleyl 9(12)-hydroxy-10(13)-oleioxy-12(9)-octadecanoate (OLHYOOT) was synthesized in the presence of sulfuric acid (SA) as catalyst has been done. Optimum conditions of the experiment to obtain high yield% of OLHYOOT were predicted at ratio of OL/HYOOA of 1:1 g/g, ratio of SA/HYOOA of 0.20:1 g/g, reaction temperature 110 °C and 4.5 h of reaction time. At this condition, the Yield% of OLHYOOT was 88.7. Disappearance of carboxylic acid (C=O) peak has observed by FTIR with appearance ester (C=O) at 1738 cm-1. 1H NMR spectra analyses confirmed the result of OLHYOOT with appearance ester (-CHOCOR) at 4.05ppm and also the 13C-NMR confirmed the result with appearance ester (C=O) peak at 173.93ppm.