Abstract: In order to enhance the aircraft survivability, the
infrared signatures emitted by hot engine parts should be determined
exactly. For its reduction it is necessary for the rear fuselage
temperature to be decreased. In this study, numerical modeling of flow
fields and heat transfer characteristics of an aircraft nozzle is
performed and its temperature distribution along each component wall
is predicted. The radiation shield is expected to reduce the skin
temperature of rear fuselage. The effect of material characteristic of
radiation shield on the heat transfer is also investigated. Through this
numerical analysis, design parameters related to the susceptibility of
aircraft are examined.
Abstract: The experimental results on combustion of rice husk
in a conical fluidized bed combustor (referred to as the conical FBC)
using silica sand as the bed material are presented in this paper. The
effects of excess combustion air and combustor loading as well as the
sand bed height on the combustion pattern in FBC were investigated.
Temperatures and gas concentrations (CO and NO) along over the
combustor height as well as in the flue gas downstream from the ash
collecting cyclone were measured. The results showed that the axial
temperature profiles in FBC were explicitly affected by the
combustor loading whereas the excess air and bed height were found
to have minor influences on the temperature pattern. Meanwhile, the
combustor loading and the excess air significantly affected the axial
CO and NO concentration profiles; however, these profiles were
almost independent of the bed height. The combustion and thermal
efficiencies for this FBC were quantified for different operating
conditions.
Abstract: Friction Stir Welding is a solid state welding technique which can be used to produce sound welds between similar and dissimilar materials. Dissimilar welds which include welds between the different series of aluminium alloys, aluminium to magnesium, steel and titanium has been successfully produced by many researchers. This review covers the work conducted in the above mentioned materials and further concludes by showing the need to fully understand the FSW process in order to expand the latter industrially.
Abstract: When considering the development of constitutive
equations describing the behavior of materials under cyclic plastic
strains, different kinds of formulations can be adopted. The primary
intention of this study is to develop computer programming of
plasticity models to accurately predict the life of engineering
components. For this purpose, the energy or cyclic strain is computed
in multi-surface plasticity models in non-proportional loading and to
present their procedures and codes results.
Abstract: In this paper, free vibration analysis of carbon nanotube (CNT) reinforced laminated composite panels is presented. Three types of panels such as flat, concave and convex are considered for study. Numerical simulation is carried out using commercially available finite element analysis software ANSYS. Numerical homogenization is employed to calculate the effective elastic properties of randomly distributed carbon nanotube reinforced composites. To verify the accuracy of the finite element method, comparisons are made with existing results available in the literature for conventional laminated composite panels and good agreements are obtained. The results of the CNT reinforced composite materials are compared with conventional composite materials under different boundary conditions.
Abstract: This work deals with problems of tool axis inclination angles in ball-end milling. Tool axis inclination angle contributes to improvement of functional surface properties (surface integrity - surface roughness, residual stress, micro hardness, etc.), decreasing cutting forces and improving production. By milling with ball-end milling tool, using standard way of cutting, when work piece and cutting tool contain right angle, we have zero cutting speed on edge. At this point cutting tool only pushes material into the work piece. Here we can observe the following undesirable effects - chip contraction, increasing of cutting temperature, increasing vibrations or creation of built-up edge. These effects have negative results – low quality of surface and decreasing of tool life (in the worse case even it is pinching out). These effects can be eliminated with the tilt of cutting tool or tilt of work piece.
Abstract: In sport, human resources management gives special
attention to method of applying volunteers, their maintenance, and
participation of volunteers with each other and management
approaches for better operation of events celebrants. The recognition
of volunteers- characteristics and motives is important to notice,
because it makes the basis of their participation and commitment at
sport environment. The motivation and commitment of 281
volunteers were assessed using the organizational commitment scale,
motivation scale and personal characteristics questionnaire.The
descriptive results showed that; 64% of volunteers were women with
age average 21/24 years old. They were physical education student,
single (71/9%), without occupation (53%) and with average of 5
years sport experience. Their most important motivation was career
factor and the most important commitment factor was normative
factor. The results of examining the hypothesized showed that; age,
sport experience and education are effective in the amount of
volunteers- commitment. And the motive factors such as career,
material, purposive and protective factors also have the power to
predict the amount of sports volunteers- commitment value.
Therefore it is recommended to provide possible opportunities for
volunteers and carrying out appropriate instructional courses by
events executive managers.
Abstract: Within the last years, several technologies have been developed to help building e-learning portals. Most of them follow approaches that deliver a vast amount of functionalities, suitable for class-like learning. The SuGI project, as part of the D-Grid (funded by the BMBF), targets on delivering a highly scalable and sustainable learning solution to provide materials (e.g. learning modules, training systems, webcasts, tutorials, etc.) containing knowledge about Grid computing to the D-Grid community. In this article, the process of the development of an e-learning portal focused on the requirements of this special user group is described. Furthermore, it deals with the conceptual and technical design of an e-learning portal, addressing the special needs of heterogeneous target groups. The main focus lies on the quality management of the software development process, Web templates for uploading new contents, the rich search and filter functionalities which will be described from a conceptual as well as a technical point of view. Specifically, it points out best practices as well as concepts to provide a sustainable solution to a relatively unknown and highly heterogeneous community.
Abstract: A major challenge in biomaterials research is the
regulation of protein adsorption which is a key factor for controlling
the subsequent cell adhesion at implant surfaces. The aim of the
present study was to control the adsorption of fibronectin (FN) and
the attachment of MG-63 osteoblasts with an electronic
nanostructure. Shallow doping line lattices with a period of 260 nm
were produced for this purpose by implantation of phosphorous in
silicon wafers. Protein coverage was determined after incubating the
substrate with FN by means of an immunostaining procedure and the
measurement of the fluorescence intensity with a TECAN analyzer.
We observed an increased amount of adsorbed FN on the
nanostructure compared to control substrates. MG-63 osteoblasts
were cultivated for 24h on FN-incubated substrates and their
morphology was assessed by SEM. Preferred orientation and
elongation of the cells in direction of the doping lattice lines was
observed on FN-coated nanostructures.
Abstract: One of the most important problems in production planning of flexible manufacturing system (FMS) is machine tool selection and operation allocation problem that directly influences the production costs and times .In this paper minimizing machining cost, set-up cost and material handling cost as a multi-objective problem in flexible manufacturing systems environment are considered. We present a 0-1 integer linear programming model for the multiobjective machine tool selection and operation allocation problem and due to the large scale nature of the problem, solving the problem to obtain optimal solution in a reasonable time is infeasible, Paretoant colony optimization (P-ACO) approach for solving the multiobjective problem in reasonable time is developed. Experimental results indicate effectiveness of the proposed algorithm for solving the problem.
Abstract: In this project cadmium ions were adsorbed from
aqueous solutions onto either date pits; a cheap agricultural and nontoxic
material, or chemically activated carbon prepared from date pits
using phosphoric acid. A series of experiments were conducted in a
batch adsorption technique to assess the feasibility of using the
prepared adsorbents. The effects of the process variables such as
initial cadmium ions concentration, contact time, solution pH and
adsorbent dose on the adsorption capacity of both adsorbents were
studied. The experimental data were tested using different isotherm
models such as Langmuir, Freundlich, Tempkin and Dubinin-
Radushkevich. The results showed that although the equilibrium data
could be described by all models used, Langmuir model gave slightly
better results when using activated carbon while Freundlich model,
gave better results with date pits.
Abstract: Selective oxidation of H2S to elemental sulfur in a
fixed bed reactor over newly synthesized alumina nanocatalysts was
physio-chemically investigated and results compared with a
commercial Claus catalyst. Amongst these new materials, Al2O3-
supported sodium oxide prepared with wet chemical technique and
Al2O3 nanocatalyst prepared with spray pyrolysis method were the
most active catalysts for selective oxidation of H2S to elemental
sulfur. Other prepared nanocatalysts were quickly deactivated,
mainly due to the interaction with H2S and conversion into sulfides.
Abstract: Polyphenolics and sugar are the components of many
fruit juices. In this work, the performance of ultra-filtration (UF) for
separating phenolic compounds from apple juice was studied by
performing batch experiments in a membrane module with an area of
0.1 m2 and fitted with a regenerated cellulose membrane of 1 kDa
MWCO. The effects of various operating conditions: transmembrane
pressure (3, 4, 5 bar), temperature (30, 35, 40 ºC), pH (2, 3, 4, 5),
feed concentration (3, 5, 7, 10, 15 ºBrix for apple juice) and feed flow
rate (1, 1.5, 1.8 L/min) on the performance were determined.
The optimum operating conditions were: transmembrane pressure
4 bar, temperature 30 ºC, feed flow rate 1 – 1.8 L/min, pH 3 and 10
Brix (apple juice). After performing ultrafiltration under these
conditions, the concentration of polyphenolics in retentate was
increased by a factor of up to 2.7 with up to 70% recovered in the
permeate and with approx. 20% of the sugar in that stream..
Application of diafiltration (addition of water to the concentrate) can
regain the flux by a factor of 1.5, which has been decreased due to
fouling. The material balance performed on the process has shown
the amount of deposits on the membrane and the extent of fouling in
the system. In conclusion, ultrafiltration has been demonstrated as a
potential technology to separate the polyphenolics and sugars from
their mixtures and can be applied to remove sugars from fruit juice.
Abstract: Korea Train eXpress (KTX) is now being operated,
which allows Korea being one of the countries that operates the
high-speed rail system. The high-speed rail has its advantage of short
time transportation of population and materials, which lead to many
researches performed in this matter. In the case of high speed classical
trackbed system, the maintenance and usability of gravel ballast
system is costly. Recently, the concrete trackbed structure has been
introduced as a replacement of classical trackbed system. In this case,
the sleeper plays a critical role. Current study investigated to develop
the track sleepers readily applicable to the top of the asphalt trackbed,
as part of the trcakbed study utilizing the asphalt material. Among
many possible shapes and design of sleepers, current study proposed
two types of wide-sleepers according to the shear-key installation
method. The structural behavior analysis and safety evaluation on each
case was conducted using Korean design standard.
Abstract: Water 2H NMR signal on the surface of nano-silica material, MCM-41, consists of two overlapping resonances. The 2H water spectrum shows a superposition of a Lorentzian line shape and the familiar NMR powder pattern line shape, indicating the existence of two spin components. Chemical exchange occurs between these two groups. Decomposition of the two signals is a crucial starting point for study the exchange process. In this article we have determined these spin component populations along with other important parameters for the 2H water NMR signal over a temperature range between 223 K and 343 K.
Abstract: Metal matrix composites (MMC) are generating
extensive interest in diverse fields like defense, aerospace, electronics
and automotive industries. In this present investigation, material
removal rate (MRR) modeling has been carried out using an
axisymmetric model of Al-SiC composite during electrical discharge
machining (EDM). A FEA model of single spark EDM was
developed to calculate the temperature distribution.Further, single
spark model was extended to simulate the second discharge. For
multi-discharge machining material removal was calculated by
calculating the number of pulses. Validation of model has been done
by comparing the experimental results obtained under the same
process parameters with the analytical results. A good agreement was
found between the experimental results and the theoretical value.
Abstract: Carbon steel is used in boilers, pressure vessels, heat
exchangers, piping, structural elements and other moderatetemperature
service systems in which good strength and ductility are
desired. ASME Boiler and Pressure Vessel Code, Section II Part A
(2004) provides specifications of ferrous materials for construction of
pressure equipment, covering wide range of mechanical properties
including high strength materials for power plants application.
However, increased level of springback is one of the major problems
in fabricating components of high strength steel using bending.
Presented work discuss the springback simulations for five different
steels (i.e. SA-36, SA-299, SA-515 grade 70, SA-612 and SA-724
grade B) using finite element analysis of air V-bending. Analytical
springback simulations of hypothetical layered materials are
presented. Result shows that; (i) combination of the material property
parameters controls the springback, (ii) layer of the high ductility
steel on the high strength steel greatly suppresses the springback.
Abstract: The article contains results of the flour and bread
quality assessment from the grains of spring spelt, also called as an
ancient wheat. Spelt was cultivated on heavy and medium soils
observing principles of organic farming. Based on flour and bread
laboratory studies, as well as laboratory baking, the technological
usefulness of studied flour has been determined. These results were
referred to the standard derived from common wheat cultivated in the
same conditions. Grain of spring spelt is a good raw material for
manufacturing bread flour, from which to get high-quality bakery
products, but this is strictly dependent on the variety of ancient
wheat.
Abstract: A numerical analysis of a reinforced concrete (RC) wall under missile impact loading is presented in this study. The model created by Technical Research Center of Finland was used. The commercial finite element code, LS-DYNA was used to analyze. The structural components of the reinforced concrete wall, missile and their contacts are fully modeled. The material nonlinearity with strain rate effects considering damage and failure is included in the analysis. The results of analysis were verified with other research results. The case-studies with different reinforcement ratios were conducted to investigate the influence of reinforcement on the punching behavior of walls under missile impact.
Abstract: Polymer-like organic thin films were deposited on both
aluminum alloy type 6061 and glass substrates at room temperature by
Plasma Enhanced Chemical Vapor Deposition (PECVD) methodusing
benzene and hexamethyldisiloxane (HMDSO) as precursor materials.
The surface and physical properties of plasma-polymerized organic
thin films were investigated at different r.f. powers. The effects of
benzene/argon ratio on the properties of plasma polymerized benzene
films were also investigated. It is found that using benzene alone
results in a non-coherent and non-adherent powdery deposited
material. The chemical structure and surface properties of the asgrown
plasma polymerized thin films were analyzed on glass
substrates with FTIR and contact angle measurements. FTIR spectra
of benzene deposited film indicated that the benzene rings are
preserved when increasing benzene ratio and/or decreasing r.f.
powers. FTIR spectra of HMDSO deposited films indicated an
increase of the hydrogen concentration and a decrease of the oxygen
concentration with the increase of r.f. power. The contact angle (θ) of
the films prepared from benzene was found to increase by about 43%
as benzene ratio increases from 10% to 20%. θ was then found to
decrease to the original value (51°) when the benzene ratio increases
to 100%. The contact angle, θ, for both benzene and HMDSO
deposited films were found to increase with r.f. power. This signifies
that the plasma polymerized organic films have substantially low
surface energy as the r.f power increases. The corrosion resistance of
aluminum alloy substrate both bare and covered with plasma
polymerized thin films was carried out by potentiodynamic
polarization measurements in standard 3.5 wt. % NaCl solution at
room temperature. The results indicate that the benzene and HMDSO
deposited films are suitable for protection of the aluminum substrate
against corrosion. The changes in the processing parameters seem to
have a strong influence on the film protective ability. Surface
roughness of films deposited on aluminum alloy substrate was
investigated using scanning electron microscopy (SEM). The SEM
images indicate that the surface roughness of benzene deposited films
increase with decreasing the benzene ratio. SEM images of benzene
and HMDSO deposited films indicate that the surface roughness
decreases with increasing r.f. power. Studying the above parameters
indicate that the films produced are suitable for specific practical
applications.