Abstract: This article presents the main results of a numerical
investigation on the uncertainty of dynamic response of structures
with statistically correlated random damping Gamma distributed. A
computational method based on a Linear Statistical Model (LSM) is
implemented to predict second order statistics for the response of a
typical industrial building structure. The significance of random
damping with correlated parameters and its implications on the
sensitivity of structural peak response in the neighborhood of a
resonant frequency are discussed in light of considerable ranges of
damping uncertainties and correlation coefficients. The results are
compared to those generated using Monte Carlo simulation
techniques. The numerical results obtained show the importance of
damping uncertainty and statistical correlation of damping
coefficients when obtaining accurate probabilistic estimates of
dynamic response of structures. Furthermore, the effectiveness of the
LSM model to efficiently predict uncertainty propagation for
structural dynamic problems with correlated damping parameters is
demonstrated.
Abstract: The study conducted a simulation of the effect of sea
water to the bonding capacity of GFRP sheet on the concrete beams
using a simulation tank. Fiber reinforced polymer (FRP) has been
developed and applied in many fields civil engineering structures on
the new structures and also for strengthening of the deteriorated
structures. The FRP has advantages such as its corrosion resistance as
well as high tensile strength to weight ratio. Compared to the other
FRP materials, Glass composed FRP (GFRP) is relatively cheaper.
GFRP sheet is applied externally by bonding it on the concrete surface.
The studies regarding the application of GFRP sheet have been
conducted such as strengthening system, bonding behavior of GFRP
sheet including the application as reinforcement in new structures. For
application to the structures with direct contact to sea environment, a
study regarding the effect of sea water to the bonding capacity of
GFRP sheet is important to be clarified. To achieve the objective of the
study, a series of concrete beams strengthened with GFRP sheet on
extreme tension surface were prepared. The beams then were stored on
the sea water tank for six months. Results indicated the bonding
capacity decreased after six month exposed to the sea water.
Abstract: In the last decade the emergence of new social needs
as an effect of the economic crisis has stimulated the flourishing of
business endeavours characterised by explicit social goals. Social
start-ups, social enterprises or Corporate Social Responsibility
operations carried out by traditional companies are quintessential
examples in this regard. This paper analyses these kinds of initiatives
in order to discover the main characteristics of social business models
and to provide insights to social entrepreneurs for developing or
improving their strategies. The research is conducted through the
integration of literature review and case study analysis and, thanks to
the recognition of the importance of both profits and social impacts
as the key success factors for a social business model, proposes a
framework for identifying indicators suitable for measuring the social
impacts generated.
Abstract: The Green Urban Lab took the form of public
installations that were placed at various locations in four cities in
Cyprus. These installations - through which a series of events,
activities, workshops and research took place - were the main tools in
regenerating a series of urban public spaces in Cyprus. The purpose
of this project was to identify issues and opportunities related to
public space and to offer guidelines on how design and participatory
democracy improvements could strengthen civil society, while
raising the quality of the urban public scene. Giant inflatable
structures were injected in important urban fragments in order to
accommodate series of events. The design and playful installation
generated a wide community engagement. The fluid presence of the
installations acted as a catalyst for social interaction. They were
accessed and viewed effortlessly and surprisingly, creating
opportunities to rediscover public spaces.
Abstract: Carbon Fiber Reinforced Plastics (CFRPs) are widely
used for advanced applications, in particular in aerospace, automotive
and wind energy industries. Once cured to near net shape, CFRP
parts need several finishing operations such as trimming, milling or
drilling in order to accommodate fastening hardware and meeting the
final dimensions. The present research aims to study the effect of the
cutting temperature in trimming on the mechanical strength of high
performance CFRP laminates used for aeronautics applications. The
cutting temperature is of great importance when dealing with
trimming of CFRP. Temperatures higher than the glass-transition
temperature (Tg) of the resin matrix are highly undesirable: they
cause degradation of the matrix in the trimmed edges area, which can
severely affect the mechanical performance of the entire component.
In this study, a 9.50mm diameter CVD diamond coated carbide tool
with six flutes was used to trim 24-plies CFRP laminates. A
300m/min cutting speed and 1140mm/min feed rate were used in the
experiments. The tool was heated prior to trimming using a
blowtorch, for temperatures ranging from 20°C to 300°C. The
temperature at the cutting edge was measured using embedded KType
thermocouples. Samples trimmed for different cutting
temperatures, below and above Tg, were mechanically tested using
three-points bending short-beam loading configurations. New cutting
tools as well as worn cutting tools were utilized for the experiments.
The experiments with the new tools could not prove any correlation
between the length of cut, the cutting temperature and the mechanical
performance. Thus mechanical strength was constant, regardless of
the cutting temperature. However, for worn tools, producing a cutting
temperature rising up to 450°C, thermal damage of the resin was
observed. The mechanical tests showed a reduced mean resistance in
short beam configuration, while the resistance in three point bending
decreases with increase of the cutting temperature.
Abstract: Myocardial infarction is one of the leading causes of
death in the world. Some of these deaths occur even before the
patient reaches the hospital. Myocardial infarction occurs as a result
of impaired blood supply. Because the most of these deaths are due to
coronary artery disease, hence the awareness of the warning signs of
a heart attack is essential. Some heart attacks are sudden and intense,
but most of them start slowly, with mild pain or discomfort, then
early detection and successful treatment of these symptoms is vital to
save them. Therefore, importance and usefulness of a system
designing to assist physicians in early diagnosis of the acute heart
attacks is obvious. The main purpose of this study would be to enable patients to
become better informed about their condition and to encourage them
to seek professional care at an earlier stage in the appropriate
situations. For this purpose, the data were collected on 711 heart
patients in Iran hospitals. 28 attributes of clinical factors can be
reported by patients; were studied. Three logistic regression models
were made on the basis of the 28 features to predict the risk of heart
attacks. The best logistic regression model in terms of performance
had a C-index of 0.955 and with an accuracy of 94.9%. The variables,
severe chest pain, back pain, cold sweats, shortness of breath, nausea
and vomiting, were selected as the main features.
Abstract: Public participation in recycling domestic waste is still
very low in Malaysia. Only 10.5% of solid waste was recycled up to
now which is far below than of in developed countries. Therefore,
understanding public motivations towards recycling domestic waste
are important to improve current recycling rate. Thus, this study
attempts to identify what are the possible motivations and hindrances
for the public to recycle. Open-ended questions format were
administered to 484 people in Kota Kinabalu, Sabah, Malaysia. Two
specific questions we asked to explore their general determinants and
barriers in practicing recycling: “What motivates you to recycle?”
and “What are the barriers you encountered in doing recycling
activities?” Thematic was conducted on the open-ended questions in
which themes were created with the raw comments. It was found that
the underlying recycling motivations are (i) awareness’ towards the
environment; (ii) benefits to the society and individual; and (iii)
social influence. Non participations are influence by (i) attitudes; (ii)
commitment; (iii) facilities; (iv) knowledge; (v) inconvenience; and
(vi) enforcement.
Abstract: On account of the concern of the fossil fuel is
depleting and its negative effects on the environment, interest in
alternative energy sources is increasing day by day. However,
considering the importance of transportation in human life, instead of
oil and its derivatives fueled vehicles with internal combustion
engines, electric vehicles which are sensitive to the environment and
working with electrical energy has begun to develop. In this study,
simulation was carried out for providing energy management and
recovering regenerative braking in fuel cell-battery hybrid electric
vehicle. The main power supply of the vehicle is fuel cell on the other
hand not only instantaneous power is supplied by the battery but also
the energy generated due to regenerative breaking is stored in the
battery. Obtained results of the simulation is analyzed and discussed.
Abstract: Dead wood and habitat tree such as fallen logs, snags,
stumps and cracks and loos bark etc. are regarded as an important
ecological component of forests on which many forest dwelling
species depend on presence of them within forest ecosystems.
Meanwhile its relation to management history in Caspian forest has
gone unreported. The aim of research was to compare the amounts of
dead wood and habitat trees in the forests with historically different
intensities of management, including: forests with the long term
implication of management (PS), the short term implication of
management (NS) which were compared with semi virgin forest
(GS). The number of 405 individual dead and habitat trees were
recorded and measured at 109 sampling locations. ANOVA revealed
volume of dead tree in the form and decay classes significantly differ
within sites and dead volume in the semi virgin forest significantly
higher than managed sites. Comparing the amount of dead and
habitat tree in three sites showed that, dead tree volume related with
management history and significantly differ in three study sites.
Meanwhile, frequency of habitat trees was significantly different
within sites. The highest amount of habitat trees including cavities,
cracks and loose bark and fork split trees was recorded in virgin site
and lowest recorded in the sites with the long term implication of
management. It can be concluded that forest management cause
reduction of the amount of dead and habitat tree specially in a large
size, thus managing this forest according to ecological sustainable
principles require a commitment to maintaining stand structure that
allow, continued generation of dead trees in a full range of size.
Abstract: In this paper, a asymptotically periodic predator-prey
model with Modified Leslie-Gower and Holling-Type II schemes
is investigated. Some sufficient conditions for the uniformly strong
persistence of the system are established. Our result is an important
complementarity to the earlier results.
Abstract: The reheating furnace is used to reheat the steel slabs
before the hot-rolling process. The supported system includes the
stationary/moving beams, and the skid buttons which block some
thermal radiation transmitted to the bottom of the slabs. Therefore, it is
important to analyze the steel slab temperature distribution during the
heating period. A three-dimensional mathematical transient heat
transfer model for the prediction of temperature distribution within the
slab has been developed. The effects of different skid button height
(H=60mm, 90mm, and 120mm) and different gap distance between
two slabs (S=50mm, 75mm, and 100mm) on the slab skid mark
formation and temperature profiles are investigated. Comparison with
the in-situ experimental data from Steel Company in Taiwan shows
that the present heat transfer model works well for the prediction of
thermal behavior of the slab in the reheating furnace. It is found that
the skid mark severity decreases with an increase in the skid button
height. The effect of gap distance is important only for the slab edge
planes, while it is insignificant for the slab central planes.
Abstract: Automated Teller Machines (ATMs) can be
considered among one of the most important service facilities in the
banking industry. The investment in ATMs and the impact on the
banking industry is growing steadily in every part of the world. The
banks take into consideration many factors like safety, convenience,
visibility, and cost in order to determine the optimum locations of
ATMs. Today, ATMs are not only available in bank branches but
also at retail locations. Another important factor is the cash
management in ATMs. A cash demand model for every ATM is
needed in order to have an efficient cash management system. This
forecasting model is based on historical cash demand data which is
highly related to the ATMs location. So, the location and the cash
management problem should be considered together. This paper
provides a general review on studies, efforts and development in
ATMs location and cash management problem.
Abstract: With the increasing population and intensive land use,
huge traffic demand is generating worldwide both in developing and
developed countries. As a developing country, Bangladesh is also
facing the same problem in recent years by producing huge numbers
of daily trips. As a matter of fact, extensive traffic demand is
increasing day by day. Also, transport system in Dhaka is
heterogeneous, reflecting the heterogeneity in the socio-economic
and land use patterns. Trips produced here are for different purposes
such as work, business, educational etc. Due to the significant
concentration of educational institutions a large share of the trips are
generated by educational purpose. And one of the major percentages
of educational trips is produced by university going students and
most of them are travelled by car, bus, train, taxi, rickshaw etc. The
aim of the study was to find out the university students’ perception on
public transit ridership. A survey was conducted among 330 students
from eight different universities. It was found out that 26% of the
trips produced by university going students are travelled by public
bus service and only 5% are by train. Percentage of car share is 16%
and 12% of the trips are travelled by private taxi. It has been
observed from the study, students those who prefer bus instead of
other options, 42 percent of their family resides outside Dhaka. And
those who prefer walking, of them, over 40 percent students’ family
reside outside of Dhaka and of them over 85 percent students have a
tendency to live in a mess. On the contrary, students travelling by car
represents, most of their family reside in Dhaka. The study also
revealed that the most important reason that restricts students not to
use public transit is poor service. Negative attitudes such as
discomfort, uneasiness in using public transit also reduces the usage
of public transit. The poor waiting area is another major cause of not
using public transit. Insufficient security also plays a significant role
in not using public transit. On the contrary, the fare is not a problem
for students those who use public transit as a mode of transportation.
Students also think stations are not far away from their home or
institution and they do not need to wait long for the buses or trains. It
was also found accessibility to public transit is moderate.
Abstract: The market competition is moving from the single
firm to the whole supply chain because of increasing competition and
growing need for operational efficiencies and customer orientation.
Supply chain management allows companies to look beyond their
organizational boundaries to develop and leverage resources and
capabilities of their supply chain partners. This creates competitive
advantages in the marketplace and because of this SCM has acquired
strategic importance. Lean Approach is a management strategy that focuses on reducing
every type of waste present in an organization. This approach is
becoming more and more popular among supply chain managers. The supply chain application of lean approach is not frequent. In
particular, it is not well studied which are the impacts of lean
approach principles in a supply chain context. In literature there are
only few studies aimed at understanding the qualitative impact of the
lean approach in supply chains. Therefore, the goal of this research
work is to study the impacts of lean principles implementation along
a supply chain. To achieve this, a simulation model of a threeechelon
multi-product supply chain has been built. Kanban system (and several priority policies) and setup time
reduction degrees are implemented in the lean-configured supply
chain to apply pull and lot-sizing decrease principles respectively. To
evaluate the benefits of lean approach, lean supply chain is compared
with an EOQ-configured supply chain. The simulation results show
that Kanban system and setup-time reduction improve inventory
stock level. They also show that logistics efforts are affected to lean
implementation degree. The paper concludes describing
performances of lean supply chain in different contexts.
Abstract: Objectives: To determine the nutritional status and
risk factors associated with women practicing geophagia in QwaQwa,
South Africa. Materials and Methods: An observational epidemiological study
design was adopted which included an exposed (geophagia) and nonexposed
(control) group. A food frequency questionnaire, anthropometric measurements and blood sampling were applied to
determine nutritional status of participants. Logistic regression
analysis was performed in order to identify factors that were likely to
be associated with the practice of geophagia. Results: The mean total energy intake for the geophagia group (G)
and control group (C) were 10324.31 ± 2755.00 kJ and 10763.94 ±
2556.30 kJ respectively. Both groups fell within the overweight
category according to the mean Body Mass Index (BMI) of each
group (G= 25.59 kg/m2; C= 25.14 kg/m2). The mean serum iron
levels of the geophagia group (6.929 μmol/l) were significantly lower
than that of the control group (13.75 μmol/l) (p = 0.000). Serum
transferrin (G=3.23g/l; C=2.7054g/l) and serum transferrin saturation
(G=8.05%; C=18.74%) levels also differed significantly between
groups (p=0.00). Factors that were associated with the practice of
geophagia included haemoglobin (Odds ratio (OR):14.50), serumiron
(OR: 9.80), serum-ferritin (OR: 3.75), serum-transferrin (OR:
6.92) and transferrin saturation (OR: 14.50). A significant negative
association (p=0.014) was found between women who were wageearners
and those who were not wage-earners and the practice of
geophagia (OR: 0.143; CI: 0.027; 0.755). These findings seem to
indicate that a permanent income may decrease the likelihood of
practising geophagia. Key Findings: Geophagia was confirmed to be a risk factor for
iron deficiency in this community. The significantly strong
association between geophagia and iron deficiency emphasizes the
importance of identifying the practice of geophagia in women,
especially during their child bearing years.
Abstract: Processing of high-silicon bauxite on the base of the
traditional clinkering method is related to high power consumption
and capital investments, which makes production of alumina from
those ores non-competitive in terms of basic economic showings. For
these reasons, development of technological solutions enabling to
process bauxites with various chemical and mineralogical structures
efficiently with low level of thermal power consumption is important.
Flow sheet of the studies on washability of ores from the Timanskoe
and the Severo-Onezhskoe deposits is on the base of the flotation
method.
Abstract: Zinc borate is an important inorganic hydrate borate
material, which can be used as a flame retardant agent and corrosion
resistance material. This compound can loss its structural water
content at higher than 290°C. Due to thermal stability; Zinc Borate
can be used as flame retardant at high temperature process of plastic
and gum. In this study, the ultrasonic reaction of zinc borates were
studied using hydrozincite (Zn5(CO3)2·(OH)6) and boric acid
(H3BO3) raw materials. Before the synthesis raw materials were
characterized by X-Ray Diffraction (XRD) and Fourier Transform
Infrared Spectroscopy (FT-IR). Ultrasonic method is a new
application on the zinc borate synthesis. The synthesis parameters
were set to 90°C reaction temperature and 55 minutes of reaction
time, with 1:1, 1:2, 1:3, 1:4 and 1:5 molar ratio of starting materials
(Zn5(CO3)2·(OH)6 : H3BO3). After the zinc borate synthesis, the
products were analyzed by XRD and FT-IR. As a result, optimum
molar ratio of 1:5 is determined for the synthesis of zinc borates with
ultrasonic method.
Abstract: The research explores the relationship between
management responsibility and corporate governance of listed
companies in Kazakhstan. This research employs firm level data of
selected listed non-financial firms and firm level data “operational”
financial sector, consisted from banking sector, insurance companies
and accumulated pension funds using multivariate regression analysis
under fixed effect model approach. Ownership structure includes
institutional ownership, managerial ownership and private investor’s
ownership. Management responsibility of the firm is expressed by the
decision of the firm on amount of leverage. Results of the cross
sectional panel study for non-financial firms showed that only
institutional shareholding is significantly negatively correlated with
debt to equity ratio. Findings from “operational” financial sector
show that leverage is significantly affected only by the CEO/Chair
duality and the size of financial institutions, and insignificantly
affected by ownership structure. Also, the findings show, that there is
a significant negative relationship between profitability and the debt
to equity ratio for non-financial firms, which is consistent with
pecking order theory. Generally, the found results suggest that
corporate governance and a management responsibility play
important role in corporate performance of listed firms in
Kazakhstan.
Abstract: Radical technological innovations enable companies
to reach strong market positions and are thus desirable. On the other
hand, the innovation process is related to significant costs and risks.
Hence, the knowledge of the factors that influence success is crucial
for technology driven companies. Taking a previously developed
framework of Critical Success Factors for radical technological
innovations as a reference model, we conducted a structured and
focused literature review of eleven standard books within the field of
technology and innovation management. With this approach we aim
to evaluate, expand, and clarify the set of Critical Success Factors
detailed in this framework. Overall, the set of factors and their
allocation to the main categories of the framework could be
confirmed. However, the factor organizational home is not
emphasized and discussed in most of the reviewed literature. On the
other hand, an additional factor that has not been part of the
framework is described to be important – strategy fit. Furthermore,
the factors strategic alliances and platform strategy appear in the
literature but in a different context compared to the reference model.
Abstract: This study and the field test comparisons were carried
out on the Algerian Derguna – Setif transmission systems. The
transmission line of normal voltage 225 kV is 65 km long,
transported and uses twin bundle conductors protected with two
shield wires of transposed galvanized steel. An iterative finite-element method is used to solve Poisons
equation. Two algorithms are proposed for satisfying the current
continuity condition and updating the space-charge density. A new approach to the problem of corona discharge in
transmission system has been described in this paper. The effect of
varying the configurations and wires number is also investigated. The
analysis of this steady is important in the design of HVDC
transmission lines. The potential and electric field have been
calculating in locations singular points of the system.