Abstract: The major source of allergy in home is the house dust
mite (Dematophagoides farina, Dermatophagoides pteronyssinus)
causing allergic symptom include atopic dermatitis, asthma, perennial
rhinitis and even infant death syndrome.
Control of this mite species is dependent on the use of chemical
methods such as fumigation treatments with methylene bromide,
spraying with organophosphates such as pirimiphos-methyl, or
treatments with repellents such as DEET and benzyl benzoate.
Although effective, their repeated use for decades has sometimes
resulted in development of resistance and fostered environmental and
human health concerns. Both decomposing animal parts and the
protein that surrounds mite fecal pellets cause mite allergy. So it is
more effective to repel than to kill them because allergen is not living
house dust mite but dead body or fecal particles of house dust mite.
It is important to find out natural repellent material against house
dust mite to control them and reduce the allergic reactions. Plants may
be an alternative source for dust mite control because they contain a
range of bioactive chemicals.
The research objectives of this paper were to verify the acaricidal
and repellent effects of cinnamon essential oil and to find out it-s most
effective concentrations. We could find that cinnamon bark essential
oil was very effective material to control the house dust mite.
Furthermore, it could reduce chemical resistance and danger for
human health.
Abstract: Purpose: To develop a method for automatic segmentation of adipose and muscular tissue in thighs from magnetic resonance images. Materials and methods: Thirty obese women were scanned on a Siemens Impact Expert 1T resonance machine. 1500 images were finally used in the tests. The developed segmentation method is a recursive and multilevel process that makes use of several concepts such as shaped histograms, adaptative thresholding and connectivity. The segmentation process was implemented in Matlab and operates without the need of any user interaction. The whole set of images were segmented with the developed method. An expert radiologist segmented the same set of images following a manual procedure with the aid of the SliceOmatic software (Tomovision). These constituted our 'goal standard'. Results: The number of coincidental pixels of the automatic and manual segmentation procedures was measured. The average results were above 90 % of success in most of the images. Conclusions: The proposed approach allows effective automatic segmentation of MRIs from thighs, comparable to expert manual performance.
Abstract: Today technological process makes possible surface
control of producing parts which is needful for product quality
guarantee. Geometrical structure of part surface includes form,
proportion, accuracy to shape, accuracy to size, alignment and
surface topography (roughness, waviness, etc.). All these parameters
are dependence at technology, production machine parameters,
material properties, but also at human, etc. Every parameters
approves at total part accuracy, it is means at accuracy to shape. One
of the most important accuracy to shape element is roundness. This
paper will be deals by comparison of roughness deviations at
coordination measuring machines and at special single purpose
machines. Will describing measuring by discreet method
(discontinuous) and scanning method (continuous) at coordination
measuring machines and confrontation with reference method using
at single purpose machines.
Abstract: The Pads have unique values of thermophysical
properties (THP) having important contribution over heat transfer
into the PCB structure.
Materials with high thermal diffusivity (TD) rapidly adjust their
temperature to that of their surroundings, because the HT is quick in
compare to their volumetric heat capacity (VHC).
In the paper is presenting the diffusivity tests (ASTM E1461 flash
method) for PCBs with different core materials. In the experiments,
the multilayer structure of PCBA was taken into consideration, an
equivalent property referring to each of experimental structure be
practically measured.
Concerning to entire structure, the THP emphasize the major
contribution of substrate in establishing of reflow soldering process
(RSP) heat transfer necessities. This conclusion offer practical
solution for heat transfer time constant calculation as function of
thickness and substrate material diffusivity with an acceptable error
estimation.
Abstract: The OTOP Entrepreneurship that used to create
substantial source of income for local Thai communities are now in a
stage of exigent matters that required assistances from public sectors
due to over Entrepreneurship of duplicative ideas, unable to adjust
costs and prices, lack of innovation, and inadequate of quality
control. Moreover, there is a repetitive problem of middlemen who
constantly corner the OTOP market. Local OTOP producers become
easy preys since they do not know how to add more values, how to
create and maintain their own brand name, and how to create proper
packaging and labeling. The suggested solutions to local OTOP
producers are to adopt modern management techniques, to find
knowhow to add more values to products and to unravel other
marketing problems. The objectives of this research are to study the
prevalent OTOP products management and to discover direction to
manage OTOP products to enhance the effectiveness of OTOP
Entrepreneurship in Nonthaburi Province, Thailand. There were 113
participants in this study. The research tools can be divided into two
parts: First part is done by questionnaire to find responses of the
prevalent OTOP Entrepreneurship management. Second part is the
use of focus group which is conducted to encapsulate ideas and local
wisdom. Data analysis is performed by using frequency, percentage,
mean, and standard deviation as well as the synthesis of several small
group discussions. The findings reveal that 1) Business Resources:
the quality of product is most important and the marketing of product
is least important. 2) Business Management: Leadership is most
important and raw material planning is least important. 3) Business
Readiness: Communication is most important and packaging is least
important. 4) Support from public sector: Certified from the
government is most important and source of raw material is the least
important.
Abstract: Bumpers play an important role in preventing the
impact energy from being transferred to the automobile and
passengers. Saving the impact energy in the bumper to be released in
the environment reduces the damages of the automobile and
passengers.
The goal of this paper is to design a bumper with minimum weight
by employing the Glass Material Thermoplastic (GMT) materials.
This bumper either absorbs the impact energy with its deformation or
transfers it perpendicular to the impact direction.
To reach this aim, a mechanism is designed to convert about 80%
of the kinetic impact energy to the spring potential energy and
release it to the environment in the low impact velocity according to
American standard1. In addition, since the residual kinetic energy
will be damped with the infinitesimal elastic deformation of the
bumper elements, the passengers will not sense any impact. It should
be noted that in this paper, modeling, solving and result-s analysis
are done in CATIA, LS-DYNA and ANSYS V8.0 software
respectively.
Abstract: True stress-strain curve of railhead steel is required to
investigate the behaviour of railhead under wheel loading through elasto-plastic Finite Element (FE) analysis. To reduce the rate of wear, the railhead material is hardened through annealing and
quenching. The Australian standard rail sections are not fully hardened and hence suffer from non-uniform distribution of the
material property; usage of average properties in the FE modelling can potentially induce error in the predicted plastic strains. Coupons
obtained at varying depths of the railhead were, therefore, tested under axial tension and the strains were measured using strain gauges as well as an image analysis technique, known as the Particle Image Velocimetry (PIV). The head hardened steel exhibit existence of three distinct zones of yield strength; the yield strength as the ratio of the average yield strength provided in the standard (σyr=780MPa) and
the corresponding depth as the ratio of the head hardened zone along
the axis of symmetry are as follows: (1.17 σyr, 20%), (1.06 σyr, 20%-80%) and (0.71 σyr, > 80%). The stress-strain curves exhibit limited plastic zone with fracture occurring at strain less than 0.1.
Abstract: The effect of autofrettage process in strain hardened
thick-walled pressure vessels has been investigated theoretically by
finite element modeling. Equivalent von Mises stress is used as yield
criterion to evaluate the optimum autofrettage pressure and the
optimum radius of elastic-plastic junction. It has been observed that
the optimum autofrettage pressure increases along with the working
pressure. For two different working pressures, the effect of the ratio
of outer to inner radius (b/a=k) value on the optimum autofrettage
pressure is also noticed. The Optimum autofrettage pressure solely
depends on K value rather than on the inner or outer radius.
Furthermore, percentage reduction of von Mises stresses is compared
for different working pressures and different k values. Maximum von
Mises stress developed at different autofrettage pressure is equated
for elastic perfectly plastic and elastic-plastic material with different
slope of strain hardening segment. Cylinder material having higher
slope of strain hardening segment provides better benedictions in the
autofrettage process.
Abstract: Using strength Pulse Electrical Field (PEF) in food
industries is a non-thermal process that can deactivate
microorganisms and increase penetration in plant and animals tissues
without serious impact on food taste and quality. In this paper designing and fabricating of a PEF generator has been presented. Pulse generation methods have been surveyed and the best of them
selected. The equipment by controller set can generate square pulse with adjustable parameters such as amplitude 1-5kV, frequency 0.1-10Hz, pulse width 10-100s, and duty cycle 0-100%. Setting the number of pulses, and presenting the output voltage and current
waveforms on the oscilloscope screen are another advantages of this
equipment. Finally, some food samples were tested that yielded the satisfactory results. PEF applying had considerable effects on potato, banana and purple cabbage. It caused increase Brix factor from 0.05
to 0.15 in potato solution. It is also so effective in extraction color material from purple cabbage. In the last experiment effects of PEF
voltages on color extraction of saffron scum were surveyed (about 6% increasing yield).
Abstract: The construction of original functional sample of the portable device for fast analysis of energetic materials has been described in the paper. The portable device consisting of two parts – an original miniaturized microcolumn liquid chromatograph and a unique chemiluminescence detector – has been proposed and realized. In a very short time, this portable device is capable of identifying selectively most of military nitramine- and nitroesterbased explosives as well as inorganic nitrates occurring in trace concentrations in water or in soil. The total time required for the identification of extracts is shorter than 8 minutes.
Abstract: Service life of existing reinforced concrete (RC)
structures in coastal towns of Sabah has been affected very much.
Concrete crack, spalling of concrete cover and reinforcement rusting
of RC buildings are seen even within 5 years of construction in
Sabah. Hence, in this study a new mix design of concrete grout was
developed using locally available materials and investigated under
two curing conditions and workability, compressive strength,
Accelerated Mortar Bar Test (AMBT), water absorption, volume of
permeable voids (VPV), Sorptivity and 90-days salt ponding test
were conducted. The compressive strength of concrete grout at the
age 90 days was found to be 44.49 N/mm2 under water curing. It was
observed that the percentage of mortar bar length change was below
1% for developed concrete grout. The water absorption of the
concrete grout was in between the range of 0.88 % to 3.60 % under
two different curing up to the age 90 days. It was also observed that
the VPV of concrete was in the range of 0 % to 9.75 and 2.44% to
13.05% under water curing and site curing respectively. It was found
that the Sorptivity of the concrete grout under water curing at the age
of 28 days is 0.211mm/√min and at the age 90 day are 0.067
mm/√min. The chloride content decreased greatly, 90% after a depth
of 15 mm. It was noticed that the site cured samples showed higher
chloride contents near surface compared to water cured samples.
This investigation suggested that the developed mix design of
concrete grout using locally available construction materials can be
used for crack repairing of existing RC structures in Sabah.
Abstract: Atherosclerosis is the condition in which an artery
wall thickens as the result of a build-up of fatty materials such as
cholesterol. It is a syndrome affecting arterial blood vessels, a
chronic inflammatory response in the walls of arteries, in large part
due to the accumulation of macrophage white blood cells and
promoted by low density (especially small particle) lipoproteins
(plasma proteins that carry cholesterol and triglycerides) without
adequate removal of fats and cholesterol from the macrophages by
functional high density lipoproteins (HDL). It is commonly referred
to as a hardening or furring of the arteries. It is caused by the
formation of multiple plaques within the arteries.
Abstract: to simulate the phenomenon of electronic transport in semiconductors, we try to adapt a numerical method, often and most frequently it’s that of Monte Carlo. In our work, we applied this method in the case of a ternary alloy semiconductor GaInP in its cubic form; The Calculations are made using a non-parabolic effective-mass energy band model. We consider a band of conduction to three valleys (ΓLX), major of the scattering mechanisms are taken into account in this modeling, as the interactions with the acoustic phonons (elastic collisions) and optics (inelastic collisions). The polar optical phonons cause anisotropic collisions, intra-valleys, very probable in the III-V semiconductors. Other optical phonons, no polar, allow transitions inter-valleys. Initially, we present the full results obtained by the simulation of Monte Carlo in GaInP in stationary regime. We consider thereafter the effects related to the application of an electric field varying according to time, we thus study the transient phenomenon which make their appearance in ternary material
Abstract: The use of synthetic retardants in polymeric insulated
cables is not uncommon in the high voltage engineering to study
electrical treeing phenomenon. However few studies on organic
materials for the same investigation have been carried. .This paper
describes the study on the effects of Oil Palm Empty Fruit Bunch
(OPEFB) microfiller on the tree initiation and propagation in silicone
rubber with different weight percentages (wt %) of filler to insulation
bulk material. The weight percentages used were 0 wt % and 1 wt %
respectively. It was found that the OPEFB retards the propagation of
the electrical treeing development. For tree inception study, the
addition of 1(wt %) OPEFB has increase the tree inception voltage of
silicone rubber. So, OPEFB is a potential retardant to the initiation
and growth of electrical treeing occurring in polymeric materials for
high voltage application. However more studies on the effects of
physical and electrical properties of OPEFB as a tree retardant
material are required.
Abstract: The ability of pomelo peel, a natural biosorbent, to remove Cd(II) ions from aqueous solution by biosorption was investigated. The experiments were carried out by batch method at 25 °C. The influence of solution pH, initial cadmium ion concentrations and contact times were evaluated. Cadmium ion removal increased significantly as the pH of the solution increased from pH 1 to pH 5. At pH 5, the cadmium ion removal reached a maximum value. The equilibrium process was described well by the Langmuir isotherm model, with a maximum biosorption capacity of 21.83 mg/g. The biosorption was relatively quick, (approx. 20 min). Biosorption kinetics followed a pseudo-second-order model. The result showed that pomelo peel was effective as a biosorbent for removing cadmium ions from aqueous solution. It is a low cost material that shows potential to be applied in wastewater technology for remediation of heavy metal contamination.
Abstract: Calcium magnesium acetate (CMA) is environmentally
benign deicing chemicals that can replace sodium chloride that is
widely used on roads and highways at present for snow and ice control
to provide safe driving conditions during winter. The price of CMA
from petroleum-derived acetic acid is quite expensive. The bamboo
vinegar is the by-product from bamboo charcoal production. The
bamboo vinegar was used to prepare calcium acetate as raw materials,
and its deicing and corrosive performances were studied in this paper.
The results show that the freezing temperature of calcium acetate is
lower than that of sodium chloride when they have same molar
concentration, the deicing performance of calcium acetate is better
than that of sodium chloride when they have same moles, while the
deicing performance of sodium chloride is better than that of calcium
acetate. The corrosion of sodium chloride on iron-nail and steel-nail is
larger than that of calcium acetate whether they have same mass
concentration or same molar concentration, and the corrosion of
sodium chloride and calcium acetate on iron-nail is larger than that on
steel-nail, and calcium acetate almost hasn't corrosion on steel-nail.
Abstract: Production of hard-to-cut materials with uncoated carbide cutting tools in turning, not only cause tool life reduction but also, impairs the product surface roughness. In this paper, influence of hot machining method were studied and presented in two cases. Case1-Workpiece surface roughness quality with constant cutting parameter and 300 ºC initial workpiece surface temperature. Case 2- Tool temperature variation when cutting with two speeds 78.5 (m/min) and 51 (m/min). The workpiece material and tool used in this study were AISI 1060 steel (45HRC) and uncoated carbide TNNM 120408-SP10(SANDVIK Coromant) respectively. A gas flam heating source was used to preheating of the workpiece surface up to 300 ºC, causing reduction of yield stress about 15%. Results obtained experimentally, show that the method used can considerably improved surface quality of the workpiece.
Abstract: Acute toxicity of nano SiO2, ZnO, MCM-41 (Meso
pore silica), Cu, Multi Wall Carbon Nano Tube (MWCNT), Single
Wall Carbon Nano Tube (SWCNT) , Fe (Coated) to bacteria Vibrio
fischeri using a homemade luminometer , was evaluated. The values
of the nominal effective concentrations (EC), causing 20% and 50%
inhibition of biouminescence, using two mathematical models at two
times of 5 and 30 minutes were calculated. Luminometer was
designed with Photomultiplier (PMT) detector. Luminol
chemiluminescence reaction was carried out for the calibration graph.
In the linear calibration range, the correlation coefficients and
coefficient of Variation (CV) were 0.988 and 3.21% respectively
which demonstrate the accuracy and reproducibility of the instrument
that are suitable. The important part of this research depends on how
to optimize the best condition for maximum bioluminescence. The
culture of Vibrio fischeri with optimal conditions in liquid media,
were stirring at 120 rpm at a temperature of 150C to 180C and were
incubated for 24 to 72 hours while solid medium was held at 180C
and for 48 hours. Suspension of nanoparticles ZnO, after 30 min
contact time to bacteria Vibrio fischeri, showed the highest toxicity
while SiO2 nanoparticles showed the lowest toxicity. After 5 min
exposure time, the toxicity of ZnO was the strongest and MCM-41
was the weakest toxicant component.
Abstract: Use of microemulsion in enhanced oil recovery has become more attractive in recent years because of its high level of extraction efficiency. Experimental investigations have been made on characterization of microemulsions of oil-brinesurfactant/ cosurfactant system for its use in enhanced oil recovery (EOR). Sodium dodecyl sulfate, propan-1-ol and heptane were selected as surfactant, cosurfactant and oil respectively for preparation of microemulsion. The effects of salinity on the relative phase volumes and solubilization parameters have also been studied. As salinity changes from low to high value, phase transition takes place from Winsor I to Winsor II via Winsor III. Suitable microemulsion composition has been selected based on its stability and ability to reduce interfacial tension. A series of flooding experiments have been performed using the selected microemulsion. The flooding experiments were performed in a core flooding apparatus using uniform sand pack. The core holder was tightly packed with uniform sands (60-100 mesh) and saturated with brines of different salinities. It was flooded with the brine at 25 psig and the absolute permeability was calculated from the flow rate of the through sand pack. The sand pack was then flooded with the crude oil at 800 psig to irreducible water saturation. The initial water saturation was determined on the basis of mass balance. Waterflooding was conducted by placing the coreholder horizontally at a constant injection pressure at 200 pisg. After water flooding, when water-cut reached above 95%, around 0.5 pore volume (PV) of the above microemulsion slug was injected followed by chasing water. The experiments were repeated using different composition of microemulsion slug. The additional recoveries were calculated by material balance. Encouraging results with additional recovery more than 20% of original oil in place above the conventional water flooding have been observed.
Abstract: Currently, most of distance learning courses can only
deliver standard material to students. Students receive course content
passively which leads to the neglect of the goal of education – “to suit
the teaching to the ability of students". Providing appropriate course
content according to students- ability is the main goal of this paper.
Except offering a series of conventional learning services, abundant
information available, and instant message delivery, a complete online
learning environment should be able to distinguish between students-
ability and provide learning courses that best suit their ability.
However, if a distance learning site contains well-designed course
content and design but fails to provide adaptive courses, students will
gradually loss their interests and confidence in learning and result in
ineffective learning or discontinued learning. In this paper, an
intelligent tutoring system is proposed and it consists of several
modules working cooperatively in order to build an adaptive learning
environment for distance education. The operation of the system is
based on the result of Self-Organizing Map (SOM) to divide students
into different groups according to their learning ability and learning
interests and then provide them with suitable course content.
Accordingly, the problem of information overload and internet traffic
problem can be solved because the amount of traffic accessing the
same content is reduced.