Abstract: The detection of the polymer melt state during
manufacture process is regarded as an efficient way to control the
molded part quality in advance. Online monitoring rheological
property of polymer melt during processing procedure provides an
approach to understand the melt state immediately. Rheological
property reflects the polymer melt state at different processing
parameters and is very important in injection molding process
especially. An approach that demonstrates how to calculate
rheological property of polymer melt through in-process
measurement, using injection molding as an example, is proposed in
this study. The system consists of two sensors and a data acquisition
module can process the measured data, which are used for the
calculation of rheological properties of polymer melt. The rheological
properties of polymer melt discussed in this study include shear rate
and viscosity which are investigated with respect to injection speed
and melt temperature. The results show that the effect of injection
speed on the rheological properties is apparent, especially for high
melt temperature and should be considered for precision molding
process.
Abstract: In this study, composites were fabricated from oil
palm empty fruit bunch fiber and poly(lactic) acid by extrusion
followed by injection moulding. Surface of the fiber was pre-treated
by ultrasound in an alkali medium and treatment efficiency was
investigated by scanning electron microscopy (SEM) analysis and
Fourier transforms infrared spectrometer (FTIR). Effect of fiber
treatment on composite was characterized by tensile strength (TS),
tensile modulus (TM) and impact strength (IS). Furthermore,
biostrong impact modifier was incorporated into the treated fiber
composite to improve its impact properties. Mechanical testing
showed an improvement of up to 23.5% and 33.6% respectively for
TS and TM of treated fiber composite above untreated fiber
composite. On the other hand incorporation of impact modifier led to
enhancement of about 20% above the initial IS of the treated fiber
composite.
Abstract: It has experimentally been proved that the
performance of compression ignition (C.I.) engine is spray
characteristics related. In modern diesel engine the spray formation
and the eventual combustion process are the vital processes that offer
more challenges towards enhancing the engine performance. In the
present work the numerical simulation has been carried out for
evaporating diesel sprays using Fluent software. For computational
fluid dynamics simulation “Meshing” is done using Gambit software
before transmitting it into Fluent. The simulation is carried out using
hot bomb conditions under varying chamber conditions such as gas
pressure, nozzle diameter and fuel injection pressure. For comparison
purpose, the numerical simulations the chamber conditions were kept
the same as that of the experimental data. At varying chamber
conditions the spray penetration rates are compared with the existing
experimental results.
Abstract: Wet scrubbers have found widespread use in cleaning
contaminated gas streams because of their ability to remove
particulates and based on the applications of scrubbing of marine
engine exhaust gases by spraying sea-water. In order to examine the
flow characteristics inside the scrubber, the model is designated with
flow properties of hot air and water sprayer. The flow dynamics of
evaporation of hot air by the injection of water droplets is the key
factor considered in this paper. The flow behavior inside the scrubber
was investigated from the previous works and to sum up the
evaporation rate with respect to the concentration of water droplets are
predicted to bring out the competent modelling. The numerical
analysis using CFD facilitates in understanding the problem better and
empathies the behavior of the model over its entire operating envelope.
Abstract: Reburning is a useful technology in reducing nitric
oxide through injection of a secondary hydrocarbon fuel. In this paper,
an experimental study has been conducted to evaluate the effect of fuel
lean reburning on NOx/CO reduction in LNG flame. Experiments
were performed in flames stabilized by a co-flow swirl burner, which
was mounted at the bottom of the furnace. Tests were conducted using
LNG gas as the reburn fuel as well as the main fuel. The effects of
reburn fuel fraction and injection manner of the reburn fuel were
studied when the fuel lean reburning system was applied. The paper
reports data on flue gas emissions and temperature distribution in the
furnace for a wide range of experimental conditions. At steady state,
temperature distribution and emission formation in the furnace have
been measured and compared. This paper makes clear that in order to
decrease both NOx and CO concentrations in the exhaust when the
pulsated fuel lean reburning system was adapted, it is important that
the control of some factors such as frequency and duty ratio. Also it
shows the fuel lean reburning is also effective method to reduce NOx
as much as reburning.
Abstract: This paper presents the application of the Discrete
Component Model for heating and evaporation to multi-component
biodiesel fuel droplets in direct injection internal combustion engines.
This model takes into account the effects of temperature gradient,
recirculation and species diffusion inside droplets. A distinctive
feature of the model used in the analysis is that it is based on the
analytical solutions to the temperature and species diffusion
equations inside the droplets. Nineteen types of biodiesel fuels are
considered. It is shown that a simplistic model, based on the
approximation of biodiesel fuel by a single component or ignoring
the diffusion of components of biodiesel fuel, leads to noticeable
errors in predicted droplet evaporation time and time evolution of
droplet surface temperature and radius.
Abstract: This study presents a cost-effective approach for rapid
fabricating modeling platforms utilized in fused deposition modeling
system. A small-batch production of modeling platforms about 20
pieces can be obtained economically through silicone rubber mold
using vacuum casting without applying the plastic injection molding.
The air venting systems is crucial for fabricating modeling platform
using vacuum casting. Modeling platforms fabricated can be used for
building rapid prototyping model after sandblasting. This study offers
industrial value because it has both time-effectiveness and
cost-effectiveness.
Abstract: The knowledge of biodiesel density over large ranges
of temperature and pressure is important for predicting the behavior
of fuel injection and combustion systems in diesel engines, and for
the optimization of such systems. In this study, cottonseed oil was
transesterified into biodiesel and its density was measured at
temperatures between 288 K and 358 K and pressures between 0.1
MPa and 30 MPa, with expanded uncertainty estimated as ±1.6 kg⋅m-
3. Experimental pressure-volume-temperature (pVT) cottonseed data
was used along with literature data relative to other 18 biodiesels, in
order to build a database used to test the correlation of density with
temperarure and pressure using the Goharshadi–Morsali–Abbaspour
equation of state (GMA EoS). To our knowledge, this is the first that
density measurements are presented for cottonseed biodiesel under
such high pressures, and the GMA EoS used to model biodiesel
density. The new tested EoS allowed correlations within 0.2 kg·m-3
corresponding to average relative deviations within 0.02%. The built
database was used to develop and test a new full predictive model
derived from the observed linear relation between density and degree
of unsaturation (DU), which depended from biodiesel FAMEs
profile. The average density deviation of this method was only about
3 kg.m-3 within the temperature and pressure limits of application.
These results represent appreciable improvements in the context of
density prediction at high pressure when compared with other
equations of state.
Abstract: The cooling channels of injection mould play a crucial
role in determining the productivity of moulding process and the
product quality. It’s not a simple task to design high quality cooling
channels. In this paper, an intelligent cooling channels design system
including automatic layout of cooling channels, interference checking
and assembly of accessories is studied. Automatic layout of cooling
channels using genetic algorithm is analyzed. Through integrating
experience criteria of designing cooling channels, considering the
factors such as the mould temperature and interference checking, the
automatic layout of cooling channels is implemented. The method of
checking interference based on distance constraint algorithm and the
function of automatic and continuous assembly of accessories are
developed and integrated into the system. Case studies demonstrate the
feasibility and practicality of the intelligent design system.
Abstract: A method which allows a diabetic quadriplegic patient
that has had four limb amputations (above the knee and elbow) to
self-administer injections of insulin has been designed. The aim of
this research project is to improve a quadriplegic patient’s selfmanagement,
affected by diabetes, by designing a suitable device for
self-administering insulin.
The quadriplegic patient affected by diabetes has to be able to selfadminister
insulin safely and independently to guarantee stable
healthy conditions. The device also should be designed to adapt to a
number of different varying personal characteristics such as height
and body weight.
Abstract: Voltage sags are the most common power quality
disturbance in the distribution system. It occurs due to the fault in the
electrical network or by the starting of a large induction motor and
this can be solved by using the custom power devices such as
Dynamic Voltage Restorer (DVR). In this paper DVR is proposed to
compensate voltage sags on critical loads dynamically. The DVR
consists of VSC, injection transformers, passive filters and energy
storage (lead acid battery). By injecting an appropriate voltage, the
DVR restores a voltage waveform and ensures constant load voltage.
The simulation and experimental results of a DVR using MATLAB
software shows clearly the performance of the DVR in mitigating
voltage sags.
Abstract: This study models the use of transcutaneous electrical
nerve stimulation on skin with a disk electrode in order to simulate
tissue damage. The current density distribution above a disk electrode
is known to be a dynamic and non-uniform quantity that is intensified
at the edges of the disk. The non-uniformity is subject to change
through using various electrode geometries or stimulation methods.
One of these methods known as edge-retarded stimulation has shown
to reduce this edge enhancement. Though progress has been made in
modeling the behavior of a disk electrode, little has been done to test
the validity of these models in simulating the actual heat transfer
from the electrode. This simulation uses finite element software to
couple the injection of current from a disk electrode to heat transfer
described by the Pennesbioheat transfer equation. An example
application of this model is studying an experimental form of
stimulation, known as edge-retarded stimulation. The edge-retarded
stimulation method will reduce the current density at the edges of the
electrode. It is hypothesized that reducing the current density edge
enhancement effect will, in turn, reduce temperature change and
tissue damage at the edges of these electrodes. This study tests this
hypothesis as a demonstration of the capabilities of this model. The
edge-retarded stimulation proved to be safer after this simulation. It is
shown that temperature change and the fraction of tissue necrosis is
much greater in the square wave stimulation. These results bring
implications for changes of procedures in transcutaneous electrical
nerve stimulation and transcutaneous spinal cord stimulation as well.
Abstract: Azadirachta excelsa or locally known as sentang are
frequently used as a traditional medicine by diabetes patients in
Malaysia. However, less attention has been given to their toxicity
effect. Thus, the study is an attempt to examine the protective effect
of A. excelsa on the pancreas and to determine possible toxicity
mediated by the extract. Diabetes was induced experimentally in rats
by high-fat-diet for 16 weeks followed by intraperitoneal injection of
streptozotocin at dosage of 35 mg/kg of body weight. Declination of
the fasting blood glucose level was observed after continuous
administration of A. excelsa for 14 days twice daily. This is due to the
refining structure of the pancreas. However, surprisingly, the plant
extract reduced the leukocytes, erythrocytes, hemoglobin, MCHC and
lymphocytes. In addition, the rat treated with the plant extract
exhibited increment in AST and eosinocytes level. Overall, the
finding shows that A. excelsa possesses antidiabetic activity by
improving the structure of pancreatic islet of Langerhans but
involved in ameliorating of hematology and biochemical parameters.
Abstract: Because of high thermal efficiency and low CO2
emission, diesel engines are being used widely in many industrial
fields although it makes many PM and NOx which give both human
health and environment a negative effect. NOx regulations for diesel
engines, however, are being strengthened and it is impossible to meet
the emission standard without NOx reduction devices such as SCR
(Selective Catalytic Reduction), LNC (Lean NOx Catalyst), and LNT
(Lean NOx Trap). Among the NOx reduction devices, urea-SCR
system is known as the most stable and efficient method to solve the
problem of NOx emission. But this device has some issues associated
with the ammonia slip phenomenon which is occurred by shortage of
evaporation and thermolysis time, and that makes it difficult to achieve
uniform distribution of the injected urea in front of monolith.
Therefore, this study has focused on the mixing enhancement between
urea and exhaust gases to enhance the efficiency of the SCR catalyst
equipped in catalytic muffler by changing inlet gas temperature and
spray conditions to improve the spray uniformity of the urea water
solution. Finally, it can be found that various parameters such as inlet
gas temperature and injector and injection angles significantly affect
the evaporation and mixing of the urea water solution with exhaust
gases, and therefore, optimization of these parameters are required.
Abstract: The protective effect of hesperidin was investigated in
rats exposed to liver injury induced by a single intraperitoneal
injection of cyclophosphamide (CYP) at a dose of 150 mg kg-1.
Hesperidin treatment (100 mg kg-1/day, orally) was applied for seven
days, starting five days before CYP administration. Hesperidin
significantly decreased the CYP-induced elevations of serum alanine
aminotransferase, and hepatic malondialdehyde and myeloperoxidase
activity, significantly prevented the depletion of hepatic glutathione
peroxidase activity resulted from CYP administration. Also,
hesperidin ameliorated the CYP-induced liver tissue injury observed
by histopathological examination. In addition, hesperidin decreased
the CYP-induced expression of inducible nitric oxide synthase, tumor
necrosis factor-α, cyclooxygenase-2, Fas ligand, and caspase-9 in
liver tissue. It was concluded that hesperidin may represent a
potential candidate to protect against CYP-induced hepatotoxicity.
Abstract: A novel technique has been developed to generate ultra-stable millimeter-wave signal by optical heterodyning of the output from two slave laser (SL) sources injection-locked to the sidebands of a frequency modulated (FM) master laser (ML). Precise thermal tuning of the SL sources is required to lock the particular slave laser frequency to the desired FM sidebands of the ML. The output signals from the injection-locked SL when coherently heterodyned in a fast response photo detector like high electron mobility transistor (HEMT), extremely stable millimeter-wave signal having very narrow line width can be generated. The scheme may also be used to generate ultra-stable sub-millimeter-wave/terahertz signal.
Abstract: We have developed a polyimide based neural interface electrode to record nerve signals from the sciatic nerve of a rat. The neural interface electrode has a split-ring shape, with four protruding gold electrodes for recording, and two reference gold electrodes around the split-ring. The split-ring electrode can be opened up to encircle the sciatic nerve. The four electrodes can be bent to sit on top of the nerve and hold the device in position, while the split-ring frame remains flat. In comparison, while traditional cuff electrodes can only fit certain sizes of the nerve, the developed device can fit a variety of rat sciatic nerve dimensions from 0.6 mm to 1.0 mm, and adapt to the chronic changes in the nerve as the electrode tips are bendable. The electrochemical impedance spectroscopy measurement was conducted. The gold electrode impedance is on the order of 10 kΩ, showing excellent charge injection capacity to record neural signals.
Abstract: Tensile specimens of nonflammable AZ91D Mg alloy were fabricated in this study via cold chamber die-casting process. Dimensions of tensile specimens were 25mm in length, 4mm in width, and 0.8 or 3.0mm in thickness. Microstructure observation was conducted before and after tensile tests at room temperature. In the die casting process, various injection distances from 150 to 260mm were employed to obtain optimum process conditions. Distribution of Al12Mg17 phase was the key factor to determine the mechanical properties of die-cast Mg alloy. Specimens with 3mm of thickness showed superior mechanical properties to those with 0.8mm of thickness. Closed networking of Al12Mg17 phase along grain boundary was found to be detrimental to mechanical properties of die-cast Mg alloy.
Abstract: Cesiumiodide with Na doping (CsI(Na)) solution or melt is easily forming three- dimension dendrites on the free surface. The defects or bobbles form inside the CsI(Na) during the solution or melt solidification. The defects or bobbles can further effect the x-ray path in the CsI(Na) crystal and decrease the scintillation characteristics of CsI(Na). In order to enhance the CsI(Na) scintillated property we made single crystal of CsI(Na) column in the anodic aluminum oxide (AAO) template by hydraulic pressure injection method. It is interesting that when CsI(Na) melt is confined in the small AAO channels, the column grow as stable single column without any dendrites. The high aspect ratio (100~10000) of AAO and nano to sub-micron channel structure which is a suitable template for single of crystal CsI(Na) formation. In this work, a new low-cost approach to fabricate scintillator crystals using anodic aluminum oxide (AAO) rather than Si is reported, which can produce scintillator crystals with a wide range of controllable size to optimize their performance in X-ray detection.
Abstract: The use of herbs to treat disease is accompanied with the history of human life. This research is aimed to study the anti-inflammatory and antinociceptive effects of hydroalcoholic extract of aerial parts of "Tanacetum balsamita balsamita". In the experimental studies 144 male mice are used. In the inflammatory test, animals were divided into six groups: Control, positive control (receiving Dexamethason at dose of 15mg/kg), and four experimental groups receiving Tanacetum balsamita balsamita hydroalcoholic extract at doses of 25, 50, 100 and 200mg/kg. Xylene was used to induce inflammation. Formalin was used to study the nociceptive effects. Animals were divided into six groups: control group, positive control group (receiving morphine) and four experimental groups receiving Tanacetum balsamita balsamita (Tb.) hydroalcoholic extract at doses of 25, 50, 100 and 200mg/kg. I.p. injection of drugs or normal saline was performed 30 minutes before test. The data were analyzed by using one way Variance analysis and Tukey post test. Aerial parts of Tanacetum balsamita balsamita hydroalcoholic extract decreased significantly inflammatory at dose of 200mg/kg (P