Abstract: Scrubbing by a liquid spraying is one of the most
effective processes used for removal of fine particles and soluble
gas pollutants (such as SO2, HCl, HF) from the flue gas. There are
many configurations of scrubbers designed to provide contact
between the liquid and gas stream for effectively capturing
particles or soluble gas pollutants, such as spray plates, packed bed
towers, jet scrubbers, cyclones, vortex and venturi scrubbers. The
primary function of venturi scrubber is the capture of fine particles
as well as HCl, HF or SO2 removal with effect of the flue gas
temperature decrease before input to the absorption column. In this
paper, sulfur dioxide (SO2) from flue gas was captured using new
design replacing venturi scrubber (1st degree of wet scrubbing).
The flue gas was prepared by the combustion of the carbon
disulfide solution in toluene (1:1 vol.) in the flame in the reactor.
Such prepared flue gas with temperature around 150°C was
processed in designed laboratory O-element scrubber. Water was
used as absorbent liquid. The efficiency of SO2 removal, pressure
drop and temperature drop were measured on our experimental
device. The dependence of these variables on liquid-gas ratio was
observed. The average temperature drop was in the range from
150°C to 40°C. The pressure drop was increased with increasing of
a liquid-gas ratio, but no too much as for the common venturi
scrubber designs. The efficiency of SO2 removal was up to 70 %.
The pressure drop of our new designed wet scrubber is similar to
commonly used venturi scrubbers; nevertheless the influence of
amount of the liquid on pressure drop is not so significant.
Abstract: This study investigates the suitability of using plastic,
such as polyethylene terephthalate (PET), as a partial replacement of
natural coarse and fine aggregates (for example, brick chips and
natural sand) to produce lightweight concrete for load bearing
structural members. The plastic coarse aggregate (PCA) and plastic
fine aggregate (PFA) were produced from melted polyethylene
terephthalate (PET) bottles. Tests were conducted using three
different water–cement (w/c) ratios, such as 0.42, 0.48, and 0.57,
where PCA and PFA were used as 50% replacement of coarse and
fine aggregate respectively. Fresh and hardened properties of
concrete have been compared for natural aggregate concrete (NAC),
PCA concrete (PCC) and PFA concrete (PFC). The compressive
strength of concrete at 28 days varied with the water–cement ratio for
both the PCC and PFC. Between PCC and PFC, PFA concrete
showed the highest compressive strength (23.7 MPa) at 0.42 w/c ratio
and also the lowest compressive strength (13.7 MPa) at 0.57 w/c
ratio. Significant reduction in concrete density was mostly observed
for PCC samples, ranging between 1977–1924 kg/m³. With the
increase in water–cement ratio PCC achieved higher workability
compare to both NAC and PFC. It was found that both the PCA and
PFA contained concrete achieved the required compressive strength
to be used for structural purpose as partial replacement of the natural
aggregate; but to obtain the desired lower density as lightweight
concrete the PCA is most suited.
Abstract: The material selection in the design of the sandwich
structures is very crucial aspect because of the positive or negative
influences of the base materials to the mechanical properties of the
entire panel. In the literature, it was presented that the selection of the
skin and core materials plays very important role on the behavior of
the sandwich. Beside this, the use of the correct adhesive can make
the whole structure to show better mechanical results and behavior.
In the present work, the static three-point bending tests were
performed on the sandwiches having an aluminum alloy foam core,
the skins made of three different types of fabrics and two different
commercial adhesives (flexible polyurethane and toughened epoxy
based) at different values of support span distances by aiming the
analyses of their flexural performance in terms of absorbed energy,
peak force values and collapse mechanisms. The main results of the
flexural loading are: force-displacement curves obtained after the
bending tests, peak force and absorbed energy values, collapse
mechanisms and adhesion quality. The experimental results presented
that the sandwiches with epoxy based toughened adhesive and the
skins made of S-Glass Woven fabrics indicated the best adhesion
quality and mechanical properties. The sandwiches with toughened
adhesive exhibited higher peak force and energy absorption values
compared to the sandwiches with flexible adhesive. The use of these
sandwich structures can lead to a weight reduction of the transport
vehicles, providing an adequate structural strength under operating
conditions.
Abstract: The number of persons with implanted cardiac
pacemakers (PM) has increased in Western countries. The aim of this
paper is to investigate the possible situations where persons with a
PM may be exposed to extremely low frequency (ELF) electric (EF)
and magnetic fields (MF) that may disturb their PM. Based on our
earlier studies, it is possible to find such high public exposure to EFs
only in some places near 400 kV power lines, where an EF may
disturb a PM in unipolar mode. Such EFs cannot be found near 110
kV power lines. Disturbing MFs can be found near welding
machines. However, we do not have measurement data from welding.
Based on literature and earlier studies at Tampere University of
Technology, it is difficult to find public EF or MF exposure that is
high enough to interfere with PMs.
Abstract: Our globalizing world has become almost a small
village and everyone can access any information at any time.
Everyone lets each other know who does whatever in which place.
We can learn which social events occur in which place in the world.
From the perspective of education, the course notes that a lecturer use
in lessons in a university in any state of America can be examined by
a student studying in a city of Africa or the Far East. This dizzying
communication we have mentioned happened thanks to fast
developments in computer and internet technologies. While these
developments occur in the world, Turkey that has a very large young
population and whose electronic infrastructure rapidly improves has
also been affected by these developments. Nowadays, mobile devices
have become common and thus, it causes to increase data traffic in
social networks. This study was carried out on students in the
different age groups in Selcuk University Vocational School of
Technical Sciences, the Department of Computer Technology.
Students’ opinions about the use of internet and social media were
obtained. The features such as using the Internet and social media
skills, purposes, operating frequency, accessing facilities and tools,
social life and effects on vocational education and so forth were
explored. The positive effects and negative effects of both internet
and social media use on the students in this department and findings
are evaluated from different perspectives and results are obtained. In
addition, relations and differences were found out statistically.
Abstract: High gain broadband plasmonic slot nano-antenna has
been considered. The theory of plasmonic slot nano-antenna (PSNA)
has been developed. The analytical model takes into account also the
electrical field inside the metal due to imperfectness of metal in
optical range, as well as numerical investigation based on finite
element method (FEM) has been realized. It should be mentioned that
Yagi-Uda configuration improves directivity in the plane of structure.
In contrast, in this paper the possibility of directivity improvement of
proposed PSNA in perpendicular plane of structure by using
reflection metallic surface placed under the slot in fixed distance has
been demonstrated. It is well known that a directivity improvement
brings to the antenna gain increasing. This method of diagram
improving is also well known from RF antenna design theory.
Moreover the improvement of directivity in the perpendicular plane
gives more flexibility in such application as improving the light and
atom, ion, molecule interactions by using such type of plasmonic slot
antenna. By the analogy of dipole type optical antennas the widening
of working wavelengths has been realized by using bowtie geometry
of slots, which made the antenna broadband.
Abstract: In the current work, a three-dimensional geometry of a
75% stenosed blood vessel is analyzed. Large eddy simulation (LES)
with the help of a dynamic subgrid scale Smagorinsky model is
applied to model the turbulent pulsatile flow. The geometry, the
transmural pressure and the properties of the blood and the elastic
boundary were based on clinical measurement data. For the flexible
wall model, a thin solid region is constructed around the 75%
stenosed blood vessel. The deformation of this solid region was
modelled as a deforming boundary to reduce the computational cost
of the solid model. Fluid-structure interaction is realized via a twoway
coupling between the blood flow modelled via LES and the
deforming vessel. The information of the flow pressure and the wall
motion was exchanged continually during the cycle by an arbitrary
Lagrangian-Eulerian method. The boundary condition of current time
step depended on previous solutions. The fluctuation of the velocity
in the post-stenotic region was analyzed in the study. The axial
velocity at normalized position Z=0.5 shows a negative value near
the vessel wall. The displacement of the elastic boundary was
concerned in this study. In particular, the wall displacement at the
systole and the diastole were compared. The negative displacement at
the stenosis indicates a collapse at the maximum velocity and the
deceleration phase.
Abstract: This article focuses on upper-extremity musculoskeletal disorders risk assessment model at workplace. In this model are used risk factors that are responsible for musculoskeletal system damage. Based on statistic calculations the model is able to define what risk of MSD threatens workers who are under risk factors. The model is also able to say how MSD risk would decrease if these risk factors are eliminated.
Abstract: This paper presents development results of the method
of seismoacoustic activity monitoring based on usage vibrosensitive
properties of optical fibers. Analysis of Rayleigh backscattering
radiation parameters changes, which take place due to microscopic
seismoacoustic impacts on the optical fiber, allows to determine
seismoacoustic emission sources positions and to identify their types.
Results of using this approach are successful for complex monitoring
of railways.
Abstract: R.C.C. buildings with dual structural system
consisting of shear walls (or braces) and moment resisting frames
have been widely used to resist lateral forces during earthquakes. The
dual systems are designed to resist the total design lateral force in
proportion to their lateral stiffness. The response of combination of
braces and shear walls has not yet been studied. The combination
may prove to be more effective to resist lateral forces during
earthquakes. This concept has been applied to regular R.C.C.
buildings provided with shear walls, braces and their combinations.
Abstract: Essential oils have a significant antimicrobial activity.
These oils can successfully replace the antibiotics. So, the
microorganisms show their inefficiencies resistant for the antibiotics.
For this reason, we study the physicochemical analysis and
antimicrobial activity of the essential oil of Daucus carota. The
extraction is done by steam distillation of water which brought us a
very significant return of 4.65%. The analysis of the essential oil is
performed by GC / MS and has allowed us to identify 32 compounds
in the oil of D. carota flowering tops of Bouira. Three of which are in
the majority are the α-Pinene (22.3%), the carotol (21.7%) and the
limonene (15.8%).
Abstract: Today’s VLSI networks demands for high speed. And
in this work the compact form mathematical model for current mode
signalling in VLSI interconnects is presented.RLC interconnect line
is modelled using characteristic impedance of transmission line and
inductive effect. The on-chip inductance effect is dominant at lower
technology node is emulated into an equivalent resistance. First order
transfer function is designed using finite difference equation, Laplace
transform and by applying the boundary conditions at the source and
load termination. It has been observed that the dominant pole
determines system response and delay in the proposed model. The
novel proposed current mode model shows superior performance as
compared to voltage mode signalling. Analysis shows that current
mode signalling in VLSI interconnects provides 2.8 times better
delay performance than voltage mode. Secondly the damping factor
of a lumped RLC circuit is shown to be a useful figure of merit.
Abstract: This paper aims to investigate the influence of quality
of education and quality of research, provided by local educational
institutions, on the adoption of Information and Communication
Technology (ICT) in managing business operations for companies in
Saudi market. A model was developed and tested using data collected
from 138 Chief Executive Officers (CEOs) of foreign companies in
diverse business sectors. The data is analyzed and managed using
multivariate approaches through standard statistical packages. The
results showed that educational quality has little contribution to the
ICT adoption while research quality seems to play a more prominent
role. These results are analyzed in terms of business environment and
market constraints and further extended to the perceived effectiveness
of applied pedagogical approaches in schools and universities.
Abstract: Robotics brings together several very different
engineering areas and skills. There are various types of robot such as
humanoid robot, mobile robots, remotely operated vehicles, modern
autonomous robots etc. This survey paper advocates the operation of a
robotic car (remotely operated vehicle) that is controlled by a mobile
phone (communicate on a large scale over a large distance even from
different cities). The person makes a call to the mobile phone placed
in the car. In the case of a call, if any one of the button is pressed, a
tone equivalent to the button pressed is heard at the other end of the
call. This tone is known as DTMF (Dual Tone Multiple Frequency).
The car recognizes this DTMF tone with the help of the phone stacked
in the car. The received tone is processed by the Arduino
microcontroller. The microcontroller is programmed to acquire a
decision for any given input and outputs its decision to motor drivers
in order to drive the motors in the forward direction or backward
direction or left or right direction. The mobile phone that makes a call
to cell phone stacked in the car act as a remote.
Abstract: This paper argues nation-building theories that
prioritize democratic governance best explain the successful postindependence
development of Botswana. Three main competing
schools of thought exist regarding the sequencing of policies that
should occur to re-build weakened or failed states. The first posits
that economic development should receive foremost attention, while
democratization and a binding sense of nationalism can wait. A
second group of experts identified constructing a sense of nationalism
among a populace is necessary first, so that the state receives popular
legitimacy and obedience that are prerequisites for development.
Botswana, though, transitioned into a multi-party democracy and
prosperous open economy due to the utilization of traditional
democratic structures, enlightened and accountable leadership, and an
educated technocratic civil service. With these political foundations
already in place when the discovery of diamonds occurred, the
resulting revenues were spent wisely on projects that grew the
economy, improved basic living standards, and attracted foreign
investment. Thus democratization preceded, and therefore provided
an accountable basis for, economic development that might otherwise
have been squandered by greedy and isolated elites to the detriment
of the greater population. Botswana was one of the poorest nations in
the world at the time of its independence in 1966, with little
infrastructure, a dependence on apartheid South Africa for trade, and
a largely subsistence economy. Over the next thirty years, though, its
economy grew the fastest of any nation in the world. The transparent
and judicious use of diamond returns is only a partial explanation, as
the government also pursued economic diversification, mass
education, and rural development in response to public needs.
As nation-building has become a project undertaken by nations
and multilateral agencies such as the United Nations and the North
Atlantic Treaty Organization, Botswana may provide best practices
that others should follow in attempting to reconstruct economically
and politically unstable states.
Abstract: Properties of Portland cement mixtures with various
fractions of metakaolin were studied. 10% of Portland cement CEM I
42.5 R was replaced by different fractions of high reactivity
metakaolin with defined chemical and mineralogical properties.
Various fractions of metakaolin were prepared by jet mill classifying
system. There is a clear trend between fineness of metakaolin and
hydration heat development. Due to metakaolin presence in mixtures
the compressive strength development of mortars is rather slower for
coarser fractions but 28-day flexural strengths are improved for all
fractions of metakaoline used in mixtures compared to reference
sample of pure Portland cement. Yield point, plastic viscosity and
adhesion of fresh pastes are considerably influenced by fineness of
metakaolin used in cement pastes.
Abstract: The objectives of the study were to determine the
marketing mix factors that influencing tourist’s destination decision
making for cultural tourism in the Chonburi province. Both
quantitative and qualitative data were applied in this study. The
samples of 400 cases for quantitative analysis were tourists (both
Thai and foreign) who were interested in cultural tourism in the
Chonburi province, and traveled to cultural sites in Chonburi and 14
representatives from provincial tourism committee of Chonburi and
local tourism experts. Statistics utilized in this research included
frequency, percentage, mean, standard deviation, and multiple
regression analysis. The study found that Thai and foreign tourists
are influenced by different important marketing mix factors. The
important factors for Thai respondents were physical evidence, price,
people, and place at high importance level. For foreign respondents,
physical evidence, price, people, and process were high importance
level, whereas, product, place and promotion were moderate
importance level.
Abstract: The FOSDT (the First Order Shear Deformation
Theory) is taking into consideration to study the static behavior of a
bimorph beam, with a delamination zone between the upper and the
lower layer. The effect of limit conditions and lengths of the
delamination zone are presented in this paper, with a PVDF
piezoelectric material application. A FEM “Finite Element Method”
is used to discretize the beam. In the axial displacement, a
displacement field appears in the debonded zone with inverse effect
between the upper and the lower layer was observed.
Abstract: Two finite element (FEM) models are presented in
this paper to address the random nature of the response of glued
timber structures made of wood segments with variable elastic
moduli evaluated from 3600 indentation measurements. This total
database served to create the same number of ensembles as was the
number of segments in the tested beam. Statistics of these ensembles
were then assigned to given segments of beams and the Latin
Hypercube Sampling (LHS) method was called to perform 100
simulations resulting into the ensemble of 100 deflections subjected
to statistical evaluation. Here, a detailed geometrical arrangement of
individual segments in the laminated beam was considered in the
construction of two-dimensional FEM model subjected to in fourpoint
bending to comply with the laboratory tests. Since laboratory
measurements of local elastic moduli may in general suffer from a
significant experimental error, it appears advantageous to exploit the
full scale measurements of timber beams, i.e. deflections, to improve
their prior distributions with the help of the Bayesian statistical
method. This, however, requires an efficient computational model
when simulating the laboratory tests numerically. To this end, a
simplified model based on Mindlin’s beam theory was established.
The improved posterior distributions show that the most significant
change of the Young’s modulus distribution takes place in laminae in
the most strained zones, i.e. in the top and bottom layers within the
beam center region. Posterior distributions of moduli of elasticity
were subsequently utilized in the 2D FEM model and compared with
the original simulations.
Abstract: In this study, the Compressive strength of concretes
made with Ground Granulated Blast furnace Slag (GGBS),
Pulverised Fuel Ash (PFA), Rice Husk Ash (RHA) and Waste Glass
Powder (WGP) after they were exposed 7800C (exposure duration of
around 60 minutes) and then allowed to cool down gradually in the
furnace for about 280 minutes at water binder ratio of 0.50 was
investigated. GGBS, PFA, RHA and WGP were used to replace up to
20% Portland cement in the control concrete. Test for the
determination of workability, compressive strength and tensile
splitting strength of the concretes were carried out and the results
were compared with control concrete. The test results showed that the
compressive strength decreased by an average of around 30% after
the concretes were exposed to the heating and cooling scenario.