Abstract: A zero dimensional model has been used to investigate
the combustion performance of a single cylinder direct injection
diesel engine fueled by biofuels with options like supercharging and
exhaust gas recirculation. The numerical simulation was performed at
constant speed. The indicated pressure, temperature diagrams are
plotted and compared for different fuels. The emissions of soot and
nitrous oxide are computed with phenomenological models. The
experimental work was also carried out with biodiesel (palm stearin
methyl ester) diesel blends, ethanol diesel blends to validate
simulation results with experimental results, and observed that the
present model is successful in predicting the engine performance with
biofuels.
Abstract: A behavioral model of a second order switchedcapacitor Sigma-Delta modulator is presented. The purpose of this work is the presentation of a behavioral model of a second order switched capacitor ΣΔ modulator considering (Error due to Clock Jitter, Thermal noise Amplifier Noise, Amplifier Slew-Rate, Non linearity of amplifiers, Gain error, Charge Injection, Clock Feedthrough, and Nonlinear on-resistance). A comparison between the use of MOS switches and the use transmission gate switches use is analyzed.
Abstract: A design flow of multi-standard down-conversion
CMOS mixers for three modern standards: Global System Mobile,
Digital Enhanced Cordless Telephone and Universal Mobile
Telecommunication Systems is presented. Three active mixer-s
structures are studied. The first is based on the Gilbert cell which
gives a tolerable noise figure and linearity with a low conversion
gain. The second and third structures use the current bleeding and
charge injection techniques in order to increase the conversion gain.
An improvement of about 2 dB of the conversion gain is achieved
without a considerable degradation of the other characteristics. The
models used for noise figure, conversion gain and IIP3 used are
studied. This study describes the nature of trade-offs inherent in such
structures and gives insights that help in identifying which structure
is better for given conditions.
Abstract: The estrus female Etawah cross bred goats were
synchronized estrus by controlled internal drug release (CIDR)
implants for 10 days combined with PGF2α injection, and continued
by artificial insemination (AI) within the hours of 24 period. Vaginal
epithelium was taken to determine estrus cycle of the goats without
estrus synchronization. The estrus responds (the puffy of vulva and
vaginal pH) and percentage of pregnancy were investigated. The data
were analyzed descriptively and Independent Sample T-Test. The
results showed that the puffy of vulva and vaginal pH were
significantly different in synchronized estrus goats and control goats
(2.18 ± 0.33 cm vs. 1.20 ± 0.16 cm and 8.55 ± 0.63 vs. 8.22 ± 0.22).
Percentage of pregnancy was higher in synchronized estrus goats
(73.33%) than in control (53.3%). Estrus synchronization by using
CIDR implants and PGF2, continued by AI was effective to improve
reproduction performance of Etawah cross bred goats.
Abstract: In recent years with the rapid development of Internet and the Web, more and more web applications have been deployed in many fields and organizations such as finance, military, and government. Together with that, hackers have found more subtle ways to attack web applications. According to international statistics, SQL Injection is one of the most popular vulnerabilities of web applications. The consequences of this type of attacks are quite dangerous, such as sensitive information could be stolen or authentication systems might be by-passed. To mitigate the situation, several techniques have been adopted. In this research, a security solution is proposed using Artificial Neural Network to protect web applications against this type of attacks. The solution has been experimented on sample datasets and has given promising result. The solution has also been developed in a prototypic web application firewall called ANNbWAF.
Abstract: Since injection engines have a considerable portion, in
consumption of energy and environmental pollution, using an
alternative source of energy with lower pollutant effects in this
regard is necessary.
Biodiesel fuel is a suitable alternative for gasoline in diesel
engines.
In this research the property of biodiesel, the function and the
pollution effects of diesel engine, when using 100% biodiesel, using
100% gasoline and mixing ratio of both fuels for comparing them,
have been investigated.
The researches have shown, using biodiesel fuel in prevalent
diesel engine, will reduce the pollutants such as Co, half burned
carbohydrate and suspended particles and a little increase in
oxidation will achieve while power consumption, particularly fuel
and thermal efficiency of diesel fuel has the same.
Abstract: Due to the stringent legislation for emission of diesel
engines and also increasing demand on fuel consumption, the
importance of detailed 3D simulation of fuel injection, mixing and
combustion have been increased in the recent years. In the present
work, FIRE code has been used to study the detailed modeling of
spray and mixture formation in a Caterpillar heavy-duty diesel
engine. The paper provides an overview of the submodels
implemented, which account for liquid spray atomization, droplet
secondary break-up, droplet collision, impingement, turbulent
dispersion and evaporation. The simulation was performed from
intake valve closing (IVC) to exhaust valve opening (EVO). The
predicted in-cylinder pressure is validated by comparing with
existing experimental data. A good agreement between the predicted
and experimental values ensures the accuracy of the numerical
predictions collected with the present work. Predictions of engine
emissions were also performed and a good quantitative agreement
between measured and predicted NOx and soot emission data were
obtained with the use of the present Zeldowich mechanism and
Hiroyasu model. In addition, the results reported in this paper
illustrate that the numerical simulation can be one of the most
powerful and beneficial tools for the internal combustion engine
design, optimization and performance analysis.
Abstract: The Inter feeder Power Flow Regulator (IFPFR)
proposed in this paper consists of several voltage source inverters
with common dc bus; each inverter is connected in series with one of
different independent distribution feeders in the power system. This
paper is concerned with how to transfer power between the feeders for
load sharing purpose. The power controller of each inverter injects
the power (for sending feeder) or absorbs the power (for receiving
feeder) via injecting suitable voltage; this voltage injection is
simulated by voltage drop across series virtual impedance, the
impedance value is selected to achieve the concept of power exchange
between the feeders without perturbing the load voltage magnitude of
each feeder. In this paper a new control scheme for load sharing using
IFPFR is proposed.
Abstract: Recently, the advanced technologies that offer high
precision product, relative easy, economical process and also rapid
production are needed to realize the high demand of ultra precision
micro part. In our research, micromanufacturing based on soft
lithography and nanopowder injection molding was investigated. The
silicone metal pattern with ultra thick and high aspect ratio succeeds to
fabricate Polydimethylsiloxane (PDMS) micro mold. The process
followed by nanopowder injection molding (PIM) by a simple vacuum
hot press. The 17-4ph nanopowder with diameter of 100 nm, succeed
to be injected and it forms green sample microbearing with thickness,
microchannel and aspect ratio is 700μm, 60μm and 12, respectively.
Sintering process was done in 1200 C for 2 hours and heating rate
0.83oC/min. Since low powder load (45% PL) was applied to achieve
green sample fabrication, ~15% shrinkage happen in the 86% relative
density. Several improvements should be done to produce high
accuracy and full density sintered part.
Abstract: Fecal sterol has been proposed as a chemical indicator
of human fecal pollution even when fecal coliform populations have
diminished due to water chlorination or toxic effects of industrial
effluents. This paper describes an improved derivatization procedure
for simultaneous determination of four fecal sterols including
coprostanol, epicholestanol, cholesterol and cholestanol using gas
chromatography-mass spectrometry (GC-MS), via optimization study
on silylation procedures using N-O-bis
(trimethylsilyl)-trifluoroacetamide (BSTFA), and
N-(tert-butyldimethylsilyl)-N-methyltrifluoroacetamide
(MTBSTFA), which lead to the formation of trimethylsilyl (TMS) and
tert-butyldimethylsilyl (TBS) derivatives, respectively. Two
derivatization processes of injection-port derivatization and water bath
derivatization (60 oC, 1h) were inspected and compared. Furthermore,
the methylation procedure at 25 oC for 2h with
trimethylsilydiazomethane (TMSD) for fecal sterols analysis was also
studied. It was found that most of TMS derivatives demonstrated the
highest sensitivities, followed by methylated derivatives. For BSTFA
or MTBSTFA derivatization processes, the simple injection-port
derivatization process could achieve the same efficiency as that in the
tedious water bath derivatization procedure.
Abstract: Computers are being integrated in the various aspects
of human every day life in different shapes and abilities. This fact
has intensified a requirement for the software development
technologies which is ability to be: 1) portable, 2) adaptable, and 3)
simple to develop. This problem is also known as the Pervasive
Computing Problem (PCP) which can be implemented in different
ways, each has its own pros and cons and Context Oriented
Programming (COP) is one of the methods to address the PCP.
In this paper a design for a COP framework, a context aware
framework, is presented which has eliminated weak points of a
previous design based on interpreter languages, while introducing the
compiler languages power in implementing these frameworks.
The key point of this improvement is combining COP and
Dependency Injection (DI) techniques. Both old and new frameworks
are analyzed to show advantages and disadvantages. Finally a
simulation of both designs is proposed to indicating that the practical
results agree with the theoretical analysis while the new design runs
almost 8 times faster.
Abstract: Intravitreal injection (IVI) is the most common treatment for eye posterior segment diseases such as endopthalmitis, retinitis, age-related macular degeneration, diabetic retinopathy, uveitis, and retinal detachment. Most of the drugs used to treat vitreoretinal diseases, have a narrow concentration range in which they are effective, and may be toxic at higher concentrations. Therefore, it is critical to know the drug distribution within the eye following intravitreal injection. Having knowledge of drug distribution, ophthalmologists can decide on drug injection frequency while minimizing damage to tissues. The goal of this study was to develop a computer model to predict intraocular concentrations and pharmacokinetics of intravitreally injected drugs. A finite volume model was created to predict distribution of two drugs with different physiochemical properties in the rabbit eye. The model parameters were obtained from literature review. To validate this numeric model, the in vivo data of spatial concentration profile from the lens to the retina were compared with the numeric data. The difference was less than 5% between the numerical and experimental data. This validation provides strong support for the numerical methodology and associated assumptions of the current study.
Abstract: Although lots of experiments have been done in enhanced oil recovery, the number of experiments which consider the effects of local and global heterogeneity on efficiency of enhanced oil recovery based on the polymer-surfactant flooding is low and rarely done. In this research, we have done numerous experiments of water flooding and polymer-surfactant flooding on a five spot glass micromodel in different conditions such as different positions of layers. In these experiments, five different micromodels with three different pore structures are designed. Three models with different layer orientation, one homogenous model and one heterogeneous model are designed. In order to import the effect of heterogeneity of porous media, three types of pore structures are distributed accidentally and with equal ratio throughout heterogeneous micromodel network according to random normal distribution. The results show that maximum EOR recovery factor will happen in a situation where the layers are orthogonal to the path of mainstream and the minimum EOR recovery factor will happen in a situation where the model is heterogeneous. This experiments show that in polymer-surfactant flooding, with increase of angles of layers the EOR recovery factor will increase and this recovery factor is strongly affected by local heterogeneity around the injection zone.