Abstract: In this research, a systematic investigation was carried out to determine the optimum conditions of HDS reactor. Moreover, a suitable model was developed for a rigorous RTO (real time optimization) loop of HDS (Hydro desulfurization) process. A systematic experimental series was designed based on CCD (Central Composite design) and carried out in the related pilot plant to tune the develop model. The designed variables in the experiments were Temperature, LHSV and pressure. However, the hydrogen over fresh feed ratio was remained constant. The ranges of these variables were respectively equal to 320-380ºC, 1- 21/hr and 50-55 bar. a power law kinetic model was also developed for our further research in the future .The rate order and activation energy , power of reactant concentration and frequency factor of this model was respectively equal to 1.4, 92.66 kJ/mol and k0=2.7*109 .
Abstract: Land with low pH soil spread widely in Indonesia
can be used for soybean (Glycine max) cultivation, however the
production is low. The use of acid tolerant soybean and acidaluminium
tolerant nitrogen-fixing bacteria formula was an
alternative way to increase soybean productivity on acid soils.
Bradyrhizobium japonicum is one of the nitrogen fixing bacteria
which can symbiose with soybean plants through root nodule
formation. Most of the nitrogen source required by soybean plants
can be provided by this symbiosis. This research was conducted to
study the influence of acid-aluminium tolerant B. japonicum strain
BJ 11 formula using peat as carrier on growth of Tanggamus and
Anjasmoro cultivar soybean planted on acid soil fields (pH 5.0-
5.5). The results showed that the inoculant was able to increase the
growth and production of soybean which were grown on fields acid
soil at Sukadana (Lampung) and Tanah Laut (South Kalimantan),
Indonesia.
Abstract: Nano-MgO was successfully deposited on titania using deposition-precipitation method. The catalyst produced was characterised using FTIR, XRD, BET and XRF and its activity was tested on the transesterification reaction of soybean oil to biodiesel. The catalyst activity improved when the reaction temperature was increasedfrom 150 and 225 OC. It was also observed that increasing the reaction time above 1h had no significant benefit on conversion. The stability fixed MgO on TiO2 was investigated using XRF and ICP-OES. It was observed that MgO loss during the reaction was between 0.5-2.3 percent and that there was no correlation between the reaction temperature and the MgO loss.
Abstract: Continuous pyrolysis of Cogongrass by control
temperature in the novel pyrolysis reactor were conducted at three
difference temperatures 400, 450 and 500°C. Preliminary calculate of
the product yields founded the liquid yield of Cogongrass was
highest of 41.45 %, at 500 oC. Indicated that the liquid yield from
Cogongrass had good received yields because it gave over 40 % and
its produced more liquid than that solid and gas. The compounds
detected in bio-oil from Cogongrass showed the functional group,
especially; Phenol, Phenol, 2,5-dimethyl, Phenol, 3-methyl, 2-
methyl-1,3-oxathiofane, Benzene,1-ethyl-4-methoxy, 2-Cyclopenten-
1-one,2,3-dimethyl, 2- Cyclopenten-1- one, 3-Methyl.
Abstract: Soil mechanics is a traditional course in any
university. Management of lab classes is one of the main issues to
deliver a proper outline. In Curtin University, different methods
applied to check the efficiency of these methods. One of them was
mainly rely on demonstration and the other one mainly on involving
students in running tests. Comparison between these delivery
methods also are outlined in summary section. The recommendation
also made that the more satisfaction is reachable while the students
engaged.
Abstract: Vinegar or sour wine is a product of alcoholic and
subsequent acetous fermentation of sugary precursors derived from
several fruits or starchy substrates. This delicious food additive and
supplement contains not less than 4 grams of acetic acid in 100 cubic
centimeters at 20°C. Among the large number of bacteria that are
able to produce acetic acid, only few genera are used in vinegar
industry most significant of which are Acetobacter and
Gluconobacter. In this research we isolated and identified an
Acetobacter strain from Iranian apricot, a very delicious and sensitive
summer fruit to decay, we gathered from fruit's stores in Isfahan,
Iran. The main culture media we used were Carr, GYC, Frateur and
an industrial medium for vinegar production. We isolated this strain
using a novel miniature fermentor we made at Pars Yeema
Biotechnologists Co., Isfahan Science and Technology Town (ISTT),
Isfahan, Iran. The microscopic examinations of isolated strain from
Iranian apricot showed gram negative rods to cocobacilli. Their
catalase reaction was positive and oxidase reaction was negative and
could ferment ethanol to acetic acid. Also it showed an acceptable
growth in 5%, 7% and 9% ethanol concentrations at 30°C using
modified Carr media after 24, 48 and 96 hours incubation
respectively. According to its tolerance against high concentrations of
ethanol after four days incubation and its high acetic acid production,
8.53%, after 144 hours, this strain could be considered as a suitable
industrial strain for a production of a new type of vinegar, apricot
vinegar, with a new and delicious taste. In conclusion this is the first
report of isolation and identification of an Acetobacter strain from
Iranian apricot with a very good tolerance against high ethanol
concentrations as well as high acetic acid productivity in an
acceptable incubation period of time industrially. This strain could be
used in vinegar industry to convert apricot spoilage to a beneficiary
product and mentioned characteristics have made it as an amenable
strain in food and agricultural biotechnology.
Abstract: Studying alternative raw materials for biodiesel production is of major importance. The use of mixtures with incorporation of wastes is an environmental friendly alternative and might reduce biodiesel production costs. The objective of the present work was: (i) to study biodiesel production using waste frying oil mixed with pork lard and (ii) to understand how mixture composition influences biodiesel quality. Biodiesel was produced by transesterification and quality was evaluated through determination of several parameters according to EN 14214. The weight fraction of lard in the mixture varied from 0 to 1 in 0.2 intervals. Biodiesel production yields varied from 81.7 to 88.0 (wt%), the lowest yields being the ones obtained using waste frying oil and lard alone as raw materials. The obtained products fulfilled most of the determined quality specifications according to European biodiesel quality standard EN 14214. Minimum purity (96.5 wt%) was closely obtained when waste frying oil was used alone and when 0.2% of lard was incorporated in the raw material (96.3 wt%); however, it ranged from 93.9 to 96.3 (wt%) being always close to the limit. From the evaluation of the influence of mixture composition in biodiesel quality, it was possible to establish a model to be used for predicting some parameters of biodiesel resulting from mixtures of waste frying oil with lard when different lard contents are used.
Abstract: The development of biomimetic micro-aerial-vehicles
(MAVs) with flapping wings is the future trend in military/domestic
field. The successful flight of MAVs is strongly related to the
understanding of unsteady aerodynamic performance of low Reynolds
number airfoils under dynamic flapping motion. This study explored
the effects of flapping frequency, stroke amplitude, and the inclined
angle of stroke plane on lift force and thrust force of a bio-inspiration
corrugated airfoil with 33 full factorial design of experiment and
ANOVA analysis. Unsteady vorticity flows over a corrugated thin
airfoil executing flapping motion are computed with time-dependent
two-dimensional laminar incompressible Reynolds-averaged
Navier-Stokes equations with the conformal hybrid mesh. The tested
freestream Reynolds number based on the chord length of airfoil as
characteristic length is fixed of 103. The dynamic mesh technique is
applied to model the flapping motion of a corrugated airfoil. Instant
vorticity contours over a complete flapping cycle clearly reveals the
flow mechanisms for lift force generation are dynamic stall, rotational
circulation, and wake capture. The thrust force is produced as the
leading edge vortex shedding from the trailing edge of airfoil to form a
reverse von Karman vortex. Results also indicated that the inclined
angle is the most significant factor on both the lift force and thrust
force. There are strong interactions between tested factors which mean
an optimization study on parameters should be conducted in further
runs.
Abstract: This work presents the first results from the long-term experiment, which is focused on the impact of intensive rainfall and long period of drought on microbial activities in soil. Fifteen lysimeters were prepared in the area of our interest. This area is a protection zone of underground source of drinking water. These lysimeters were filed with topsoil and subsoil collected in this area and divided into two groups. These groups differ in fertilization and amount of water received during the growing season. Amount of microbial biomass and leaching of mineral nitrogen and phosphates were chosen as main indicators of microbial activities in soil. Content of mineral nitrogen and phosphates was measured in soil solution, which was collected from each lysimeters. Amount of microbial biomass was determined in soil samples that were taken from the lysimeters before and after the long period of drought and intensive rainfall.
Abstract: In the oil and gas industry, energy prediction can help
the distributor and customer to forecast the outgoing and incoming
gas through the pipeline. It will also help to eliminate any
uncertainties in gas metering for billing purposes. The objective of
this paper is to develop Neural Network Model for energy
consumption and analyze the performance model. This paper
provides a comprehensive review on published research on the
energy consumption prediction which focuses on structures and the
parameters used in developing Neural Network models. This paper is
then focused on the parameter selection of the neural network
prediction model development for energy consumption and analysis
on the result. The most reliable model that gives the most accurate
result is proposed for the prediction. The result shows that the
proposed neural network energy prediction model is able to
demonstrate an adequate performance with least Root Mean Square
Error.
Abstract: This study aims to initiate sustainable water management for tourist accommodations in Amphawa, Samut Songkram Province, Thailand. Wastewater generated by tourist accommodation was conducted in 10 homestays and resorts in Amphawa during August – October, 2011. The prominent parameters which are of pH, Dissolved Oxygen (DO), Biochemical Oxygen Demand (BOD), Fat Oil and Grease (FOG), Nitrate (No3-), and Phosphate (PO43-) were conducted monthly. The results revealed that some parameters were over national water quality standard (Class II). Especially, 90% of tourist accommodations have been recorded that FOG was over the standard of wastewater quality from accommodation (group I: total room of accommodation less than 200 rooms). Therefore, grease trap and natural treatment should be utilized in tourist accommodations in order to reduce the discharged of fat, oil, and grease from tourism activities. In addition, number of tourists also relate statistically with BOD and Nitrate at 0.05 level of significance.
Abstract: Investigation of soil properties like Cation Exchange
Capacity (CEC) plays important roles in study of environmental
reaserches as the spatial and temporal variability of this property
have been led to development of indirect methods in estimation of
this soil characteristic. Pedotransfer functions (PTFs) provide an
alternative by estimating soil parameters from more readily available
soil data. 70 soil samples were collected from different horizons of
15 soil profiles located in the Ziaran region, Qazvin province, Iran.
Then, multivariate regression and neural network model (feedforward
back propagation network) were employed to develop a
pedotransfer function for predicting soil parameter using easily
measurable characteristics of clay and organic carbon. The
performance of the multivariate regression and neural network model
was evaluated using a test data set. In order to evaluate the models,
root mean square error (RMSE) was used. The value of RMSE and
R2 derived by ANN model for CEC were 0.47 and 0.94 respectively,
while these parameters for multivariate regression model were 0.65
and 0.88 respectively. Results showed that artificial neural network
with seven neurons in hidden layer had better performance in
predicting soil cation exchange capacity than multivariate regression.
Abstract: The study of soil for agriculture purposes has
remained the main focus of research since the beginning of civilization as humans- food related requirements remained closely linked with the soil. The study of soil has generated an interest
among the researchers for very similar other reasons including transmission, reflection and refraction of signals for deploying
wireless underground sensor networks or for the monitoring of objects on (or in ) soil in the form of better understanding of soil
electromagnetic characteristics properties. The moisture content has
been very instrumental in such studies as it decides on the resistance of the soil, and hence the attenuation on signals traveling through soil
or the attenuation the signals may suffer upon their impact on soil. This work is related testing and characterizing a measurement circuit
meant for the detection of moisture level content in soil.
Abstract: This paper presents a mean for reducing the torque
variation during the revolution of a vertical-axis wind turbine
(VAWT) by increasing the blade number. For this purpose, twodimensional
CDF analysis have been performed on a straight-bladed
Darreius-type rotor. After describing the computational model, a
complete campaign of simulations based on full RANS unsteady
calculations is proposed for a three, four and five-bladed rotor
architecture characterized by a NACA 0025 airfoil. For each
proposed rotor configuration, flow field characteristics are
investigated at several values of tip speed ratio, allowing a
quantification of the influence of blade number on flow geometric
features and dynamic quantities, such as rotor torque and power.
Finally, torque and power curves are compared for the analyzed
architectures, achieving a quantification of the effect of blade number
on overall rotor performance.
Abstract: This paper presents a study of laminar to turbulent transition on a profile specifically designed for wind turbine blades, the DU91-W2-250, which belongs to a class of wind turbine dedicated airfoils, developed by Delft University of Technology. A comparison between the experimental behavior of the airfoil studied at Delft wind tunnel and the numerical predictions of the commercial CFD solver ANSYS FLUENT® has been performed. The prediction capabilities of the Spalart-Allmaras turbulence model and of the γ-θ Transitional model have been tested. A sensitivity analysis of the numerical results to the spatial domain discretization has also been performed using four different computational grids, which have been created using the mesher GAMBIT®. The comparison between experimental measurements and CFD results have allowed to determine the importance of the numerical prediction of the laminar to turbulent transition, in order not to overestimate airfoil friction drag due to a fully turbulent-regime flow computation.
Abstract: In many applications there is a broad variety of
information relevant to a focal “object" of interest, and the fusion of such heterogeneous data types is desirable for classification and
categorization. While these various data types can sometimes be treated as orthogonal (such as the hull number, superstructure color,
and speed of an oil tanker), there are instances where the inference and the correlation between quantities can provide improved fusion
capabilities (such as the height, weight, and gender of a person). A
service-oriented architecture has been designed and prototyped to
support the fusion of information for such “object-centric" situations.
It is modular, scalable, and flexible, and designed to support new data sources, fusion algorithms, and computational resources without affecting existing services. The architecture is designed to simplify
the incorporation of legacy systems, support exact and probabilistic entity disambiguation, recognize and utilize multiple types of
uncertainties, and minimize network bandwidth requirements.
Abstract: Generation of electricity from coal has increased over
the years in the United States and around the world. Burning of coal
results in annual production of upwards of 100 millions tons (United
States only) of coal combustion products (CCPs). Only about a third
of these products are being used to create new products while the
remainder goes to landfills. Application of CCPs mixed with
composted organic materials onto soil can improve the soil-s
physico-chemical conditions and provide essential plant nutritients.
Our objective was to create plant growth media utilizing CCPs and
compost in way which maximizes the use of these products and, at
the same time, maintain good plant growth. Media were formulated
by adding composted organic matter (COM) to CCPs at ratios
ranging from 2:8 to 8:2 (v/v). The quality of these media was
evaluated by measuring their physical and chemical properties and
their effect on plant growth. We tested the media by 1) measuring
their physical and chemical properties and 2) the growth of three
plant species in the experimental media: wheat (Triticum sativum),
tomato (Lycopersicum esculentum) and marigold (Tagetes patula).
We achieved significantly (p < 0.001) higher growth (7-130%) in the
experimental media containing CCPs compared to a commercial mix.
The experimental media supplied adequate plant nutrition as no
fertilization was provided during the experiment. Based on the
results, we recommend the use of CCPs and composts for the
creation of plant growth media.
Abstract: In the present study, the oleaginous fungus
Mortierella alpina CBS 754.68 was screened for arachidonic
acidproduction using inexpensive agricultural by-products as
substrate. Four oilcakes were analysed to choose the best substrate
among them. Sunflower oilcake was the most effective substrate for
ARA production followed by soybean, colza and olive oilcakes. In
the next step, seven variables including substrate particle size,
moisture content, time, temperature, yeast extract supply, glucose
supply and glutamate supply were surveyed and effective variables
for ARA production were determined using a Plackett-Burman
screening design. Analysis results showed that time (12 days),
substrate particle size (1-1.4 mm) and temperature (20ºC) were the
most effective variables for the highest level of ARA production
respectively.
Abstract: Rhizopus oligosporus was used in the present study
for the production of protease enzyme under SSF. Sunflower meal
was used as by-product of oil industry incorporated with organic salts
was employed for the production of protease enzyme. The main
purpose of the present was to study different parameters of protease
productivity, its yields and to optimize basal fermentation conditions.
The optimal conditions found for protease production using
sunflower meal as a substrate in the present study were inoculum size
(1%), substrate (Sunflower meal), substrate concentration (20 g), pH
(3), cultivation period (72 h), incubation temperature (35oC),
substrate to diluent-s ratio (1:2) and tween 81 (1 mL). The maximum
production of protease in the presence of cheaper substrate at low
concentration and stability at acidic pH, these characteristics make
the strain and its enzymes useful in different industry.
Abstract: This article simulates the wind generator set which has
two fault bearing collar rail destruction and the gear box oil leak fault.
The electric current signal which produced by the generator, We use
Empirical Mode Decomposition (EMD) as well as Fast Fourier
Transform (FFT) obtains the frequency range-s signal figure and
characteristic value. The last step is use a kind of Artificial Neural
Network (ANN) classifies which determination fault signal's type and
reason. The ANN purpose of the automatic identification wind
generator set fault..