Abstract: Inter-symbol interference if not taken care off may cause severe error at the receiver and the detection of signal becomes difficult. An adaptive equalizer employing Recursive Least Squares algorithm can be a good compensation for the ISI problem. In this paper performance of communication link in presence of Least Mean Square and Recursive Least Squares equalizer algorithm is analyzed. A Model of communication system having Quadrature amplitude modulation and Rician fading channel is implemented using MATLAB communication block set. Bit error rate and number of errors is evaluated for RLS and LMS equalizer algorithm, due to change in Signal to Noise Ratio (SNR) and fading component gain in Rician fading Channel.
Abstract: This paper presents two simplified models to
determine nodal voltages in power distribution networks. These
models allow estimating the impact of the installation of reactive
power compensations equipments like fixed or switched capacitor
banks. The procedure used to develop the models is similar to the
procedure used to develop linear power flow models of transmission
lines, which have been widely used in optimization problems of
operation planning and system expansion. The steady state non-linear
load flow equations are approximated by linear equations relating the
voltage amplitude and currents. The approximations of the linear
equations are based on the high relationship between line resistance
and line reactance (ratio R/X), which is valid for power distribution
networks. The performance and accuracy of the models are evaluated
through comparisons with the exact results obtained from the
solution of the load flow using two test networks: a hypothetical
network with 23 nodes and a real network with 217 nodes.
Abstract: A 10bit, 40 MSps, sample and hold, implemented in 0.18-μm CMOS technology with 3.3V supply, is presented for application in the front-end stage of an analog-to-digital converter. Topology selection, biasing, compensation and common mode feedback are discussed. Cascode technique has been used to increase the dc gain. The proposed opamp provides 149MHz unity-gain bandwidth (wu), 80 degree phase margin and a differential peak to peak output swing more than 2.5v. The circuit has 55db Total Harmonic Distortion (THD), using the improved fully differential two stage operational amplifier of 91.7dB gain. The power dissipation of the designed sample and hold is 4.7mw. The designed system demonstrates relatively suitable response in different process, temperature and supply corners (PVT corners).
Abstract: In order to perform on-line measuring and detection
of PD signals, a total solution composing of an HFCT, A/D
converter and a complete software package is proposed. The
software package includes compensation of HFCT contribution,
filtering and noise reduction using wavelet transform and soft
calibration routines. The results have shown good performance and
high accuracy.
Abstract: Detection and tracking of the lip contour is an important
issue in speechreading. While there are solutions for lip tracking
once a good contour initialization in the first frame is available,
the problem of finding such a good initialization is not yet solved
automatically, but done manually. We have developed a new tracking
solution for lip contour detection using only few landmarks (15
to 25) and applying the well known Active Shape Models (ASM).
The proposed method is a new LMS-like adaptive scheme based on
an Auto regressive (AR) model that has been fit on the landmark
variations in successive video frames. Moreover, we propose an extra
motion compensation model to address more general cases in lip
tracking. Computer simulations demonstrate a fair match between
the true and the estimated spatial pixels. Significant improvements
related to the well known LMS approach has been obtained via a
defined Frobenius norm index.
Abstract: This paper proposed a nonlinear model predictive
control (MPC) method for the control of gantry crane. One of the main
motivations to apply MPC to control gantry crane is based on its
ability to handle control constraints for multivariable systems. A
pre-compensator is constructed to compensate the input nonlinearity
(nonsymmetric dead zone with saturation) by using its inverse
function. By well tuning the weighting function matrices, the control
system can properly compromise the control between crane position
and swing angle. The proposed control algorithm was implemented for
the control of gantry crane system in System Control Lab of University
of Technology, Sydney (UTS), and achieved desired experimental
results.
Abstract: In recent years the large scale use of the power electronic equipment has led to an increase of harmonics in the power system. The harmonics results into a poor power quality and have great adverse economical impact on the utilities and customers. Current harmonics are one of the most common power quality problems and are usually resolved by using shunt active filter (SHAF). The main objective of this work is to develop PI and Fuzzy logic controllers (FLC) to analyze the performance of Shunt Active Filter for mitigating current harmonics under balanced and unbalanced sinusoidal source voltage conditions for normal load and increased load. When the supply voltages are ideal (balanced), both PI and FLC are converging to the same compensation characteristics. However, the supply voltages are non-ideal (unbalanced), FLC offers outstanding results. Simulation results validate the superiority of FLC with triangular membership function over the PI controller.
Abstract: In this paper, the data correction algorithm is suggested
when the environmental air temperature varies. To correct the infrared
data in this paper, the initial temperature or the initial infrared image
data is used so that a target source system may not be necessary. The
temperature data obtained from infrared detector show nonlinear
property depending on the surface temperature. In order to handle this
nonlinear property, Taylor series approach is adopted. It is shown that
the proposed algorithm can reduce the influence of environmental
temperature on the components in the board. The main advantage of
this algorithm is to use only the initial temperature of the components
on the board rather than using other reference device such as black
body sources in order to get reference temperatures.
Abstract: In this paper we consider the problem of change
detection and non stationary signals tracking. Using parametric
estimation of signals based on least square lattice adaptive filters we
consider for change detection statistical parametric methods using
likelihood ratio and hypothesis tests. In order to track signals
dynamics, we introduce a compensation procedure in the adaptive
estimation. This will improve the adaptive estimation performances
and fasten it-s convergence after changes detection.
Abstract: Resistance spot welding process comprises of electric,
thermal and mechanical phenomenon, which makes this process
complex and highly non-linear and thus, it becomes difficult to model
it. In order to obtain good weld nugget during spot welding, hit and
trial welds are usually done which is very costly. Therefore the
numerical simulation research has been conducted to understand the
whole process. In this paper three different cases were analyzed by
varying the tip contact area and it was observed that, with the
variation of tip contact area the nugget formation at the faying
surface is affected. The tip contact area of the welding electrode
becomes large with long welding cycles. Therefore in order to
maintain consistency of nugget formation during the welding process,
the current compensation in control feedback is required. If the
contact area of the welding electrode tip is reduced, a large amount of
current flows through the faying surface, as a result of which
sputtering occurs.
Abstract: A research effort to find the reality of the business of Japan-s software globalization of enterprise-level business software systems has found that while the number of Japan-made enterpriselevel software systems is comparable with those of the other G7 countries, the business is limited to the East and Southeast Asian markets. This indicates that this business has a problem in the European and USA markets. Based on the knowledge that the research has established, the research concludes that the communication problems arise from the lack of individualists' communication styles and foreign language skills in Japan's software globalization is compensated by similarities in certain Japanese cultural factors and Japan's cultural power in the East and Southeast Asian markets and that this business does not have this compensation factor in the European and American markets due to dissimilarities and no cultural power.
Abstract: Since straightness error of linear motor stage is hardly
dependent upon machining accuracy and assembling accuracy, there is
limit on maximum realizable accuracy. To cope with this limitation,
this paper proposed a servo system to compensate straightness error of
a linear motor stage. The servo system is mounted on the slider of the
linear motor stage and moves in the direction of the straightness error
so as to compensate the error. From position dependency and
repeatability of the straightness error of the slider, a feedforward
compensation control is applied to the platform servo control. In the
consideration of required fine positioning accuracy, a platform driven
by an electro-magnetic actuator is suggested and a sliding mode
control was applied. The effectiveness of the sliding mode control was
verified along with some experimental results.
Abstract: The so-called all-pass filter circuits are commonly
used in the field of signal processing, control and measurement.
Being connected to capacitive loads, these circuits tend to loose their
stability; therefore the elaborate analysis of their dynamic behavior is
necessary. The compensation methods intending to increase the
stability of such circuits are discussed in this paper, including the socalled
lead-lag compensation technique being treated in detail. For
the dynamic modeling, a two-port network model of the all-pass filter
is being derived. The results of the model analysis show, that
effective lead-lag compensation can be achieved, alone by the
optimization of the circuit parameters; therefore the application of
additional electric components are not needed to fulfill the stability
requirement.
Abstract: Medical negligence disputes in Malaysia are mainly resolved through litigation by using the tort system. The tort system, being adversarial in nature has subjected parties to litigation hazards such as delay, excessive costs and uncertainty of outcome. The dissatisfaction of the tort system in compensating medically injured victims has created various alternatives to litigation. Amongst them is the implementation of a no-fault compensation system which would allow compensation to be given without the need of proving fault on the medical personnel. Instead, the community now bears the burden of compensating and at the end, promotes collective responsibility. For Malaysia, introducing a no-fault system would provide a tempting solution and may ultimately, achieve justice for the medical injured victims. Nevertheless, such drastic change requires a great deal of consideration to determine the suitability of the system and whether or not it will eventually cater for the needs of the Malaysian population
Abstract: The evolution of technology and construction techniques has enabled the upgrading of transport networks. In particular, the high-speed rail networks allow convoys to peak at above 300 km/h. These structures, however, often significantly impact the surrounding environment. Among the effects of greater importance are the ones provoked by the soundwave connected to train transit. The wave propagation affects the quality of life in areas surrounding the tracks, often for several hundred metres. There are substantial damages to properties (buildings and land), in terms of market depreciation. The present study, integrating expertise in acoustics, computering and evaluation fields, outlines a useful model to select project paths so as to minimize the noise impact and reduce the causes of possible litigation. It also facilitates the rational selection of initiatives to contain the environmental damage to the already existing railway tracks. The research is developed with reference to the Italian regulatory framework (usually more stringent than European and international standards) and refers to a case study concerning the high speed network in Italy.
Abstract: This paper present a new method for design of power
system stabilizer (PSS) based on sliding mode control (SMC)
technique. The control objective is to enhance stability and improve
the dynamic response of the multi-machine power system. In order to
test effectiveness of the proposed scheme, simulation will be carried
out to analyze the small signal stability characteristics of the system
about the steady state operating condition following the change in
reference mechanical torque and also parameters uncertainties. For
comparison, simulation of a conventional control PSS (lead-lag
compensation type) will be carried out. The main approach is
focusing on the control performance which later proven to have the
degree of shorter reaching time and lower spike.
Abstract: In this paper, a new reversible watermarking method is presented that reduces the size of a stereoscopic image sequence while keeping its content visible. The proposed technique embeds the residuals of the right frames to the corresponding frames of the left sequence, halving the total capacity. The residual frames may result in after a disparity compensated procedure between the two video streams or by a joint motion and disparity compensation. The residuals are usually lossy compressed before embedding because of the limited embedding capacity of the left frames. The watermarked frames are visible at a high quality and at any instant the stereoscopic video may be recovered by an inverse process. In fact, the left frames may be exactly recovered whereas the right ones are slightly distorted as the residuals are not embedded intact. The employed embedding method reorders the left frame into an array of consecutive pixel pairs and embeds a number of bits according to their intensity difference. In this way, it hides a number of bits in intensity smooth areas and most of the data in textured areas where resulting distortions are less visible. The experimental evaluation demonstrates that the proposed scheme is quite effective.
Abstract: A fully on-chip low drop-out (LDO) voltage regulator with 100pF output load capacitor is presented. A novel frequency compensation scheme using current buffer is adopted to realize single dominant pole within the unit gain frequency of the regulation loop, the phase margin (PM) is at least 50 degree under the full range of the load current, and the power supply rejection (PSR) character is improved compared with conventional Miller compensation. Besides, the differentiator provides a high speed path during the load current transient. Implemented in 0.18μm CMOS technology, the LDO voltage regulator provides 100mA load current with a stable 1.8V output voltage consuming 80μA quiescent current.
Abstract: In order to improve control performance and eliminate steady, a coupling compensation for 6-DOF parallel robot is presented. Taking dynamic load Tank Simulator as the research object, this paper analyzes the coupling of 6-DOC parallel robot considering the degree of freedom of the 6-DOF parallel manipulator. The coupling angle and coupling velocity are derived based on inverse kinematics model. It uses the mechanism-model combined method which takes practical moving track that considering the performance of motion controller and motor as its input to make the study. Experimental results show that the coupling compensation improves motion stability as well as accuracy. Besides, it decreases the dither amplitude of dynamic load Tank Simulator.
Abstract: Compensating physiological motion in the context
of minimally invasive cardiac surgery has become an attractive
issue since it outperforms traditional cardiac procedures offering
remarkable benefits. Owing to space restrictions, computer vision
techniques have proven to be the most practical and suitable solution.
However, the lack of robustness and efficiency of existing methods
make physiological motion compensation an open and challenging
problem. This work focusses on increasing robustness and efficiency
via exploration of the classes of 1−and 2−regularized optimization,
emphasizing the use of explicit regularization. Both approaches are
based on natural features of the heart using intensity information.
Results pointed out the 1−regularized optimization class as the best
since it offered the shortest computational cost, the smallest average
error and it proved to work even under complex deformations.