Abstract: To determine the potential of a low cost Irish
engineered timber product to replace high cost solid timber for use in
bending active structures such as gridshells a single Irish engineered
timber product in the form of orientated strand board (OSB) was
selected. A comparative study of OSB and solid timber was carried
out to determine the optimum properties that make a material suitable
for use in gridshells. Three parameters were identified to be relevant
in the selection of a material for gridshells. These three parameters
are the strength to stiffness ratio, the flexural stiffness of
commercially available sections, and the variability of material and
section properties. It is shown that when comparing OSB against
solid timber, OSB is a more suitable material for use in gridshells that
are at the smaller end of the scale and that have tight radii of
curvature. Typically, for solid timber materials, stiffness is used as an
indicator for strength and engineered timber is no different. Thus, low
flexural stiffness would mean low flexural strength. However, when
it comes to bending active gridshells, OSB offers a significant
advantage. By the addition of multiple layers, an increased section
size is created, thus endowing the structure with higher stiffness and
higher strength from initial low stiffness and low strength materials
while still maintaining tight radii of curvature. This allows OSB to
compete with solid timber on large scale gridshells. Additionally, a
preliminary sustainability study using a set of sustainability indicators
was carried out to determine the relative sustainability of building a
large-scale gridshell in Ireland with a primary focus on economic
viability but a mention is also given to social and environmental
aspects. For this, the Savill garden gridshell in the UK was used as
the functional unit with the sustainability of the structural roof
skeleton constructed from UK larch solid timber being compared
with the same structure using Irish OSB. Albeit that the advantages of
using commercially available OSB in a bending active gridshell are
marginal and limited to specific gridshell applications, further study
into an optimised engineered timber product is merited.
Abstract: Most people today are aware that global climate
change is not just a scientific theory but also a fact with worldwide
consequences. Global climate change is due to rapid urbanization,
industrialization, high population growth and current vulnerability of
the climatic condition. Water is becoming scarce as a result of global
climate change. To mitigate the problem arising due to global climate
change and its drought effect, harvesting rainwater from green roofs,
an environmentally-friendly and versatile technology, is becoming
one of the best assessment criteria and gaining attention in Malaysia.
This paper addresses the sustainability of green roofs and examines
the quality of water harvested from green roofs in comparison to
rainwater. The factors that affect the quality of such water, taking
into account, for example, roofing materials, climatic conditions, the
frequency of rainfall frequency and the first flush. A green roof was
installed on the Humid Tropic Centre (HTC) is a place of the study
on monitoring program for urban Stormwater Management Manual
for Malaysia (MSMA), Eco-Hydrological Project in Kuala Lumpur,
and the rainwater was harvested and evaluated on the basis of four
parameters i.e., conductivity, dissolved oxygen (DO), pH and
temperature. These parameters were found to fall between Class I and
Class III of the Interim National Water Quality Standards (INWQS)
and the Water Quality Index (WQI). Some preliminary treatment
such as disinfection and filtration could likely to improve the value of
these parameters to class I. This review paper clearly indicates that
there is a need for more research to address other microbiological and
chemical quality parameters to ensure that the harvested water is
suitable for use potable water for domestic purposes. The change in
all physical, chemical and microbiological parameters with respect to
storage time will be a major focus of future studies in this field.
Abstract: The Markov decision process (MDP) based
methodology is implemented in order to establish the optimal
schedule which minimizes the cost. Formulation of MDP problem
is presented using the information about the current state of pipe,
improvement cost, failure cost and pipe deterioration model. The
objective function and detailed algorithm of dynamic programming
(DP) are modified due to the difficulty of implementing the
conventional DP approaches. The optimal schedule derived from
suggested model is compared to several policies via Monte
Carlo simulation. Validity of the solution and improvement in
computational time are proved.
Abstract: Background: The objectives of this study were to
assess patient’s knowledge of appropriate sublingual glyceryl
trinitrate (GTN) use as well as to investigate how patients commonly
store and carry their sublingual GTN tablets. Methodology: This was
a cross-sectional survey, using a validated researcher-administered
questionnaire. The study involved cardiac patients receiving
sublingual GTN attending the outpatient and inpatient departments of
Taiping Hospital, a non-academic public care hospital. The minimum
calculated sample size was 92, but 100 patients were conveniently
sampled. Respondents were interviewed on 3 areas, including
demographic data, knowledge and use of sublingual GTN. Eight
items were used to calculate each subject’s knowledge score and six
items were used to calculate use score. Results: Of the 96 patients
who consented to participate, majority (96.9%) were well aware of
the indication of sublingual GTN. With regards to the mechanism of
action of sublingual GTN, 73 (76%) patients did not know how the
medication works. Majority of the patients (66.7%) knew about the
proper storage of the tablet. In relation to the maximum number of
sublingual GTN tablets that can be taken during each angina episode,
36.5% did not know that up to 3 tablets of sublingual GTN can be
taken during each episode of angina. Fifty four (56.2%) patients were
not aware that they need to replace sublingual GTN every 8 weeks
after receiving the tablets. Majority (69.8%) of the patients
demonstrated lack of knowledge with regards to the use of sublingual
GTN as prevention of chest pain. Conclusion: Overall, patients’
knowledge regarding the self-administration of sublingual GTN is
still inadequate. The findings support the need for more frequent
reinforcement of patient education, especially in the areas of
preventive use, storage and drug stability.
Abstract: This research has been conducted to study the method
of culture and comparing growth and biomass of Gracilaria corticata
cultured on rope and net for 50 days through two treatments (first
treatment: culture of alga on net and the second treatment: culture of
alga on rope and each treatment was repeated by four cases). During
culture period, the water of aquariums was replaced once every two
days for 40-50%. Also, 0.3-0.5 grams of urea fertilizer was added to
the culture environment for fertilization. Moreover, some of the
environmental factors such as pH, salinity and temperature of the
environment were measured on a daily basis. During the culture
period, extent of longitudinal growth of the species of both treatments
was equal. The said length was reached from 8-10 cm to 10.5-13 cm
accordingly. The resulted weight in repetitions of the first treatment
was higher than that of the second treatment in such a way as in the
first treatment, its weight reached from 10 grams to 21.119 grams and
in the second treatment, its weight reached from 10 grams to 17.663
grams. On a whole, it may be stated that that kind of alga being
studied has a considerable growth with respect to its volume. The
results have revealed that the percentage of daily growth and wet
weight at the end of the first treatment was higher than that of the
second treatment and it was registered as 0.934, 6.072 and 811.432 in
the first treatment and 0.797, 4.990 and 758.071 in the second
treatment respectively. This difference is significant (P
Abstract: Over the past four decades, the fatigue behavior of
nickel-based alloys has been widely studied. However, in recent
years, significant advances in the fabrication process leading to grain
size reduction have been made in order to improve fatigue properties
of aircraft turbine discs. Indeed, a change in particle size affects the
initiation mode of fatigue cracks as well as the fatigue life of the
material. The present study aims to investigate the fatigue behavior of
a newly developed nickel-based superalloy under biaxial-planar
loading. Low Cycle Fatigue (LCF) tests are performed at different
stress ratios so as to study the influence of the multiaxial stress state
on the fatigue life of the material. Full-field displacement and strain
measurements as well as crack initiation detection are obtained using
Digital Image Correlation (DIC) techniques. The aim of this
presentation is first to provide an in-depth description of both the
experimental set-up and protocol: the multiaxial testing machine, the
specific design of the cruciform specimen and performances of the
DIC code are introduced. Second, results for sixteen specimens
related to different load ratios are presented. Crack detection, strain
amplitude and number of cycles to crack initiation vs. triaxial stress
ratio for each loading case are given. Third, from fractographic
investigations by scanning electron microscopy it is found that the
mechanism of fatigue crack initiation does not depend on the triaxial
stress ratio and that most fatigue cracks initiate from subsurface
carbides.
Abstract: Power systems are operating under stressed condition
due to continuous increase in demand of load. This can lead to
voltage instability problem when face additional load increase or
contingency. In order to avoid voltage instability suitable size of
reactive power compensation at optimal location in the system is
required which improves the load margin. This work aims at
obtaining optimal size as well as location of compensation in the 39-
bus New England system with the help of Bacteria Foraging and
Genetic algorithms. To reduce the computational time the work
identifies weak candidate buses in the system, and then picks only
two of them to take part in the optimization. The objective function is
based on a recently proposed voltage stability index which takes into
account the weighted average sensitivity index is a simpler and faster
approach than the conventional CPF algorithm. BFOA has been
found to give better results compared to GA.
Abstract: Over the past few years, the online multimedia
collection has grown at a fast pace. Several companies showed
interest to study the different ways to organise the amount of audio
information without the need of human intervention to generate
metadata. In the past few years, many applications have emerged on
the market which are capable of identifying a piece of music in a
short time. Different audio effects and degradation make it much
harder to identify the unknown piece. In this paper, an audio
fingerprinting system which makes use of a non-parametric based
algorithm is presented. Parametric analysis is also performed using
Gaussian Mixture Models (GMMs). The feature extraction methods
employed are the Mel Spectrum Coefficients and the MPEG-7 basic
descriptors. Bin numbers replaced the extracted feature coefficients
during the non-parametric modelling. The results show that nonparametric
analysis offer potential results as the ones mentioned in
the literature.
Abstract: This study estimates the seismic demands of tall
buildings with central symmetric setbacks by using nonlinear time
history analysis. Three setback structures, all 60-story high with
setback in three levels, are used for evaluation. The effects of
irregularities occurred by setback are evaluated by determination of
global-drift, story-displacement and story drift. Story-displacement is
modified by roof displacement and first story displacement and story
drift is modified by global drift. All results are calculated at the
center of mass and in x and y direction. Also the absolute values of
these quantities are determined. The results show that increasing of
vertical irregularities increases the global drift of the structure and
enlarges the deformations in the height of the structure. It is also
observed that the effects of geometry irregularity in the seismic
deformations of setback structures are higher than those of mass
irregularity.
Abstract: Flow blockages referring to the increase in flow are
being considered as a vital equipment for marine current energy
conversion. However, the shape of these devices will result in
extracted energy under the operation. The present work investigates
the effect of two configurations of a grating, convergent and
divergent that located upstream, to the water flow velocity. The flow
characteristics are studied by Computational Fluid Dynamic
simulation by using the ANSYS Fluent solver for these specified
arrangements of the grating. The results indicate that distinguished
characteristics of flow velocity between “convergent” and
“divergent” grating placements is up to 10% in confined conditions.
Furthermore, the velocity in case of convergent grating is higher
than that of divergent grating.
Abstract: This paper presents Finite Element Method (FEM) for
analyzing the internal responses generated in thin rectangular plates
with various edge conditions and rigidity conditions. Comparison has
been made between the FEM (ANSYS software) results for
displacement, stresses and moments generated with and without the
consideration of hole in plate and different aspect ratios. In the end
comparison for responses in plain and composite square plates has
been studied.
Abstract: In this paper, the author studied the possibilities of
using Rice Husk Ash (RHA) available in India; to produce concrete.
Experiments conducted with RHA obtained from West Bengal, India;
to replace cement partially to produce concrete of grade M10, M15,
M20, M25 and M30. The concrete produced in the laboratory by
replacing cement by 5%, 10%, 15%, 20%, 25% and 30% RHA.
Compressive strength tests carried out to determine the strength of
concrete. Cost analysis and comparison done to show the cost
effectiveness of RHA Concrete. Traditional uses of Rice Husk in
India pointed out and the advantages of using RHA in making
concrete highlighted. Suggestion provided regarding prospective
application of RHA concrete in India; which in turn will definitely
reduce the cost of concrete and environmental friendly due to
utilization of waste and replacement of Cement.
Abstract: In this study, the root of the name Lykaonia and the geographical area defined as Lykaonia Region are mentioned. In this context, information concerning the settlements of Paleolithic Age, Neolithic Age and Chalcolithic Age are given place. Particularly the settlements belonging to Classical Age are localized and brief information about the history of these settlements is provided. In the light of this information, roads of Antique period in the region are evaluated.
Abstract: Starting from nonlocal continuum mechanics, a
thermodynamically new nonlocal model of Euler-Bernoulli
nanobeams is provided. The nonlocal variational formulation is
consistently provided and the governing differential equation for
transverse displacement is presented. Higher-order boundary
conditions are then consistently derived. An example is contributed in
order to show the effectiveness of the proposed model.
Abstract: The seismic responses of steel buildings with semirigid
post-tensioned connections (PC) are estimated and compared
with those of steel buildings with typical rigid (welded) connections
(RC). The comparison is made in terms of global and local response
parameters. The results indicate that the seismic responses in terms of
interstory shears, roof displacements, axial load and bending
moments are smaller for the buildings with PC connection. The
difference is larger for global than for local parameters, which in turn
varies from one column location to another. The reason for this
improved behavior is that the buildings with PC dissipate more
hysteretic energy than those with RC. In addition, unlike the case of
buildings with WC, for the PC structures the hysteretic energy is
mostly dissipated at the connections, which implies that structural
damage in beams and columns is not significant. According to these
results, steel buildings with PC are a viable option in high seismicity
areas because of their smaller response and self-centering connection
capacity as well as the fact that brittle failure is avoided.
Abstract: This study aims to investigate the possibility of crime
prevention through CCTV by analyzing the appropriateness of the
CCTV location, whether it is installed in the hotspot of crime-prone
areas, and exploring the crime prevention effect and transition effect.
The real crime and CCTV locations of case city were converted into
the spatial data by using GIS. The data was analyzed by hotspot
analysis and weighted displacement quotient (WDQ). As study
methods, it analyzed existing relevant studies for identifying the trends
of CCTV and crime studies based on big data from 1800 to 2014 and
understanding the relation between CCTV and crime. Second, it
investigated the current situation of nationwide CCTVs and analyzed
the guidelines of CCTV installation and operation to draw attention to
the problems and indicating points of CCTV use. Third, it investigated
the crime occurrence in case areas and the current situation of CCTV
installation in the spatial aspects, and analyzed the appropriateness and
effectiveness of CCTV installation to suggest a rational installation of
CCTV and the strategic direction of crime prevention. The results
demonstrate that there was no significant effect in the installation of
CCTV on crime prevention in the case area. This indicates that CCTV
should be installed and managed in a more scientific way reflecting
local crime situations. In terms of CCTV, the methods of spatial
analysis such as GIS, which can evaluate the installation effect, and the
methods of economic analysis like cost-benefit analysis should be
developed. In addition, these methods should be distributed to local
governments across the nation for the appropriate installation of
CCTV and operation. This study intended to find a design guideline of
the optimum CCTV installation. In this regard, this study is
meaningful in that it will contribute to the creation of a safe city.
Abstract: The purpose of this presentation is to describe an interdisciplinary teaching program that integrates physical education concepts using a philosophical approach. The presentation includes a review of: a) the philosophy of American education, b) the philosophy of sports and physical education, c) the interdisciplinary physical education program, d) professional development programs, (e) the Success of this physical education program, f) future of physical education. This unique interdisciplinary program has been implemented in an urban school physical education discipline in East Orange, New Jersey for over 10 years.
During the program the students realize that the bodies go through different experiences. The body becomes a place where a child can recognize in an enjoyable way to express and perceive particular feelings or mental states. Children may distinguish themselves to have high abilities in the social or other domains but low abilities in the field of athletics.
The goal of this program for the individuals is to discover new skills, develop and demonstrate age appropriate mastery level at different tasks, therefore the program consists of 9 to 12 sports, including many game. Each successful experience increases the awareness ability. Engaging in sports and physical activities are social movements involving groups of children in situations such as teams, friends, and recreational settings, which serve as a primary socializing agent for teaching interpersonal skills. As a result of this presentation the audience will reflect and explore how to structure a physical education program to integrate interdisciplinary subjects with philosophical concepts.
Abstract: This paper presents a methodology using
Gravitational Search Algorithm for optimal placement of Phasor
Measurement Units (PMUs) in order to achieve complete
observability of the power system. The objective of proposed
algorithm is to minimize the total number of PMUs at the power
system buses, which in turn minimize installation cost of the PMUs.
In this algorithm, the searcher agents are collection of masses which
interact with each other using Newton’s laws of gravity and motion.
This new Gravitational Search Algorithm based method has been
applied to the IEEE 14-bus, IEEE 30-bus and IEEE 118-bus test
systems. Case studies reveal optimal number of PMUs with better
observability by proposed method.
Abstract: Total hip replacement had been one of the most
successful operations in hip arthritis surgery. The purpose of this
research had been to develop a dynamic hip contact of Thai femoral
bone to analyze the stress distribution on the implant and the strain
distribution on the bone model under daily activities and compared
with the static load simulation. The results showed the different of
maximum von Mises stress 0.14 percent under walking and 0.03
percent under climbing stair condition and the different of equivalent
total strain 0.52 percent under walking and 0.05 percent under
climbing stair condition. The muscular forces should be evaluated
with dynamic condition to reduce the maximum von Mises stress and
equivalent total strain.
Abstract: The research on “The Way of Life of the Civil Servant
Community under the Bureau of the Royal Household” aims to study
1) the way of life of the people who live in the civil servant
community in Tha Wasukri, and 2) the model of community
administration of civil servants under the Bureau of the Royal
Household. This research is conducted qualitatively and
quantitatively by collecting data from interviews, focus group
discussion, participant and non-participant observation along with the
data from questionnaire based on age groups which include elder
group, working age group and youth group.
The result of the research shows that the origin of this community
is related to the history during the Rama V’s reign. It has been a
harbor for the king to boat in any royal ceremonies; this custom is
still maintained until today. The status or position of person who
serves the king in terms of working is often inherited from the bureau
of the Royal Household based on his/her consanguinity and, hence,
further receives the rights to live in the Tha Wasukri area. Therefore,
this community has some special characteristics demonstrating the
way of living influenced by the regulation of the Bureau of the Royal
Household such as respecting elders and interdependence in which
there is internal social organization with the practice of bureaucracy
in going in and out the community. The person who has rights to live
here must be friendly to everybody so that this community will be a
safe place for lives and property. The administration based on the
model of Bangkok for local administration was used as an external
structure only, but the way of living still follows the practice of the
Bureau of the Royal Household.