Abstract: This paper investigates the aerodynamic characters of a model ducted fan system, analyses the basic principle of the effect of thrust promotion and torque reduction, discovers the relationship between the revolutions per minute(RPM) of the fan and the characters of thrust, as well as system torque. Firstly a model ducted fan has been designed and manufactured according to the specific structure of flow field, then CFD simulation has been carried out to analyze such aerodynamics, finally bench tests have been used to validate the simulation results and system configuration.
Abstract: Components of a software system may be related in a
wide variety of ways. These relationships need to be represented in
software architecture in order develop quality software. In practice, software architecture is immensely challenging, strikingly
multifaceted, extravagantly domain based, perpetually changing,
rarely cost-effective, and deceptively ambiguous. This paper analyses
relations among the major components of software systems and
argues for using several broad categories for software architecture for
assessment purposes: strongly adequate, weakly adequate and
functionally adequate software architectures among other categories.
These categories are intended for formative assessments of
architectural designs.
Abstract: The innovative intelligent fuzzy weighted input
estimation method (FWIEM) can be applied to the inverse heat
transfer conduction problem (IHCP) to estimate the unknown
time-varying heat flux of the multilayer materials as presented in this
paper. The feasibility of this method can be verified by adopting the
temperature measurement experiment. The experiment modular may
be designed by using the copper sample which is stacked up 4
aluminum samples with different thicknesses. Furthermore, the
bottoms of copper samples are heated by applying the standard heat
source, and the temperatures on the tops of aluminum are measured by
using the thermocouples. The temperature measurements are then
regarded as the inputs into the presented method to estimate the heat
flux in the bottoms of copper samples. The influence on the estimation
caused by the temperature measurement of the sample with different
thickness, the processing noise covariance Q, the weighting factor γ ,
the sampling time interval Δt , and the space discrete interval Δx ,
will be investigated by utilizing the experiment verification. The
results show that this method is efficient and robust to estimate the
unknown time-varying heat input of the multilayer materials.
Abstract: A study was conducted to determine the effect of
feeding glycerol on dairy cows performance. Twenty four Holstein
Friesian crossbred (>87.5% Holstein Friesian) lactating dairy cows in
early lactation; averaging 13+2.4 kg of milk, 64+45 days in milk,
55+16 months old and 325+26 kg live weight, were stratified for
milk yield, days in milk, age, stage of lactation and body weight, and
then randomly allocated to three treatment groups. All cows were fed
approximate 8 kg of concentrate together with ad libitum corn silage
and freely access to clean water. Nil or 150 and 300g of glycerol
were supplemented to the cows according to treatment groups. All
cows consumed similar concentrate, corn silage and total DM and
NELP. There were no significant differences in DM intake, CP intake,
NELP intake, milk and milk composition yields. All cows had similar
fat, protein, lactose, solid not fat and total solid percentage. All cows
gain similar live weight. The present study indicated that,
supplementation of glycerol did not enhance milk yield, milk
composition and live weight change.
Abstract: The high temperature degree and uniform
Temperature Distribution (TD) on surface of cookware which contact
with food are effective factors for improving cookware application.
Additionally, the ability of pan material in retaining the heat and nonreactivity
with foods are other significant properties. It is difficult for
single material to meet a wide variety of demands such as superior
thermal and chemical properties. Multi-Layer Plate (MLP) makes
more regular TD. In this study the main objectives are to find the best
structure (single or multi-layer) and materials to provide maximum
temperature degree and uniform TD up side surface of pan. And also
heat retaining of used metals with goal of improving the thermal
quality of pan to economize the energy. To achieve this aim were
employed Finite Element Method (FEM) for analyzing transient
thermal behavior of applied materials. The analysis has been
extended for different metals, we achieved the best temperature
profile and heat retaining in Copper/ Stainless Steel MLP.
Abstract: A new generation of manufacturing machines
so-called MIMCA (modular and integrated machine control
architecture) capable of handling much increased complexity in
manufacturing control-systems is presented. Requirement for more
flexible and effective control systems for manufacturing machine
systems is investigated and dimensioned-which highlights a need for
improved means of coordinating and monitoring production
machinery and equipment used to- transport material. The MIMCA
supports simulation based on machine modeling, was conceived by
the authors to address the issues. Essentially MIMCA comprises an
organized unification of selected architectural frameworks and
modeling methods, which include: NISTRCS, UMC and Colored
Timed Petri nets (CTPN). The unification has been achieved; to
support the design and construction of hierarchical and distributed
machine control which realized the concurrent operation of reusable
and distributed machine control components; ability to handle
growing complexity; and support requirements for real- time control
systems. Thus MIMCA enables mapping between 'what a machine
should do' and 'how the machine does it' in a well-defined but
flexible way designed to facilitate reconfiguration of machine
systems.
Abstract: This research investigates the design of a low-cost 3D
spatial interaction approach using the Wii Remote for immersive
Head-Mounted Display (HMD) virtual reality. Current virtual reality
applications that incorporate the Wii Remote are either desktop
virtual reality applications or systems that use large screen displays.
However, the requirements for an HMD virtual reality system differ
from such systems. This is mainly because in HMD virtual reality,
the display screen does not remain at a fixed location. The user views
the virtual environment through display screens that are in front of
the user-s eyes and when the user moves his/her head, these screens
move as well. This means that the display has to be updated in realtime
based on where the user is currently looking. Normal usage of
the Wii Remote requires the controller to be pointed in a certain
direction, typically towards the display. This is too restrictive for
HMD virtual reality systems that ideally require the user to be able to
turn around in the virtual environment. Previous work proposed a
design to achieve this, however it suffered from a number of
drawbacks. The aim of this study is to look into a suitable method of
using the Wii Remote for 3D interaction in a space around the user
for HMD virtual reality. This paper presents an overview of issues
that had to be considered, the system design as well as experimental
results.
Abstract: High strength concrete has been used in situations
where it may be exposed to elevated temperatures. Numerous authors
have shown the significant contribution of polypropylene fiber to the
spalling resistance of high strength concrete.
When cement-based composite that reinforced by polypropylene
fibers heated up to 170 °C, polypropylene fibers readily melt and
volatilize, creating additional porosity and small channels in to the
matrix that cause the poor structure and low strength.
This investigation develops on the mechanical properties of mortar
incorporating polypropylene fibers exposed to high temperature.
Also effects of different pozzolans on strength behaviour of samples
at elevated temperature have been studied.
To reach this purpose, the specimens were produced by partial
replacement of cement with finely ground glass, silica fume and rice
husk ash as high reactive pozzolans. The amount of this replacement
was 10% by weight of cement to find the effects of pozzolans as a
partial replacement of cement on the mechanical properties of
mortars. In this way, lots of mixtures with 0%, 0.5%, 1% and 1.5% of
polypropylene fibers were cast and tested for compressive and
flexural strength, accordance to ASTM standard. After that
specimens being heated to temperatures of 300, 600 °C, respectively,
the mechanical properties of heated samples were tested.
Mechanical tests showed significant reduction in compressive
strength which could be due to polypropylene fiber melting. Also
pozzolans improve the mechanical properties of sampels.
Abstract: Calcium is a vital second messenger used in signal transduction. Calcium controls secretion, cell movement, muscular contraction, cell differentiation, ciliary beating and so on. Two theories have been used to simplify the system of reaction-diffusion equations of calcium into a single equation. One is excess buffer approximation (EBA) which assumes that mobile buffer is present in excess and cannot be saturated. The other is rapid buffer approximation (RBA), which assumes that calcium binding to buffer is rapid compared to calcium diffusion rate. In the present work, attempt has been made to develop a model for calcium diffusion under excess buffer approximation in neuron cells. This model incorporates the effect of [Na+] influx on [Ca2+] diffusion,variable calcium and sodium sources, sodium-calcium exchange protein, Sarcolemmal Calcium ATPase pump, sodium and calcium channels. The proposed mathematical model leads to a system of partial differential equations which have been solved numerically using Forward Time Centered Space (FTCS) approach. The numerical results have been used to study the relationships among different types of parameters such as buffer concentration, association rate, calcium permeability.
Abstract: Use of fly ash as a supplementary cementing material
in large volumes can bring both technological and economic benefits
for concrete industry. In this investigation mix proportions for high
volume fly ash concrete were determined at cement replacement
levels of 50%, 55%, 60% and 65% with low calcium fly ash. Flexural
and compressive strengths of different mixes were measured at ages
of 7, 28 and 90 days. Flexural strength of composite section prepared
from pavement quality and lean high volume fly ash concrete was
determined at the age of 28 days. High volume fly ash concrete mixes
exhibited higher rate of strength gain and age factors than
corresponding reference concrete mixes. The optimum cement
replacement level for pavement quality concrete was found to be
60%. The consideration of bond between pavement quality and lean
of high volume fly ash concrete will be beneficial in design of rigid
pavements.
Abstract: Ultrastructure of duodenum mucosa of irradiated rat
was studied versus dose rate of irradiation following exposure to
gamma rays from 60-Cobalt source. The animals were whole body
irradiated at two dose rates (1 Gy.mn-1 and 1 Gy.h-1) and three total
doses (1, 2 or 4 Gy) for each dose rate. 24 or 48 h after irradiation,
their small intestine was removed and samples of duodenum were
processed for observations under a transmission electron microscopy.
Samples of duodenum mucosa of control rats were processed in the
same way. For the lower dose rate of 1 Gy.h-1, main lesions
characteristic of apoptosis were detected within irradiated enterocytes
at a total dose of 2 Gy and 24 h after exposure. Necrosis was noted in
the samples, 48 h after exposition. For the higher dose rate of 1
Gy.mn-1, fewer changes were detected at all total doses 24 or 48 h
irradiation. Thus, it was shown that the appearance of radiationinduced
alterations varies not only with increasing total dose and
post-irradiation time but especially with decreasing dose rate.
Abstract: Rooted in the study of social functioning of space in architecture, Space Syntax (SS) and the more recent Network Pattern (NP) researches demonstrate the 'spatial structures' of city, i.e. the hierarchical patterns of streets, junctions and alley ends. Applying SS and NP models, planners can conceptualize the real city-s patterns. Although, both models yield the optimal path of the city their underpinning displays of the city-s spatial configuration differ. The Axial Map analyzes the topological non-distance-based connectivity structure, whereas, the Central-Node Map and the Shortcut-Path Map, in contrast, analyze the metrical distance-based structures. This research contrasts and combines them to understand various forms of city-s structures. It concludes that, while they reveal different spatial structures, Space Syntax and Network Pattern urban models support each the other. Combining together they simulate the global access and the locally compact structures namely the central nodes and the shortcuts for the city.
Abstract: After reporting a literature review on Customer
Relationship Management (CRM) and knowledge management, some
important issued arise, in particular related to the lack of success of
CRM strategies implementation. The paper contributes to this
proposing an integrated model of CRM success taking into account
complementary factors such as organizational factors, technology,
knowledge management and customer orientation.
Abstract: Early detection of dementia by testing the spatial
memory can be applied using a virtual environment. This paper
presents guidelines on how to design a virtual environment
specifically for elderly in early detection of dementia. The specific
design needs to be considered because the effectiveness of the
technology relies on the ability of the end user to use it. The primary
goal of these guidelines is to promote accessibility. Based on these
guidelines, a virtual simulation was developed and evaluated. The
results on usability of acceptance and satisfaction that are tested on
young (control group) and elderly participants indicate that these
guidelines are reliable and useful for use with elderly people.
Abstract: The introduction of haptic elements in a graphic user interfaces are becoming more widespread. Since haptics are being introduced rapidly into computational tools, investigating how these models affect Human-Computer Interaction would help define how to integrate and model new modes of interaction. The interest of this paper is to discuss and investigate the issues surrounding Haptic and Graphic User Interface designs (GUI) as separate systems, as well as understand how these work in tandem. The development of these systems is explored from a psychological perspective, based on how usability is addressed through learning and affordances, defined by J.J. Gibson. Haptic design can be a powerful tool, aiding in intuitive learning. The problems discussed within the text is how can haptic interfaces be integrated within a GUI without the sense of frivolity. Juxtaposing haptics and Graphic user interfaces has issues of motivation; GUI tends to have a performatory process, while Haptic Interfaces use affordances to learn tool use. In a deeper view, it is noted that two modes of perception, foveal and ambient, dictate perception. These two modes were once thought to work in tandem, however it has been discovered that these processes work independently from each other. Foveal modes interpret orientation is space which provide for posture, locomotion, and motor skills with variations of the sensory information, which instructs perceptions of object-task performance. It is contended, here, that object-task performance is a key element in the use of Haptic Interfaces because exploratory learning uses affordances in order to use an object, without meditating an experience cognitively. It is a direct experience that, through iteration, can lead to skill-sets. It is also indicated that object-task performance will not work as efficiently without the use of exploratory or kinesthetic learning practices. Therefore, object-task performance is not as congruently explored in GUI than it is practiced in Haptic interfaces.
Abstract: Sunflower stalks were analysed for chemical
compositions: pentosan 15.84%, holocellulose 70.69%,
alphacellulose 45.74%, glucose 27.10% and xylose 7.69% based on
dry weight of 100-g raw material. The most optimum condition for
steam explosion pretreatment was as follows. Sunflower stalks were
cut into small pieces and soaked in 0.02 M H2SO4 for overnight.
After that, they were steam exploded at 207 C and 21 kg/cm2 for 3
minutes to fractionate cellulose, hemicellulose and lignin. The
resulting hydrolysate, containing hemicellulose, and cellulose pulp
contained xylose sugar at 2.53% and 7.00%, respectively.The pulp
was further subjected to enzymatic saccharification at 50 C, pH 4.8 citrate buffer) with pulp/buffer 6% (w/w)and Celluclast 1.5L/pulp
2.67% (w/w) to obtain single glucose with maximum yield 11.97%.
After fixed-bed fermentation under optimum condition using
conventional yeast mixtures to produce bioethanol, it indicated
maximum ethanol yield of 0.028 g/100 g sunflower stalk.
Abstract: We present a label-free biosensor based on
electrochemical impedance spectroscopy for the detection of proinflammatory
cytokine Tumor Necrosis Factor (TNF-α). Secretion of
TNF-α has been correlated to the onset of various diseases including
rheumatoid arthritis, Crohn-s disease etc. Gold electrodes were
patterned on a silicon substrate and self assembled monolayer of
dithiobis-succinimidyl propionate was used to develop the biosensor
which achieved a detection limit of ~57fM. A linear relationship was
also observed between increasing TNF-α concentrations and chargetransfer
resistance within a dynamic range of 1pg/ml – 1ng/ml.
Abstract: This paper focuses on the use of project work as a
pretext for applying the conventions of writing, or the correctness of
mechanics, usage, and sentence formation, in a content-based class in
a Rajabhat University. Its aim was to explore to what extent the
student teachers’ academic achievement of the basic writing features
against the 70% attainment target after the use of project is. The
organization of work around an agreed theme in which the students
reproduce language provided by texts and instructors is expected to
enhance students’ correct writing conventions. The sample of the
study comprised of 38 fourth-year English major students. The data
was collected by means of achievement test and student writing
works. The scores in the summative achievement test were analyzed
by mean score, standard deviation, and percentage. It was found that
the student teachers do more achieve of practicing mechanics and
usage, and less in sentence formation. The students benefited from
the exposure to texts during conducting the project; however, their
automaticity of how and when to form phrases and clauses into
simple/complex sentences had room for improvement.
Abstract: On-line handwritten scripts are usually dealt with pen tip traces from pen-down to pen-up positions. Time evaluation of the pen coordinates is also considered along with trajectory information. However, the data obtained needs a lot of preprocessing including filtering, smoothing, slant removing and size normalization before recognition process. Instead of doing such lengthy preprocessing, this paper presents a simple approach to extract the useful character information. This work evaluates the use of the counter- propagation neural network (CPN) and presents feature extraction mechanism in full detail to work with on-line handwriting recognition. The obtained recognition rates were 60% to 94% using the CPN for different sets of character samples. This paper also describes a performance study in which a recognition mechanism with multiple thresholds is evaluated for counter-propagation architecture. The results indicate that the application of multiple thresholds has significant effect on recognition mechanism. The method is applicable for off-line character recognition as well. The technique is tested for upper-case English alphabets for a number of different styles from different peoples.
Abstract: The modified Claus process is commonly used in oil
refining and gas processing to recover sulfur and destroy
contaminants formed in upstream processing. A Claus furnace feed
containing a relatively low concentration of H2S may be incapable of
producing a stable flame. Also, incomplete combustion of
hydrocarbons in the feed can lead to deterioration of the catalyst in
the reactors due to soot or carbon deposition. Therefore, special
consideration is necessary to achieve the appropriate overall sulfur
recovery. In this paper, some configurations available to treat lean
acid gas streams are described and the most appropriate ones are
studied to overcome low H2S concentration problems. As a result,
overall sulfur recovery is investigated for feed preheating and hot gas
configurations.