Abstract: An interesting method to produce calcium carbonate is based in a gas-liquid reaction between carbon dioxide and aqueous solutions of calcium hydroxide. The design parameters for gas-liquid phase are flow regime, individual mass transfer, gas-liquid specific interfacial area. Most studies on gas-liquid phase were devoted to the experimental determination of some of these parameters, and more specifically, of the mass transfer coefficient, kLa which depends fundamentally on the superficial gas velocity and on the physical properties of absorption phase. The principle investigation was directed to study the effect of the vibration on the mass transfer coefficient kLa in gas-liquid phase during absorption of CO2 in the in aqueous solution of calcium hydroxide. The vibration with a higher frequency increase the mass transfer coefficient kLa, but vibration with lower frequency didn-t improve it, the mass transfer coefficient kLa increase with increase the superficial gas velocity.
Abstract: Air pollution is a major environmental health
problem, affecting developed and developing countries around the
world. Increasing amounts of potentially harmful gases and
particulate matter are being emitted into the atmosphere on a global
scale, resulting in damage to human health and the environment.
Petroleum-related air pollutants can have a wide variety of adverse
environmental impacts. In the crude oil production sectors, there is a
strong need for a thorough knowledge of gaseous emissions resulting
from the flaring of associated gas of known composition on daily
basis through combustion activities under several operating
conditions. This can help in the control of gaseous emission from
flares and thus in the protection of their immediate and distant
surrounding against environmental degradation.
The impacts of methane and non-methane hydrocarbons emissions
from flaring activities at oil production facilities at Kuwait Oilfields
have been assessed through a screening study using records of flaring
operations taken at the gas and oil production sites, and by analyzing
available meteorological and air quality data measured at stations
located near anthropogenic sources. In the present study the
Industrial Source Complex (ISCST3) Dispersion Model is used to
calculate the ground level concentrations of methane and nonmethane
hydrocarbons emitted due to flaring in all over Kuwait
Oilfields.
The simulation of real hourly air quality in and around oil
production facilities in the State of Kuwait for the year 2006,
inserting the respective source emission data into the ISCST3
software indicates that the levels of non-methane hydrocarbons from
the flaring activities exceed the allowable ambient air standard set by
Kuwait EPA. So, there is a strong need to address this acute problem
to minimize the impact of methane and non-methane hydrocarbons
released from flaring activities over the urban area of Kuwait.
Abstract: This article presents the simulation, parameterization and optimization of an electromagnet with the C–shaped configuration, intended for the study of magnetic properties of materials. The electromagnet studied consists of a C-shaped yoke, which provides self–shielding for minimizing losses of magnetic flux density, two poles of high magnetic permeability and power coils wound on the poles. The main physical variable studied was the static magnetic flux density in a column within the gap between the poles, with 4cm2 of square cross section and a length of 5cm, seeking a suitable set of parameters that allow us to achieve a uniform magnetic flux density of 1x104 Gaussor values above this in the column, when the system operates at room temperature and with a current consumption not exceeding 5A. By means of a magnetostatic analysis by the finite element method, the magnetic flux density and the distribution of the magnetic field lines were visualized and quantified. From the results obtained by simulating an initial configuration of electromagnet, a structural optimization of the geometry of the adjustable caps for the ends of the poles was performed. The magnetic permeability effect of the soft magnetic materials used in the poles system, such as low– carbon steel (0.08% C), Permalloy (45% Ni, 54.7% Fe) and Mumetal (21.2% Fe, 78.5% Ni), was also evaluated. The intensity and uniformity of the magnetic field in the gap showed a high dependence with the factors described above. The magnetic field achieved in the column was uniform and its magnitude ranged between 1.5x104 Gauss and 1.9x104 Gauss according to the material of the pole used, with the possibility of increasing the magnetic field by choosing a suitable geometry of the cap, introducing a cooling system for the coils and adjusting the spacing between the poles. This makes the device a versatile and scalable tool to generate the magnetic field necessary to perform magnetic characterization of materials by techniques such as vibrating sample magnetometry (VSM), Hall-effect, Kerr-effect magnetometry, among others. Additionally, a CAD design of the modules of the electromagnet is presented in order to facilitate the construction and scaling of the physical device.
Abstract: Performance of a cobalt doped sol-gel derived silica (Co/SiO2) catalyst for Fischer–Tropsch synthesis (FTS) in slurryphase reactor was studied using paraffin wax as initial liquid media. The reactive mixed gas, hydrogen (H2) and carbon monoxide (CO) in a molar ratio of 2:1, was flowed at 50 ml/min. Braunauer-Emmett- Teller (BET) surface area and X-ray diffraction (XRD) techniques were employed to characterize both the specific surface area and crystallinity of the catalyst, respectively. The reduction behavior of Co/SiO2 catalyst was investigated using the Temperature Programmmed Reduction (TPR) method. Operating temperatures were varied from 493 to 533K to find the optimum conditions to maximize liquid fuels production, gasoline and diesel.
Abstract: Rapid urbanization, industrialization and population
growth have led to an increase in number of automobiles that cause
air pollution. It is estimated that road traffic contributes 60% of air
pollution in urban areas. A case by case assessment is required to
predict the air quality in urban situations, so as to evolve certain
traffic management measures to maintain the air quality levels with
in the tolerable limits. Calicut city in the state of Kerala, India has
been chosen as the study area. Carbon Monoxide (CO) concentration
was monitored at 15 links in Calicut city and air quality performance
was evaluated over each link. The CO pollutant concentration values
were compared with the National Ambient Air Quality Standards
(NAAQS), and the CO values were predicted by using CALINE4 and
IITLS and Linear regression models. The study has revealed that
linear regression model performs better than the CALINE4 and
IITLS models. The possible association between CO pollutant
concentration and traffic parameters like traffic flow, type of vehicle,
and traffic stream speed was also evaluated.
Abstract: Pharmaceutical industries and effluents of sewage treatment plants are the main sources of residual pharmaceuticals in water resources. These emergent pollutants may adversely impact the biophysical environment. Pharmaceutical industries often generate wastewater that changes in characteristics and quantity depending on the used manufacturing processes. Carbamazepine (CBZ), {5Hdibenzo [b,f]azepine-5-carboxamide, (C15H12N2O)}, is a significant non-biodegradable pharmaceutical contaminant in the Jordanian pharmaceutical wastewater, which is not removed by the activated sludge processes in treatment plants. Activated carbon may potentially remove that pollutant from effluents, but the high cost involved suggests that more attention should be given to the potential use of low-cost materials in order to reduce cost and environmental contamination. Powders of Jordanian non-metallic raw materials namely, Azraq Bentonite (AB), Kaolinite (K), and Zeolite (Zeo) were activated (acid and thermal treatment) and evaluated by removing CBZ. The results of batch and column techniques experiments showed around 46% and 67% removal of CBZ respectively.
Abstract: In the Enhanced Oil Recovery (EOR) method, use of Carbon dioxide flooding whereby CO2 is injected into an oil reservoir to increase output when extracting oil resulted significant recovery worldwide. The carbon dioxide function as a pressurizing agent when mixed into the underground crude oil will reduce its viscosity and will enable a rapid oil flow. Despite the CO2’s advantage in the oil recovery, it may result to asphaltene precipitation a problem that will cause the reduction of oil produced from oil wells. In severe cases, asphaltene precipitation can cause costly blockages in oil pipes and machinery. This paper presents reviews of several studies done on mathematical modeling of asphaltene precipitation. The synthesized result from several researches done on this topic can be used as guide in order to better understand asphaltene precipitation. Likewise, this can be used as initial reference for students, and new researchers doing study on asphaltene precipitation.
Abstract: In the present work we report a gram negative
bacterial isolate, from soil of a dye industry, with promising
biorefining and bioremediation potential. This isolate (GBS.5) could
utilize carbazole (nitrogen containing polycyclic aromatic
hydrocarbon) as the sole source of nitrogen and carbon and utilize
almost 98% of 3mM carbazole in 100 hours. The specific activity of
our GBS.5 isolate for carbazole degradation at 30°C and pH 7.0 was
found to be 11.36 μmol/min/g dry cell weight as compared to 10.4
μmol/min/g dry cell weight, the highest reported specific activity till
date. The presence of car genes (the genes involved in
denitrogenation of carbazole) was confirmed through PCR
amplification.
Abstract: The use of renewable energy sources becomes more
necessary and interesting. As wider applications of renewable energy
devices at domestic, commercial and industrial levels has not only
resulted in greater awareness, but also significantly installed
capacities. In addition, biomass principally is in the form of woods,
which is a form of energy by humans for a long time. Gasification is
a process of conversion of solid carbonaceous fuel into combustible
gas by partial combustion. Many gasifier models have various
operating conditions; the parameters kept in each model are different.
This study applied experimental data, which has three inputs, which
are; biomass consumption, temperature at combustion zone and ash
discharge rate. One output is gas flow rate. For this paper, neural
network was used to identify the gasifier system suitable for the
experimental data. In the result,neural networkis usable to attain the
answer.
Abstract: Xanthan gum is a microbial polysaccharide of great
commercial significance. The purpose of this study was to select the
optimum fermentation time for xanthan gum production by
Xanthomonas campestris (NRRL-B-1459) using 10% sugar beet
molasses as a carbon source. The pre-heating of sugar beet molasses
and the supplementation of the medium were investigated in order to
improve xanthan gum production. Maximum xanthan gum
production in fermentation media (9.02 g/l) was observed after 4 days
shaking incubation at 25°C and 240 rpm agitation speed. A solution
of 10% sucrose was used as a control medium. Results indicated that
the optimum period for xanthan gum production in this condition was
4 days.
Abstract: In this investigation Salicylic acid, Sulfosalicylic acid
and Acetyl salicylic acid were chosen as a sample for thin layer
chromatography (TLC) on silica gel plates. Bicarbonate buffer at
different pH containing different amounts of boric acid was applied
as mobile phase. Specific interaction of these substances with boric
acid has effect on Rf in thin layer chromatography. Regular and
similar trend was observed in variations of Rf for mentioned
compounds in TLC by altering of percentages of boric acid in mobile
phase in pH range of 8-10. Also effect of organic solvent, mixture of
water/ organic solvent and organic solvent containing boric acid as
mobile phase was studied.
Abstract: In July 2012, an indoor/outdoor monitoring
programme was undertaken in two university sports facilities: a
fronton and a gymnasium. Comfort parameters (temperature, relative
humidity, CO and CO2) and total volatile organic compounds
(VOCs) were continuously monitored. Concentrations of NO2,
carbonyl compounds and individual VOCs were obtained. Low
volume samplers were used to collect particulate matter (PM10). The
minimum ventilation rates stipulated for acceptable indoor air quality
were observed in both sports facilities. It was found that cleaning
activities may have a large influence on the VOC levels. Acrolein
was one of the most abundant carbonyl compounds, showing
concentrations above the recommended limit. Formaldehyde was
detected at levels lower than those commonly reported for other
indoor environments. The PM10 concentrations obtained during the
occupancy periods ranged between 38 and 43μgm-3 in the fronton and
from 154 to 198μgm-3 in the gymnasium.
Abstract: Rice husk is one of the alternative fuels for Thailand because of its high potential and environmental benefits. Nonetheless, the environmental profile of the electricity production from rice husk must be assessed to ensure reduced environmental damage. A 10 MW pilot plant using rice husk as feedstock is the study site. The environmental impacts from rice husk power plant are evaluated by using the Life Cycle Assessment (LCA) methodology. Energy, material and carbon balances have been determined for tracing the system flow. Carbon closure has been used for describing of the net amount of CO2 released from the system in relation to the amount being recycled between the power plant and the CO2 adsorbed by rice husk. The transportation of rice husk to the power plant has significant on global warming, but not on acidification and photo-oxidant formation. The results showed that the impact potentials from rice husk power plant are lesser than the conventional plants for most of the categories considered; except the photo-oxidant formation potential from CO. The high CO from rice husk power plant may be due to low boiler efficiency and high moisture content in rice husk. The performance of the study site can be enhanced by improving the combustion efficiency.
Abstract: Chemically defined Schlegel-s medium was modified
to improve production of cell growth and other metabolites that are
produced by fluorescent pseudomonad R62 strain. The modified
medium does not require pH control as pH changes are kept within ±
0.2 units of the initial pH 7.1 during fermentation. The siderophore
production was optimized for the fluorescent pseudomonad strain in
the modified medium containing 1% glycerol as a major carbon
source supplemented with 0.05% succinic acid and 0.5% Ltryptophan.
Indole-3 acetic acid (IAA) production was higher when
L-tryptophan was used at 0.5%. The 2,4- diacetylphloroglucinol
(DAPG) was higher with amended three trace elements in medium.
The optimized medium produced 2.28 g/l of dry cell mass and 900
mg/l of siderophore at the end of 36 h cultivation, while the
production levels of IAA and DAPG were 65 mg/l and 81 mg/l
respectively at the end of 48 h cultivation.
Abstract: In this investigation, types of commercial and special
polyacrylonitrile (PAN) fibers contain sodium 2-methyl-2-
acrylamidopropane sulfonate (SAMPS) and itaconic acid (IA)
comonomers were studied by fourier transform infrared (FT-IR)
spectroscopy. The study of FT-IR spectra of PAN fibers samples
with different comonomers shows that during stabilization of PAN
fibers, the peaks related to C≡N bonds and CH2 are reduced sharply.
These reductions are related to cyclization of nitrile groups and
stabilization procedure. This reduction in PAN fibers contain IA
comonomer is very intense in comparison with PAN fibers contain
SAMPS comonomer. This fact indicates the cycling and stabilization
for sample contain IA comonomer have been conducted more
completely. Therefore the carbon fibers produced from this material
have higher tensile strength due to suitable stabilization.
Abstract: Heat powered solid sorption is a feasible alternative to
electrical vapor compression refrigeration systems. In this paper,
activated carbon (powder type Maxsorb and fiber type ACF-A10)-
CO2 based adsorption cooling cycles are studied using the pressuretemperature-
concentration (P-T-W) diagram. The specific cooling
effect (SCE) and the coefficient of performance (COP) of these two
cooling systems are simulated for the driving heat source
temperatures ranging from 30 ºC to 90 ºC in terms of different
cooling load temperatures with a cooling source temperature of 25
ºC. It is found from the present analysis that Maxsorb-CO2 couple
shows higher cooling capacity and COP. The maximum COPs of
Maxsorb-CO2 and ACF(A10)-CO2 based cooling systems are found
to be 0.15 and 0.083, respectively. The main innovative feature of
this cooling cycle is the ability to utilize low temperature waste heat
or solar energy using CO2 as the refrigerant, which is one of the best
alternative for applications where flammability and toxicity are not
allowed.
Abstract: In this research, an aerobic composting method is
studied to reuse organic waste from rubber factory waste as soil fertilizer and to study the effect of cellulolytic microbial activator
(CMA) as the activator in the rubber factory waste composting. The
performance of the composting process was monitored as a function
of carbon and organic matter decomposition rate, temperature and
moisture content. The results indicate that the rubber factory waste is best composted with water hyacinth and sludge than composted
alone. In addition, the CMA is more affective when mixed with the rubber factory waste, water hyacinth and sludge since a good fertilizer is achieved. When adding CMA into the rubber factory
waste composted alone, the finished product does not achieve a
standard of fertilizer, especially the C/N ratio.
Finally, the finished products of composting rubber factory waste and water hyacinth and sludge (both CMA and without CMA), can be an environmental friendly alternative to solve the disposal problems of rubber factory waste. Since the C/N ratio, pH, moisture
content, temperature, and nutrients of the finished products are acceptable for agriculture use.
Abstract: A new composite sorbent based on carbonized rice
husk (CRH) and immobilized on it living cells and inactivated
cultural liquid containing antimicrobials metabolites of Bacillus
subtilis CK-245 is developed. The sorption and antimicrobic activity
of CRH concerning five species of Enterobacteriaceae is studied.
Prospects of use of developed sorbent in medicine and veterinary
science is shown.
Abstract: In this study we investigate the insertion of
pioglitazone, a Thiazolidinedione, into the two different sizes of
Carbon nanotub. It was shown that the insertion of pioglitazone into
the carbon nanotube in a water solute environment could be related
to the diameter of the nanotube and in the flow of the waters via
hydrophilic interactions. This encapsulated drug-carbon nanotube
molecule can be further applicable in other investigations in target
therapy with these agents regarding to reduce their potential toxic
effects.
Abstract: A concrete structure is designed and constructed for its
purpose of use, and is expected to maintain its function for the target
durable years from when it was planned. Nevertheless, as time elapses
the structure gradually deteriorates and then eventually degrades to the
point where the structure cannot exert the function for which it was
planned. The performance of concrete that is able to maintain the level
of the performance required over the designed period of use as it has
less deterioration caused by the elapse of time under the designed
condition is referred to as Durability. There are a number of causes of
durability degradation, but especially chloride damage, carbonation,
freeze-thaw, etc are the main causes. In this study, carbonation, one of
the main causes of deterioration of the durability of a concrete
structure, was investigated via a microstructure analysis technique.
The method for the measurement of carbonation was studied using the
existing indicator method, and the method of measuring the progress
of carbonation in a quantitative manner was simultaneously studied
using a FT-IR (Fourier-Transform Infrared) Spectrometer along with
the microstructure analysis technique.