Abstract: The eco-efficient use of “waste" makes sense from
economic, social, and environmental perspectives. By efficiency diverting “waste" products back into useful and/or profitable inputs,
industries and entire societies can reap the benefits of improved financial profit, decreased environmental degradation, and overall
well-being of humanity.
In this project, several material flows at
Company Limited were investigated. Principles of "industrial ecology" were applied to improve the management of waste rubbers that are used in the jewelry manufacturing process. complete this project, a brief engineering analysis stream, and investigated eco-efficient principles for more efficient
handling of the materials and wastes were conducted, and the result were used to propose implementation strategies.
Abstract: Describes the current situation of educational Robotics
"the State of the art" its concept, its evolution their niches of
opportunity, academic and business and the importance of education
and academic outreach. It shows that the development of high-tech
automated educational materials influence the teaching-learning
process and that communication between machines and humans is a
reality.
Abstract: Electro Chemical Discharge Machining (ECDM) is an
emerging hybrid machining process used in precision machining of hard and brittle non-conducting materials. The present paper gives a
critical review on materials machined by ECDM under the prevailing machining conditions; capability indicators of the process are
reported. Some results obtained while performing experiments in micro-channeling on soda lime glass using ECDM are also presented. In these experiments, Tool Wear (TW) and Material Removal (MR)
were studied using design of experiments and L–4 orthogonal array. Experimental results showed that the applied voltage was the most influencing parameter in both MR and TW studies. Field
emission scanning electron microscopy (FESEM) results obtained on the microchannels confirmed the presence of micro-cracks, primarily responsible for MR. Chemical etching was also seen along the edges.
The Energy dispersive spectroscopy (EDS) results were used to detect the elements present in the debris and specimens.
Abstract: This paper presents a NDT by infrared thermography with excitation CO2 Laser, wavelength of 10.6 μm. This excitation is the controllable heating beam, confirmed by a preliminary test on a wooden plate 1.2 m x 0.9 m x 1 cm. As the first practice, this method is applied to detecting the defect in CFRP heated by the Laser 300 W during 40 s. Two samples 40 cm x 40 cm x 4.5 cm are prepared, one with defect, another one without defect. The laser beam passes through the lens of a deviation device, and heats the samples placed at a determinate position and area. As a result, the absence of adhesive can be detected. This method displays prominently its application as NDT with the composite materials. This work gives a good perspective to characterize the laser beam, which is very useful for the next detection campaigns.
Abstract: The removal of hydrogen sulphide is required for reasons of health, odour problems, safety and corrosivity problems. The means of removing hydrogen sulphide mainly depend on its concentration and kind of medium to be purified. The paper deals with a method of hydrogen sulphide removal from the air by its catalytic oxidation to elemental sulphur with the use of Fe-EDTA complex. The possibility of obtaining fibrous filtering materials able to remove small concentrations of H2S from the air were described. The base of these materials is fibrous ion exchanger with Fe(III)- EDTA complex immobilized on their functional groups. The complex of trivalent iron converts hydrogen sulphide to elemental sulphur. Bivalent iron formed in the reaction is oxidized by the atmospheric oxygen, so complex of trivalent iron is continuously regenerated and the overall process can be accounted as pseudocatalytic. In the present paper properties of several fibrous catalysts based on ion exchangers with different chemical nature (weak acid,weak base and strong base) were described. It was shown that the main parameters affecting the process of catalytic oxidation are:concentration of hydrogen sulphide in the air, relative humidity of the purified air, the process time and the content of Fe-EDTA complex in the fibres. The data presented show that the filtering layers with anion exchange package are much more active in the catalytic processes of hydrogen sulphide removal than cation exchanger and inert materials. In the addition to the nature of the fibres relative air humidity is a critical factor determining efficiency of the material in the air purification from H2S. It was proved that the most promising carrier of the Fe-EDTA catalyst for hydrogen sulphide oxidation are Fiban A-6 and Fiban AK-22 fibres.
Abstract: Dual phase steels (DPS)s have a microstructure
consisting of a hard second phase called Martensite in the soft Ferrite
matrix. In recent years, there has been interest in dual-phase steels,
because the application of these materials has made significant usage;
particularly in the automotive sector Composite microstructure of
(DPS)s exhibit interesting characteristic mechanical properties such
as continuous yielding, low yield stress to tensile strength
ratios(YS/UTS), and relatively high formability; which offer
advantages compared with conventional high strength low alloy
steels(HSLAS). The research dealt with the characterization of
damage in (DPS)s. In this study by review the mechanisms of failure
due to volume fraction of martensite second phase; a new method is
introduced to identifying the mechanisms of failure in the various
phases of these types of steels. In this method the acoustic emission
(AE) technique was used to detect damage progression. These failure
mechanisms consist of Ferrite-Martensite interface decohesion and/or
martensite phase fracture. For this aim, dual phase steels with
different volume fraction of martensite second phase has provided by
various heat treatment methods on a low carbon steel (0.1% C), and
then AE monitoring is used during tensile test of these DPSs. From
AE measurements and an energy ratio curve elaborated from the
value of AE energy (it was obtained as the ratio between the strain
energy to the acoustic energy), that allows detecting important
events, corresponding to the sudden drops. These AE signals events
associated with various failure mechanisms are classified for ferrite
and (DPS)s with various amount of Vm and different martensite
morphology. It is found that AE energy increase with increasing Vm.
This increasing of AE energy is because of more contribution of
martensite fracture in the failure of samples with higher Vm. Final
results show a good relationship between the AE signals and the
mechanisms of failure.
Abstract: The hot deformation behavior of high strength low
alloy (HSLA) steels with different chemical compositions under hot
working conditions in the temperature range of 900 to 1100℃ and
strain rate range from 0.1 to 10 s-1 has been studied by performing a
series of hot compression tests. The dynamic materials model has been
employed for developing the processing maps, which show variation
of the efficiency of power dissipation with temperature and strain rate.
Also the Kumar-s model has been used for developing the instability
map, which shows variation of the instability for plastic deformation
with temperature and strain rate. The efficiency of power dissipation
increased with decreasing strain rate and increasing temperature in the
steel with higher Cr and Ti content. High efficiency of power
dissipation over 20 % was obtained at a finite strain level of 0.1 under
the conditions of strain rate lower than 1 s-1 and temperature higher
than 1050 ℃ . Plastic instability was expected in the regime of
temperatures lower than 1000 ℃ and strain rate lower than 0.3 s-1. Steel
with lower Cr and Ti contents showed high efficiency of power
dissipation at higher strain rate and lower temperature conditions.
Abstract: The dental composites are preferably used as filling
materials due to their esthetic appearances. Nevertheless one of the
major problems, during the application of the dental composites, is
shape change named as “polymerisation shrinkage" affecting clinical
success of the dental restoration while photo-polymerisation.
Polymerisation shrinkage of composites arises basically from the
formation of a polymer due to the monomer transformation which
composes of an organic matrix phase. It was sought, throughout this
study, to detect and evaluate the structural polymerisation shrinkage
of prepared dental composites in order to optimize the effects of
various fillers included in hydroxyapatite (HA)-reinforced dental
composites and hence to find a means to modify the properties of
these dental composites prepared with defined parameters. As a
result, the shrinkage values of the experimental dental composites
were decreased by increasing the filler content of composites and the
composition of different fillers used had effect on the shrinkage of
the prepared composite systems.
Abstract: Aluminothermic rail welding was from the beginning
a great success because its low price even in 1895 in Germany. This
method is now, widely used all over the world for the railways
construction, maintenance and modernization. Instructions give you
guidelines for preparing papers for conferences or journals.
After 1989, the welding needs of the potentials beneficiaries
(Romanian Railways, Urban Transportation Companies) keep raise
because of the railways maintenance and modernization necessity.
The main materials that determine the Thermit (T) composition
result from manufacturing scraps all over the country. This can help
the environment by consuming these scraps.
The Romanian need for alumino-thermic welding is now by 11300
per year, and in a favourable economical environment, this amount
can reach 30000 units.
This paper tries to show the effect of two types of modifiers
introduced in the T composition on the structure and properties of an
alumino-thermic welding.
Abstract: This work relates the development of an optical fiber
(OF) sensor for the detection and quantification of single walled
carbon nanotubes in aqueous solutions. The developed OF displays a
compact design, it requires less expensive materials and equipment
as well as low volume of sample (0.2 mL). This methodology was
also validated by the comparison of its analytical performance with
that of a standard methodology based on ultraviolet-visible
spectroscopy. The developed OF sensor follows the general SDS
calibration proposed for OF sensors as a more suitable calibration
fitting compared with classical calibrations.
Abstract: The modeling of inelastic behavior of plastic materials requires measurements providing information on material response to different multiaxial loading conditions. Different triaxiality conditions and values of Lode parameters have to be
covered for complex description of the material plastic behavior.
Samples geometries providing material plastic behavoiur over the range of interest are proposed with the use of FEM analysis. Round samples with 3 different notches and smooth surface are used
together with butterfly type of samples tested at angle ranging for 0 to
90°. Identification of ductile damage parameters is carried out on
the basis of obtained experimental data for austenitic stainless steel.
The obtained material plastic damage parameters are subsequently applied to FEM simulation of notched CT normally samples used for
fracture mechanics testing and results from the simulation are
compared with real tests.
Abstract: In this paper we present discretization and decomposition methods for a multi-component transport model of a chemical vapor deposition (CVD) process. CVD processes are used to manufacture deposition layers or bulk materials. In our transport model we simulate the deposition of thin layers. The microscopic model is based on the heavy particles, which are derived by approximately solving a linearized multicomponent Boltzmann equation. For the drift-process of the particles we propose diffusionreaction equations as well as for the effects of heat conduction. We concentrate on solving the diffusion-reaction equation with analytical and numerical methods. For the chemical processes, modelled with reaction equations, we propose decomposition methods and decouple the multi-component models to simpler systems of differential equations. In the numerical experiments we present the computational results of our proposed models.
Abstract: Experiments have been carried out at the Latvia
University of Agriculture Department of Food Technology. The aim
of this work was to assess the effect of thermal treatment in flexible
retort pouch packaging on the quality of potatoes’ produce during the
storage time. Samples were evaluated immediately after retort
thermal treatment; and following 1; 2; 3 and 4 storage months at the
ambient temperature of +18±2ºC in vacuum packaging from
polyamide/polyethylene (PA/PE) and aluminum/polyethylene
(Al/PE) film pouches with barrier properties. Experimentally the
quality of the potatoes’ produce in dry butter and mushroom
dressings was characterized by measuring pH, hardness, color,
microbiological properties and sensory evaluation. The sterilization
was effective in protecting the produce from physical, chemical, and
microbial quality degradation. According to the study of obtained
data, it can be argued that the selected product processing technology
and packaging materials could be applied to provide the safety and
security during four-month storage period.
Abstract: A numbers of important developments have led to an
increasing attractiveness for very high speed electrical machines
(either motor or generator). Specifically the increasing switching
speed of power electronics, high energy magnets, high strength
retaining materials, better high speed bearings and improvements in
design analysis are the primary drivers in a move to higher speed. The
design challenges come in the mechanical design both in terms of
strength and resonant modes and in the electromagnetic design
particularly in respect of iron losses and ac losses in the various
conducting parts including the rotor. This paper describes detailed
design work which has been done on a 50,000 rpm, 50kW permanent
magnet( PM) synchronous machine. It describes work on
electromagnetic and rotor eddy current losses using a variety of
methods including both 2D finite element analysis
Abstract: Gamboge disorder (GD) or fruit damage by the yellow sap is a major problem in mangosteen. Mangosteen plants varied in the level of GD, from very low or non GD to low, moderate and high GD. However it was difficult to differentiate between GD and non GD plants because evaluation of the disorder is strongly influenced by environment. In this study we investigated the usefulness of primer designed from bioinformatics related to cell wall strength, termed as MCWS, to predict GD. Plant materials used were 28 mangosteen plants selected based on percentage of GD categorized as high, moderate, low and very low or non GD. The result showed that the specific DNA fragments were absent in the high GD accessions. The MCWS marker suggests as a novel polymorphic marker for GD in mangosteen as well as a marker for detect variability in mangosteen as apomictic plant.
Abstract: Two novel hydrodesulfurization (HDS) catalysts:
FeN4/C and FeN2/C, were prepared using an impregnation-pyrolysis
method. The two materials were investigated as catalysts for
hydrodesulfurization (HDS) and hydrodearomitization (HDA) of
model compounds. The turnover frequency of the two FeN catalysts
is comparable to (FeN4/C) or even higher (FeN2/C) than that of
MoNi/Al2O3. The FeN4/C catalyst also exhibited catalytic activity
toward HDA.
Abstract: The importance for manipulating an incorporated
scaffold and directing cell behaviors is well appreciated for tissue
engineering. Here, we developed newly nano-topographic oxidized
silicon nanosponges capable of being various chemical modifications
to provide much insight into the fundamental biology of how cells
interact with their surrounding environment in vitro. A wet etching
technique is exerted to allow us fabricated the silicon nanosponges in a
high-throughput manner. Furthermore, various organo-silane
chemicals enabled self-assembled on the surfaces by vapor deposition.
We have found that Chinese hamster ovary (CHO) cells displayed
certain distinguishable morphogenesis, adherent responses, and
biochemical properties while cultured on these chemical modified
nano-topographic structures in compared with the planar oxidized
silicon counterparts, indicating that cell behaviors can be influenced
by certain physical characteristic derived from nano-topography in
addition to the hydrophobicity of contact surfaces crucial for cell
adhesion and spreading. Of particular, there were predominant
nano-actin punches and slender protrusions formed while cells were
cultured on the nano-topographic structures. This study shed potential
applications of these nano-topographic biomaterials for controlling
cell development in tissue engineering or basic cell biology research.
Abstract: The present paper concerns with the influence of fiber
packing on the transverse plastic properties of metal matrix
composites. A micromechanical modeling procedure is used to
predict the effective mechanical properties of composite materials at
large tensile and compressive deformations. Microstructure is
represented by a repeating unit cell (RUC). Two fiber arrays are
considered including ideal square fiber packing and random fiber
packing defined by random sequential algorithm. The
micromechanical modeling procedure is implemented for
graphite/aluminum metal matrix composite in which the
reinforcement behaves as elastic, isotropic solids and the matrix is
modeled as an isotropic elastic-plastic solid following the von Mises
criterion with isotropic hardening and the Ramberg-Osgood
relationship between equivalent true stress and logarithmic strain.
The deformation is increased to a considerable value to evaluate both
elastic and plastic behaviors of metal matrix composites. The yields
strength and true elastic-plastic stress are determined for
graphite/aluminum composites.
Abstract: The efficacy of the separate mixing of four tropical spicy and medicinal plant products: Dennettia tripetala Baker (pepper fruit), Eugenia aromatica Hook (clove), Piper guineense (Schum and Thonn) (black pepper) and Monodora myristica (Dunal) (African nut-meg) with a household vegetable oil was evaluated under tropical storage conditions for the control and reproductive performance of Dermestes maculatus (De Geer) (hide beetle) and Necroba rufipes (De Geer) (copra beetle) on African catfish, Clarias gariepinus (Burchell). Each of the plant materials was pulverized into powder and applied as a mix of 1ml of oil and plant powder at 2.5, 5.0, 7.5 and 10.0g per 100g of dried fish, and allowed to dry for 6h. Each of the four oil-mixed powder treatments evoked significant (P < 05) mortalities of the two insects compared with the control (oil only) at 1, 3 and 7 days post treatment. The oil-powder mixture dosages did not prevent insect egg hatchability but while the emergent larvae on the treated samples died, the emergent larvae in the control survived into adults. The application of oil-mixed powders effectively suppressed the emergence of the larvae of the beetles. Similarly, each of the oil-powder mixtures significantly reduced weight loss in smoked fish that were exposed to D. maculatus and N. rufipes when compared to the control (P < 05). The results of this study suggest that the plant powders rather than the domestic oil demonstrated protective ability against the fish beetles and confirm the efficacy of the plant products as pest control agents.
Abstract: This paper deals with the analysis of active constrained layer damping (ACLD) of doubly curved laminated composite shells using active fiber composite (AFC) materials. The constraining layer of the ACLD treatment has been considered to be made of the AFC materials. A three dimensional energy based finite element model of the smart doubly curved laminated composite shell integrated with a patch of such ACLD treatment has been developed to demonstrate the performance of the patch on enhancing the damping characteristics of the doubly curved laminated composite shells. Particular emphasis has been placed on studying the effect of variation of piezoelectric fiber orientation angle in the constraining AFC layer on the control authority of the ACLD patch.