Abstract: A simple method for the simultaneous determination
of hippuric acid and benzoic acid in urine using reversed-phase high
performance liquid chromatography was described. Chromatography
was performed on a Nova-Pak C18 (3.9 x 150 mm) column with a
mobile phase of mixed solution methanol: water: acetic acid
(20:80:0.2) and UV detection at 254 nm. The calibration curve was
linear within concentration range at 0.125 to 6.0 mg/ml of hippuric
acid and benzoic acid. The recovery, accuracy and coefficient
variance of hippuric acid were 104.54%, 0.2% and 0.2% respectively
and for benzoic acid were 98.48%, 1.25% and 0.60% respectively.
The detection limit of this method was 0.01ng/l for hippuric acid and
0.06ng/l for benzoic acid. This method has been applied to the
analysis of urine samples from the suspected of toluene abuser or
glue sniffer among secondary school students at Johor Bahru.
Abstract: Sedimentation formation is a complex hydraulic phenomenon that has emerged as a major operational and maintenance consideration in modern hydraulic engineering in general and river engineering in particular. Sediments accumulation along the river course and their eventual storage in a form of islands affect water intake in the canal systems that are fed by the storage reservoirs. Without proper management, sediment transport can lead to major operational challenges in water distribution system of arid regions like the Dez and Hamidieh command areas. The paper aims to investigate sedimentation in the Western Canal of Dez Diversion Weir using the SHARC model and compare the results with the two intake structures of the Hamidieh dam in Iran using SSIIM model. The objective was to identify the factors which influence the process, check reliability of outcome and provide ways in which to mitigate the implications on operation and maintenance of the structures. Results estimated sand and silt bed loads concentrations to be 193 ppm and 827ppm respectively. This followed ,ore or less similar pattern in Hamidieh where the sediment formation impeded water intake in the canal system. Given the available data on average annual bed loads and average suspended sediment loads of 165ppm and 837ppm in the Dez, there was a significant statistical difference (16%) between the sand grains, whereas no significant difference (1.2%) was find in the silt grain sizes. One explanation for such finding being that along the 6 Km river course there was considerable meandering effects which explains recent shift in the hydraulic behavior along the stream course under investigation. The sand concentration in downstream relative to present state of the canal showed a steep descending curve. Sediment trapping on the other hand indicated a steep ascending curve. These occurred because the diversion weir was not considered in the simulation model. The comparative study showed very close similarities in the results which explains the fact that both software can be used as accurate and reliable analytical tools for simulation of the sedimentation in hydraulic engineering.
Abstract: Female breast cancer is the second in frequency after cervical cancer. Surgery is the most common treatment for breast cancer, followed by chemotherapy as a treatment of choice. Although effective, it causes serious side effects. Controlled-release drug delivery is an alternative method to improve the efficacy and safety of the treatment. It can release the dosage of drug between the minimum effect concentration (MEC) and minimum toxic concentration (MTC) within tumor tissue and reduce the damage of normal tissue and the side effect. Because an in vivo experiment of this system can be time-consuming and labor-intensive, a mathematical model is desired to study the effects of important parameters before the experiments are performed. Here, we describe a 3D mathematical model to predict the release of doxorubicin from pluronic gel to treat human breast cancer. This model can, ultimately, be used to effectively design the in vivo experiments.
Abstract: Anaerobic treatment has many advantages over other
biological method particularly when used to treat complex
wastewater such as petroleum refinery wastewater. In this study two
Up-flow Anaerobic Sludge Blanket (UASB) reactors were operated
in parallel to treat six volumetric organic loads (0.58, 1.21, 0.89,
2.34, 1.47 and 4.14 kg COD/m3·d) to evaluate the chemical oxygen
demand (COD) removal efficiency. The reactors were continuously
adapting to the changing of operation condition with increase in the
removal efficiency or slight decrease until the last load which was
more than two times the load, at which the reactor stressed and the
removal efficiency decreased to 75% with effluent concentration of
1746 mg COD/L. Other parameters were also monitored such as pH,
alkalinity, volatile fatty acid and gas production rate. The UASB
reactor was suitable to treat petroleum refinery wastewater and the
highest COD removal rate was 83% at 1215 kg/m3·d with COD
concentration about 356 mg/L in the effluent.
Abstract: Biological reactions of individuals of a testing animal
to toxic substance are unique and can be used as an indication of the
existing of toxic substance. However, to distinguish such phenomenon
need a very complicate system and even more complicate to analyze
data in 3 dimensional. In this paper, a system to evaluate in vitro
biological activities to acute toxicity of stochastic self-affine
non-stationary signal of 3D goldfish swimming by using fractal
analysis is introduced. Regular digital camcorders are utilized by
proposed algorithm 3DCCPC to effectively capture and construct 3D
movements of the fish. A Critical Exponent Method (CEM) has been
adopted as a fractal estimator. The hypothesis was that the swimming
of goldfish to acute toxic would show the fractal property which
related to the toxic concentration. The experimental results supported
the hypothesis by showing that the swimming of goldfish under the
different toxic concentration has fractal properties. It also shows that
the fractal dimension of the swimming related to the pH value of FD Ôëê
0.26pH + 0.05. With the proposed system, the fish is allowed to swim
freely in all direction to react to the toxic. In addition, the trajectories
are precisely evaluated by fractal analysis with critical exponent
method and hence the results exhibit with much higher degree of
confidence.
Abstract: Five vegetables (spinach, lettuce, cabbage, tomato, and onion) were freshly harvested from the Alau Dam and Gongulong agricultural areas for the determination of some organochlorine pesticide residues (o, p-DDE, p,p’-DDD, o,p’-DDD, p,p’-DDT, α-BHC, γ-BHC, metoxichlor, lindane, endosulfan dieldrin, and aldrin.) Soil samples were also collected at different depths for the determination of the above pesticides. Samples collection and preparation were conducted using standard procedures. The concentrations of all the pesticides in the soil and vegetable samples were determined using GC/MS SHIMADZU (GC-17A) equipped with electron capture detector (ECD). The highest concentration was that of p,p’-DDD (132.4±13.45µg/g) which was observed in the leaf of cabbage, while the lowest concentration was that of p,p’-DDT (2.34µg/g) was observed in the root of spinach. Similar trends were observed at the Gongulong agricultural area, with p,p’-DDD having the highest concentration of 153.23µg/g in the leaf of cabbage, while the lowest concentration was that of p,p’-DDT (12.45µg/g) which was observed in the root of spinach. α-BHC, γ-BHC, Methoxychlor, and lindane were detected in all the vegetable samples studied. The concentrations of all the pesticides in the soil samples were observed to be higher at a depth of 21-30cm, while the lowest concentrations were observed at a depth of 0-10cm. The concentrations of all the pesticides in the vegetables and soil samples from the two agricultural sites were observed to be at alarming levels, much higher than the maximum residue limits (MRLs) and acceptable daily intake values (ADIs) .The levels of the pesticides observed in the vegetables and soil samples investigated, are of such a magnitude that calls for special attention and laws to regulate the use and circulation of such chemicals. Routine monitoring of pesticide residues in these study areas is necessary for the prevention, control and reduction of environmental pollution, so as to minimize health risks.
Abstract: As the Textile Industry is the second largest industry
in Egypt and as small and medium-sized enterprises (SMEs) make up
a great portion of this industry therein it is essential to apply the
concept of Cleaner Production for the purpose of reducing pollution.
In order to achieve this goal, a case study concerned with ecofriendly
stone-washing of jeans-garments was investigated. A raw
material-substitution option was adopted whereby the toxic
potassium permanganate and sodium sulfide were replaced by the
environmentally compatible hydrogen peroxide and glucose
respectively where the concentrations of both replaced chemicals
together with the operating time were optimized. In addition, a
process-rationalization option involving four additional processes
was investigated. By means of criteria such as product quality,
effluent analysis, mass and heat balance; and cost analysis with the
aid of a statistical model, a process optimization treatment revealed
that the superior process optima were 50%, 0.15% and 50min for
H2O2 concentration, glucose concentration and time, respectively.
With these values the superior process ought to reduce the annual
cost by about EGP 105 relative to the currently used conventional
method.
Abstract: In this study, the kinetics of osmotic dehydration of melons (Tille variety) in a ternary system followed by air-drying for preserving melons in the summer to be used in the winter were investigated. The effect of different osmotic solution concentrations 30, 40 and 50% (w/w) of sucrose with 10% NaCl salt and fruit to solution ratios 1:4, 1:5 and 1:6 on the mass transfer kinetics during osmotic dehydration of melon in ternary solution namely sucrosesalt- water followed by air-drying were studied. The diffusivity of water during air-drying was enhanced after the fruit samples were immersed in the osmotic solution after 60 min. Samples non-treated and pre-treated during one hour in osmotic solutions with 60% (w/w) of sucrose with 10% NaCl salt and fruit to solution ratio of 1:4 were dried in a hot air-dryer at 60oC (2 m/s) until equilibrium was achieved.
Abstract: The accelerated sonophotocatalytic degradation of
Reactive Red (RR) 120 dye under visible light using dye sensitized
TiO2 activated by ultrasound has been carried out. The effect of
sonolysis, photocatalysis and sonophotocatalysis under visible light
has been examined to study the influence on the degradation rates by
varying the initial substrate concentration, pH and catalyst loading to
ascertain the synergistic effect on the degradation techniques.
Ultrasonic activation contributes degradation through cavitation
leading to the splitting of H2O2 produced by both photocatalysis and
sonolysis. This results in the formation of oxidative species, such as
singlet oxygen (1O2) and superoxide (O2
-●) radicals in the presence of
oxygen. The increase in the amount of reactive radical species which
induce faster oxidation of the substrate and degradation of
intermediates and also the deaggregation of the photocatalyst are
responsible for the synergy observed under sonication. A
comparative study of photocatalysis and sonophotocatalysis using
TiO2, Hombikat UV 100 and ZnO was also carried out.
Abstract: Study was conducted to determine the concentration of
copper, cadmium, lead and zinc in Cabomba furcata that found
abundance in Lake Chini. This aquatic plant was collected randomly
within the lake for heavy metal determination. Water quality
measurement was undertaken in situ for temperature, pH,
conductivity and dissolved oksigen using portable multi sensor probe
YSI model 556. The C. furcata was digested using wet digestion
method and heavy metal concentrations were analysed using Atomic
Absorption Spectrometer (AAS) Perkin Elmer 4100B (flame
method). Result of water quality classify Lake Chini between class II
to class III using Malaysian Water Quality Standard. According to
this standard, Lake Chini has moderate quality, which normal for
natural lake. Heavy metal concentrations in C.furcata were low and
found to be lower than the critical toxic value in aquatic plants. Oneway
ANOVA test indicated the heavy metal concentrations in
C.furcata were significantly differ between sampling location. Water
quality and heavy metal concentrations indicates that Lake Chini was
not receives anthropogenic load from nearby activities.
Abstract: This paper reports the three-phase (gas + liquid +
hydrate) equilibrium pressure versus temperature data for a (O3 + O2 +
CO2 + H2O) system for developing the hydrate-based technology to
preserve ozone, a chemically unstable substance, for various
industrial, medical and consumer uses. These data cover the
temperature range from 272 K to 277 K, corresponding to pressures
from 1.6 MPa to 3.1 MPa, for each of the three different (O3 +
O2)-to-CO2 or O2-to-CO2 molar ratios in the gas phase, which are
approximately 4 : 6, 5 : 5, respectively. The mole fraction of ozone in
the gas phase was ~0.03 , which are the densest ozone fraction to
artificially form O3 containing hydrate ever reported in the literature.
Based on these data, the formation of hydrate containing
high-concentration ozone, as high as 1 mass %, will be expected.
Abstract: The main aim of Supply Chain Management (SCM) is
to produce, distribute, logistics and deliver goods and equipment in
right location, right time, right amount to satisfy costumers, with
minimum time and cost waste. So implementing techniques that
reduce project time and cost, and improve productivity and
performance is very important. Emerging technologies such as the
Radio Frequency Identification (RFID) are now making it possible to
automate supply chains in a real time manner and making them more
efficient than the simple supply chain of the past for tracing and
monitoring goods and products and capturing data on movements of
goods and other events. This paper considers concepts, components
and RFID technology characteristics by concentration of warehouse
and inventories management. Additionally, utilization of RFID in the
role of improving information management in supply chain is
discussed. Finally, the facts of installation and this technology-s
results in direction with warehouse and inventory management and
business development will be presented.
Abstract: The Spiral development model has been used
successfully in many commercial systems and in a good number of
defense systems. This is due to the fact that cost-effective
incremental commitment of funds, via an analogy of the spiral model
to stud poker and also can be used to develop hardware or integrate
software, hardware, and systems. To support adaptive, semantic
collaboration between domain experts and knowledge engineers, a
new knowledge engineering process, called Spiral_OWL is proposed.
This model is based on the idea of iterative refinement, annotation
and structuring of knowledge base. The Spiral_OWL model is
generated base on spiral model and knowledge engineering
methodology. A central paradigm for Spiral_OWL model is the
concentration on risk-driven determination of knowledge engineering
process. The collaboration aspect comes into play during knowledge
acquisition and knowledge validation phase. Design rationales for the
Spiral_OWL model are to be easy-to-implement, well-organized, and
iterative development cycle as an expanding spiral.
Abstract: The present study based on removal of natural dyes of
Roselle petals, then used Roselle petals powder (RPP) as an
adsorbent for the removal of methylene blue dye (as a typical cationic
or basic dye) from aqueous solutions. The present study shows that
used Roselle petals powder exhibit adsorption trend for the dye. The
adsorption processes were carried out at various conditions of
temperatures ranging from 278 to 338 K ± 2 K , concentrations,
processing time and a wide range of pH between 2.5-11. Adsorption
isotherm equations such as Freundlich, and Langmuir were applied to
calculate the values of respective constants. Adsorption study was
found that the currently introduced adsorbent can be used to remove
cationic dyes such as methylene blue from aqueous solutions.
Abstract: Free convection effects and heat transfer due to a pulsating point heat source embedded in an infinite, fluid saturated, porous dusty medium are studied analytically. Both velocity and temperature fields are discussed in the form of series expansions in the Rayleigh number, for both the fluid and particle phases based on the mean heat generation rate from source and on the permeability of the porous dusty medium. This study is carried out by assuming the Rayleigh number small and the validity of Darcy-s law. Analytical expressions for both phases are obtained for second order mean in both velocity and temperature fields and evolution of different wave patterns are observed in the fluctuating part. It has been observed that, at the vicinity of the origin, the second order mean flow is influenced only by relaxation time of dust particles and not by dust concentration.
Abstract: Acute kidney injury (AKI) is a new worldwide public
health problem. A diagnosis of this disease using creatinine is still a
problem in clinical practice. Therefore, a measurement of biomarkers
responsible for AKI has received much attention in the past couple
years. Cytokine interleukin-18 (IL-18) was reported as one of the
early biomarkers for AKI. The most commonly used method to
detect this biomarker is an immunoassay. This study used a planar
platform to perform an immunoassay using fluorescence for
detection. In this study, anti-IL-18 antibody was immobilized onto a
microscope slide using a covalent binding method. Make-up samples
were diluted at the concentration between 10 to 1000 pg/ml to create
a calibration curve. The precision of the system was determined
using a coefficient of variability (CV), which was found to be less
than 10%. The performance of this immunoassay system was
compared with the measurement from ELISA.
Abstract: The value of overall oxygen transfer Coefficient
(KLa), which is the best measure of oxygen transfer in water through
aeration, is obtained by a simple approach, which sufficiently
explains the utility of the method to eliminate the discrepancies due
to inaccurate assumption of saturation dissolved oxygen
concentration. The rate of oxygen transfer depends on number of
factors like intensity of turbulence, which in turns depends on the
speed of rotation, size, and number of blades, diameter and
immersion depth of the rotor, and size and shape of aeration tank, as
well as on physical, chemical, and biological characteristic of water.
An attempt is made in this paper to correlate the overall oxygen
transfer Coefficient (KLa), as an independent parameter with other
influencing parameters mentioned above. It has been estimated that
the simulation equation developed predicts the values of KLa and
power with an average standard error of estimation of 0.0164 and
7.66 respectively and with R2 values of 0.979 and 0.989 respectively,
when compared with experimentally determined values. The
comparison of this model is done with the model generated using
Computational fluid dynamics (CFD) and both the models were
found to be in good agreement with each other.
Abstract: Tea is consumed by a big part of the world-s
population. It has an enormous importance for the Turkish culture.
Nearly it is brewed every morning and evening at the all houses. Also it is consumed with lemon wedge. Habitual drinking of tea
infusions may significantly contribute to daily dietary requirements of elements.
Different instrumental techniques are used for determination of
these elements. But atomic and mass spectroscopic methods are preferred most. In these study chromium, iron and selenium contents
after the hot water brewing of black and green tea were determined
by Optical Emission Spectroscopy (ICP-OES). Furthermore, effect
of lemon addition on chromium, iron and selenium concentration tea
infusions is investigated.
Results of the investigation showed that concentration of
chromium, iron and selenium increased in black tea with lemon addition. On the other hand only selenium is increased with lemon
addition in green tea. And iron concentration is not detected in green
tea but its concentration is determined as 1.420 ppm after lemon addition.
Abstract: The aim of this paper is to investigate the influence of
market share and diversification on the nonlife insurers- performance.
The underlying relationships have been investigated in different
industries and different disciplines (economics, management...), still,
no consistency exists either in the magnitude or statistical
significance of the relationship between market share (and
diversification as well) on one side and companies- performance on
the other side. Moreover, the direction of the relationship is also
somewhat questionable. While some authors find this relationship to
be positive, the others reveal its negative association. In order to test
the influence of market share and diversification on companies-
performance in Croatian nonlife insurance industry for the period
from 1999 to 2009, we designed an empirical model in which we
included the following independent variables: firms- profitability
from previous years, market share, diversification and control
variables (i.e. ownership, industrial concentration, GDP per capita,
inflation). Using the two-step generalized method of moments
(GMM) estimator we found evidence of a positive and statistically
significant influence of both, market share and diversification, on
insurers- profitability.
Abstract: The utilization of cheese whey as a fermentation
substrate to produce bio-ethanol is an effort to supply bio-ethanol
demand as a renewable energy. Like other process systems, modeling
is also required for fermentation process design, optimization and
plant operation. This research aims to study the fermentation process
of cheese whey by applying mathematics and fundamental concept in
chemical engineering, and to investigate the characteristic of the
cheese whey fermentation process. Steady state simulation results for
inlet substrate concentration of 50, 100 and 150 g/l, and various
values of hydraulic retention time, showed that the ethanol
productivity maximum values were 0.1091, 0.3163 and 0.5639 g/l.h
respectively. Those values were achieved at hydraulic retention time
of 20 hours, which was the minimum value used in this modeling.
This showed that operating reactor at low hydraulic retention time
was favorable. Model of bio-ethanol production from cheese whey
will enhance the understanding of what really happen in the
fermentation process.