Abstract: The present paper deals with the most adopted technical
solutions for the enhancement of the lift force of a wing. In fact,
during several flight conditions (such as take off and landing), the
lift force needs to be dramatically enhanced. Both trailing edge
devices (such as flaps) and leading edge ones (such as slats) are
described. Finally, the most advanced aerodynamic solutions to avoid
the separation of the boundary layer from aircraft wings at high angles
of attack are reviewed.
Abstract: The history of technology and banking is examined as
it relates to risk and technological determinism. It is proposed that
the services that banks offer are determined by technology and that
banks must adopt new technologies to be competitive. The adoption
of technologies paradoxically forces the adoption of other new
technologies to protect the bank from the increased risk of
technology. This cycle will lead to bank examiners and regulators to
focus on human behavior, not on the ever changing technology.
Abstract: Composite pins of rubber dust collected from tyre
retreading centres of trucks, cars and buses etc.and epoxy with
weight percentages of 10. 15, and 20 % of rubber (weight fractions of
9, 13 and 17 % respectively) have been prepared in house with the
help of a split wooden mould. The pins were tested in a pin-on-disc
wear monitor to determine the co-efficient of friction and weight
losses with varying speeds, loads and time. The wear volume and
wear rates have also been found out for all these three specimens.. It
is observed that all the specimens have exhibited very low coefficient
of friction and low wear rates under dry sliding condition. Out of the
above three samples tested, the specimen with 10 % rubber dust by
weight has shown lowest wear rates. However a peculiar result i.e
decreasing trend has been obtained with 20% reinforcement of rubber
in epoxy while rubbed against steel at varying speeds. This might
have occurred due to high surface finish of the disc and formation of
a thin transfer layer from the composite
Abstract: This paper presents a new problem solving approach
that is able to generate optimal policy solution for finite-state
stochastic sequential decision-making problems with high data
efficiency. The proposed algorithm iteratively builds and improves
an approximate Markov Decision Process (MDP) model along with
cost-to-go value approximates by generating finite length trajectories
through the state-space. The approach creates a synergy between an
approximate evolving model and approximate cost-to-go values to
produce a sequence of improving policies finally converging to the
optimal policy through an intelligent and structured search of the
policy space. The approach modifies the policy update step of the
policy iteration so as to result in a speedy and stable convergence to
the optimal policy. We apply the algorithm to a non-holonomic
mobile robot control problem and compare its performance with
other Reinforcement Learning (RL) approaches, e.g., a) Q-learning,
b) Watkins Q(λ), c) SARSA(λ).
Abstract: An attempt has been made to investigate the
machinability of zirconia toughened alumina (ZTA) inserts while
turning AISI 4340 steel. The insert was prepared by powder
metallurgy process route and the machining experiments were
performed based on Response Surface Methodology (RSM) design
called Central Composite Design (CCD). The mathematical model of
flank wear, cutting force and surface roughness have been developed
using second order regression analysis. The adequacy of model has
been carried out based on Analysis of variance (ANOVA) techniques.
It can be concluded that cutting speed and feed rate are the two most
influential factor for flank wear and cutting force prediction. For
surface roughness determination, the cutting speed & depth of cut
both have significant contribution. Key parameters effect on each
response has also been presented in graphical contours for choosing
the operating parameter preciously. 83% desirability level has been
achieved using this optimized condition.
Abstract: Mixed convection in two-dimensional shallow rectangular enclosure is considered. The top hot wall moves with constant velocity while the cold bottom wall has no motion. Simulations are performed for Richardson number ranging from Ri = 0.001 to 100 and for Reynolds number keeping fixed at Re = 408.21. Under these conditions cavity encompasses three regimes: dominating forced, mixed and free convection flow. The Prandtl number is set to 6 and the effects of cavity inclination on the flow and heat transfer are studied for different Richardson number. With increasing the inclination angle, interesting behavior of the flow and thermal fields are observed. The streamlines and isotherm plots and the variation of the Nusselt numbers on the hot wall are presented. The average Nusselt number is found to increase with cavity inclination for Ri ³ 1 . Also it is shown that the average Nusselt number changes mildly with the cavity inclination in the dominant forced convection regime but it increases considerably in the regime with dominant natural convection.
Abstract: This paper deals with the design of a periodic output
feedback controller for a flexible beam structure modeled with
Timoshenko beam theory, Finite Element Method, State space
methods and embedded piezoelectrics concept. The first 3 modes are
considered in modeling the beam. The main objective of this work is
to control the vibrations of the beam when subjected to an external
force. Shear piezoelectric sensors and actuators are embedded into
the top and bottom layers of a flexible aluminum beam structure, thus
making it intelligent and self-adaptive. The composite beam is
divided into 5 finite elements and the control actuator is placed at
finite element position 1, whereas the sensor is varied from position 2
to 5, i.e., from the nearby fixed end to the free end. 4 state space
SISO models are thus developed. Periodic Output Feedback (POF)
Controllers are designed for the 4 SISO models of the same plant to
control the flexural vibrations. The effect of placing the sensor at
different locations on the beam is observed and the performance of
the controller is evaluated for vibration control. Conclusions are
finally drawn.
Abstract: The LHP is a two-phase device with extremely high
effective thermal conductivity that utilizes the thermodynamic
pressure difference to circulate a cooling fluid. A thermodynamics
analytical model is developed to explore different parameters effects
on a Loop Heat Pipe (LHP).. The effects of pipe length, pipe
diameter, condenser temperature, and heat load are reported. As pipe
length increases and/or pipe diameter decreases, a higher temperature
is expected in the evaporator.
Abstract: Use of a sliding joint is an effective method to
decrease the stress in foundation structure where there is a horizontal
deformation of subsoil (areas afflicted with underground mining) or
horizontal deformation of a foundation structure (pre-stressed
foundations, creep, shrinkage, temperature deformation). A
convenient material for a sliding joint is a bitumen asphalt belt.
Experiments for different types of bitumen belts were undertaken at
the Faculty of Civil Engineering - VSB Technical University of
Ostrava in 2008. This year an extension of the 2008 experiments is in
progress and the shear resistance of a slide joint is being tested as a
function of temperature in a temperature controlled room. In this
paper experimental results of temperature dependant shear resistance
are presented. The result of the experiments should be the sliding
joint shear resistance as a function of deformation velocity and
temperature. This relationship is used for numerical analysis of
stress/strain relation between foundation structure and subsoil. Using
a rheological slide joint could lead to a decrease of the reinforcement
amount, and contribute to higher reliability of foundation structure
and thus enable design of more durable and sustainable building
structures.
Abstract: In this paper a simple terrain evaluation method for
hexapod robot is introduced. This method is based on feet coordinate
evaluation when all are on the ground. Depending on the feet
coordinate differences the local terrain evaluation is possible. Terrain
evaluation is necessary for right gait selection and/or body position
correction. For terrain roughness evaluation three planes are plotted:
two of them as definition points use opposite feet coordinates, third
coincides with the robot body plane. The leaning angle of body plane
is evaluated measuring gravity force using three-axis accelerometer.
Terrain roughness evaluation method is based on angle estimation
between normal vectors of these planes. Aim of this work is to
present a simple method for embedded robot controller, allowing to
find the best further movement settings.
Abstract: The presence of chemical bonding between functionalized carbon nanotubes and matrix in carbon nanotube reinforced composites is modeled by elastic beam elements representing covalent bonding characteristics. Neglecting other reinforcing mechanisms in the composite such as relatively weak interatomic Van der Waals forces, this model shows close results to the Rule of Mixtures model-s prediction for effective Young-s modulus of a Representative Volume Element of composite for small volume fractions (~1%) and high aspect ratios (L/D>200) of CNTs.
Abstract: Anti-money laundering is commonly recognized as a
set of procedures, laws or regulations designed to reduce the practice
of generating income through illegal actions. In Malaysia, the
government and law enforcement agencies have stepped up their
capacities and efforts to curb money laundering since 2001. One of
these measures was the enactment of the Anti-Money Laundering
Act (AMLA) in 2001. The implementation costs on anti-money
laundering requirements (AMLR) can be burdensome to those who
are involved in enforcing them. The objective of this paper is to
explore the perceived effectiveness of AMLR from the enforcement
agencies- perspective. This is a preliminary study whose findings
will help to give direction for further AML research in Malaysia. In
addition, the results of this study provide empirical evidences on the
perceived effectiveness of AMLR prior to further investigations on
barriers and improvements of the implementation of the anti-money
laundering regime in Malaysia.
Abstract: This paper analyzes the effect of a single uniform accounting rule on reporting quality by investigating the influence of IFRS on earnings management. This paper examines whether earnings management is reduced after IFRS adoption through the use of “loss avoidance thresholds”, a method that has been verified in earlier studies. This paper concentrates on two European countries: one that represents the continental code law tradition with weak protection of investors (France) and one that represents the Anglo-American common law tradition, which typically implies a strong enforcement system (the United Kingdom).
The research investigates a sample of 526 companies (6822 firm-year observations) during the years 2000 – 2013. The results are different for the two jurisdictions. This study demonstrates that a single set of accounting standards contributes to better reporting quality and reduces the pervasiveness of earnings management in France. In contrast, there is no evidence that a reduction in earnings management followed the implementation of IFRS in the United Kingdom. Due to the fact that IFRS benefit France but not the United Kingdom, other political and economic factors, such legal system or capital market strength, must play a significant role in influencing the comparability and transparency cross-border companies’ financial statements. Overall, the result suggests that IFRS moderately contribute to the accounting quality of reported financial statements and bring benefit for stakeholders, though the role played by other economic factors cannot be discounted.
Abstract: Service life of existing reinforced concrete (RC)
structures in coastal towns of Sabah has been affected very much.
Concrete crack, spalling of concrete cover and reinforcement rusting
of RC buildings are seen even within 5 years of construction in
Sabah. Hence, in this study a new mix design of concrete grout was
developed using locally available materials and investigated under
two curing conditions and workability, compressive strength,
Accelerated Mortar Bar Test (AMBT), water absorption, volume of
permeable voids (VPV), Sorptivity and 90-days salt ponding test
were conducted. The compressive strength of concrete grout at the
age 90 days was found to be 44.49 N/mm2 under water curing. It was
observed that the percentage of mortar bar length change was below
1% for developed concrete grout. The water absorption of the
concrete grout was in between the range of 0.88 % to 3.60 % under
two different curing up to the age 90 days. It was also observed that
the VPV of concrete was in the range of 0 % to 9.75 and 2.44% to
13.05% under water curing and site curing respectively. It was found
that the Sorptivity of the concrete grout under water curing at the age
of 28 days is 0.211mm/√min and at the age 90 day are 0.067
mm/√min. The chloride content decreased greatly, 90% after a depth
of 15 mm. It was noticed that the site cured samples showed higher
chloride contents near surface compared to water cured samples.
This investigation suggested that the developed mix design of
concrete grout using locally available construction materials can be
used for crack repairing of existing RC structures in Sabah.
Abstract: The complex shape of the human pelvic bone was
successfully imaged and modeled using finite element FE processing.
The bone was subjected to quasi-static and dynamic loading
conditions simulating the effect of both weight gain and impact.
Loads varying between 500 – 2500 N (~50 – 250 Kg of weight) was
used to simulate 3D quasi-static weight gain. Two different 3D
dynamic analyses, body free fall at two different heights (1 and 2 m)
and forced side impact at two different velocities (20 and 40 Km/hr)
were also studied. The computed resulted stresses were compared for
the four loading cases, where Von Misses stresses increases linearly
with the weight gain increase under quasi-static loading. For the
dynamic models, the Von Misses stress history behaviors were
studied for the affected area and effected load with respect to time.
The normalization Von Misses stresses with respect to the applied
load were used for comparing the free fall and the forced impact load
results. It was found that under the forced impact loading condition
an over lapping behavior was noticed, where as for the free fall the
normalized Von Misses stresses behavior was found to nonlinearly
different. This phenomenon was explained through the energy
dissipation concept. This study will help designers in different
specialization in defining the weakest spots for designing different
supporting systems.
Abstract: Nayak et al have discussed in detail the inertial forces
such as Gravitational, Coriolis-Lense-Thirring and Centrifugal forces
in the Kerr-Newman Space-time in the Kerr-Newman Space-time.
The main theme of this paper is to study the Gravitational and
Centrifugal forces in the NUT-Kerr-Newman Space-time.
Abstract: This paper summaries basic principles and concepts of
intelligent controls, implemented in humanoid robotics as well as
recent algorithms being devised for advanced control of humanoid
robots. Secondly, this paper presents a new approach neuro-fuzzy
system. We have included some simulating results from our
computational intelligence technique that will be applied to our
humanoid robot. Subsequently, we determine a relationship between
joint trajectories and located forces on robot-s foot through a
proposed neuro-fuzzy technique.
Abstract: Literature review revealed the importance of the
adoption of marketing Relationship for loyalty and retaining
profitable customer (Customer Relationship Management). LPQ
satisfaction will reinforce the loyalty and customer brand
attachment. Customer will communicate the operator to others. The
focus of this study is to examine the relationship between the
LPPQ and the WOM recommendations through: customer
satisfaction, loyalty and attachment. The results show that LPQ
affect positively the satisfaction, negatively the loyalty. LPQ has an
indirectly effect on WOM recommendations but through the
satisfaction and attachment. The mediating effect of satisfaction in
the relationship between LPQ and Loyalty is rejected. This finding
can be explained by the nature of mobile sector in Tunisia.
Abstract: In This paper, the behavior of eccentric braced frame
(EBF) is studied with replacing friction damper (FD) in confluence of these braces, in 5 and 10-storey steel frames. For FD system, the main step is to determine the slip load. For this reason, the performance indexes include roof displacement, base shear, dissipated energy and relative performance should be investigated. In
nonlinear dynamic analysis, the response of structure to three
earthquake records has been obtained and the values of roof
displacement, base shear and column axial force for FD and EBF
frames have been compared. The results demonstrate that use of the FD in frames, in comparison with the EBF, substantially reduces the roof displacement, column axial force and base shear. The obtained results show suitable performance of FD in higher storey structure in
comparison with the EBF.
Abstract: Unmanned aerial vehicles (UAVs) performing their
operations for a long time have been attracting much attention in
military and civil aviation industries for the past decade. The
applicable field of UAV is changing from the military purpose only to
the civil one. Because of their low operation cost, high reliability and
the necessity of various application areas, numerous development
programs have been initiated around the world. To obtain the optimal
solutions of the design variable (i.e., sectional airfoil profile, wing
taper ratio and sweep) for high performance of UAVs, both the lift and
lift-to-drag ratio are maximized whereas the pitching moment should
be minimized, simultaneously. It is found that the lift force and
lift-to-drag ratio are linearly dependent and a unique and dominant
solution are existed. However, a trade-off phenomenon is observed
between the lift-to-drag ratio and pitching moment. As the result of
optimization, sixty-five (65) non-dominated Pareto individuals at the
cutting edge of design spaces that are decided by airfoil shapes can be
obtained.