Abstract: Multidrug resistant organisms have been taunting the
medical world for the last few decades. Even with new antibiotics
developed, resistant strains have emerged soon after. With the
advancement of nanotechnology, we investigated colloidal silver
nanoparticles for its antimicrobial activity against Pseudomonas
aeruginosa. This organism is a multidrug resistant which contributes
to the high morbidity and mortality in immunocompromised patients.
Five multidrug resistant strains were used in this study. The
antimicrobial effect was studied using the disc diffusion and broth
dilution techniques. An inhibition zone of 11 mm was observed with
10 μg dose of the nanoparticles. The nanoparticles exhibited MIC of
50 μg/ml when added at the lag phase and the subinhibitory
concentration was measured as 100 μg/ml. The MIC50 value showed
to be 15 μg/ml. This study suggests that silver nanoparticles can be
further developed as an antimicrobial agent, hence decreasing the
burden of the multidrug resistance phenomena.
Abstract: In the present study, the effects of ultrasound as
emerging technology were investigated on germination stimulation,
amount of alpha-amylase activity on dry barley seeds before steeping
stage of malting process. All experiments were carried out at 20 KHz
on the ultrasonic generator in 3 different ultrasonic intensities (20, 60
and 100% setting from total power of device) and time (5, 10 and 15
min) at constant temperature (30C). For determining the effects of
these parameters on enzyme the Fuwa method assay based on the
decreased staining value of blue starch–iodine complexes employed
for measurement an activity. The results of these assays were
analyzed by Qualitek4 software using the Taguchi statistical method
to evaluate the factor-s effects on enzyme activity. It has been found
that when malting barley is irradiated with an ultrasonic power, a
stimulating effect occurs as to the enzyme activity.
Abstract: The modified Claus process is the major technology
for the recovery of elemental sulfur from hydrogen sulfide. The
chemical reactions that can occur in the reaction furnace are
numerous and many byproducts such as carbon disulfide and carbon
carbonyl sulfide are produced. These compounds can often contribute
from 20 to 50% of the pollutants and therefore, should be hydrolyzed
in the catalytic converter. The inlet temperature of the first catalytic
reactor should be maintained over than 250 °C, to hydrolyze COS
and CS2. In this paper, the various configurations for the first
converter reheating of sulfur recovery unit are investigated. As a
result, the performance of each method is presented for a typical
clause unit. The results show that the hot gas method seems to be
better than the other methods.
Abstract: The rapid pace of technological advancement and its
consequential widening digital divide has resulted in the
marginalization of the disabled especially the communication
challenged. The dearth of suitable technologies for the development
of assistive technologies has served to further marginalize the
communications challenged user population and widen this chasm
even further. Given the varying levels of disability there and its
associated requirement for customized solution based. This paper
explains the use of a Software Development Kits (SDK) for the
bridging of this communications divide through the use of industry
poplar communications SDKs towards identification of requirements
for communications challenged users as well as identification of
appropriate frameworks for future development initiatives.
Abstract: If organizations like Mellat Bank want to identify its
customer market completely to reach its specified goals, it can
segment the market to offer the product package to the right segment.
Our objective is to offer a segmentation model for Iran banking
market in Mellat bank view. The methodology of this project is
combined by “segmentation on the basis of four part-quality
variables" and “segmentation on the basis of different in means".
Required data are gathered from E-Systems and researcher personal
observation. Finally, the research offers the organization that at first
step form a four dimensional matrix with 756 segments using four
variables named value-based, behavioral, activity style, and activity
level, and at the second step calculate the means of profit for every
cell of matrix in two distinguished work level (levels α1:normal
condition and α2: high pressure condition) and compare the segments
by checking two conditions that are 1- homogeneity every segment
with its sub segment and 2- heterogeneity with other segments, and
so it can do the necessary segmentation process. After all, the last
offer (more explained by an operational example and feedback
algorithm) is to test and update the model because of dynamic
environment, technology, and banking system.
Abstract: This paper proposes a low power SRAM based on
five transistor SRAM cell. Proposed SRAM uses novel word-line
decoding such that, during read/write operation, only selected cell
connected to bit-line whereas, in conventional SRAM (CV-SRAM),
all cells in selected row connected to their bit-lines, which in turn
develops differential voltages across all bit-lines, and this makes
energy consumption on unselected bit-lines. In proposed SRAM
memory array divided into two halves and this causes data-line
capacitance to reduce. Also proposed SRAM uses one bit-line and
thus has lower bit-line leakage compared to CV-SRAM.
Furthermore, the proposed SRAM incurs no area overhead, and has
comparable read/write performance versus the CV-SRAM.
Simulation results in standard 0.25μm CMOS technology shows in
worst case proposed SRAM has 80% smaller dynamic energy
consumption in each cycle compared to CV-SRAM. Besides, energy
consumption in each cycle of proposed SRAM and CV-SRAM
investigated analytically, the results of which are in good agreement
with the simulation results.
Abstract: This paper presents an application of 5S lean technology to a production facility. Due to increased demand, high product variety, and a push production system, the plant has suffered from excessive wastes, unorganized workstations, and unhealthy work environment. This has translated into increased production cost, frequent delays, and low workers morale. Under such conditions, it has become difficult, if not impossible, to implement effective continuous improvement studies. Hence, the lean project is aimed at diagnosing the production process, streamlining the workflow, removing/reducing process waste, cleaning the production environment, improving plant layout, and organizing workstations. 5S lean technology is utilized for achieving project objectives. The work was a combination of both culture changes and tangible/physical changes on the shop floor. The project has drastically changed the plant and developed the infrastructure for a successful implementation of continuous improvement as well as other best practices and quality initiatives.
Abstract: A virtual collaborative classroom was created at East Carolina University, using videoconference technology via regular internet to bring students from 18 different countries, 2 at a time, to the ECU classroom in real time to learn about each other-s culture. Students from two countries are partnered one on one, they meet for 4-5 weeks, and submit a joint paper. Then the same process is repeated for two other countries. Lectures and student discussions are managed with pre-determined topics and questions. Classes are conducted in English and reading assignments are placed on the website. Administratively all partners are independent, students pay fees and get credits at their home institution. Familiarity with technology, knowledge in cultural understanding and attitude change were assessed, only attitude changes are reported in this paper. After taking this course, all students stated their comfort level in working with, and their desire to interact with, culturally different others grew stronger and their xenophobia and isolationist attitudes decreased.
Abstract: We developed a non-contact method for the in-situ
monitoring of the thermal forming of glass and Si foils to optimize
the manufacture of mirrors for high-resolution space x-ray
telescopes. Their construction requires precise and light-weight
segmented optics with angular resolution better than 5 arcsec. We
used 75x25 mm Desag D263 glass foils 0.75 mm thick and 0.6 mm
thick Si foils. The glass foils were shaped by free slumping on a
frame at viscosities in the range of 109.3-1012 dPa·s, the Si foils by
forced slumping above 1000°C. Using a Nikon D80 digital camera,
we took snapshots of a foil-s shape every 5 min during its isothermal
heat treatment. The obtained results we can use for computer
simulations. By comparing the measured and simulated data, we can
more precisely define material properties of the foils and optimize
the forming technology.
Abstract: As global industry developed rapidly, the energy
demand also rises simultaneously. In the production process, there’s a
lot of energy consumed in the process. Formally, the energy used in
generating the heat in the production process. In the total energy
consumption, 40% of the heat was used in process heat, mechanical
work, chemical energy and electricity. The remaining 50% were
released into the environment. It will cause energy waste and
environment pollution. There are many ways for recovering the waste
heat in factory. Organic Rankine Cycle (ORC) system can produce
electricity and reduce energy costs by recovering the waste of low
temperature heat in the factory. In addition, ORC is the technology
with the highest power generating efficiency in low-temperature heat
recycling. However, most of factories executives are still hesitated
because of the high implementation cost of the ORC system, even a lot
of heat are wasted. Therefore, this study constructs a nonlinear
mathematical model of waste heat recovery equipment configuration
to maximize profits. A particle swarm optimization algorithm is
developed to generate the optimal facility installation plan for the ORC
system.
Abstract: Quality of 2D and 3D cross-sectional images produce
by Computed Tomography primarily depend upon the degree of
precision of primary and secondary X-Ray intensity detection.
Traditional method of primary intensity detection is apt to errors.
Recently the X-Ray intensity measurement system along with smart
X-Ray sensors is developed by our group which is able to detect
primary X-Ray intensity unerringly. In this study a new smart X-Ray
sensor is developed using Light-to-Frequency converter TSL230
from Texas Instruments which has numerous advantages in terms of
noiseless data acquisition and transmission. TSL230 construction is
based on a silicon photodiode which converts incoming X-Ray
radiation into the proportional current signal. A current to frequency
converter is attached to this photodiode on a single monolithic CMOS
integrated circuit which provides proportional frequency count to
incoming current signal in the form of the pulse train. The frequency
count is delivered to the center of PICDEM FS USB board with
PIC18F4550 microcontroller mounted on it. With highly compact
electronic hardware, this Demo Board efficiently read the smart
sensor output data. The frequency output approaches overcome
nonlinear behavior of sensors with analog output thus un-attenuated
X-Ray intensities could be measured precisely and better
normalization could be acquired in order to attain high resolution.
Abstract: Concrete performance is strongly affected by the
particle packing degree since it determines the distribution of the
cementitious component and the interaction of mineral particles. By
using packing theory designers will be able to select optimal
aggregate materials for preparing concrete with low cement content,
which is beneficial from the point of cost. Optimum particle packing
implies minimizing porosity and thereby reducing the amount of
cement paste needed to fill the voids between the aggregate particles,
taking also the rheology of the concrete into consideration. For
reaching good fluidity superplasticizers are required. The results from
pilot tests at Luleå University of Technology (LTU) show various
forms of the proposed theoretical models, and the empirical approach
taken in the study seems to provide a safer basis for developing new,
improved packing models.
Abstract: This paper deals with a new way for designing
external fixators applied in traumatology and orthopaedics. These
fixators can be applied in the treatment of open and unstable
fractures or for lengthening human or animal bones etc. The new
design is based on the development of Ilizarov and other techniques
(i.e. shape and weight optimalization based on composite materials,
application of smart materials, nanotechnology, low x-ray absorption,
antibacterial protection, patient's comfort, reduction in the duration
of the surgical treatment, and cost).
Abstract: Bangladesh is a developing country with large
population. Demand of electrical energy is increasing day by day
because of increasing population and industrialization. But due to
limited resources, people here are suffering from power crisis
problem which is considered as a major obstacle to the economic
development. In most of the cases, it is extremely difficult to extend
high tension transmission lines to some of the places that are
separated from the mainland. Renewable energy is considered to be
the right choice for providing clean energy to these remote
settlements. This paper proposes a cost effective design of off-grid
wind-diesel hybrid power system using combined heat and power
(CHP) technology in a grid isolated island, Sandwip, Bangladesh.
Design and simulation of the wind-diesel hybrid power system is
performed considering different factors for the island Sandwip.
Detailed economic analysis and comparison with solar PV system
clearly reveals that wind-diesel hybrid power system can be a cost
effective solution for the isolated island like Sandwip.
Abstract: An interesting method to produce calcium carbonate is based in a gas-liquid reaction between carbon dioxide and aqueous solutions of calcium hydroxide. The design parameters for gas-liquid phase are flow regime, individual mass transfer, gas-liquid specific interfacial area. Most studies on gas-liquid phase were devoted to the experimental determination of some of these parameters, and more specifically, of the mass transfer coefficient, kLa which depends fundamentally on the superficial gas velocity and on the physical properties of absorption phase. The principle investigation was directed to study the effect of the vibration on the mass transfer coefficient kLa in gas-liquid phase during absorption of CO2 in the in aqueous solution of calcium hydroxide. The vibration with a higher frequency increase the mass transfer coefficient kLa, but vibration with lower frequency didn-t improve it, the mass transfer coefficient kLa increase with increase the superficial gas velocity.
Abstract: Although many studies on the assembly technology of
the bridge construction have dealt mostly with on the pier, girder or the
deck of the bridge, studies on the prefabricated barrier have rarely been
performed. For understanding structural characteristics and
application of the concrete barrier in the modular bridge, which is an
assembly of structure members, static loading test was performed.
Structural performances as a road barrier of the three methods,
conventional cast-in-place(ST), vertical bolt connection(BVC) and
horizontal bolt connection(BHC) were evaluated and compared
through the analyses of load-displacement curves, strain curves of the
steel, concrete strain curves and the visual appearances of crack
patterns. The vertical bolt connection(BVC) method demonstrated
comparable performance as an alternative to conventional
cast-in-place(ST) while providing all the advantages of prefabricated
technology. Necessities for the future improvement in nuts
enforcement as well as legal standard and regulation are also
addressed.
Abstract: In this study, we propose a network architecture for
providing secure access to information resources of enterprise
network from remote locations in a wireless fashion. Our proposed
architecture offers a very promising solution for organizations which
are in need of a secure, flexible and cost-effective remote access
methodology. Security of the proposed architecture is based on
Virtual Private Network technology and a special role based access
control mechanism with location and time constraints. The flexibility
mainly comes from the use of Internet as the communication medium
and cost-effectiveness is due to the possibility of in-house
implementation of the proposed architecture.
Abstract: Property investment in the real estate industry has a
high risk due to the uncertainty factors that will affect the decisions
made and high cost. Analytic hierarchy process has existed for some
time in which referred to an expert-s opinion to measure the
uncertainty of the risk factors for the risk analysis. Therefore,
different level of experts- experiences will create different opinion
and lead to the conflict among the experts in the field. The objective
of this paper is to propose a new technique to measure the uncertainty
of the risk factors based on multidimensional data model and data
mining techniques as deterministic approach. The propose technique
consist of a basic framework which includes four modules: user,
technology, end-user access tools and applications. The property
investment risk analysis defines as a micro level analysis as the
features of the property will be considered in the analysis in this
paper.
Abstract: Documents clustering become an essential technology
with the popularity of the Internet. That also means that fast and
high-quality document clustering technique play core topics. Text
clustering or shortly clustering is about discovering semantically
related groups in an unstructured collection of documents. Clustering
has been very popular for a long time because it provides unique
ways of digesting and generalizing large amounts of information.
One of the issues of clustering is to extract proper feature (concept)
of a problem domain. The existing clustering technology mainly
focuses on term weight calculation. To achieve more accurate
document clustering, more informative features including concept
weight are important. Feature Selection is important for clustering
process because some of the irrelevant or redundant feature may
misguide the clustering results. To counteract this issue, the proposed
system presents the concept weight for text clustering system
developed based on a k-means algorithm in accordance with the
principles of ontology so that the important of words of a cluster can
be identified by the weight values. To a certain extent, it has resolved
the semantic problem in specific areas.
Abstract: This paper reviews the objectives, methods and results of previous studies on biodrying of solid waste in several countries. Biodrying of solid waste is a novel technology in developing countries such as in Malaysia where high moisture content in organic waste makes the segregation process for recycling purposes complicated and diminishes the calorific value for the use of fuel source. In addition, the high moisture content also encourages the breeding of vectors and disease-bearing animals. From the laboratory results, the average moisture content of organic waste, paper, plastics and metals are 58.17%, 37.93%, 29.79% and 1.03% respectively for UKM campus. Biodrying of solid waste is a simple method of waste treatment as well as a cost-efficient technology to dry the solid waste. The process depends on temperature monitoring and air flow control along with the natural biodegradable process of organic waste. This review shows that the biodrying of solid waste method has high potential in treatment and recycling of solid waste, be useful for biodrying study and implementation in Malaysia.