Abstract: This paper presents the data of a series of two-dimensional Discrete Element Method (DEM) simulations of a large-diameter rigid monopile subjected to cyclic loading under a high gravitational force. At present, monopile foundations are widely used to support the tall and heavy wind turbines, which are also subjected to significant from wind and wave actions. A safe design must address issues such as rotations and changes in soil stiffness subject to these loadings conditions. Design guidance on the issue is limited, so are the availability of laboratory and field test data. The interpretation of these results in sand, such as the relation between loading and displacement, relies mainly on empirical correlations to pile properties. Regarding numerical models, most data from Finite Element Method (FEM) can be found. They are not comprehensive, and most of the FEM results are sensitive to input parameters. The micro scale behaviour could change the mechanism of the soil-structure interaction. A DEM model was used in this paper to study the cyclic lateral loads behaviour. A non-dimensional framework is presented and applied to interpret the simulation results. The DEM data compares well with various set of published experimental centrifuge model test data in terms of lateral deflection. The accumulated permanent pile lateral displacements induced by the cyclic lateral loads were found to be dependent on the characteristics of the applied cyclic load, such as the extent of the loading magnitudes and directions.
Abstract: Experimental and analytical studies were carried out to investigate the structural behavior of precast foamed concrete sandwich panels (PFCSP) of total number (6) as one-way action slab tested under lateral load. The details of the test setup and procedures were illustrated. The results obtained from the experimental tests were discussed which include the observation of cracking patterns and influence of aspect ratio (L/b). Analytical study of finite element analysis was implemented and degree of composite action of the test panels was also examined in both experimental and analytical studies. Result shows that crack patterns appeared in only one-direction, similar to reports on solid slabs, particularly when both concrete wythes act in a composite manner. Foamed concrete was briefly reviewed and experimental results were compared with the finite element analyses data which gives a reasonable degree of accuracy. Therefore, based on the results obtained, PFCSP slab can be used as an alternative to conventional flooring system.
Abstract: This paper attempted to assess whether the size of the regional economic bloc has an impact to the flow of trade to a particular country. Two different sized blocs (COMESA and EAC) and one country (Tanzania) have been used as the point of references. Using the results from of the analyses, the paper also was anticipated to establish whether it was rational for Tanzania to withdraw its membership from COMESA (the larger bloc) to join EAC (the small one). Gravity model has been used to estimate the relationship between the variables, from which the bilateral trade flows between Tanzania and the eighteen member countries of the two blocs (COMESA and EAC) was employed for the time between 2000 and 2013. In the model, the dummy variable for regional bloc (bloc) at which the Tanzania trade partner countries belong are also added to the model to understand which trade bloc exhibit higher trade flow with Tanzania. From the findings, it was noted that over the period of study (2000-2013) Tanzania acknowledged more than 257% of trade volume in EAC than in COMESA. Conclusive, it was noted that the flow of trade is explained by many other variables apart from the size of regional bloc; and that the size by itself offer insufficient evidence in causality relationship. The paper therefore remain neutral on such staggered switching decision since more analyses are required to establish the country’s trade flow, especially when if it had been in multiple membership of COMESA and EAC.
Abstract: Background: Plantar pressure measurement is an effective method for assessing plantar loading and can be applied to evaluating movement performance of the foot. The purpose of this study is to explore the sprint athletes’ plantar loading characteristics and pain profiles in static standing. Methods: Experiments were undertaken on 80 first-division college sprint athletes and 85 healthy non-sprinters. ‘JC Mat’, the optical plantar pressure measurement was applied to examining the differences between both groups in the arch index (AI), three regional and six distinct sub-regional plantar pressure distributions (PPD), and footprint characteristics. Pain assessment and self-reported health status in sprint athletes were examined for evaluating their common pain areas. Results: Findings from the control group, the males’ AI fell into the normal range. Yet, the females’ AI was classified as the high-arch type. AI values of the sprint group were found to be significantly lower than the control group. PPD were higher at the medial metatarsal bone of both feet and the lateral heel of the right foot in the sprint group, the males in particular, whereas lower at the medial and lateral longitudinal arches of both feet. Footprint characteristics tended to support the results of the AI and PPD, and this reflected the corresponding pressure profiles. For the sprint athletes, the lateral knee joint and biceps femoris were the most common musculoskeletal pains. Conclusions: The sprint athletes’ AI were generally classified as high arches, and that their PPD were categorized between the features of runners and high-arched runners. These findings also correspond to the profiles of patellofemoral pain syndrome (PFPS)-related plantar pressure. The pain profiles appeared to correspond to the symptoms of high-arched runners and PFPS. The findings reflected upon the possible link between high arches and PFPS. The correlation between high-arched runners and PFPS development is worth further studies.
Abstract: Soil improvement using vibro stone column techniques consists of two main parts: (1) the installed load bearing columns of well-compacted, coarse-grained material and (2) the improvements to the surrounding soil due to vibro compaction. Extensive research work has been carried out over the last 20 years to understand the improvement in the composite foundation performance due to the second part mentioned above. Nevertheless, few of these studies have tried to quantify some of the key design parameters, namely the changes in the stiffness and stress state of the treated soil, or have consider these parameters in the design and calculation process. Consequently, empirical and conservative design methods are still being used by ground improvement companies with a significant variety of results in engineering practice. Two-dimensional finite element study to develop an axisymmetric model of a single stone column reinforced foundation was performed using PLAXIS 2D AE to quantify the effect of the vibro installation of this column in soft saturated clay. Settlement and bearing performance were studied as an essential part of the design and calculation of the stone column foundation. Particular attention was paid to the large deformation in the soft clay around the installed column caused by the lateral expansion. So updated mesh advanced option was taken in the analysis. In this analysis, different degrees of stone column lateral expansions were simulated and numerically analyzed, and then the changes in the stress state, stiffness, settlement performance and bearing capacity were quantified. It was found that application of radial expansion will produce a horizontal stress in the soft clay mass that gradually decrease as the distance from the stone column axis increases. The excess pore pressure due to the undrained conditions starts to dissipate immediately after finishing the column installation, allowing the horizontal stress to relax. Changes in the coefficient of the lateral earth pressure K ٭, which is very important in representing the stress state, and the new stiffness distribution in the reinforced clay mass, were estimated. More encouraging results showed that increasing the expansion during column installation has a noticeable effect on improving the bearing capacity and reducing the settlement of reinforced ground, So, a design method should include this significant effect of the applied lateral displacement during the stone column instillation in simulation and numerical analysis design.
Abstract: This study investigated the differences in the objective parameters of sound depending on the changes in the lengths of the lateral surfaces of a space and on the replacement of the sound absorbers that are placed on these surfaces. To this end, three models of room were chosen. The widths and heights of these rooms were the same but the lengths of the rooms were changed. The smallest room was 8 m. wide and 10 m. long. The lengths of the other two rooms were 15 m. and 20 m. For each model, the differences in the objective parameters of sound were determined by keeping all the material in the space intact and by changing only the positions of the sound absorbers that were placed on the walls. The sound absorbers that were used on the walls were of two different sizes. The sound absorbers that were placed on the walls were 4 m and 8 m. long and story-height (3 m.). In all model room types, the sound absorbers were placed on the long walls in three different ways: at the end of the long walls where the long walls meet the front wall; at the end of the long walls where the long walls meet the back wall; and in the middle part of the long walls. Except for the specially placed sound absorbers, the ground, wall and ceiling surfaces were covered with three different materials. There were no constructional elements such as doors and windows on the walls. On the surfaces, the materials specified in the Odeon 10 material library were used as coating material. Linoleum was used as flooring material, painted plaster as wall coating material and gypsum boards as ceiling covering (2 layers with a total of 32 mm. thickness). These were preferred due to the fact that they are the commonly used materials for these purposes. This study investigated the differences in the objective parameters of sound depending on the changes in the lengths of the lateral surfaces of a space and on the replacement of the sound absorbers that are placed on these surfaces. To this end, three models of room were chosen. The widths and heights of these rooms were the same but the lengths of the rooms were changed. The smallest room was 8 m. wide and 10 m. long. The lengths of the other two rooms were 15 m. and 20 m. For each model, the differences in the objective parameters of sound were determined by keeping all the material in the space intact and by changing only the positions of the sound absorbers that were placed on the walls. The sound absorbers that were used on the walls were of two different sizes. The sound absorbers that were placed on the walls were 4 m and 8 m. long and story-height (3 m.). In all model room types, the sound absorbers were placed on the long walls in three different ways: at the end of the long walls where the long walls meet the front wall; at the end of the long walls where the long walls meet the back wall; and in the middle part of the long walls. Except for the specially placed sound absorbers, the ground, wall and ceiling surfaces were covered with three different materials. There were no constructional elements such as doors and windows on the walls. On the surfaces, the materials specified in the Odeon 10 material library were used as coating material. Linoleum was used as flooring material, painted plaster as wall coating material and gypsum boards as ceiling covering (2 layers with a total of 32 mm. thickness). These were preferred due to the fact that they are the commonly used materials for these purposes.
Abstract: Ultrasonic metal welding has been the subject of ongoing research and development, most recently concentrating on metal joining in miniature devices, for example to allow solder-free wire bonding. As well as at the small scale, there are also opportunities to research the joining of thicker sheet metals and to widen the range of similar and dissimilar materials that can be successfully joined using this technology. This study presents the design, characterisation and test of a lateral-drive ultrasonic metal spot welding device. The ultrasonic metal spot welding horn is modelled using finite element analysis (FEA) and its vibration behaviour is characterised experimentally to ensure ultrasonic energy is delivered effectively to the weld coupon. The welding stack and fixtures are then designed and mounted on a test machine to allow a series of experiments to be conducted for various welding and ultrasonic parameters. Weld strength is subsequently analysed using tensile-shear tests. The results show how the weld strength is particularly sensitive to the combination of clamping force and ultrasonic vibration amplitude of the welding tip, but there are optimal combinations of these and also limits that must be clearly identified.
Abstract: For several hundred years, the design of railway tracks
has practically remained unchanged. Traditionally, rail tracks are
placed on a ballast layer due to several reasons, including economy,
rapid drainage, and high load bearing capacity. The primary function
of ballast is to distributing dynamic track loads to sub-ballast and
subgrade layers, while also providing lateral resistance and allowing
for rapid drainage. Upon repeated trainloads, the ballast becomes
fouled due to ballast degradation and the intrusion of fines which
adversely affects the strength and deformation behaviour of ballast.
This paper presents the use of three-dimensional discrete element
method (DEM) in studying the shear behaviour of the fouled ballast
subjected to direct shear loading. Irregularly shaped particles of
ballast were modelled by grouping many spherical balls together in
appropriate sizes to simulate representative ballast aggregates. Fouled
ballast was modelled by injecting a specified number of miniature
spherical particles into the void spaces. The DEM simulation
highlights that the peak shear stress of the ballast assembly decreases
and the dilation of fouled ballast increases with an increase level of
fouling. Additionally, the distributions of contact force chain and
particle displacement vectors were captured during shearing progress,
explaining the formation of shear band and the evolutions of
volumetric change of fouled ballast.
Abstract: A 15-storey RC building, studied in this paper, is
representative of modern building type constructed in Madina City in
Saudi Arabia before 10 years ago. These buildings are almost
consisting of reinforced concrete skeleton i.e. columns, beams and
flat slab as well as shear walls in the stairs and elevator areas
arranged in the way to have a resistance system for lateral loads
(wind – earthquake loads). In this study, the dynamic properties of
the 15-storey RC building were identified using ambient motions
recorded at several, spatially-distributed locations within each
building. Three dimensional pushover analysis (Nonlinear static
analysis) was carried out using SAP2000 software incorporating
inelastic material properties for concrete, infill and steel. The effect
of modeling the building with and without infill walls, on the
performance point as well as capacity and demand spectra due to EQ
design spectrum function in Madina area has been investigated. ATC-
40 capacity and demand spectra are utilized to get the modification
factor (R) for the studied building. The purpose of this analysis is to
evaluate the expected performance of structural systems by
estimating, strength and deformation demands in design, and
comparing these demands to available capacities at the performance
levels of interest. The results are summarized and discussed.
Abstract: One of the main purposes of designing bucklingrestrained
braces is the fact that the entire lateral load is wasted by
the braces, the entire gravitational load is moved to the foundation
through the beams, and the columns can be moved to the foundation.
In other words, braces are designed for bearing lateral load. In the
implementation of the structure, it should be noted that the
implementation of various parts of the structure must be conducted in
such a way that the buckling-restrained braces would not bear the
gravitational load. Moreover, this type of brace has been investigated
under impact loading, and the design goals of designing method
(direct motion) are controlled under impact loading. The results of
dynamic analysis are shown as the relocation charts of the floors and
switch between the floors. Finally, the results are compared with each
other.
Abstract: Objective: Safety and efficacy of Ahmed glaucoma
valve implantation for the management of uveitis induced glaucoma
evaluated on the five dogs with uncontrollable glaucoma. Materials
and Methods: Ahmed Glaucoma Valve (AGV®; New World
Medical, Rancho Cucamonga, CA, USA) is a flow restrictive, nonobstructive
self-regulating valve system. Preoperative ocular
evaluation included direct ophthalmoscopy and measurement of the
intraocular pressure (IOP). The implant was examined and primed
prior to implantation. The selected site of the valve implantation was
the superior quadrant between the superior and lateral rectus muscles.
A fornix-based incision was made through the conjunectiva and
Tenon’s capsule. A pocket is formed by blunt dissection of Tenon’s
capsule from the episclera. The body of the implant was inserted into
the pocket with the leading edge of the device around 8-10 mm from
the limbus. Results: No post-operative complications were detected
in the operated eyes except a persistent corneal edema occupied the
upper half of the cornea in one case. Hyphaema was very mild and
seen only in two cases which resolved quickly two days after surgery.
Endoscopical evaluation for the operated eyes revealed a normal
ocular fundus with clearly visible optic papilla, tapetum and retinal
blood vessels. No evidence of hemorrhage, infection, adhesions or
retinal abnormalities was detected. Conclusion: Ahmed glaucoma
valve is safe and effective implant for treatment of uveitic glaucoma
in dogs.
Abstract: This study investigates how the site specific traffic
data differs from the Mechanistic Empirical Pavement Design
Software default values. Two Weigh-in-Motion (WIM) stations were
installed in Interstate-40 (I-40) and Interstate-25 (I-25) to developed
site specific data. A computer program named WIM Data Analysis
Software (WIMDAS) was developed using Microsoft C-Sharp (.Net)
for quality checking and processing of raw WIM data. A complete
year data from November 2013 to October 2014 was analyzed using
the developed WIM Data Analysis Program. After that, the vehicle
class distribution, directional distribution, lane distribution, monthly
adjustment factor, hourly distribution, axle load spectra, average
number of axle per vehicle, axle spacing, lateral wander distribution,
and wheelbase distribution were calculated. Then a comparative
study was done between measured data and AASHTOWare default
values. It was found that the measured general traffic inputs for I-40
and I-25 significantly differ from the default values.
Abstract: The floor beams of steel buildings, cold-formed steel
floor joists in particular, often require large web openings, which may
affect their shear capacities. A cost effective way to mitigate the
detrimental effects of such openings is to weld/fasten reinforcements.
A difficulty associated with an experimental investigation to establish
suitable reinforcement schemes for openings in shear zone is that
moment always coexists with the shear, and thus, it is impossible to
create pure shear state in experiments, resulting in moment
influenced results. However, Finite Element Method (FEM) based
analysis can be conveniently used to investigate the pure shear
behaviour of webs including webs with reinforced openings. This
paper presents the details associated with the finite element analysis
of thick/thin-plates (representing the web of hot-rolled steel beam,
and the web of a cold-formed steel member) having a large
reinforced opening. The study considered simply-supported
rectangular plates subjected to in-plane shear loadings until failure
(including post-buckling behaviour). The plate was modelled using
geometrically non-linear quadrilateral shell elements, and non-linear
stress-strain relationship based on experiments. Total Langrangian
with large displacement/small strain formulation was used for such
analyses. The model also considered the initial geometric
imperfections. This study considered three reinforcement schemes,
namely, flat, lip, and angle reinforcements. This paper discusses the
modelling considerations and presents the results associated with the
various reinforcement schemes under consideration.
Abstract: Lateral Geniculate Nucleus (LGN) is the relay center
in the visual pathway as it receives most of the input information
from retinal ganglion cells (RGC) and sends to visual cortex. Low
threshold calcium currents (IT) at the membrane are the unique
indicator to characterize this firing functionality of the LGN neurons
gained by the RGC input. According to the LGN functional
requirements such as functional mapping of RGC to LGN, the
morphologies of the LGN neurons were developed. During the
neurological disorders like glaucoma, the mapping between RGC and
LGN is disconnected and hence stimulating LGN electrically using
deep brain electrodes can restore the functionalities of LGN. A
computational model was developed for simulating the LGN neurons
with three predominant morphologies each representing different
functional mapping of RGC to LGN. The firings of action potentials
at LGN neuron due to IT were characterized by varying the
stimulation parameters, morphological parameters and orientation. A
wide range of stimulation parameters (stimulus amplitude, duration
and frequency) represents the various strengths of the electrical
stimulation with different morphological parameters (soma size,
dendrites size and structure). The orientation (0-1800) of LGN
neuron with respect to the stimulating electrode represents the angle
at which the extracellular deep brain stimulation towards LGN
neuron is performed. A reduced dendrite structure was used in the
model using Bush–Sejnowski algorithm to decrease the
computational time while conserving its input resistance and total
surface area. The major finding is that an input potential of 0.4 V is
required to produce the action potential in the LGN neuron which is
placed at 100 μm distance from the electrode. From this study, it can
be concluded that the neuroprostheses under design would need to
consider the capability of inducing at least 0.4V to produce action
potentials in LGN.
Abstract: Lateral torsional buckling is a global buckling mode
which should be considered in design of slender structural members
under flexure about their strong axis. It is possible to compute the
load which causes lateral torsional buckling of a beam by finite
element analysis, however, closed form equations are needed in
engineering practice for calculation ease which can be obtained by
using energy method. In lateral torsional buckling applications of
energy method, a proper function for the critical lateral torsional
buckling mode should be chosen which can be thought as the
variation of twisting angle along the buckled beam. Accuracy of the
results depends on how close is the chosen function to the exact
mode. Since critical lateral torsional buckling mode of the cantilever
I-beams varies due to material properties, section properties and
loading case, the hardest step is to determine a proper mode function
in application of energy method. This paper presents an approximate function for critical lateral
torsional buckling mode of doubly symmetric cantilever I-beams.
Coefficient matrices are calculated for concentrated load at free end,
uniformly distributed load and constant moment along the beam
cases. Critical lateral torsional buckling modes obtained by presented
function and exact solutions are compared. It is found that the modes
obtained by presented function coincide with differential equation
solutions for considered loading cases.
Abstract: In this study, a general approach to the reliability
based limit analysis of laterally loaded piles is presented. In
engineering practice the uncertainties play a very important role. The
aim of this study is to evaluate the lateral load capacity of free-head
and fixed-head long pile when plastic limit analysis is considered. In
addition to the plastic limit analysis to control the plastic behaviour
of the structure, uncertain bound on the complementary strain energy
of the residual forces is also applied. This bound has significant effect
for the load parameter. The solution to reliability-based problems is
obtained by a computer program which is governed by the reliability
index calculation.
Abstract: The paper aims at investigating the effect of number
of story on different structural components of reinforced concrete
building due to gravity and lateral loading. For the study, three
building models having same building plan of three, six and nine
stories are analyzed and designed using software package. All the
buildings are residential and are located in Dhaka city of Bangladesh.
Lateral load including wind and earthquake loading are applied to the
building along both longitudinal and transverse direction as per
Bangladesh National Building Code (BNBC, 2006). Equivalent static
force method is followed for the applied seismic loading. The present
study investigates as well as compares mainly total steel requirement
in different structural components for those buildings. It has been
found that total longitudinal steel requirement for beams at each floor
is 48.57% for three storied building, 61.36% for six storied building
when the total percentage is taken as 100% in case of nine storied
building. For an exterior column, the steel ratio is 2.1%, 3.06%,
4.55% for three, six and nine storied building respectively for the first
three floors. In addition, it has been noted that total weight of
longitudinal reinforcement of an interior column is 14.02 % for threestoried
building and 43.12% for six storied building when the total
reinforcement is considered 100% for nine storied building for the
first three floors.
Abstract: Environmental and functional conditions, sometimes,
necessitate the architectural plan of the building to be asymmetric,
and this result in an asymmetric structure. In such cases finding an
optimal pattern for locating the components of lateral load bearing
system, including shear walls, in the building’s plan is desired. In
case of shear wall in addition to the location the shape of the wall
cross-section is also an effective factor. Various types of shear walls
and their proper layout might come effective in better stiffness
distribution and more appropriate seismic response of the building.
Several studies have been conducted in the context of analysis and
design of shear walls; however, few studies have been performed on
making decisions for the location and form of shear walls in multistory
buildings, especially those with irregular plan. In this study, an
attempt has been made to obtain the most reliable seismic behavior of
multi-story reinforced concrete vertically chamfered buildings by
using more appropriate shear walls form and arrangement in 7-, 10-,
12-, and 15-stoy buildings. The considered forms and arrangements
include common rectangular walls and L-, T-, U- and Z-shaped plan,
located as the core or in the outer frames of the building structure.
Comparison of seismic behaviors of the buildings, including
maximum roof displacement and particularly formation of plastic
hinges and their distribution in the buildings’ structures, have been
done based on the results of a series of nonlinear time history
analyses, by using a set of selected earthquake records. Results show
that shear walls with U-shaped cross-section, placed as the building
central core, and also walls with Z-shaped cross-section, placed at the
corners give the building more reliable seismic behavior.
Abstract: For a rigid body sliding on a rough surface, a range of
uncertainty or non-uniqueness of solution could be found, which is
termed: Painlevé paradox. Painlevé paradox is the reason of a wide
range of bouncing motion, observed during sliding of robotic
manipulators on rough surfaces. In this research work, the existence
of the paradox zone during the sliding motion of a two-link (P-R)
robotic manipulator with a unilateral constraint is investigated.
Parametric study is performed to investigate the effect of friction,
link-length ratio, total height and link-mass ratio on the paradox zone.
Abstract: Twin steel plates-concrete composite shear walls are
composed of a pair of steel plate layers and a concrete layer
sandwiched between them, which have the characteristics of both
reinforced concrete shear walls and steel plate shear walls. Twin steel
plates-composite shear walls contain very high ultimsate bearing
capacity and ductility, which have great potential to be applied in the
super high-rise buildings and special structures. In this paper, we
analyzed the basic characteristics and stress mechanism of the twin
steel plates-composite shear walls. Specifically, we analyzed the
effects of the steel plate thickness, wall thickness and concrete
strength on the bearing capacity of the twin steel plates-composite
shear walls. The analysis results indicate that: (1) the initial shear
stiffness and ultimate shear-carrying capacity is not significantly
affected by the thickness of concrete wall but by the class of concrete,
(2) both factors significantly impact the shear distribution of the
shear walls in ultimate shear-carrying capacity. The technique of twin
steel plates-composite shear walls has been successfully applied in
the construction of an 88-meter Huge Statue of Buddha located in
Hunan Province, China. The analysis results and engineering
experiences showed that the twin steel plates-composite shear walls
have great potential for future research and applications.