Abstract: Polymeric materials have become an integral part of every aspect of today's industry. They have wide applications, inter alia, in areas such as medicine, food industry and agriculture. In agriculture, for example, they are used for the production of pots, irrigation systems and for soil mulching. The aim of this study was the attempt to produce a biodecomposable agricultural mat, by coating cotton fabric with a blend of carboxylated styrene-butadiene latex (LBSK) containing the enzymatic hydrolyzate of keratin from cattle hair, which would serve as a material for mulching.
The production of such material allows the beneficial management of burdensome tannery waste constituted by keratin from cattle hair and at the same time, the production of agricultural mats that much faster undergo decomposition than commonly used polyethylene mats.
Abstract: Crude oil is a major source of global energy. The major problem is its widespread use and demand resulted is in increasing environmental pollution. One associated pollution problem is ‘oil spills’. Oil spills can be remediated with the use of chemical dispersants, microbial biodegradation and microbial metabolites such as biosurfactants. Four different minimal salt media for biosurfactant production by Bacillus isolated from oil contaminated sites from Oman were screened. These minimal salt media were supplemented with either glucose or sucrose as a carbon source. Among the isolates, W16 and B30 produced the most active biosurfactants. Isolate W16 produced better biosurfactant than the rest, and reduced surface tension (ST) and interfacial tension (IFT) to 25.26mN/m and 2.29mN/m respectively within 48h which are characteristics for removal of oil in contaminated sites. Biosurfactant was produced in bulk and extracted using acid precipitation method. Thin Layer Chromatography (TLC) of acid precipitate biosurfactant revealed two concentrated bands. Further studies of W16 biosurfactant in bioremediation of oil spills are recommended.
Abstract: In this study sugarcane field soils with a long history of atrazine application in Chachoengsao and Chonburi provinces have been explored for their potential of atrazine biodegradation. For the atrazine degrading bacteria isolation, the soils used in this study named ACS and ACB were inoculated in MS-medium containing atrazine. Six short rod and gram-negative bacterial isolates, which were able to use this herbicide as a sole source of nitrogen, were isolated and named as ACS1, ACB1, ACB3, ACB4, ACB5 and ACB6. From the 16S rDNA nucleotide sequence analysis, the isolated bacteria ACS1 and ACB4 were identified as Rhizobium sp. with 89.1-98.7% nucleotide identity, ACB1 and ACB5 were identified as Stenotrophomonas sp. with 91.0-92.8% nucleotide identity, whereas ACB3 and ACB6 were Klebsiella sp. with 97.4-97.8% nucleotide identity.
Abstract: Water pollution is a major concern for the pulp and paper industry due to the large quantities of effluents generated. Biodegradation of industrial Lignin and AOX by a fungal isolate identified as Aspergillus flavus, white rot fungi which was isolated from Pulp and Paper effluent was studied in batch flask system with industrial effluent and synthetic solution. The flasks were operated at temperature 32°C at 200rpm for eight days in continuous mode. The average overall pH, Temperature, DO, C.O.D, T.D.S, T.S.S, Lignin, AOX were up to 4.56, 32oC, 4.2mg/l, 104mg/l, 6000 mg/l, 4000mg/l, 575.5mg/l, 2195 mg/l respectively after treatment. The Aspergillus flavus sp was the most effective in the biodegradation of Lignin of pulp industry for 94% at 480nm, AOX for 62% at 510nm and of chemical oxygen demand levels for 45% after 8 days of incubation. The optimal conditions found were 4 pH and 32oC temperature for lignin and AOX degradation.
Abstract: In this study, tapioca starch, which acts as natural polymer, was added in the blend in order to produce biodegradable product. Low density polyethylene (LDPE) and tapioca starch blends were prepared by extrusion and the test sample by injection moulding process. Ethylene vinyl acetate (EVA) acts as compatibilizer while glycerol as processing aid was added in the blend. The blends were characterized by using melt flow index (MFI), fourier transform infrared (FTIR) and the effects of water absorption to the sample. As the starch content increased, MFI of the blend was decreased. Tensile testing were conducted shows the tensile strength and elongation at break decreased while the modulus increased as the starch increased. For the biodegradation, soil burial test was conducted and the loss in weight was studied as the starch content increased. Morphology studies were conducted in order to show the distribution between LDPE and starch.
Abstract: According to synthetic plastics obtained from petroleum cause some environmental problems. Therefore, degradable plastics become widely used and studied for replacing the synthetic plastic waste. A biopolymer of poly hydroxybutyrate-co-hydroxyvalerate (PHBV) is subgroups of a main kind of polyhydroxyalkanoates (PHAs). Naturally, PHBV is hard, brittle and low flexible while natural rubber (NR) is high elastic latex. Then, they are blended and the biodegradation of the blended PHBV and NR films were examined in soil environment. The results showed that the degradation occurs predominantly in the bulk of the samples. The order of biodegradability was shown as follows: PHBV> PHBV/NR> NR. After biodegradation, the blended films were characterized by appearance analysis such as Scanning Electron Microscope (SEM), Fourier transform infrared spectroscopy (FTIR) and Differential Scanning Calorimetry (DSC). It was found that the biodegradation mainly occurred at the polymer surface.
Abstract: The objective of this research was to investigate biodegradation of water hyacinth (Eichhornia crassipes) to produce bioethanol using dilute-acid pretreatment (1% sulfuric acid) results in high hemicellulose decomposition and using yeast (Pachysolen tannophilus) as bioethanol producing strain. A maximum ethanol yield of 1.14g/L with coefficient, 0.24g g-1; productivity, 0.015g l-1h-1 was comparable to predicted value 32.05g/L obtained by Central Composite Design (CCD). Maximum ethanol yield coefficient was comparable to those obtained through enzymatic saccharification and fermentation of acid hydrolysate using fully equipped fermentor. Although maximum ethanol concentration was low in lab scale, the improvement of lignocellulosic ethanol yield is necessary for large scale production.
Abstract: Anaerobic digestion process is one of the alternative
methods to convert organic waste into methane gas which is a fuel
and energy source. Activities of various kinds of microorganisms are
the main factor for anaerobic digestion which produces methane gas.
Therefore, in this study a modified Anaerobic Baffled Reactor (ABR)
with working volume of 50 liters was designed to identify the
microorganisms through biogas production. The mixture of 75%
kitchen waste and 25% sewage sludge was used as substrate.
Observations on microorganisms in the ABR showed that there exists
a small amount of protozoa (5%) and fungi (2%) in the system, but
almost 93% of the microorganism population consists of bacteria. It
is definitely clear that bacteria are responsible for anaerobic
biodegradation of kitchen waste. Results show that in the
acidification zone of the ABR (front compartments of reactor) fast
growing bacteria capable of growth at high substrate levels and
reduced pH was dominant. A shift to slower growing scavenging
bacteria that grow better at higher pH was occurring towards the end
of the reactor. Due to the ability of activity in acetate environment the
percentages of Methanococcus, Methanosarcina and Methanotrix
were higher than other kinds of methane former in the system.
Abstract: Magnesium alloy has been widely investigated as
biodegradable cardiovascular stent and bone implant. Its application
for biodegradable esophageal stenting remains unexplored. This
paper reports the biodegradation behaviors of AZ31 magnesium alloy
in artificial saliva and various types of beverage in vitro. Results
show that the magnesium ion release rate of AZ31 in artificial saliva
for a stent (2cm diameter, 10cm length at 50% stent surface
coverage) is 43 times lower than the daily allowance of human body
magnesium intakes. The degradation rates of AZ31 in different
beverages could also be significantly different. These results suggest
that the esophagus in nature is a less aggressive chemical
environment for degradation of magnesium alloys. The significant
difference in degradation rates of AZ31 in different beverages opens
new opportunities for development of degradation controllable
esophageal stent through customizing ingested beverages.
Abstract: Atrazine, a herbicide widely used in sugarcane and corn production, is a frequently detected groundwater contaminant. An atrazine-degrading bacterium, strain KB02, was obtained from long-term atrazine-treated sugarcane field soils in Kanchanaburi province of Thailand. Strain KB02 had a rod-to-coccus morphological cycle during growth. Sequence analysis of the PCR product indicated that the 16S rRNA gene in strain KB02 was ranging from 97-98% identical to the same region in Klebsiella sp. Based on biochemical, physiological analysis and 16S rDNA sequence analysis of one representative isolate, strain KB02, the isolates belong to the genus Klebsiella in the family Enterobacteriaceae. Interestingly that the various primers for atzA, B and C failed to amplify genomic DNA of strain KB02. Whereas the expected PCR product of atzA, B and C were obtained from the reference strain, Arthrobacter sp. strain KU001.
Abstract: The objectives were to identify cyanide-degrading
bacteria and study cyanide removal efficiency. Agrobacterium
tumefaciens SUTS 1 was isolated. This is a new strain of
microorganisms for cyanide degradation. The maximum growth rate
of SUTS 1 obtained 4.7 × 108 CFU/ml within 4 days. The cyanide
removal efficiency was studied at 25, 50, and 150 mg/L cyanide. The
residual cyanide, ammonia, nitrate, nitrite, pH, and cell counts were
analyzed. At 25 and 50 mg/L cyanide, SUTS 1 obtained similar
removal efficiency approximately 87.50%. At 150 mg/L cyanide,
SUTS 1 enhanced the cyanide removal efficiency up to 97.90%. Cell
counts of SUTS 1 increased when the cyanide concentration was set
at lower. The ammonia increased when the removal efficiency
increased. The nitrate increased when the ammonia decreased but the
nitrite did not detect in all experiments. pH values also increased
when the cyanide concentrations were set at higher.
Abstract: In this study, cometabolic biodegradation of
chloroform was experimented with mixed cultures in the presence of
various organic solvents like methanol, ethanol, isopropanol, acetone,
acetonitrile and toluene as these are predominant discharges in
pharmaceutical industries. Toluene and acetone showed higher
specific chloroform degradation rate when compared to other
compounds. Cometabolic degradation of chloroform was further
confirmed by observation of free chloride ions in the medium. An
extended Haldane model, incorporating the inhibition due to
chloroform and the competitive inhibition between primary
substrates, was developed to predict the biodegradation of primary
substrates, cometabolic degradation of chloroform and the biomass
growth. The proposed model is based on the use of biokinetic
parameters obtained from single substrate degradation studies. The
model was able to satisfactorily predict the experimental results of
ternary and quaternary mixtures. The proposed model can be used for
predicting the performance of bioreactors treating discharges from
pharmaceutical industries.
Abstract: Pentachlorophenol (PCP) is a polychlorinated
aromatic compound that is widespread in industrial effluents and is
considered to be a serious pollutant. Among the variety of industrial
effluents encountered, effluents from tanning industry are very
important and have a serious pollution potential. PCP is also formed
unintentionally in effluents of paper and pulp industries. It is highly
persistent in soils and is lethal to a wide variety of beneficial
microorganisms and insects, human beings and animals. The natural
processes that breakdown toxic chemicals in the environment have
become the focus of much attention to develop safe and environmentfriendly
deactivation technologies. Microbes and plants are among
the most important biological agents that remove and degrade waste
materials to enable their recycling in the environment. The present
investigation was carried out with the aim of developing a microbial
system for bioremediation of PCP polluted soils. A number of plant
species were evaluated for their ability to tolerate different
concentrations of pentachlorophenol (PCP) in the soil. The
experiment was conducted for 30 days under pot culture conditions.
The toxic effect of PCP on plants was studied by monitoring seed
germination, plant growth and biomass. As the concentration of PCP
was increased to 50 ppm, the inhibition of seed germination, plant
growth and biomass was also increased. Although PCP had a
negative effect on all plant species tested, maize and groundnut
showed the maximum tolerance to PCP. Other tolerating crops
included wheat, safflower, sunflower, and soybean. From the
rhizosphere soil of the tolerant seedlings, as many as twenty seven
PCP tolerant bacteria were isolated. From soybean, 8; sunflower, 3;
safflower 8; maize 2; groundnut and wheat, 3 each isolates were
made. They were screened for their PCP degradation potentials.
HPLC analyses of PCP degradation revealed that the isolate MAZ-2
degraded PCP completely. The isolate MAZ-1 was the next best
isolate with 90 per cent PCP degradation. These strains hold promise
to be used in the bioremediation of PCP polluted soils.
Abstract: This current research focused on development of degradable starch based packaging film with enhanced mechanical properties. A series of low density polyethylene (LDPE)/tapioca starch compounds with various tapioca starch contents were prepared by twin screw extrusion with the addition of maleic anhydride grafted polyethylene as compatibilizer. Palm cooking oil was used as processing aid to ease the blown film process, thus, degradable film can be processed via conventional blown film machine. Studies on their characteristics, mechanical properties and biodegradation were carried out by Fourier Transform Infrared (FTIR) spectroscopy and optical properties, tensile test and exposure to fungi environment respectively. The presence of high starch contents had an adverse effect on the tensile properties of LDPE/tapioca starch blends. However, the addition of compatibilizer to the blends improved the interfacial adhesion between the two materials, hence, improved the tensile properties of the films. High content of starch amount also was found to increase the rate of biodegradability of LDPE/tapioca starch films. It can be proved by exposure of the film to fungi environment. A growth of microbes colony can be seen on the surface of LDPE/tapioca starch film indicates that the granular starch present on the surface of the polymer film is attacked by microorganisms, until most of it is assimilated as a carbon source.
Abstract: Lignocellulosic materials are considered the most
abundant renewable resource available for the Bioethanol
Production. Water Hyacinth is one of potential raw material of the
world-s worst aquatic plant as a feedstock to produce Bioethanol.
The purposed this research is obtain reduced of matter for
biodegradation lignin in Biological pretreatment with White Rot
Fungi eg. Phanerochaete Chrysosporium using Solid state
Fermentation methods. Phanerochaete Chrysosporium is known to
have the best ability to degraded lignin, but simultaneously it can also
degraded cellulose and hemicelulose. During 8 weeks incubation,
water hyacinth occurred loss of weight reached 34,67%, while loss
of lignin reached 67,21%, loss of cellulose reached 11,01% and loss
of hemicellulose reached 36,56%. The kinetic of losses lignin using
regression linear plot, the results is obtained constant rate (k) of
reduction lignin is -0.1053 and the equation of reduction of lignin
is y = wo - 0, 1.53 x
Abstract: Removal of PCP by a system combining
biodegradation by biofilm and adsorption was investigated here.
Three studies were conducted employing batch tests, sequencing
batch reactor (SBR) and continuous biofilm activated carbon
column reactor (BACCOR). The combination of biofilm-GAC
batch process removed about 30% more PCP than GAC adsorption
alone. For the SBR processes, both the suspended and attached
biomass could remove more than 90% of the PCP after
acclimatisation. BACCOR was able to remove more than 98% of
PCP-Na at concentrations ranging from 10 to 100 mg/L, at empty
bed contact time (EBCT) ranging from 0.75 to 4 hours. Pure and
mixed cultures from BACCOR were tested for use of PCP as sole
carbon and energy source under aerobic conditions. The isolates
were able to degrade up to 42% of PCP under aerobic conditions in
pure cultures. However, mixed cultures were found able to degrade
more than 99% PCP indicating interdependence of species.
Abstract: Composting is the process in which municipal solid
waste (MSW) and other organic waste materials such as biosolids
and manures are decomposed through the action of bacteria and other
microorganisms into a stable granular material which, applied to
land, as soil conditioner. Microorganisms, especially those that are
able to degrade polymeric organic material have a key role in speed
up this process. The aim of this study has been established to
isolation of microorganisms with high ability to production
extracellular enzymes for degradation of natural polymers that are
exists in MSW for decreasing time of degradation phase. Our
experimental study for isolation designed in two phases: in first
phase we isolated degrading microorganism with selected media that
consist a special natural polymer such as cellulose, starch, lipids and
etc as sole source of carbon. In second phase we selected
microorganism that had high degrading enzyme production with
enzymatic assay for seed production. However, our findings in pilot
scale have indicated that usage of this microbial consortium had high
efficiency for decreasing degradation phase.
Abstract: Although oil-based drilling fluids are of paramount practical and economical interest, they represent a serious source of pollution, once released into the environment as drill cuttings. The aim of this study is to assess the capability of isolated microorganisms to degrade gasoil fuel. The commonly used physicochemical and biodegradation remediation techniques of petroleum contaminated soil were both investigated. The study revealed that natural biodegradation is favorable. Even though, the presence of heavy metals, the moisture level of (8.55%) and nutrient deficiencies put severe constrains on microorganisms- survival ranges inhibiting the biodegradation process. The selected strains were able to degrade the diesel fuel at significantly high rates (around 98%).
Abstract: In the present work we report a gram negative
bacterial isolate, from soil of a dye industry, with promising
biorefining and bioremediation potential. This isolate (GBS.5) could
utilize carbazole (nitrogen containing polycyclic aromatic
hydrocarbon) as the sole source of nitrogen and carbon and utilize
almost 98% of 3mM carbazole in 100 hours. The specific activity of
our GBS.5 isolate for carbazole degradation at 30°C and pH 7.0 was
found to be 11.36 μmol/min/g dry cell weight as compared to 10.4
μmol/min/g dry cell weight, the highest reported specific activity till
date. The presence of car genes (the genes involved in
denitrogenation of carbazole) was confirmed through PCR
amplification.