Abstract: In order to perform on-line measuring and detection
of PD signals, a total solution composing of an HFCT, A/D
converter and a complete software package is proposed. The
software package includes compensation of HFCT contribution,
filtering and noise reduction using wavelet transform and soft
calibration routines. The results have shown good performance and
high accuracy.
Abstract: A satured liquid is warmed until boiling in a parallelepipedic boiler. The heat is supplied in a liquid through the horizontal bottom of the boiler, the other walls being adiabatic. During the process of boiling, the liquid evaporates through its free surface by deforming it. This surface which subdivides the boiler into two regions occupied on both sides by the boiled liquid (broth) and its vapor which surmounts it. The broth occupying the region and its vapor the superior region. A two- fluids model is used to describe the dynamics of the broth, its vapor and their interface. In this model, the broth is treated as a monophasic fluid (homogeneous model) and form with its vapor adiphasic pseudo fluid (two-fluid model). Furthermore, the interface is treated as a zone of mixture characterized by superficial void fraction noted α* . The aim of this article is to describe the dynamics of the interface between the boiled fluid and its vapor within a boiler. The resolution of the problem allowed us to show the evolution of the broth and the level of the liquid.
Abstract: This paper presents the experimental results of silicone rubber polymer insulators for 22 kV systems under salt water dip wheel test based on IEC 62217. Straight shed silicone rubber polymer insulators having leakage distance 685 mm were tested continuously 30,000 cycles. One test cycle includes 4 positions, energized, de-energized, salt water dip and deenergized, respectively. For one test cycle, each test specimen remains stationary for about 40 second in each position and takes 8 second for rotate to next position. By visual observation, sever surface erosion was observed on the trunk near the energized end of tested specimen. Puncture was observed on the upper shed near the energized end. In addition, decreasing in hydrophobicity and increasing in hardness were measured on tested specimen comparing with new specimen. Furthermore, chemical analysis by ATR-FTIR was conducted in order to elucidate the chemical change of tested specimens comparing with new specimen.
Abstract: We have developed a microfluidic device system for the continuous producting of nanoparticles, and we have clarified the relationship between the mixing performance of reactors and the particle size. First, we evaluated the mixing performance of reactors by carring out the Villermaux–Dushman reaction and determined the experimental conditions for producing AgCl nanoparticles. Next, we produced AgCl nanoparticles and evaluated the mixing performance and the particle size. We found that as the mixing performance improves the size of produced particles decreases and the particle size distribution becomes sharper. We produced AgCl nanoparticles with a size of 86 nm using the microfluidic device that had the best mixing performance among the three reactors we tested in this study; the coefficient of variation (Cv) of the size distribution of the produced nanoparticles was 26.1%.
Abstract: In most of the cases, natural disasters lead to the
necessity of evacuating people. The quality of evacuation
management is dramatically improved by the use of information
provided by decision support systems, which become indispensable
in case of large scale evacuation operations. This paper presents a
best practice case study. In November 2007, officers from the
Emergency Situations Inspectorate “Crisana" of Bihor County from
Romania participated to a cross-border evacuation exercise, when
700 people have been evacuated from Netherlands to Belgium. One
of the main objectives of the exercise was the test of four different
decision support systems. Afterwards, based on that experience,
software system called TEVAC (Trans Border Evacuation) has been
developed “in house" by the experts of this institution. This original
software system was successfully tested in September 2008, during
the deployment of the international exercise EU-HUROMEX 2008,
the scenario involving real evacuation of 200 persons from Hungary
to Romania. Based on the lessons learned and results, starting from
April 2009, the TEVAC software is used by all Emergency
Situations Inspectorates all over Romania.
Abstract: A major requirement for Grid application developers is ensuring performance and scalability of their applications. Predicting the performance of an application demands understanding its specific features. This paper discusses performance modeling and prediction of multi-agent based simulation (MABS) applications on the Grid. An experiment conducted using a synthetic MABS workload explains the key features to be included in the performance model. The results obtained from the experiment show that the prediction model developed for the synthetic workload can be used as a guideline to understand to estimate the performance characteristics of real world simulation applications.
Abstract: Day by day technology increases and problems
associated with this technology also increase. Several researches
were carried out to investigate the deployment of such material safely
in geotechnical engineering in particular and civil engineering in
general. However, different types of waste material have such as
cement duct, fly ash and slag been proven to be suitable in several
applications. In this research cement dust mixed with different
percentages of sand will be used in some civil engineering
application as will be explained later in this paper throughout filed
and laboratory test. The used mixer (waste material with sand) prove
high performance, durability to environmental condition, low cost
and high benefits. At higher cement dust ratio, small cement ratio is
valuable for compressive strength and permeability. Also at small
cement dust ratio higher cement ratio is valuable for compressive
strength.
Abstract: Artifact rejection plays a key role in many signal processing applications. The artifacts are disturbance that can occur during the signal acquisition and that can alter the analysis of the signals themselves. Our aim is to automatically remove the artifacts, in particular from the Electroencephalographic (EEG) recordings. A technique for the automatic artifact rejection, based on the Independent Component Analysis (ICA) for the artifact extraction and on some high order statistics such as kurtosis and Shannon-s entropy, was proposed some years ago in literature. In this paper we try to enhance this technique proposing a new method based on the Renyi-s entropy. The performance of our method was tested and compared to the performance of the method in literature and the former proved to outperform the latter.
Abstract: The adsorption properties of CO and H2 on iron-based
catalyst with addition of Zr and Ni were investigated using
temperature programmed desorption process. It was found that on the
carburized iron-based catalysts, molecular state and dissociative state
CO existed together. The addition of Zr was preferential for the
molecular state adsorption of CO on iron-based catalyst and the
presence of Ni was beneficial to the dissociative adsorption of CO. On
H2 reduced catalysts, hydrogen mainly adsorbs on the surface iron
sites and surface oxide sites. On CO reduced catalysts, hydrogen
probably existed as the most stable CH and OH species. The addition
of Zr was not benefit to the dissociative adsorption of hydrogen on
iron-based catalyst and the presence of Ni was preferential for the
dissociative adsorption of hydrogen.
Abstract: The inphase/quadrature (I/Q) amplitude and phase
imbalance effects are studied in coherent optical orthogonal
frequency division multiplexing (CO-OFDM) systems. An analytical
model for the I/Q imbalance is developed and supported by
simulation results. The results indicate that the I/Q imbalance degrades the BER performance considerably.
Abstract: HSDPA is a new feature which is introduced in
Release-5 specifications of the 3GPP WCDMA/UTRA standard to
realize higher speed data rate together with lower round-trip times.
Moreover, the HSDPA concept offers outstanding improvement of
packet throughput and also significantly reduces the packet call
transfer delay as compared to Release -99 DSCH. Till now the
HSDPA system uses turbo coding which is the best coding technique
to achieve the Shannon limit. However, the main drawbacks of turbo
coding are high decoding complexity and high latency which makes
it unsuitable for some applications like satellite communications,
since the transmission distance itself introduces latency due to
limited speed of light. Hence in this paper it is proposed to use LDPC
coding in place of Turbo coding for HSDPA system which decreases
the latency and decoding complexity. But LDPC coding increases the
Encoding complexity. Though the complexity of transmitter
increases at NodeB, the End user is at an advantage in terms of
receiver complexity and Bit- error rate. In this paper LDPC Encoder
is implemented using “sparse parity check matrix" H to generate a
codeword at Encoder and “Belief Propagation algorithm "for LDPC
decoding .Simulation results shows that in LDPC coding the BER
suddenly drops as the number of iterations increase with a small
increase in Eb/No. Which is not possible in Turbo coding. Also same
BER was achieved using less number of iterations and hence the
latency and receiver complexity has decreased for LDPC coding.
HSDPA increases the downlink data rate within a cell to a theoretical
maximum of 14Mbps, with 2Mbps on the uplink. The changes that
HSDPA enables includes better quality, more reliable and more
robust data services. In other words, while realistic data rates are
only a few Mbps, the actual quality and number of users achieved
will improve significantly.
Abstract: The main objective of this paper is applying a
comparison between the Wolf Pack Search (WPS) as a newly
introduced intelligent algorithm with several other known algorithms
including Particle Swarm Optimization (PSO), Shuffled Frog
Leaping (SFL), Binary and Continues Genetic algorithms. All
algorithms are applied on two benchmark cost functions. The aim is
to identify the best algorithm in terms of more speed and accuracy in
finding the solution, where speed is measured in terms of function
evaluations. The simulation results show that the SFL algorithm with
less function evaluations becomes first if the simulation time is
important, while if accuracy is the significant issue, WPS and PSO
would have a better performance.
Abstract: Using data of listed Croatian firms from the Zagreb
Stock Exchange we analyze the relationship between firm ownership
(ownership concentration and type) and performance (ROA).
Empirical research was conducted for the period 2003-2010, yielding
with the total of 1,430 observations. Empirical findings based on
dynamic panel analysis indicate that ownership concentration
variable - CR4 is negatively related with performance, i.e. listed firms
with dispersed ownership perform better than firms with concentrated
ownership. Also, the research indicated that foreign controlled listed
firms perform better than domestically controlled firms. Majority
state owned firms perform worse than privately held firms but
dummy variable for privately controlled firms was not statistically
significant in the estimated panel model.
Abstract: With the development of the Internet, E-commerce is
growing at an exponential rate, and lots of online stores are built up to
sell their goods online. A major factor influencing the successful
adoption of E-commerce is consumer-s trust. For new or unknown
Internet business, consumers- lack of trust has been cited as a major
barrier to its proliferation. As web sites provide key interface for
consumer use of E-Commerce, we investigate the design of web site to
build trust in E-Commerce from a design science approach. A
conceptual model is proposed in this paper to describe the ontology of
online transaction and human-computer interaction. Based on this
conceptual model, we provide a personalized webpage design
approach using Bayesian networks learning method. Experimental
evaluation are designed to show the effectiveness of web
personalization in improving consumer-s trust in new or unknown
online store.
Abstract: This investigation examines the effect of the sintering
temperature curve in manufactured nickel powder capillary structure
(wick) for a loop heat pipe (LHP). The sintering temperature curve is
composed of a region of increasing temperature; a region of constant
temperature and a region of declining temperature. The most important
region is that in which the temperature increases, as an index in the
stage in which the temperature increases. The wick of nickel powder is
manufactured in the stage of fixed sintering temperature and the time
between the stage of constant temperature and the stage of falling
temperature. When the slope of the curve in the region of increasing
temperature is unity (equivalent to 10 °C/min), the structure of the
wick is complete and the heat transfer performance is optimal. The
result of experiment test demonstrates that the heat transfer
performance is optimal at 320W; the minimal total thermal resistance
is approximately 0.18°C/W, and the heat flux is 17W/cm2; the internal
parameters of the wick are an effective pore radius of 3.1 μm, a
permeability of 3.25×10-13m2 and a porosity of 71%.
Abstract: Since Cloud environment has appeared as the most powerful
keyword in the computing industry, the growth in VDI (Virtual Desktop
Infrastructure) became remarkable in domestic market. In recent years, with the trend
that mobile devices such as smartphones and pads spread so rapidly, the strengths of
VDI that allows people to access and perform business on the move along with
companies' office needs expedite more rapid spread of VDI.
In this paper, mobile OTP (One-Time Password) authentication method is proposed
to secure mobile device portability through rapid and secure authentication using
mobile devices such as mobile phones or pads, which does not require additional
purchase or possession of OTP tokens of users. To facilitate diverse and wide use of
Services in the future, service should be continuous and stable, and above all, security
should be considered the most important to meet advanced portability and user
accessibility, the strengths of VDI.
Abstract: This paper mainly about the study on one of the
widely used error correcting codes that is Low parity check Codes
(LDPC). In this paper, the Regular LDPC code has been discussed
The LDPC codes explained in this paper is about the Regular Binary
LDPC codes or the Gallager.
Abstract: This paper unifies power optimization approaches in
various energy converters, such as: thermal, solar, chemical, and
electrochemical engines, in particular fuel cells. Thermodynamics
leads to converter-s efficiency and limiting power. Efficiency
equations serve to solve problems of upgrading and downgrading of
resources. While optimization of steady systems applies the
differential calculus and Lagrange multipliers, dynamic optimization
involves variational calculus and dynamic programming. In reacting
systems chemical affinity constitutes a prevailing component of an
overall efficiency, thus the power is analyzed in terms of an active
part of chemical affinity. The main novelty of the present paper in the
energy yield context consists in showing that the generalized heat
flux Q (involving the traditional heat flux q plus the product of
temperature and the sum products of partial entropies and fluxes of
species) plays in complex cases (solar, chemical and electrochemical)
the same role as the traditional heat q in pure heat engines.
The presented methodology is also applied to power limits in fuel
cells as to systems which are electrochemical flow engines propelled
by chemical reactions. The performance of fuel cells is determined by
magnitudes and directions of participating streams and mechanism of
electric current generation. Voltage lowering below the reversible
voltage is a proper measure of cells imperfection. The voltage losses,
called polarization, include the contributions of three main sources:
activation, ohmic and concentration. Examples show power maxima
in fuel cells and prove the relevance of the extension of the thermal
machine theory to chemical and electrochemical systems. The main
novelty of the present paper in the FC context consists in introducing
an effective or reduced Gibbs free energy change between products p
and reactants s which take into account the decrease of voltage and
power caused by the incomplete conversion of the overall reaction.
Abstract: Reduction of Single Input Single Output (SISO) discrete systems into lower order model, using a conventional and an evolutionary technique is presented in this paper. In the conventional technique, the mixed advantages of Modified Cauer Form (MCF) and differentiation are used. In this method the original discrete system is, first, converted into equivalent continuous system by applying bilinear transformation. The denominator of the equivalent continuous system and its reciprocal are differentiated successively, the reduced denominator of the desired order is obtained by combining the differentiated polynomials. The numerator is obtained by matching the quotients of MCF. The reduced continuous system is converted back into discrete system using inverse bilinear transformation. In the evolutionary technique method, Particle Swarm Optimization (PSO) is employed to reduce the higher order model. PSO method is based on the minimization of the Integral Squared Error (ISE) between the transient responses of original higher order model and the reduced order model pertaining to a unit step input. Both the methods are illustrated through numerical example.
Abstract: The aim of this paper is to present the role of
myotonometry in assessment muscle viscoelasticity by measurement
of force index (IF) and stiffness (S) at thigh muscle groups. The
results are used for improve the muscle training. The method is based
on mechanic impulse on the muscle group, that involve a muscle
response like acceleration, speed and amplitude curves. From these
we have information about elasticity, stiffness beginning from
mechanic oscillations of muscle tissue. Using this method offer the
possibility for monitoring the muscle capacity for produce mechanic
energy, that allows a efficiency of movement with a minimal tissue
deformation.