Abstract: Electrolytic dissolution characteristics of UO2 and
SIMFUEL electrodes were studied at several potentials in carbonate
solutions of a high concentration at several pHs. The electrolytic
uranium dissolution was much affected by a corrosion product of
UO2CO3 generated at the electrode during the dissolution in carbonate
solution. The corrosion product distorted the voltammogram at UO2
and SIMFUEL electrodes in the potential region of oxygen evolution
and increased the overpotential of oxygen evolution at the electrode.
The effective dissolution in a carbonate solution could be obtained at
an applied potential such as +4 V (vs SSE) or more which had an
overpotential of oxygen evolution high enough to rupture the
corrosion product on the electrode surface.
Abstract: The experimental and theoretical results of a ZVS
(Zero Voltage Switching) isolated flyback DC-DC converter using
multilayered coreless PCB step down 2:1 transformer are presented.
The performance characteristics of the transformer are shown which
are useful for the parameters extraction. The measured energy
efficiency of the transformer is found to be more than 94% with the
sinusoidal input voltage excitation. The designed flyback converter
has been tested successfully upto the output power level of 10W,
with a switching frequency in the range of 2.7MHz-4.3MHz. The
input voltage of the converter is varied from 25V-40V DC.
Frequency modulation technique is employed by maintaining
constant off time to regulate the output voltage of the converter. The
energy efficiency of the isolated flyback converter circuit under ZVS
condition in the MHz frequency region is found to be approximately
in the range of 72-84%. This paper gives the comparative results in
terms of the energy efficiency of the hard switched and soft switched
flyback converter in the MHz frequency region.
Abstract: Restructured electricity markets may provide
opportunities for producers to exercise market power maintaining
prices in excess of competitive levels. In this paper an oligopolistic
market is presented that all Generation Companies (GenCos) bid in a
Cournot model. Genetic algorithm (GA) is applied to obtain
generation scheduling of each GenCo as well as hourly market
clearing prices (MCP). In order to consider network constraints a
multiperiod framework is presented to simulate market clearing
mechanism in which the behaviors of market participants are
modelled through piecewise block curves. A mixed integer linear
programming (MILP) is employed to solve the problem. Impacts of
market clearing process on participants- characteristic and final
market prices are presented. Consequently, a novel multi-objective
model is addressed for security constrained optimal bidding strategy
of GenCos. The capability of price-maker GenCos to alter MCP is
evaluated through introducing an effective-supply curve. In addition,
the impact of exercising market power on the variation of market
characteristics as well as GenCos scheduling is studied.
Abstract: In the micro and nano-technology industry, the
«clean-rooms» dedicated to manufacturing chip, are equipped with
the most sophisticated equipment-tools. There use a large number of
resources in according to strict specifications for an optimum
working and result. The distribution of «utilities» to the production is
assured by teams who use a supervision tool.
The studies show the interest to control the various parameters of
production or/and distribution, in real time, through a reliable and
effective supervision tool. This document looks at a large part of the
functions that the supervisor must assure, with complementary
functionalities to help the diagnosis and simulation that prove very
useful in our case where the supervised installations are complexed
and in constant evolution.
Abstract: Polyurethane foams (PUF) has been prepared from
vegetable; soybean based polyols. They were characterized into
flexible and semi rigid polyurethane foam. This work is directed to
production of flexible polyurethane foams by a process involving the
reaction of mixture of 2,4- and 2,6-Toluene di Isocyanate isomers,
with portion of to blends of soy polyols with petroleum polyol in the
presence of other ingredients such as blowing agents, silicone
surfactants and accelerating agents. Additon of chain extender
improves the property then further decreases the properties on further
addition of the same. The objective of this work was to study the
effect of chain extender and role of phosphoric acid catalyst to the
final properties and correlate the morphology image with mechanical
properties of these foams.
Abstract: This paper numerically investigates the effects of input
speed on the overall dynamic characteristics of a multi-body system
with differently located revolute clearance joints without friction. A
typical planar slider-crank mechanism is used as a demonstration case
in which the effects of the input speed on the dynamic performance
of the mechanism with a revolute clearance joint between the crank
and connecting rod, and between the connecting rod and slider are
separately investigated with comprehensive observations numerically
presented. It is observed that, changing the driving speed of a multibody
system makes the behavior of the system to change from
either periodic to chaotic, or chaotic to periodic depending on which
joint has clearance. The location of the clearance revolute joint and
the operating speed of a multi-body system play a crucial role in
predicting accurately the dynamic responses of the system. Therefore
the dynamic behavior of one clearance revolute joint cannot be used
as a general case for a mechanical system.
Abstract: A comparative evaluation of acute toxicity of
synthesized nano silvers using two different procedures (biological
and chemical reduction methods) and silver ions on bacteria
Vibrio fischeri was investigated. The bacterial light inhibition test as
a toxicological endpoint was used by applying of a homemade
luminometer. To compare the toxicity effects as a quantitative
parameter, a nominal effective concentrations (EC) of chemicals and
a susceptibility constant (Z-value) of bacteria, after 5 min and 30 min
exposure times, were calculated. After 5 and 30 min contact times,
the EC50 values of two silver nanoparticles and the EC20 values were
about similar. It demonstrates that toxicity of silvers was independent
of their procedure. The EC values of nanoparticles were larger than
those of the silver ions. The susceptibilities(Z- Values) of V.fischeri
(L/mg) to the silver ions were greater than those of the nano silvers.
According to the EC and Z values, the toxicity of silvers decreased in
the following order: Silver ions >> silver nanoparticles from
chemical reduction method ~ silver nanoparticles from biological
method.
Abstract: Real-time measurement of applied forces, like tension, compression, torsion, and bending moment, identifies the transferred energies being applied to the bottomhole assembly (BHA). These forces are highly detrimental to measurement/logging-while-drilling tools and downhole equipment. Real-time measurement of the dynamic downhole behavior, including weight, torque, bending on bit, and vibration, establishes a real-time feedback loop between the downhole drilling system and drilling team at the surface. This paper describes the numerical analysis of the strain data acquired by the measurement tool at different locations on the strain pockets. The strain values obtained by FEA for various loading conditions (tension, compression, torque, and bending moment) are compared against experimental results obtained from an identical experimental setup. Numerical analyses results agree with experimental data within 8% and, therefore, substantiate and validate the FEA model. This FEA model can be used to analyze the combined loading conditions that reflect the actual drilling environment.
Abstract: The objective of the research is to study and compare
response surface designs: Central composite designs (CCD), Box-
Behnken designs (BBD), Small composite designs (SCD), Hybrid
designs, and Uniform shell designs (USD) over sets of reduced models
when the design is in a spherical region for 3 and 4 design variables.
The two optimality criteria ( D and G ) are considered which larger
values imply a better design. The comparison of design optimality
criteria of the response surface designs across the full second order
model and sets of reduced models for 3 and 4 factors based on the
two criteria are presented.
Abstract: In this paper, a novel method using Bees Algorithm is proposed to determine the optimal allocation of FACTS devices for maximizing the Available Transfer Capability (ATC) of power transactions between source and sink areas in the deregulated power system. The algorithm simultaneously searches the FACTS location, FACTS parameters and FACTS types. Two types of FACTS are simulated in this study namely Thyristor Controlled Series Compensator (TCSC) and Static Var Compensator (SVC). A Repeated Power Flow with FACTS devices including ATC is used to evaluate the feasible ATC value within real and reactive power generation limits, line thermal limits, voltage limits and FACTS operation limits. An IEEE30 bus system is used to demonstrate the effectiveness of the algorithm as an optimization tool to enhance ATC. A Genetic Algorithm technique is used for validation purposes. The results clearly indicate that the introduction of FACTS devices in a right combination of location and parameters could enhance ATC and Bees Algorithm can be efficiently used for this kind of nonlinear integer optimization.
Abstract: Low oxygen content vanadium powder was
prepared by hydrogenation dehydrogenization (HDH). The
effect of purification treatment on hydrogen absorption kinetics
of dendritic vanadium was tested, and the effects of milling
technique on powder yield and grain size were studied. The
crystal phase, oxygen and nitrgen content, and grain size of
prepared powder were characterized and analyzed by X-ray
diffraction (XRD), oxygen and nitrogen analyzer and grain size
analyzer. The results show that the alkaline cleaning can
improve the hydrogen absorption of vanadium. The yield of
vanadium hydride powder can reach as high as 90% by 4h
ball-milling, The resultant product also have an oxygen content
less than 600μg/g, and the grain size is smaller than 37μm.
Meanwhile, the XRD results show that the phase of hydride
vanadium powder is mainly VH0.81. After a hydrogen
desorption treatment in vacuum at 700Ôäâ, the phase of the
powder converts into V and a little of V2H.
Abstract: In this paper we present the algorithm which allows
us to have an object tracking close to real time in Full HD videos.
The frame rate (FR) of a video stream is considered to be between
5 and 30 frames per second. The real time track building will be
achieved if the algorithm can follow 5 or more frames per second. The
principle idea is to use fast algorithms when doing preprocessing to
obtain the key points and track them after. The procedure of matching
points during assignment is hardly dependent on the number of points.
Because of this we have to limit pointed number of points using the
most informative of them.
Abstract: Along with the increased morbidity of glaucoma or
diabetic retinitis pigmentosa, etc., number of people with vision loss is
also increasing in Japan. It is difficult for the visually impaired to learn
and acquire braille because most of them are middle-aged. In addition,
number of braille teachers are not sufficient and reducing in Japan, and
this situation makes more difficult for the visually impaired. Therefore,
we research and develop a Web-based e-learning program for tactile
braille, that cooperate with braille display and voice assistance.
Abstract: This experiment was performed with the purpose of
investigating effect of additional blend of probiotics Saccharomyces
cerevisiae and Lactobacillus acidophilus on plasma fatty acid profiles
particularly conjugated linoleic acid (CLA) in growing goats fed corn
silage, and selected the optimal levels of the probiotics for further study.
Twenty-four growing crossbred (Thai native x Anglo-Nubian) goats that
weighed (14.2 ± 2.3) kg, aged about 6 months, were purchased and
allocated to 4 treatments according to Randomized Complete Block
Design (RCBD) with 6 goats in each treatment. The blocks were made by
weight into heavy, medium, and light goats and each of the treatments
contained two goats from each of the blocks. In the mean time, ruminal
average pH unaffected, but the NH3-N and also plasma urea nitrogen
(p0.05) were raised, but propionic
proportion (p0.05) were reduced in
concurrent with raise of acetic proportion and resultantly C2:C3 ratio
(p>0.05). On plasma fatty acid profiles, total saturated fatty acids
(p>0.05) was increased, and contrasted with decrease of C15:0
(p0.05), and C18-C22 polyunsaturated fatty acids
(p
Abstract: The Ministry of Defense (MoD) spends hundreds of
millions of dollars on software to support its infrastructure, operate
its weapons and provide command, control, communications,
computing, intelligence, surveillance, and reconnaissance (C4ISR)
functions. These and other all new advanced systems have a common
critical component is information technology. Defense and
Aerospace environment is continuously striving to keep up with
increasingly sophisticated Information Technology (IT) in order to
remain effective in today-s dynamic and unpredictable threat
environment. This makes it one of the largest and fastest growing
expenses of Defense. Hundreds of millions of dollars spent a year on
IT projects. But, too many of those millions are wasted on costly
mistakes. Systems that do not work properly, new components that
are not compatible with old once, trendily new applications that do
not really satisfy defense needs or lost though poorly managed
contracts.
This paper investigates and compiles the effective strategies that
aim to end exasperation with low returns and high cost of
Information Technology Acquisition for defense; it tries to show how
to maximize value while reducing time and expenditure.
Abstract: This paper presents the comparison study of current control techniques for shunt active power filter. The hysteresis current control, the delta modulation control and the carrier-based PWM control are considered in the paper. The synchronous detection method is used to calculate the reference currents for shunt active power filter. The simulation results show that the carrier-based PWM control technique provides the minimum %THD value of the source currents compared with other comparable techniques after compensation. However, the %THD values of all three techniques can follow the IEEE std.519-1992.
Abstract: Quasigroups are algebraic structures closely related to
Latin squares which have many different applications. The
construction of block cipher is based on quasigroup string
transformation. This article describes a block cipher based
Quasigroup of order 256, suitable for fast software encryption of
messages written down in universal ASCII code. The novelty of this
cipher lies on the fact that every time the cipher is invoked a new set
of two randomly generated quasigroups are used which in turn is
used to create a pair of quasigroup of dual operations. The
cryptographic strength of the block cipher is examined by calculation
of the xor-distribution tables. In this approach some algebraic
operations allows quasigroups of huge order to be used without any
requisite to be stored.
Abstract: In this paper, the design of a multiple U-slotted microstrip patch antenna with frequency selective surface (FSS) as a superstrate for WLAN and WiMAX applications is presented. The proposed antenna is designed by using substrate FR4 having permittivity of 4.4 and air substrate. The characteristics of the antenna are designed and evaluated the performance of modelled antenna using CST Microwave studio. The proposed antenna dual resonant frequency has been achieved in the band of 2.37-2.55 GHz and 3.4-3.6 GHz. Because of the impact of FSS superstrate, it is found that the bandwidths have been improved from 6.12% to 7.35 % and 3.7% to 5.7% at resonant frequencies 2.45 GHz and 3.5 GHz, respectively. The maximum gain at the resonant frequency of 2.45 and 3.5 GHz are 9.3 and 11.33 dBi, respectively.
Abstract: Alumina matrix composites with addition of hexagonal boron nitride (hBN), acting as solid lubricant, were produced. Main purpose of solid lubricants is to dispose the necessity of using cooling lubricants in machining process. Hot pressing was used as a consolidating process for Al2O3-x%wt.hBN (x=1/ 2,5/ 5 /7,5 /10) composites. Properties of sinters such as relative density, hardness, Young-s modulus and fracture toughness were examined. Obtained samples characterize by high relative density. Hardness and fracture toughness values allow the use of alumina – hBN composites for machining steels even in hardened condition. However it was observed that high weight content of hBN can negatively influence the mechanical properties of composites.
Abstract: Manufacturing components of fiber-reinforced
thermoplastics requires three steps: heating the matrix, forming and
consolidation of the composite and terminal cooling the matrix. For
the heating process a pre-determined temperature distribution through
the layers and the thickness of the pre-consolidated sheets is
recommended to enable forming mechanism. Thus, a design for the
heating process for forming composites with thermoplastic matrices
is necessary. To obtain a constant temperature through thickness and
width of the sheet, the heating process was analyzed by the help of
the finite element method. The simulation models were validated by
experiments with resistance thermometers as well as with an infrared
camera. Based on the finite element simulation, heating methods for
infrared radiators have been developed. Using the numeric
simulation many iteration loops are required to determine the process
parameters. Hence, the initiation of a model for calculating relevant
process parameters started applying regression functions.