Abstract: Homogeneous composites of alumina and zirconia
with a small amount of MgO (99%) were obtained for ZTA ceramic containing 0.05 wt% MgO in
1500 °C.
Abstract: In this paper, free vibration analysis of carbon nanotube (CNT) reinforced laminated composite panels is presented. Three types of panels such as flat, concave and convex are considered for study. Numerical simulation is carried out using commercially available finite element analysis software ANSYS. Numerical homogenization is employed to calculate the effective elastic properties of randomly distributed carbon nanotube reinforced composites. To verify the accuracy of the finite element method, comparisons are made with existing results available in the literature for conventional laminated composite panels and good agreements are obtained. The results of the CNT reinforced composite materials are compared with conventional composite materials under different boundary conditions.
Abstract: Metal matrix composites (MMC) are generating
extensive interest in diverse fields like defense, aerospace, electronics
and automotive industries. In this present investigation, material
removal rate (MRR) modeling has been carried out using an
axisymmetric model of Al-SiC composite during electrical discharge
machining (EDM). A FEA model of single spark EDM was
developed to calculate the temperature distribution.Further, single
spark model was extended to simulate the second discharge. For
multi-discharge machining material removal was calculated by
calculating the number of pulses. Validation of model has been done
by comparing the experimental results obtained under the same
process parameters with the analytical results. A good agreement was
found between the experimental results and the theoretical value.
Abstract: Magnetic carbon nanotubes composites were obtained
by filling carbon nanotubes with paramagnetic iron oxide particles.
Detailed investigation of magnetic behaviour of resulting composites
was done at different temperatures. Measurements indicate that these
functionalized nanotubes are superparamagnetic at room temperature;
however, no superparamagnetism was observed at 125 K and 80 K.
The blocking temperature TB was estimated at 145 K. These magnetic
carbon nanotubes have the potential of being used in a wide range of
applications, in particular, the production of nanofluids, which can be
controlled and steered by appropriate magnetic fields.
Abstract: Carbon fibers have specific characteristics in
comparison with industrial and structural materials used in different
applications. Special properties of carbon fibers make them attractive
for reinforcing and fabrication of composites. These fibers have been
utilized for composites of metals, ceramics and plastics. However,
it-s mainly used in different forms to reinforce lightweight polymer
materials such as epoxy resin, polyesters or polyamides. The
composites of carbon fiber are stronger than steel, stiffer than
titanium, and lighter than aluminum and nowadays they are used in a
variety of applications. This study explains applications of carbon
fibers in different fields such as space, aviation, transportation,
medical, construction, energy, sporting goods, electronics, and the
other commercial/industrial applications. The last findings of
composites with polymer, metal and ceramic matrices containing
carbon fibers and their applications in the world investigated.
Researches show that carbon fibers-reinforced composites due to
unique properties (including high specific strength and specific
modulus, low thermal expansion coefficient, high fatigue strength,
and high thermal stability) can be replaced with common industrial
and structural materials.
Abstract: In this study, structural, mechanical, thermal and
electrical properties of poly (lactic acid) (PLA) nanocomposites with
low-loaded (0-1.5 wt%) untreated, heat and nitric acid treated multiwalled
carbon nanotubes (MWCNTs) were studied. Among the
composites, untreated 0.5 wt % MWCNTs and acid-treated 1.0 wt%
MWCNTs reinforced PLA show the tensile strength and modulus
values higher than the others. These two samples along with pure
PLA exhibit the stable orthorhombic α-form, whilst other samples
reveal the less stable orthorhombic β-form, as demonstrated by X-ray
diffraction study. Differential scanning calorimetry reveals the
evolution of the mentioned different phases by controlled cooling and
discloses an enhancement of PLA crystallization by nanotubes
incorporation. Thermogravimetric analysis shows that the MWCNTs
loaded sample degraded faster than PLA. Surface resistivity of the
nanocomposites is found to be dropped drastically by a factor of 1013
with a low loading of MWCNTs (1.5 wt%).
Abstract: This paper presents the results of thermo-mechanical
characterization of Glass/Epoxy composite specimens using Infrared
Thermography technique. The specimens used for the study were
fabricated in-house with three different lay-up sequences and tested
on a servo hydraulic machine under uni-axial loading. Infrared
Camera was used for on-line monitoring surface temperature changes
of composite specimens during tensile deformation.
Experimental results showed that thermomechanical
characteristics of each type of specimens were distinct. Temperature
was found to be decreasing linearly with increasing tensile stress in
the elastic region due to thermo-elastic effect. Yield point could be
observed by monitoring the change in temperature profile during
tensile testing and this value could be correlated with the results
obtained from stress-strain response. The extent of prior plastic
deformation in the post-yield region influenced the slopes of
temperature response during tensile loading. Partial unloading and
reloading of specimens post-yield results in change in slope in elastic
and plastic regions of composite specimens.
Abstract: Copper based composites reinforced with WC and Ti
particles were prepared using planetary ball-mill. The experiment
was designed by using Taguchi technique and milling was carried out
in an air for several hours. The powder was characterized before and
after milling using the SEM, TEM and X-ray for microstructure and
for possible new phases. Microstructures show that milled particles
size and reduction in particle size depend on many parameters. The
distance d between planes of atoms estimated from X-ray powder
diffraction data and TEM image. X-ray diffraction patterns of the
milled powder did not show clearly any new peak or energy shift, but
the TEM images show a significant change in crystalline structure of
corporate on titanium in the composites.
Abstract: Waste problem is becoming a future problem all over the world. Magnesium wastes which can be used in recycling processes are produced by many industrial activities. Magnesium borates which have useful properties such as; high heat resistance, corrosion resistance, supermechanical strength, superinsulation, light weight, high coefficient of elasticity and so on. Addition, magnesium borates have great potential in the development of ceramic and detergents industry, whisker-reinforced composites, antiwear, and reducing friction additives.
In this study, using the starting materials of waste magnesium and H3BO3 the hydrothermal method was applied at a moderate temperature of 70oC with different reaction times. Several reaction times of waste magnesium to H3BO3 were selected as; 30, 60, 120, 240 minutes. After the synthesis, X-Ray Diffraction (XRD) and Fourier Transform Infrared Spectroscopy (FT-IR) techniques were applied to products. As a result, the forms of Admontite [MgO(B2O3)3.7(H2O)] and Mcallisterite [Mg2(B6O7(OH)6)2.9(H2O)] were synthesized.
Abstract: Thermoplastic starch, polylactic acid glycerol and
maleic anhydride (MA) were compounded with natural
montmorillonite (MMT) through a twin screw extruder to investigate
the effects of different loading of MMT on structure, thermal and
absorption behavior of the nanocomposites. X-ray diffraction analysis
(XRD) showed that sample with MMT loading 4phr exhibited
exfoliated structure while sample that contained MMT 8 phr
exhibited intercalated structure. FESEM images showed big lump
when MMT loading was at 8 phr. The thermal properties were
characterized by using differential scanning calorimeter (DSC). The
results showed that MMT increased melting temperature and
crystallization temperature of matrix but reduction in glass transition
temperature was observed Meanwhile the addition of MMT has
improved the water barrier property. The nanosize MMT particle is
also able to block a tortuous pathway for water to enter the starch
chain, thus reducing the water uptake and improved the physical
barrier of nanocomposite.
Abstract: A two-parameter fatigue model explicitly accounting for the cyclic as well as the mean stress was used to fit static and fatigue data available in literature concerning carbon fiber reinforced composite laminates subjected tension-tension fatigue. The model confirms the strength–life equal rank assumption and predicts reasonably the probability of failure under cyclic loading. The model parameters were found by best fitting procedures and required a minimum of experimental tests.
Abstract: This paper presents the Literature Review of carbon fiber reinforced polymer (CFRP) strips to reinforced concrete (RC) as a strengthening solution for T-beams. Although a great deal of research has been carried out on Rectangular beams strengthened with Fibre-Reinforced Polymer composites (FRP), Fiber reinforced polymer (FRP) composites have been increasingly studied for their application in the flexural or shear strengthening of reinforced concrete (RC) members. A detailed discussion of the shearstrengthening repair with FRP is undertaken. This paper will be limited to research of CFRP material externally bonded to the tensile face of concrete beams. In particular, research studying the effect of externally applied CFRP materials on the shear performance of reinforced concrete beams will be reported.
Abstract: Metal matrix composites have been increasingly used
as materials for components in automotive and aerospace industries
because of their improved properties compared with non-reinforced
alloys. During machining the selection of appropriate machining
parameters to produce job for desired surface roughness is of great
concern considering the economy of manufacturing process. In this
study, a surface roughness prediction model using fuzzy logic is
developed for end milling of Al-SiCp metal matrix composite
component using carbide end mill cutter. The surface roughness is
modeled as a function of spindle speed (N), feed rate (f), depth of cut
(d) and the SiCp percentage (S). The predicted values surface
roughness is compared with experimental result. The model predicts
average percentage error as 4.56% and mean square error as 0.0729.
It is observed that surface roughness is most influenced by feed rate,
spindle speed and SiC percentage. Depth of cut has least influence.
Abstract: Materials added to the matrix help improving operating properties of a composite. This experimental study has targeted to investigate this aim where Silicon Oxide particles were added to glass fibre and epoxy resin at an amount of 15% to the main material to obtain a sort of new composite material. Erosive wear behavior of epoxy-resin dipped composite materials reinforced with glass fibre and Silicon Oxide under three different impingement angles (30°, 60° and 90°), three different impact velocities (23, 34 and 53 m/s), two different angular Aluminum abrasive particle sizes (approximately 200 and 400 μm) and the fibre orientation of 45° (45/-45) were investigated. In the test results, erosion rates were obtained as functions of impingement angles, impact velocities, particle sizes and fibre orientation. Moreover, materials with addition of Silicon Oxide filler material exhibited lower wear as compared to neat materials with no added filler material. In addition, SEM views showing worn out surfaces of the test specimens were scrutinized.
Abstract: Emphasis on the advancement of new materials and technology has been there for the past few decades. The global development towards using cheap and durable materials from renewable resources contributes to sustainable development. An experimental investigation of mechanical behaviour of sisal fibre-reinforced concrete is reported for making a suitable building material in terms of reinforcement. Fibre reinforced Composite is one such material, which has reformed the concept of high strength. Sisal fibres are abundantly available in the hot areas. Sisal fibre has emerged as a reinforcing material for concretes, used in civil structures. In this work, properties such as hardness and tensile strength of sisal fibre reinforced cement composites with 6, 12, 18 and 24% by weight of sisal fibres were assessed. Sisal fibre reinforced cement composite slabs with long sisal fibres were manufactured using a cast hand lay up technique. Mechanical response was measured under tension. The high energy absorption capacity of the developed composite system was reflected in high toughness values under tension respectively.
Abstract: Platinum oxide nanoparticles were prepared by a
simple hydrothermal route and chemical reduction using
carbohydrates (Fructose and sucrose) as the reducing and
stabilizing agents. The crystallite size of these nanoparticles was
evaluated from X-ray diffraction (XRD), atomic force microscopy
(AFM) and transmission electron microscopy (TEM) and was
found to be 10 nm as shown in figure 1, which is the
demonstration of EM bright field and transmission electron
microscopy. The effect of carbohydrates on the morphology of the
nanoparticles was studied using TEM (Figure 1). The
nanoparticles (100 μg/ml) were administered to the Pseudomonas
Stutzeri and Lactobacillus cultures and the incubation was done at
35 oC for 24 hours. The nanocomposites exhibited interesting
inhibitory as well as bactericidal activity against P. Stutzeri and
and Lactobacillus species. Incorporation of nanoparticles also
increased the thermal stability of the carbohydrates.
Abstract: This paper reports on the enhanced photoluminescence
(PL) of nanocomposites through the layered structuring of phosphor
and quantum dot (QD). Green phosphor of Sr2SiO4:Eu, red QDs of
CdSe/CdS/CdZnS/ZnS core-multishell, and thermo-curable resin
were used for this study. Two kinds of composite (layered and mixed)
were prepared, and the schemes for optical energy transfer between
QD and phosphor were suggested and investigated based on PL decay
characteristics. It was found that the layered structure is more effective
than the mixed one in the respects of PL intensity, PL decay and
thermal loss. When this layered nanocomposite (QDs on phosphor) is
used to make white light emitting diode (LED), the brightness is
increased by 37 %, and the color rendering index (CRI) value is raised
to 88.4 compared to the mixed case of 80.4.
Abstract: In the present study, the incorporation of graphene
into blends of acrylonitrile-butadiene-styrene terpolymer with
polypropylene (ABS/PP) was investigated focusing on the
improvement of their thermomechanical characteristics and the effect
on their rheological behavior. The blends were prepared by melt
mixing in a twin-screw extruder and were characterized by measuring
the MFI as well as by performing DSC, TGA and mechanical tests.
The addition of graphene to ABS/PP blends tends to increase their
melt viscosity, due to the confinement of polymer chains motion.
Also, graphene causes an increment of the crystallization temperature
(Tc), especially in blends with higher PP content, because of the
reduction of surface energy of PP nucleation, which is a consequence
of the attachment of PP chains to the surface of graphene through the
intermolecular CH-π interaction. Moreover, the above nanofiller
improves the thermal stability of PP and increases the residue of
thermal degradation at all the investigated compositions of blends,
due to the thermal isolation effect and the mass transport barrier
effect. Regarding the mechanical properties, the addition of graphene
improves the elastic modulus, because of its intrinsic mechanical
characteristics and its rigidity, and this effect is particularly strong in
the case of pure PP.
Abstract: Silver/polylactide nanocomposites (Ag/PLA-NCs) were
synthesized via chemical reduction method in diphase solvent. Silver
nitrate and sodium borohydride were used as a silver precursor
and reducing agent in the polylactide (PLA). The properties of
Ag/PLA-NCs were studied as a function of the weight percentages
of silver nanoparticles (8, 16 and 32 wt% of Ag-NPs) relative to
the weight of PLA. The Ag/PLA-NCs were characterized by Xray
diffraction (XRD), transmission electron microscopy (TEM),
electro-optical microscopy (EOM), UV-visible spectroscopy (UV-vis)
and Fourier transform infrared spectroscopy (FT-IR). XRD patterns
confirmed that Ag-NPs crystallographic planes were face centered
cubic (fcc) type. TEM images showed that mean diameters of Ag-NPs
were 3.30, 3.80 and 4.80 nm. Electro-optical microscopy revealed
excellent dispersion and interaction between Ag-NPs and PLA films.
The generation of silver nanoparticles was confirmed from the UVvisible
spectra. FT-IR spectra showed that there were no significant
differences between PLA and Ag/PLA-NCs films. The synthesized
Ag/PLA-NCs were stable in organic solution over a long period of
time without sign of precipitation.
Abstract: Alumina matrix composites with addition of hexagonal boron nitride (hBN), acting as solid lubricant, were produced. Main purpose of solid lubricants is to dispose the necessity of using cooling lubricants in machining process. Hot pressing was used as a consolidating process for Al2O3-x%wt.hBN (x=1/ 2,5/ 5 /7,5 /10) composites. Properties of sinters such as relative density, hardness, Young-s modulus and fracture toughness were examined. Obtained samples characterize by high relative density. Hardness and fracture toughness values allow the use of alumina – hBN composites for machining steels even in hardened condition. However it was observed that high weight content of hBN can negatively influence the mechanical properties of composites.