Abstract: Higher capacities of power plants together with
increased awareness on environmental considerations have led to
taller height of stacks. It is seen that strong wind can result in falling
of stacks. So, aerodynamic consideration of stacks is very important
in order to save the falling of stacks. One stack is not enough in
industries and power sectors and two or three stacks are required for
proper operation of the unit. It is very important to arrange the stacks
in proper way to resist their downfall. The present experimental
study concentrates on the mutual effect of three nearby stacks on
each other at three different arrangements, viz. linear, side-by-side
and triangular. The experiments find out the directions of resultant
forces acting on the stacks in different configurations so that proper
arrangement of supports can be made with respect to the wind
directionality obtained from local meteorological data. One can also
easily ascertain which stack is more vulnerable to wind in
comparison to the others for a particular configuration. Thus, this
study is important in studying the effect of wind force on three stacks
in different arrangements and is very helpful in placing the supports
in proper places in order to avoid failing of stack-like structures due
to wind.
Abstract: A nonlinear model of two-beam free-electron laser
(FEL) in the absence of slippage is presented. The two beams are
assumed to be cold with different energies and the fundamental
resonance of the higher energy beam is at the third harmonic of lower
energy beam. By using Maxwell-s equations and full Lorentz force
equations of motion for the electron beams, coupled differential
equations are derived and solved numerically by the fourth order
Runge–Kutta method. In this method a considerable growth of third
harmonic electromagnetic field in the XUV and X-ray regions is
predicted.
Abstract: The paper describes ergonomics problems trend of
student at B5101 classroom building 2, Suranaree University of
Technology. The objective to survey ergonomics problems and effect
from use chairs for sitting in class room. The result from survey
method 100 student they use lecture chair for sitting in classroom
more than 2 hours/ day by RULA[1]. and Body discomfort survey[2].
The result from Body discomfort survey contribute fatigue problems
at neck, lower back, upper back and right shoulder 2.93, 2.91, 2.33,
1.75 respectively and result from RULA contribute fatigue problems
at neck, body and right upper arm 4.00, 3.75 and 3.00 respectively
are consistent. After that the researcher provide improvement plan
for design new chair support student fatigue reduction by prepare
data of sample anthropometry and design ergonomics chair prototype
3 unit. Then sample 100 student trial to use new chair and evaluate
again by RULA, Body discomfort and satisfaction. The result from
trial new chair after improvement by RULA present fatigue reduction
average of head and neck from 4.00 to 2.25 , body and trunk from
3.75 to 2.00 and arm force from 1.00 to 0.25 respectively. The result
from trial new chair after improvement by Body discomfort present
fatigue reduction average of lower back from 2.91 to 0.87, neck from
2.93 to 1.24, upper back 2.33 to 0.84 and right upper arm from 1.75
to 0.74. That statistical of RULA and Body discomfort survey
present fatigue reduction after improvement significance with a
confidence level of 95% (p-value 0.05). When analyzing the
relationship of fatigue as part of the body by Chi – square test during
RULA and Body discomfort that before and after improvements were
consistent with the significant level of confidence 95% (p-value 0.05)
. Moreover the students satisfaction result from trial with a new chair
for 30 minutes [3]. 72 percent very satisfied of the folding of the
secondary writing simple 66% the width of the writing plate, 64% the
suitability of the writing plate, 62% of soft seat cushion and 61%
easy to seat the chair.
Abstract: The unique structural configuration found in human foot allows easy walking. Similar movement is hard to imitate even for an ape. It is obvious that human ambulation relates to the foot structure itself. Suppose the bones are represented as vertices and the joints as edges. This leads to the development of a special graph that represents human foot. On a footprint there are point-ofcontacts which have contact with the ground. It involves specific vertices. Theoretically, for an ideal ambulation, these points provide reactions onto the ground or the static equilibrium forces. They are arranged in sequence in form of a path. The ambulating footprint follows this path. Having the human foot graph and the path crossbred, it results in a representation that describes the profile of an ideal ambulation. This profile cites the locations where the point-of-contact experience normal reaction forces. It highlights the significant of these points.
Abstract: In this paper, free vibration analysis of carbon nanotube (CNT) reinforced laminated composite panels is presented. Three types of panels such as flat, concave and convex are considered for study. Numerical simulation is carried out using commercially available finite element analysis software ANSYS. Numerical homogenization is employed to calculate the effective elastic properties of randomly distributed carbon nanotube reinforced composites. To verify the accuracy of the finite element method, comparisons are made with existing results available in the literature for conventional laminated composite panels and good agreements are obtained. The results of the CNT reinforced composite materials are compared with conventional composite materials under different boundary conditions.
Abstract: In this paper, a worm-like micro robot designed for inpipe
application with intelligent active force control (AFC) capability
is modelled and simulated. The motion of the micro robot is based on
an impact drive mechanism (IDM) that is actuated using piezoelectric
device. The trajectory tracking performance of the modelled micro
robot is initially experimented via a conventional proportionalintegral-
derivative (PID) controller in which the dynamic response of
the robot system subjected to different input excitations is
investigated. Subsequently, a robust intelligent method known as
active force control with fuzzy logic (AFCFL) is later incorporated
into the PID scheme to enhance the system performance by
compensating the unwanted disturbances due to the interaction of the
robot with its environment. Results show that the proposed AFCFL
scheme is far superior than the PID control counterpart in terms of
the system-s tracking capability in the wake of the disturbances.
Abstract: Electro-hydraulic power steering (EHPS) system for
the fuel rate reduction and steering feel improvement is comprised of
ECU including the logic which controls the steering system and BL
DC motor and produces the best suited cornering force, BLDC motor,
high pressure pump integrated module and basic oil-hydraulic circuit
of the commercial HPS system.
Electro-hydraulic system can be studied in two ways such as
experimental and computer simulation. To get accurate results in
experimental study of EHPS system, the real boundary management is
necessary which is difficult task. And the accuracy of the experimental
results depends on the preparation of the experimental setup and
accuracy of the data collection. The computer simulation gives
accurate and reliable results if the simulation is carried out considering
proper boundary conditions. So, in this paper, each component of
EHPS was modeled, and the model-based analysis and control logic
was designed by using AMESim
Abstract: The dynamics of the Autonomous Underwater
Vehicles (AUVs) are highly nonlinear and time varying and the hydrodynamic coefficients of vehicles are difficult to estimate
accurately because of the variations of these coefficients with
different navigation conditions and external disturbances. This study presents the on-line system identification of AUV dynamics to obtain
the coupled nonlinear dynamic model of AUV as a black box. This black box has an input-output relationship based upon on-line
adaptive fuzzy model and adaptive neural fuzzy network (ANFN)
model techniques to overcome the uncertain external disturbance and
the difficulties of modelling the hydrodynamic forces of the AUVs instead of using the mathematical model with hydrodynamic parameters estimation. The models- parameters are adapted according
to the back propagation algorithm based upon the error between the
identified model and the actual output of the plant. The proposed
ANFN model adopts a functional link neural network (FLNN) as the
consequent part of the fuzzy rules. Thus, the consequent part of the
ANFN model is a nonlinear combination of input variables. Fuzzy
control system is applied to guide and control the AUV using both
adaptive models and mathematical model. Simulation results show
the superiority of the proposed adaptive neural fuzzy network
(ANFN) model in tracking of the behavior of the AUV accurately
even in the presence of noise and disturbance.
Abstract: This work deals with problems of tool axis inclination angles in ball-end milling. Tool axis inclination angle contributes to improvement of functional surface properties (surface integrity - surface roughness, residual stress, micro hardness, etc.), decreasing cutting forces and improving production. By milling with ball-end milling tool, using standard way of cutting, when work piece and cutting tool contain right angle, we have zero cutting speed on edge. At this point cutting tool only pushes material into the work piece. Here we can observe the following undesirable effects - chip contraction, increasing of cutting temperature, increasing vibrations or creation of built-up edge. These effects have negative results – low quality of surface and decreasing of tool life (in the worse case even it is pinching out). These effects can be eliminated with the tilt of cutting tool or tilt of work piece.
Abstract: Crawling movement as a motive mode seen in nature
of some animals such as snakes possesses a specific syntactic and
dynamic analysis. Serpentine robot designed by inspiration from
nature and snake-s crawling motion, is regarded as a crawling robot.
In this paper, a serpentine robot with spiral motion model will be
analyzed. The purpose of this analysis is to calculate the vertical and
tangential forces along snake-s body and to determine the parameters
affecting on these forces. Two types of serpentine robots have been
designed in order to examine the achieved relations explained below.
Abstract: An experimental study of Reinforced Concrete, RC, columns strengthened using a steel jacketing technique was conducted. The jacketing technique consisted of four steel vertical angles installed at the corners of the column joined by horizontal steel straps confining the column externally. The effectiveness of the technique was evaluated by testing the RC column specimens under eccentric monotonic loading until failure occurred. Strain gauges were installed to monitor the strains in the internal reinforcement as well as the external jacketing system. The effectiveness of the jacketing technique was demonstrated, and the parameters affecting the technique were studied.
Abstract: The effect of different combinations of response
feedback on the performance of active control system on nonlinear
frames has been studied in this paper. To this end different feedback
combinations including displacement, velocity, acceleration and full
response feedback have been utilized in controlling the response of
an eight story bilinear hysteretic frame which has been subjected to a
white noise excitation and controlled by eight actuators which could
fully control the frame. For active control of nonlinear frame
Newmark nonlinear instantaneous optimal control algorithm has been
used which a diagonal matrix has been selected for weighting
matrices in performance index. For optimal design of active control
system while the objective has been to reduce the maximum drift to
below the yielding level, Distributed Genetic Algorithm (DGA) has
been used to determine the proper set of weighting matrices. The
criteria to assess the effect of each combination of response feedback
have been the minimum required control force to reduce the
maximum drift to below the yielding drift. The results of numerical
simulation show that the performance of active control system is
dependent on the type of response feedback where the velocity
feedback is more effective in designing optimal control system in
comparison with displacement and acceleration feedback. Also using
full feedback of response in controller design leads to minimum
control force amongst other combinations. Also the distributed
genetic algorithm shows acceptable convergence speed in solving the
optimization problem of designing active control systems.
Abstract: Encryption protects communication partners from
disclosure of their secret messages but cannot prevent traffic analysis
and the leakage of information about “who communicates with
whom". In the presence of collaborating adversaries, this linkability
of actions can danger anonymity. However, reliably providing
anonymity is crucial in many applications. Especially in contextaware
mobile business, where mobile users equipped with PDAs
request and receive services from service providers, providing
anonymous communication is mission-critical and challenging at the
same time. Firstly, the limited performance of mobile devices does
not allow for heavy use of expensive public-key operations which are
commonly used in anonymity protocols. Moreover, the demands for
security depend on the application (e.g., mobile dating vs. pizza
delivery service), but different users (e.g., a celebrity vs. a normal
person) may even require different security levels for the same
application. Considering both hardware limitations of mobile devices
and different sensitivity of users, we propose an anonymity
framework that is dynamically configurable according to user and
application preferences. Our framework is based on Chaum-s mixnet.
We explain the proposed framework, its configuration
parameters for the dynamic behavior and the algorithm to enforce
dynamic anonymity.
Abstract: The indoor airflow with a mixed natural/forced convection
was numerically calculated using the laminar and turbulent
approach. The Boussinesq approximation was considered for a simplification
of the mathematical model and calculations. The results
obtained, such as mean velocity fields, were successfully compared
with experimental PIV flow visualizations. The effect of the distance
between the cooled wall and the heat exchanger on the temperature
and velocity distributions was calculated. In a room with a simple
shape, the computational code OpenFOAM demonstrated an ability to
numerically predict flow patterns. Furthermore, numerical techniques,
boundary type conditions and the computational grid quality were
examined. Calculations using the turbulence model k-omega had a
significant effect on the results influencing temperature and velocity
distributions.
Abstract: To investigate the behavior of sheet metals during
forming tailor welded blanks (TWB) of various thickness made via
Co2 Laser welding are under consideration. These blanks are formed
used two different forming methods of rubber as well as the
conventional punch and die methods. The main research objective is
the effects of using a rubber die instead of a solid one the
displacement of the weld line and the press force needed for forming.
Specimens with thicknesses of 0.5, 0.6, 0.8 and 1mm are subjected to
Erichsen two dimensional tests and the resulted force for each case
are compared. This is followed by a theoretical and numerical study
of press force and weld line displacement. It is concluded that using
rubber pad forming (RPF) causes a reduction in weld line
displacement and an increase in the press force.
Abstract: Today air-core coils (ACC) are a viable alternative to
ferrite-core coils in a range of applications due to their low induction
effect. An analytical study was carried out and the results were used as
a guide to understand the relationship between the magnet-coil
distance and the resulting attractive magnetic force. Four different
ACC models were fabricated for experimental study. The variation in
the models included the dimensions, the number of coil turns and the
current supply to the coil. Comparison between the analytical and
experimental results for all the models shows an average discrepancy
of less than 10%. An optimized ACC design was selected for the
scanner which can provide maximum magnetic force.
Abstract: When a high DC voltage is applied to a capacitor with
strongly asymmetrical electrodes, it generates a mechanical force that
affects the whole capacitor. This phenomenon is most likely to be
caused by the motion of ions generated around the smaller of the two
electrodes and their subsequent interaction with the surrounding
medium. A method to measure this force has been devised and used.
A formula describing the force has also been derived. After
comparing the data gained through experiments with those acquired
using the theoretical formula, a difference was found above a certain
value of current. This paper also gives reasons for this difference.
Abstract: Interior brick-infill partitions are usually considered as
non-structural components, and only their weight is accounted for in
practical structural design. In this study, the brick-infill panels are
simulated by compression struts to clarify their effect on the
progressive collapse potential of an earthquake-resistant RC building.
Three-dimensional finite element models are constructed for the RC
building subjected to sudden column loss. Linear static analyses are
conducted to investigate the variation of demand-to-capacity ratio
(DCR) of beam-end moment and the axial force variation of the beams
adjacent to the removed column. Study results indicate that the
brick-infill effect depends on their location with respect to the
removed column. As they are filled in a structural bay with a shorter
span adjacent to the column-removed line, more significant reduction
of DCR may be achieved. However, under certain conditions, the
brick infill may increase the axial tension of the two-span beam
bridging the removed column.
Abstract: The ever increasing product diversity and competition on the market of goods and services has dictated the pace of growth in the number of advertisements. Despite their admittedly diminished effectiveness over the recent years, advertisements remain the favored method of sales promotion. Consequently, the challenge for an advertiser is to explore every possible avenue of making an advertisement more noticeable, attractive and impellent for consumers. One way to achieve this is through invoking celebrity endorsements. On the one hand, the use of a celebrity to endorse a product involves substantial costs, however, on the other hand, it does not immediately guarantee the success of an advertisement. The question of how celebrities can be used in advertising to the best advantage is therefore of utmost importance. Celebrity endorsements have become commonplace: empirical evidence indicates that approximately 20 to 25 per cent of advertisements feature some famous person as a product endorser. The popularity of celebrity endorsements demonstrates the relevance of the topic, especially in the context of the current global economic downturn, when companies are forced to save in order to survive, yet simultaneously to heavily invest in advertising and sales promotion. The issue of the effective use of celebrity endorsements also figures prominently in the academic discourse. The study presented below is thus aimed at exploring what qualities (characteristics) of a celebrity endorser have an impact on the ffectiveness of the advertisement in which he/she appears and how.
Abstract: Conventional concentrically-braced frame (CBF)
systems have limited drift capacity before brace buckling and related
damage leads to deterioration in strength and stiffness. Self-centering
concentrically-braced frame (SC-CBF) systems have been developed
to increase drift capacity prior to initiation of damage and minimize
residual drift. SC-CBFs differ from conventional CBFs in that the
SC-CBF columns are designed to uplift from the foundation at a
specified level of lateral loading, initiating a rigid-body rotation
(rocking) of the frame. Vertically-aligned post-tensioning bars resist
uplift and provide a restoring force to return the SC-CBF columns to
the foundation (self-centering the system). This paper presents a
parametric study of different prototype buildings using SC-CBFs.
The bay widths of the SC-CBFs have been varied in these buildings
to study different geometries. Nonlinear numerical analyses of the
different SC-CBFs are presented to illustrate the effect of frame
geometry on the behavior and dynamic response of the SC-CBF
system.