Abstract: Application of nanoparticles as additives in membrane
synthesis for improving the resistance of membranes against fouling
has triggered recent interest in new membrane types. However, most
nanoparticle-enhanced membranes suffer from the tradeoff between
permeability and selectivity. In this study, nano-WS2 was explored as
the additive in membrane synthesis by non-solvent induced phase
separation. Blended PES-WS2 flat-sheet membranes with the
incorporation of ultra-low concentrations of nanoparticles (from 0.025
to 0.25%, WS2/PES ratio) were manufactured and investigated in
terms of permeability, fouling resistance and solute rejection.
Remarkably, a significant enhancement in the permeability was
observed as a result of the incorporation of ultra-low fractions of
nano-WS2 to the membrane structure. Optimal permeability values
were obtained for modified membranes with 0.10%
nanoparticle/polymer concentration ratios. Furthermore, fouling
resistance and solute rejection were significantly improved by the
incorporation of nanoparticles into the membrane matrix. Specifically,
fouling resistance of modified membrane can increase by around 50%.
Abstract: This paper proposes the numerical simulation of the
investment casting of gold jewelry. It aims to study the behavior of
fluid flow during mould filling and solidification and to optimize the
process parameters, which lead to predict and control casting defects
such as gas porosity and shrinkage porosity. A finite difference
method, computer simulation software FLOW-3D was used to
simulate the jewelry casting process. The simplified model was
designed for both numerical simulation and real casting production.
A set of sensor acquisitions were allocated on the different positions
of the wax tree of the model to detect filling times, while a set of
thermocouples were allocated to detect the temperature during
casting and cooling. Those detected data were applied to validate the
results of the numerical simulation to the results of the real casting.
The resulting comparisons signify that the numerical simulation can
be used as an effective tool in investment-casting-process
optimization and casting-defect prediction.
Abstract: Droughts are complex, natural hazards that, to a
varying degree, affect some parts of the world every year. The range
of drought impacts is related to drought occurring in different stages
of the hydrological cycle and usually different types of droughts,
such as meteorological, agricultural, hydrological, and socioeconomical
are distinguished. Streamflow drought was analyzed by
the method of truncation level (at 70% level) on daily discharges
measured in 54 hydrometric stations in southwestern Iran. Frequency
analysis was carried out for annual maximum series (AMS) of
drought deficit volume and duration series. Some factors including
physiographic, climatic, geologic, and vegetation cover were studied
as influential factors in the regional analysis. According to the results
of factor analysis, six most effective factors were identified as area,
rainfall from December to February, the percent of area with
Normalized Difference Vegetation Index (NDVI)
Abstract: This work evaluated the effect of temperature on headspace solid-phase microextraction of volatile and furanic compounds in coated fish sticks. The major goal was the analysis of the samples as consumed, to reproduce volatile compounds people feel when consuming those products. Extraction at 37 ºC (the human body temperature) throughout the HS-SPME analysis of volatile and furanic compounds in coated fish was compared with higher extraction temperatures, which are frequently used for this kind of determinations. The profile of volatile compounds found in deepfried (F) and non-fried (NF) coated fish at 37 and 50 ºC was different from that obtained at 80 ºC. Concerning furan and its derivatives, an extra formation of these compounds was observed at higher extraction temperatures. The analysis of volatile and furanic compounds in fish coated sticks simulating the cooking and eating conditions can be reliably carried out setting the headspace absorption temperature at 37 ºC.
Abstract: Vehicle detection is the critical step for highway monitoring. In this paper we propose background subtraction and edge detection technique for vehicle detection. This technique uses the advantages of both approaches. The practical applications approved the effectiveness of this method. This method consists of two procedures: First, automatic background extraction procedure, in which the background is extracted automatically from the successive frames; Second vehicles detection procedure, which depend on edge detection and background subtraction. Experimental results show the effective application of this algorithm. Vehicles detection rate was higher than 91%.
Abstract: In this article, the phenomenon of nonlinear
consolidation in saturated and homogeneous clay layer is studied.
Considering time-varied drainage model, the excess pore water
pressure in the layer depth is calculated. The Generalized Differential
Quadrature (GDQ) method is used for the modeling and numerical
analysis. For the purpose of analysis, first the domain of independent
variables (i.e., time and clay layer depth) is discretized by the
Chebyshev-Gauss-Lobatto series and then the nonlinear system of
equations obtained from the GDQ method is solved by means of the
Newton-Raphson approach. The obtained results indicate that the
Generalized Differential Quadrature method, in addition to being
simple to apply, enjoys a very high accuracy in the calculation of
excess pore water pressure.
Abstract: Four design alternatives for lateral force-resisting
systems of tall buildings in Dubai, UAE are presented. Quantitative
comparisons between the different designs are also made. This paper
is intended to provide different feasible lateral systems to be used in
Dubai in light of the available seismic hazard studies of the UAE.
The different lateral systems are chosen in conformance with the
International Building Code (IBC). Moreover, the expected behavior
of each system is highlighted and light is shed on some of the cost
implications associated with lateral system selection.
Abstract: Rapid Prototyping (RP) is a technology that produces models and prototype parts from 3D CAD model data, CT/MRI scan data, and model data created from 3D object digitizing systems. There are several RP process like Stereolithography (SLA), Solid Ground Curing (SGC), Selective Laser Sintering (SLS), Fused Deposition Modeling (FDM), 3D Printing (3DP) among them SLS and FDM RP processes are used to fabricate pattern of custom cranial implant. RP technology is useful in engineering and biomedical application. This is helpful in engineering for product design, tooling and manufacture etc. RP biomedical applications are design and development of medical devices, instruments, prosthetics and implantation; it is also helpful in planning complex surgical operation. The traditional approach limits the full appreciation of various bony structure movements and therefore the custom implants produced are difficult to measure the anatomy of parts and analyze the changes in facial appearances accurately. Cranioplasty surgery is a surgical correction of a defect in cranial bone by implanting a metal or plastic replacement to restore the missing part. This paper aims to do a comparative study on the dimensional error of CAD and SLS RP Models for reconstruction of cranial defect by comparing the virtual CAD with the physical RP model of a cranial defect.
Abstract: Uterine and oviducal fluids are necessary for
capacitation of the spermatozoa and early embryonic development.
The aim of the present study was to determine the effects of estrous
cycle phases (follicular and luteal) on some biological parameters
(enzymes, electrolytes and total proteins) in uterine and oviducal
secretions of ewes. Oviducal and uterine fluids were collected,
diluted and centrifuged. According to our results, concentrations of
GPT, G6PDH, total proteins, K and Na were significantly (P
Abstract: Dynamic characteristics of a four-lobe journal bearing
of micropolar fluids are presented. Lubricating oil containing
additives and contaminants is modelled as micropolar fluid. The
modified Reynolds equation is obtained using the micropolar
lubrication theory and solving it by using finite difference technique.
The dynamic characteristics in terms of stiffness, damping
coefficients, the critical mass and whirl ratio are determined for
various values of size of material characteristic length and the
coupling number. The results show compared with Newtonian fluids,
that micropolar fluid exhibits better stability.
Abstract: Images are important in disease research, education,
and clinical medicine. This paper presents a Web Service Platform
(WSP) for support multiple programming languages to access image
from biomedical databases. The main function WSP is to allow web
users access image from biomedical databases. The WSP will
receive web user-s queries. After that, it will send to Querying
Server (QS) and the QS will search and retrieve data from
biomedical databases. Finally, the information will display to the
web users. Simple application is developed and tested for
experiment purpose. Result from experiment indicated WSP can be
used in biomedical environment.
Abstract: Managing knowledge of research is one way to ensure
just in time information and knowledge to support research strategist
and activities. Unfortunately researcher found the vital research
knowledge in IHL (Institutions of Higher Learning) are scattered,
unstructured and unorganized. Aiming on lay aside conceptual
foundations for understanding and developing OMS (Organizational
Memory System) to facilitate research in IHL, this research revealed
ten factors contributed to the needs of research in the IHL and seven
internal challenges of IHL in promoting research to their academic
members. This study then suggested a comprehensive support of
managing research knowledge using Organizational Memory System
(OMS). Eight OMS characteristics to support research were
identified. Finally the initial work in designing OMS was projected
using knowledge taxonomy. All analysis is derived from pertinent
research paper related to research in IHL and OMS. Further study can
be conducted to validate and verify results presented.
Abstract: Researches show that probability-statistical methods application, especially at the early stage of the aviation Gas Turbine Engine (GTE) technical condition diagnosing, when the flight information has property of the fuzzy, limitation and uncertainty is unfounded. Hence the efficiency of application of new technology Soft Computing at these diagnosing stages with the using of the Fuzzy Logic and Neural Networks methods is considered. According to the purpose of this problem training with high accuracy of fuzzy multiple linear and non-linear models (fuzzy regression equations) which received on the statistical fuzzy data basis is made. For GTE technical condition more adequate model making dynamics of skewness and kurtosis coefficients- changes are analysed. Researches of skewness and kurtosis coefficients values- changes show that, distributions of GTE workand output parameters of the multiple linear and non-linear generalised models at presence of noise measured (the new recursive Least Squares Method (LSM)). The developed GTE condition monitoring system provides stage-by-stage estimation of engine technical conditions. As application of the given technique the estimation of the new operating aviation engine technical condition was made.
Abstract: Software projects are very dynamic and require
recurring adjustments of their project plans. These settings can be
understood as reconfigurations in the schedule, in the resources
allocation and other design elements. Yet, during the planning and
execution of a software project, the integration of specific activities
in the projects with the activities that take part in the organization-s
common activity flow should be considered. This article presents the
results from a systematic review of aspects related to software
projects- dynamic reconfiguration emphasizing the integration of
project management with the organizational flows. A series of studies
was analyzed from the year 2000 to the present. The results of this
work show that there is a diversity of techniques and strategies for
dynamic reconfiguration of software projects-. However, few
approaches consider the integration of software project activities with
the activities that take part in the organization-s common workflow.
Abstract: Since prestressed concrete members rely on the tensile
strength of the prestressing strands to resist loads, loss of even few
them could result catastrophic. Therefore, it is important to measure
present residual prestress force. Although there are some techniques
for obtaining present prestress force, some problems still remain. One
method is to install load cell in front of anchor head but this may
increase cost. Load cell is a transducer using the elastic material
property. Anchor head is also an elastic material and this might result
in monitoring monitor present prestress force. Features of fiber optic
sensor such as small size, great sensitivity, high durability can assign
sensing function to anchor head. This paper presents the concept of
smart anchor head which acts as load cell and experiment for the
applicability of it. Test results showed the smart anchor head worked
good and strong linear relationship between load and response.
Abstract: A research program is conducted to evaluate the
mechanical properties of Ultra High Performance Concrete, target
compressive strength at the age of 28 days being more than 150 MPa.
The methodology to develop such mix has been explained. The
material properties, mix design and curing regime are determined.
The material attributes are understood by studying the stress strain
behaviour of UHPC cylinders under uniaxial compressive loading.
The load –crack mouth opening displacement (cmod) of UHPC
beams, flexural strength and fracture energy was evaluated using
third point loading test. Compressive strength and Split tensile
strength results are determined to find out the compressive and tensile
behaviour. Residual strength parameters are presented vividly
explaining the flexural performance, toughness of concrete.Durability
studies were also done to compare the effect of fibre to that of a
control mix For all the studies the Mechanical properties were
evaluated by varying the percentage and aspect ratio of steel fibres
The results reflected that higher aspect ratio and fibre volume
produced drastic changes in the cube strength, cylinder strength, post
peak response, load-cmod, fracture energy flexural strength, split
tensile strength, residual strength and durability. In regards to null
application of UHPC in India, an initiative is undertaken to
comprehend the mechanical behaviour of UHPC, which will be vital
for longer run in commercialization for structural applications.
Abstract: Online auctions are not very popular in Croatia. The
main reason for this is a very limited number of services which can
be used by Croatian users. Until recent times, even selling through
the most popular online auction site eBay wasn't possible because
PayPal services could not make payment to bank or debit card
accounts in Croatia. Furthermore, many foreign sellers do not offer
delivery of their products to Croatia which means that large
quantities of goods initially offered on such sites are not available.
With that in mind, it is necessary to analyze the buying and selling
habits of Croatian users and existing online auction sites, both
Croatian and foreign, and create a model for new domestic site. This
site will have to exploit every positive aspect of existing models and
neutralize every negative perception indicated by users in the survey
so that, hopefully, it would attract new users.
Abstract: Optimization study of the diesters biolubricant oleyl 9(12)-hydroxy-10(13)-oleioxy-12(9)-octadecanoate (OLHYOOT) was synthesized in the presence of sulfuric acid (SA) as catalyst has been done. Optimum conditions of the experiment to obtain high yield% of OLHYOOT were predicted at ratio of OL/HYOOA of 1:1 g/g, ratio of SA/HYOOA of 0.20:1 g/g, reaction temperature 110 °C and 4.5 h of reaction time. At this condition, the Yield% of OLHYOOT was 88.7. Disappearance of carboxylic acid (C=O) peak has observed by FTIR with appearance ester (C=O) at 1738 cm-1. 1H NMR spectra analyses confirmed the result of OLHYOOT with appearance ester (-CHOCOR) at 4.05ppm and also the 13C-NMR confirmed the result with appearance ester (C=O) peak at 173.93ppm.
Abstract: Liposomal magnetofection is the most powerful nonviral method for the nucleic acid delivery into the cultured cancer cells and widely used for in vitro applications. Use of the static magnetic field condition may result in non-uniform distribution of aggregate complexes on the surface of cultured cells. To prevent this, we developed the new device which allows to concentrate aggregate complexes under dynamic magnetic field, assisting more contact of these complexes with cellular membrane and, possibly, stimulating endocytosis. Newly developed device for magnetofection under dynamic gradient magnetic field, “DynaFECTOR", was used to compare transfection efficiency of human liver hepatocellular carcinoma cell line HepG2 with that obtained by lipofection and magnetofection. The effect of two parameters on transfection efficiency, incubation time under dynamic magnetic field and rotation frequency of magnet, was estimated. Liposomal magnetofection under dynamic gradient magnetic field showed the highest transfection efficiency for HepG2 cells.
Abstract: Knowledge Discovery in Databases (KDD) has
evolved into an important and active area of research because of
theoretical challenges and practical applications associated with the
problem of discovering (or extracting) interesting and previously
unknown knowledge from very large real-world databases. Rough
Set Theory (RST) is a mathematical formalism for representing
uncertainty that can be considered an extension of the classical set
theory. It has been used in many different research areas, including
those related to inductive machine learning and reduction of
knowledge in knowledge-based systems. One important concept
related to RST is that of a rough relation. In this paper we presented
the current status of research on applying rough set theory to KDD,
which will be helpful for handle the characteristics of real-world
databases. The main aim is to show how rough set and rough set
analysis can be effectively used to extract knowledge from large
databases.