Abstract: In this paper the behavior of fixed series compensated
extra high voltage transmission lines during faults is simulated. Many
over-voltage protection schemes for series capacitors are limited in
terms of size and performance, and are easily affected by
environmental conditions. While the need for more compact and
environmentally robust equipment is required. use of series
capacitors for compensating part of the inductive reactance of long
transmission lines increases the power transmission capacity.
Emphasis is given on the impact of modern capacitor protection
techniques (MOV protection). The simulation study is performed
using MATLAB/SIMULINK®and results are given for a three phase
and a single phase to ground fault.
Abstract: In this paper, a fast motion compensation algorithm is
proposed that improves coding efficiency for video sequences with
brightness variations. We also propose a cross entropy measure
between histograms of two frames to detect brightness variations. The
framewise brightness variation parameters, a multiplier and an offset
field for image intensity, are estimated and compensated. Simulation
results show that the proposed method yields a higher peak signal to
noise ratio (PSNR) compared with the conventional method, with a
greatly reduced computational load, when the video scene contains
illumination changes.
Abstract: Synchronization is a difficult problem in CDMA
satellite communications. Due to the influence of additive noise and
fading in the mobile channel, it is not easy to keep up with the
attenuation and offset. This paper considers a recently proposed
approach to solve the problem of synchronization chaotic Chen
system in CDMA satellite communication in the presence of constant
attenuation and offset. An analytic algorithm that provides closed
form channel and carrier offset estimates is presented. The principle
of this approach is based on adding a compensation block before the
receiver to compensate the distortion of the imperfect channel by
using genetic algorithm.
The resultants presented, show that the receiver is able to recover
rapidly the synchronization with the transmitter.
Abstract: This paper presents an approach for daily optimal operation of distribution networks considering Distributed Generators (DGs). Due to private ownership of DGs, a cost based compensation method is used to encourage DGs in active and reactive power generation. The objective function is summation of electrical energy generated by DGs and substation bus (main bus) in the next day. A genetic algorithm is used to solve the optimal operation problem. The approach is tested on an IEEE34 buses distribution feeder.
Abstract: This paper aims to present the reviews of the
application of neural network in shunt active power filter (SAPF).
From the review, three out of four components of SAPF structure,
which are harmonic detection component, compensating current
control, and DC bus voltage control, have been adopted some of
neural network architecture as part of its component or even
substitution. The objectives of most papers in using neural network in
SAPF are to increase the efficiency, stability, accuracy, robustness,
tracking ability of the systems of each component. Moreover,
minimizing unneeded signal due to the distortion is the ultimate goal
in applying neural network to the SAPF. The most famous
architecture of neural network in SAPF applications are ADALINE
and Backpropagation (BP).
Abstract: In this paper, investigation of subsynchronous
resonance (SSR) characteristics of a hybrid series compensated
system and the design of voltage controller for three level 24-pulse
Voltage Source Converter based Static Synchronous Series
Compensator (SSSC) is presented. Hybrid compensation consists of
series fixed capacitor and SSSC which is a active series FACTS
controller. The design of voltage controller for SSSC is based on
damping torque analysis, and Genetic Algorithm (GA) is adopted for
tuning the controller parameters. The SSR Characteristics of SSSC
with constant reactive voltage control modes has been investigated.
The results show that the constant reactive voltage control of SSSC
has the effect of reducing the electrical resonance frequency, which
detunes the SSR.The analysis of SSR with SSSC is carried out based
on frequency domain method, eigenvalue analysis and transient
simulation. While the eigenvalue and damping torque analysis are
based on D-Q model of SSSC, the transient simulation considers both
D-Q and detailed three phase nonlinear system model using
switching functions.
Abstract: One major source of performance decline in speaker
recognition system is channel mismatch between training and testing.
This paper focuses on improving channel robustness of speaker
recognition system in two aspects of channel compensation technique
and channel robust features. The system is text-independent speaker
identification system based on two-stage recognition. In the aspect of
channel compensation technique, this paper applies MAP (Maximum
A Posterior Probability) channel compensation technique, which was
used in speech recognition, to speaker recognition system. In the
aspect of channel robust features, this paper introduces
pitch-dependent features and pitch-dependent speaker model for the
second stage recognition. Based on the first stage recognition to
testing speech using GMM (Gaussian Mixture Model), the system
uses GMM scores to decide if it needs to be recognized again. If it
needs to, the system selects a few speakers from all of the speakers
who participate in the first stage recognition for the second stage
recognition. For each selected speaker, the system obtains 3
pitch-dependent results from his pitch-dependent speaker model, and
then uses ANN (Artificial Neural Network) to unite the 3
pitch-dependent results and 1 GMM score for getting a fused result.
The system makes the second stage recognition based on these fused
results. The experiments show that the correct rate of two-stage
recognition system based on MAP channel compensation technique
and pitch-dependent features is 41.7% better than the baseline system
for closed-set test.
Abstract: Self-sensing estimates the air gap within an electro
magnetic path by analyzing the bearing coil current and/or voltage
waveform. The self-sensing concept presented in this paper has been
developed within the research project “Active Magnetic Bearings
with Supreme Reliability" and is used for position sensor fault
detection.
Within this new concept gap calculation is carried out by an alldigital
analysis of the digitized coil current and voltage waveform.
For analysis those time periods within the PWM period are used,
which give the best results. Additionally, the concept allows the
digital compensation of nonlinearities, for example magnetic
saturation, without degrading signal quality. This increases the
accuracy and robustness of the air gap estimation and additionally
reduces phase delays.
Beneath an overview about the developed concept first
measurement results are presented which show the potential of this
all-digital self-sensing concept.
Abstract: Adjacent Hall microsensors, comprising a silicon
substrate and four contacts, providing simultaneously two supply inputs and two differential outputs, are characterized. The voltage
related sensitivity is in the order of 0.11T-1, and a cancellation method for offset compensation is used, achieving residual offset in
the micro scale which is also compared to a single Hall plate.
Abstract: This paper presents the mathematical model and
control strategy on DQ frame of shunt active power filter. The
structure of the shunt active power filter is the voltage source inverter
(VSI). The pulse width modulation (PWM) with PI controller is used
in the paper. The concept of DQ frame to apply with the shunt active
power filter is described. Moreover, the detail of the PI controller
design for two current loops and one voltage loop are fully explained.
The DQ axis with Fourier (DQF) method is applied to calculate the
reference currents on DQ frame. The simulation results show that the
control strategy and the design method presented in the paper can
provide the good performance of the shunt active power filter.
Moreover, the %THD of the source currents after compensation can
follow the IEEE Std.519-1992.
Abstract: Green- spaces might be very attractive, but
where are the economic benefits? What value do nature and
landscape have for us? What difference will it make to jobs,
health and the economic strength of areas struggling with
deprivation and social problems? [1].There is a need to consider
green spaces from a different perspective. Green planning is not just
about flora and fauna, but also about planning for economic benefits
[2]. It is worth trying to quantify the value of green spaces since
nature and landscape are crucially important to our quality of life and
sustainable development. The reality, however, is that urban
development often takes place at the expense of green spaces.
Urbanization is an ongoing process throughout the world; however,
hyper-urbanization without environmental planning is destructive,
not constructive [3]. Urban spaces are believed to be more valuable
than other land uses, particular green areas, simply because of the
market value connected to urban spaces. However, attractive
landscapes can help raise the quality and value of the urban market
even more. In order to reach these objectives of integrated planning,
the Green-Value-Gap needs to be bridged. Economists have to
understand the concept of Green-Planning and the spinoffs, and
Environmentalists have to understand the importance of urban
economic development and the benefits thereof to green planning. An
interface between Environmental Management, Economic
Development and sustainable Spatial Planning are needed to bridge
the Green-Value-Gap.
Abstract: The paper deals with the comparison study of
harmonic detection methods for a shunt active power filter. The
%THD and the power factor value at the PCC point after
compensation are considered for the comparison. There are three
harmonic detection methods used in the paper that are synchronous
reference frame method, synchronous detection method, and DQ axis
with Fourier method. In addition, the ideal current source is used to
represent the active power filter by assuming an infinitely fast
controller action of the active power filter. The simulation results
show that the DQ axis with Fourier method provides the minimum
%THD after compensation compared with other methods. However,
the power factor value at the PCC point after compensation is slightly
lower than that of synchronous detection method.
Abstract: The objective of this paper is to design a model of human vital sign prediction for decreasing prediction error by using two states mapping based time series neural network BP (back-propagation) model. Normally, lot of industries has been applying the neural network model by training them in a supervised manner with the error back-propagation algorithm for time series prediction systems. However, it still has a residual error between real value and prediction output. Therefore, we designed two states of neural network model for compensation of residual error which is possible to use in the prevention of sudden death and metabolic syndrome disease such as hypertension disease and obesity. We found that most of simulations cases were satisfied by the two states mapping based time series prediction model compared to normal BP. In particular, small sample size of times series were more accurate than the standard MLP model. We expect that this algorithm can be available to sudden death prevention and monitoring AGENT system in a ubiquitous homecare environment.
Abstract: In this paper, we propose a novel adaptive
spatiotemporal filter that utilizes image sequences in order to remove
noise. The consecutive frames include: current, previous and next
noisy frames. The filter proposed in this paper is based upon the
weighted averaging pixels intensity and noise variance in image
sequences. It utilizes the Appropriate Number of Consecutive Frames
(ANCF) based on the noisy pixels intensity among the frames. The
number of consecutive frames is adaptively calculated for each
region in image and its value may change from one region to another
region depending on the pixels intensity within the region. The
weights are determined by a well-defined mathematical criterion,
which is adaptive to the feature of spatiotemporal pixels of the
consecutive frames. It is experimentally shown that the proposed
filter can preserve image structures and edges under motion while
suppressing noise, and thus can be effectively used in image
sequences filtering. In addition, the AWA filter using ANCF is
particularly well suited for filtering sequences that contain segments
with abruptly changing scene content due to, for example, rapid
zooming and changes in the view of the camera.
Abstract: Incremental forming is a complex forming process with
continuously local cumulative deformation taking place during its
process, and springback that forming quality affected by would occur.
The springback evaluation method based on forming error
compensation also was proposed, which it can be defined as the
difference between theory and the actual amount of compensation
along the measured direction. According to forming error
compensation evaluation method, experiments was designed and
implemented. And from the results that obtained it can be show, the
magnitude of springback average (δE) of formed parts was very small,
and the forming precision could be significantly improved by adopting
compensation method. Based on double tensile stress state in the main
deformation area, a hypothesis that there is little springback be arisen
by bending behavior on the formed parts that was proposed.
Abstract: This paper presents a systematic approach for
designing Static Synchronous Series Compensator (SSSC) based
supplementary damping controllers for damping low frequency
oscillations in a single-machine infinite-bus power system. The
design problem of the proposed controller is formulated as an
optimization problem and RCGA is employed to search for optimal
controller parameters. By minimizing the time-domain based
objective function, in which the deviation in the oscillatory rotor
speed of the generator is involved; stability performance of the
system is improved. Simulation results are presented and compared
with a conventional method of tuning the damping controller
parameters to show the effectiveness and robustness of the proposed
design approach.
Abstract: The aim of the study was to identify seat belt wearing
factor among road users in Malaysia. Evidence-based approach
through in-depth crash investigation was utilised to determine the
intended objectives. The objective was scoped into crashes
investigated by Malaysian Institute of Road Safety Research
(MIROS) involving passenger vehicles within 2007 and 2010. Crash
information of a total of 99 crash cases involving 240 vehicles and
864 occupants were obtained during the study period. Statistical test
and logistic regression analysis have been performed. Results of the
analysis revealed that gender, seat position and age were associated
with seat belt wearing compliance in Malaysia. Males are 97.6%
more likely to wear seat belt compared to females (95% CI 1.317 to
2.964). By seat position, the finding indicates that frontal occupants
were 82 times more likely to be wearing seat belt (95% CI 30.199 to
225.342) as compared to rear occupants. It is also important to note
that the odds of seat belt wearing increased by about 2.64% (95% CI
1.0176 to 1.0353) for every one year increase in age. This study is
essential in understanding the Malaysian tendency in belting up
while being occupied in a vehicle. The factors highlighted in this
study should be emphasized in road safety education in order to
increase seat belt wearing rate in this country and ultimately in
preventing deaths due to road crashes.
Abstract: Most electrical distribution systems are incurring large
losses as the loads are wide spread, inadequate reactive power
compensation facilities and their improper control. A typical static
VAR compensator consists of capacitor bank in binary sequential
steps operated in conjunction with a thyristor controlled reactor of the
smallest step size. This SVC facilitates stepless control of reactive
power closely matching with load requirements so as to maintain
power factor nearer to unity. This type of SVC-s requiring a
appropriately controlled TCR. This paper deals with an air cored
reactor suitable for distribution transformer of 3phase, 50Hz, Dy11,
11KV/433V, 125 KVA capacity. Air cored reactors are designed,
built, tested and operated in conjunction with capacitor bank in five
binary sequential steps. It is established how the delta connected TCR
minimizes the harmonic components and the operating range for
various electrical quantities as a function of firing angle is
investigated. In particular firing angle v/s line & phase currents, D.C.
components, THD-s, active and reactive powers, odd and even triplen
harmonics, dominant characteristic harmonics are all investigated and
range of firing angle is fixed for satisfactory operation. The harmonic
spectra for phase and line quantities at specified firing angles are
given. In case the TCR is operated within the bound specified in this
paper established through simulation studies are yielding the best
possible operating condition particularly free from all dominant
harmonics.
Abstract: Installation of power compensation equipment in
some cases places additional buses into the system. Therefore, a total
number of power flow equations and voltage unknowns increase due
to additional locations of installed devices. In this circumstance, power flow calculation is more complicated. It may result in a
computational convergence problem. This paper presents a power flow calculation by using Newton-Raphson iterative method together
with the proposed load transfer technique. This concept is to eliminate additional buses by transferring installed loads at the new buses to existing two adjacent buses. Thus, the total number of power
flow equations is not changed. The overall computational speed is
expectedly shorter than that of solving the problem without applying the load transfer technique. A 15-bus test system is employed for test
to evaluate the effectiveness of the proposed load transfer technique. As a result, the total number of iteration required and execution time
is significantly reduced.
Abstract: In this paper, a new developed construction model of
the UPFC is proposed. The construction of this model consists of one
shunt compensation block and two series compensation blocks. In
this case, the UPFC with the new construction model will be
investigated when it is installed in multi-machine systems with nonlinear
load model. In addition, the steady–state performance of the
new model operating as impedance compensation will be presented
and compared with that obtained from the system without
compensation.