Abstract: A sequential treatment of ozonation followed by a
Fenton or photo-Fenton process, using black light lamps (365 nm) in
this latter case, has been applied to remove a mixture of
pharmaceutical compounds and the generated by-products both in
ultrapure and secondary treated wastewater. The scientifictechnological
innovation of this study stems from the in situ
generation of hydrogen peroxide from the direct ozonation of
pharmaceuticals, and can later be used in the application of Fenton
and photo-Fenton processes. The compounds selected as models
were sulfamethoxazol and acetaminophen. It should be remarked that
the use of a second process is necessary as a result of the low
mineralization yield reached by the exclusive application of ozone.
Therefore, the influence of the water matrix has been studied in terms
of hydrogen peroxide concentration, individual compound
concentration and total organic carbon removed. Moreover, the
concentration of different iron species in solution has been measured.
Abstract: A kinetic model for propane dehydrogenation in an
industrial moving bed reactor is developed based on the reported
reaction scheme. The kinetic parameters and activity constant are
fine tuned with several sets of balanced plant data. Plant data at
different operating conditions is applied to validate the model and
the results show a good agreement between the model
predictions and plant observations in terms of the amount of main
product, propylene produced. The simulation analysis of key
variables such as inlet temperature of each reactor (Tinrx) and
hydrogen to total hydrocarbon ratio (H2/THC) affecting process
performance is performed to identify the operating condition to
maximize the production of propylene. Within the range of operating
conditions applied in the present studies, the operating condition to
maximize the propylene production at the same weighted average
inlet temperature (WAIT) is ΔTinrx1= -2, ΔTinrx2= +1, ΔTinrx3= +1 ,
ΔTinrx4= +2 and ΔH2/THC= -0.02. Under this condition, the surplus
propylene produced is 7.07 tons/day as compared with base case.
Abstract: The dominant judgment for earthquake damaged reinforced concrete (RC) structures is to rebuild them with the new ones. Consequently, this paper estimates if there is chance to repair earthquake RC beams and obtain economical contribution to modern day society. Therefore, the totally damaged (damaged in shear under cyclic load) reinforced concrete (RC) beams repaired and strengthened by externally bonded carbon fibre reinforced polymer (CFRP) strips in this study. Four specimens, apart from the reference beam, were separated into two distinct groups. Two experimental beams in the first group primarily tested up to failure then appropriately repaired and strengthened with CFRP strips. Two undamaged specimens from the second group were not repaired but strengthened by the identical strengthening scheme as the first group for comparison. This study studies whether earthquake damaged RC beams that have been repaired and strengthened will validate similar strength and behavior to equally strengthened, undamaged RC beams. Accordingly, a strength correspondence according to strengthened specimens was acquired for the repaired and strengthened specimens. Test results confirmed that repair and strengthening, which were estimated in the experimental program, were effective for the specimens with the cracking patterns considered in the experimental program.
Abstract: In the present study, a steady-state simulation model
has been developed to evaluate the system performance of a
transcritical carbon dioxide heat pump system for simultaneous water
cooling and heating. Both the evaporator (including both two-phase
and superheated zone) and gas cooler models consider the highly
variable heat transfer characteristics of CO2 and pressure drop. The
numerical simulation model of transcritical CO2 heat pump has been
validated by test data obtained from experiments on the heat pump
prototype. Comparison between the test results and the model
prediction for system COP variation with compressor discharge
pressure shows a modest agreement with a maximum deviation of
15% and the trends are fairly similar. Comparison for other operating
parameters also shows fairly similar deviation between the test
results and the model prediction. Finally, the simulation results are
presented to study the effects of operating parameters such as,
temperature of heat exchanger fluid at the inlet, discharge pressure,
compressor speed on system performance of CO2 heat pump, suitable
in a dairy plant where simultaneous cooling at 4oC and heating at
73oC are required. Results show that good heat transfer properties of
CO2 for both two-phase and supercritical region and efficient
compression process contribute a lot for high system COPs.
Abstract: Using steelmaking slag as a raw material, aragonite superstructure product had been synthesized via an indirect CO2 mineral sequestration rout. It mainly involved two separate steps, in which the element of calcium is first selectively leached from steelmaking slag by a novel leaching media consisting of organic solvent Tributyl phosphate (TBP), acetic acid, and ultra-purity water, followed by enhanced carbonation in a separate step for aragonite superstructure production as well as efficiency recovery of leaching media. Based on the different leaching medium employed in the steelmaking slag leaching process, two typical products were collected from the enhanced carbonation step. The products were characterized by X-ray powder diffraction (XRD) and scanning electron microscopy (SEM), respectively. It reveals that the needle-like aragonite crystals self-organized into aragonite superstructure particles including aragonite microspheres as well as dumbbell-like spherical particles, can be obtained from the steelmaking slag with the purity over 99%.
Abstract: Solution for the complete removal of carbon
monoxide from the exhaust gases still poses a challenge to the
researchers and this problem is still under development. Modeling for
reduction of carbon monoxide is carried out using heterogeneous
reaction using low cost non-noble metal based catalysts for the
purpose of controlling emissions released to the atmosphere. A
simple one-dimensional model was developed for the monolith using
hopcalite catalyst. The converter is assumed to be an adiabatic
monolith operating under warm-up conditions. The effect of inlet gas
temperatures and catalyst loading on carbon monoxide reduction
during cold start period in the converter is analysed.
Abstract: Octree compression techniques have been used
for several years for compressing large three dimensional data
sets into homogeneous regions. This compression technique
is ideally suited to datasets which have similar values in
clusters. Oil engineers represent reservoirs as a three dimensional
grid where hydrocarbons occur naturally in clusters. This
research looks at the efficiency of storing these grids using
octree compression techniques where grid cells are broken
into active and inactive regions. Initial experiments yielded
high compression ratios as only active leaf nodes and their
ancestor, header nodes are stored as a bitstream to file on
disk. Savings in computational time and memory were possible
at decompression, as only active leaf nodes are sent to the
graphics card eliminating the need of reconstructing the original
matrix. This results in a more compact vertex table, which can
be loaded into the graphics card quicker and generating shorter
refresh delay times.
Abstract: In this study, effects of premixed and equivalence
ratios on CO and HC emissions of a dual fuel HCCI engine are
investigated. Tests were conducted on a single-cylinder engine with
compression ratio of 17.5. Premixed gasoline is provided by a
carburetor connected to intake manifold and equipped with a screw
to adjust premixed air-fuel ratio, and diesel fuel is injected directly
into the cylinder through an injector at pressure of 250 bars. A heater
placed at inlet manifold is used to control the intake charge
temperature. Optimal intake charge temperature results in better
HCCI combustion due to formation of a homogeneous mixture,
therefore, all tests were carried out over the optimum intake
temperature of 110-115 ºC. Timing of diesel fuel injection has a great
effect on stratification of in-cylinder charge and plays an important
role in HCCI combustion phasing. Experiments indicated 35 BTDC
as the optimum injection timing. Varying the coolant temperature in
a range of 40 to 70 ºC, better HCCI combustion was achieved at 50
ºC. Therefore, coolant temperature was maintained 50 ºC during all
tests. Simultaneous investigation of effective parameters on HCCI
combustion was conducted to determine optimum parameters
resulting in fast transition to HCCI combustion. One of the
advantages of the method studied in this study is feasibility of easy
and fast transition of typical diesel engine to a dual fuel HCCI
engine. Results show that increasing premixed ratio, while keeping
EGR rate constant, increases unburned hydrocarbon (UHC)
emissions due to quenching phenomena and trapping of premixed
fuel in crevices, but CO emission decreases due to increase in CO to
CO2 reactions.
Abstract: A diamond-like carbon (DLC) based solid-lubricant
film was designed and DLC films were successfully prepared using a
microwave plasma enhanced magnetron sputtering deposition
technology. Post-test characterizations including Raman
spectrometry, X-ray diffraction, nano-indentation test, adhesion test,
friction coefficient test were performed to study the influence of
substrate bias voltage on the mechanical properties of the W- and
S-doped DLC films. The results indicated that the W- and S-doped
DLC films also had the typical structure of DLC films and a better
mechanical performance achieved by the application of a substrate
bias of -200V.
Abstract: It is well recognized that the green house gases such
as Chlorofluoro Carbon (CFC), CH4, CO2 etc. are responsible
directly or indirectly for the increase in the average global temperature
of the Earth. The presence of CFC is responsible for
the depletion of ozone concentration in the atmosphere due to
which the heat accompanied with the sun rays are less absorbed
causing increase in the atmospheric temperature of the Earth. The
gases like CH4 and CO2 are also responsible for the increase in
the atmospheric temperature. The increase in the temperature level
directly or indirectly affects the dynamics of interacting species
systems. Therefore, in this paper a mathematical model is proposed
and analysed using stability theory to asses the effects of increasing
temperature due to greenhouse gases on the survival or extinction of
populations in a prey-predator system. A threshold value in terms
of a stress parameter is obtained which determines the extinction or
existence of populations in the underlying system.
Abstract: The remediation of water resources pollution in
developing countries requires the application of alternative
sustainable cheaper and efficient end-of-pipe wastewater treatment
technologies. The feasibility of use of South African cheap and
abundant pine tree (Pinus patula) sawdust for development of lowcost
AC of comparable quality to expensive commercial ACs in the
abatement of water pollution was investigated. AC was developed at
optimized two-stage N2-superheated steam activation conditions in a
fixed bed reactor, and characterized for proximate and ultimate
properties, N2-BET surface area, pore size distribution, SEM, pHPZC
and FTIR. The sawdust pyrolysis activation energy was evaluated by
TGA. Results indicated that the chars prepared at 800oC and 2hrs
were suitable for development of better quality AC at 800oC and 47%
burn-off having BET surface area (1086m2/g), micropore volume
(0.26cm3/g), and mesopore volume (0.43cm3/g) comparable to
expensive commercial ACs, and suitable for water contaminants
removal. The developed AC showed basic surface functionality at
pHPZC at 10.3, and a phenol adsorption capacity that was higher than
that of commercial Norit (RO 0.8) AC. Thus, it is feasible to develop
better quality low-cost AC from (Pinus patula) sawdust using twostage
N2-steam activation in fixed-bed reactor.
Abstract: A numerical study is presented on buckling and post
buckling behaviour of laminated carbon fiber reinforced plastic
(CFRP) thin-walled cylindrical shells under axial compression using
asymmetric meshing technique (AMT). Asymmetric meshing
technique is a perturbation technique to introduce disturbance without
changing geometry, boundary conditions or loading conditions.
Asymmetric meshing affects predicted buckling load, buckling mode
shape and post-buckling behaviour. Linear (eigenvalue) and nonlinear
(Riks) analyses have been performed to study the effect of
asymmetric meshing in the form of a patch on buckling behaviour.
The reduction in the buckling load using Asymmetric meshing
technique was observed to be about 15%. An isolated dimple formed
near the bifurcation point and the size of which increased to reach a
stable state in the post-buckling region. The load-displacement curve
behaviour applying asymmetric meshing is quite similar to the curve
obtained using initial geometric imperfection in the shell model.
Abstract: Carbon fibers are fabricated from different materials,
such as special polyacrylonitrile (PAN) fibers, rayon fibers and pitch.
Among these three groups of materials, PAN fibers are the most
widely used precursor for the manufacture of carbon fibers. The
process of fabrication carbon fibers from special PAN fibers includes
two steps; oxidative stabilization at low temperature and
carbonization at high temperatures in an inert atmosphere. Due to the
high price of raw materials (special PAN fibers), carbon fibers are
still expensive.
In the present work the main goal is making carbon fibers from
low price commercial PAN fibers with modified chemical
compositions. The results show that in case of conducting completes
stabilization process, it is possible to produce carbon fibers with
desirable tensile strength from this type of PAN fibers. To this
matter, thermal characteristics of commercial PAN fibers were
investigated and based upon the obtained results, with some changes
in conventional procedure of stabilization in terms of temperature
and time variables; the desirable conditions of complete stabilization
is achieved.
Abstract: The present work presents the extraction of copper(II)
from sulphuric acid solutions with Sodium diethyldithiocarbamate
(SDDT), and six different organic diluents: Dichloromethane,
Chloroform, Carbon tetrachloride, Toluene, xylene and Cyclohexane,
were tested. The pair SDDT/Chloroform showed to be the most
selective in removing the copper cations, and hence was considered
throughout the experimental study.
The effects of operating parameters such as the initial concentration
of the extracting agent, the agitation time, the agitation speed and the
acid concentration were considered.
For an initial concentration of Cu (II) of 63 ppm in a 0.5 M sulphuric
acid solution, both with a mass of the extracting agent of 20 mg, an
extraction percentage of about 97.8 % and a distribution coefficient
of 44.42 were obtained, respectively, confirming the performance
of the SDDT-Chloroform pair.
Abstract: This paper demonstrates the feasibility of replacing
the metal coil spring with the composite coil spring. Three different
types of springs were made using glass fiber, carbon fiber and
combination of glass fiber and carbon fiber. The objective of the
study is to reduce the weight of the spring. According to the
experimental results the spring rate of the carbon fiber spring is
34% more than the glass fiber spring and 45% more than the glass
fiber/carbon fiber spring. The weight of the carbon fiber spring is
18% less than the glass fiber spring, 15% less than the Glass
fiber/carbon fiber spring and 80% less than the steel spring.
Abstract: The objective of this work was to examine the changes
in non destructive properties caused by carbonation of CEM II
mortar. Samples of CEM II mortar were prepared and subjected to
accelerated carbonation at 20°C, 65% relative humidity and 20% CO2
concentration. We examined the evolutions of the gas permeability,
the thermal conductivity, the thermal diffusivity, the volume of the
solid phase by helium pycnometry, the longitudinal and transverse
ultrasonic velocities. The principal contribution of this work is that,
apart of the gas permeability, changes in other non destructive
properties have never been studied during the carbonation of cement
materials. These properties are important in predicting/measuring the
durability of reinforced concrete in CO2 environment. The
carbonation depth and the porosity accessible to water were also
reported in order to explain comprehensively the changes in non
destructive parameters.
Abstract: World population growth drives food demand, promotes intensification of agriculture, development of new production technologies and varieties more suitable for regional nature conditions. Climate change can affect the length of growing period, biomass and carbon accumulation in winter wheat. The increasing mean air temperature resulting from climate change can reduce the length of growth period of cereals, and without adequate adjustments in growing technologies or varieties, can reduce biomass and carbon accumulation. Deeper understanding and effective measures for monitoring and management of cereal growth process are needed for adaptation to changing climate and technological conditions.
Abstract: The study site was located in Ratchaburi Province,
Thailand. Four experimental plots in dry dipterocarp forest (DDF)
and four plots in mixed deciduous forest (MDF) were set up to
estimate the above-ground biomass of tree, sapling and bamboo. The
allometry equations were used to investigate above-ground biomass
of these vegetation. Seedling and other understory were determined
using direct harvesting method. Carbon storage in above-ground
biomass was calculated based on IPCC 2006.
The results showed that the above-ground biomass of DDF at
20-40% slope,
Abstract: spherical porous carbon particles with
controllable porosity with a mean size of 2.5m have been
prepared using a spray drying method with organic particle
colloidal template. As a precursor, a mixing solution of carbon
nanopowder and polystyrene (PS) particles as a template was
used. The result showed that the particles with a good porous
structure could be obtained. The pore size and shape (spherical)
were identical to the initial template, giving a potential way for
further developments. The control of particle porosity was also
possible and reported in this paper, in which this control could
be achieved by means of PS concentration.
Abstract: Fertilization plays an important role in crop growth and soil improvement. This study was conducted to determine the best fertilization system for wheat production. Experiments were arranged in a complete block design with three replications in two years. Main plots consisted of six methods of fertilization including (N1): farmyard manure; (N2): compost; (N3): chemical fertilizers; (N4): farmyard manure + compost; (N5): farmyard manure + compost + chemical fertilizers and (N6): control were arranged in sub plots. The addition of compost or farm yard manure significantly increased the soil microbial biomass carbon in comparison to the chemical fertilizer. The dehydrogenase, phosphatase and urease activities in the N3 treatment were significantly lower than in the farm yard manure and compost treatments.