Abstract: Applying corona wind as a novel technique can lead
to a great level of heat and mass transfer augmentation by using very
small amount of energy. Enhancement of forced flow evaporation
rate by applying electric field (corona wind) has been experimentally
evaluated in this study. Corona wind produced by a fine wire
electrode which is charged with positive high DC voltage impinges
to water surface and leads to evaporation enhancement by disturbing
the saturated air layer over water surface. The study was focused on
the effect of corona wind velocity, electrode spacing and air flow
velocity on the level of evaporation enhancement. Two sets of
experiments, i.e. with and without electric field, have been
conducted. Data obtained from the first experiment were used as
reference for evaluation of evaporation enhancement at the presence
of electric field. Applied voltages ranged from corona threshold
voltage to spark over voltage at 1 kV increments. The results showed
that corona wind has great enhancement effect on water evaporation
rate, but its effectiveness gradually diminishes by increasing air flow
velocity. Maximum enhancements were 7.3 and 3.6 for air velocities
of 0.125 and 1.75 m/s, respectively.
Abstract: The general idea behind the filter is to average a pixel
using other pixel values from its neighborhood, but simultaneously to
take care of important image structures such as edges. The main
concern of the proposed filter is to distinguish between any variations
of the captured digital image due to noise and due to image structure.
The edges give the image the appearance depth and sharpness. A
loss of edges makes the image appear blurred or unfocused.
However, noise smoothing and edge enhancement are traditionally
conflicting tasks. Since most noise filtering behaves like a low pass
filter, the blurring of edges and loss of detail seems a natural
consequence. Techniques to remedy this inherent conflict often
encompass generation of new noise due to enhancement.
In this work a new fuzzy filter is presented for the noise reduction
of images corrupted with additive noise. The filter consists of three
stages. (1) Define fuzzy sets in the input space to computes a fuzzy
derivative for eight different directions (2) construct a set of IFTHEN
rules by to perform fuzzy smoothing according to
contributions of neighboring pixel values and (3) define fuzzy sets in
the output space to get the filtered and edged image.
Experimental results are obtained to show the feasibility of the
proposed approach with two dimensional objects.
Abstract: Retinal vascularity assessment plays an important role in diagnosis of ophthalmic pathologies. The employment of digital images for this purpose makes possible a computerized approach and has motivated development of many methods for automated vascular tree segmentation. Metrics based on contingency tables for binary classification have been widely used for evaluating performance of these algorithms and, concretely, the accuracy has been mostly used as measure of global performance in this topic. However, this metric shows very poor matching with human perception as well as other notable deficiencies. Here, a new similarity function for measuring quality of retinal vessel segmentations is proposed. This similarity function is based on characterizing the vascular tree as a connected structure with a measurable area and length. Tests made indicate that this new approach shows better behaviour than the current one does. Generalizing, this concept of measuring descriptive properties may be used for designing functions for measuring more successfully segmentation quality of other complex structures.
Abstract: Fly ash is one of the residues generated in
combustion, and comprises the fine particles that rise with the flue
gases. Ash which does not rise is termed bottom ash [1]. In our
country, it is expected that will be occurred 50 million tons of waste
ash per year until 2020. Released waste from the thermal power
plants is caused very significant problems as known. The fly ashes
can be evaluated by using as adsorbent material.
The purpose of this study is to investigate the possibility of use of
Tuncbilek fly ash like low-cost adsorbents for heavy metal
adsorption. First of all, Tuncbilek fly ash was characterized. For this
purpose; analysis such as sieve analysis, XRD, XRF, SEM and FT-IR
were performed.
Abstract: Image interpolation is a common problem in imaging applications. However, most interpolation algorithms in existence suffer visually the effects of blurred edges and jagged artifacts in the image to some extent. This paper presents an adaptive feature preserving bidirectional flow process, where an inverse diffusion is performed to sharpen edges along the normal directions to the isophote lines (edges), while a normal diffusion is done to remove artifacts (“jaggies") along the tangent directions. In order to preserve image features such as edges, corners and textures, the nonlinear diffusion coefficients are locally adjusted according to the directional derivatives of the image. Experimental results on synthetic images and nature images demonstrate that our interpolation algorithm substantially improves the subjective quality of the interpolated images over conventional interpolations.
Abstract: Hysitron TriboIndenterTM TI 950 system has been
used for studying the local viscoelastic properties of porcine
intervertebral disc end plate by means of nanoscale mechanical
dynamic analysis. The specimen of an endplate was cut from fresh
porcine vertebra dissected from 16 month animal. The lumbar spine
motion segments were dissected and 5 millimeter thick plates of
vertebral body, endplate and annulus fibrosus were prepared for
nanoindentation. The surface of the sample was kept in physiological
solution during nanoindentation experiment. We obtained mechanical
characteristics of different areas of native endplate (endplate middle
and vertebra and annulus fibrosus boundary).
Abstract: The use of polypropylene mesh devices for Pelvic
Organ Prolapse (POP) spread rapidly during the last decade, yet our
knowledge of the mesh-tissue interaction is far from complete. We
aimed to perform a thorough pathological examination of explanted
POP meshes and describe findings that may explain mechanisms of
complications resulting in product excision. We report a spectrum of
important findings, including nerve ingrowth, mesh deformation,
involvement of detrusor muscle with neural ganglia, and
polypropylene degradation. Analysis of these findings may improve
and guide future treatment strategies.
Abstract: This paper presents the application of a signal
intensity independent registration criterion for 2D rigid body
registration of medical images using 1D binary projections. The
criterion is defined as the weighted ratio of two projections. The ratio
is computed on a pixel per pixel basis and weighting is performed by
setting the ratios between one and zero pixels to a standard high
value. The mean squared value of the weighted ratio is computed
over the union of the one areas of the two projections and it is
minimized using the Chebyshev polynomial approximation using
n=5 points. The sum of x and y projections is used for translational
adjustment and a 45deg projection for rotational adjustment. 20 T1-
T2 registration experiments were performed and gave mean errors
1.19deg and 1.78 pixels. The method is suitable for contour/surface
matching. Further research is necessary to determine the robustness
of the method with regards to threshold, shape and missing data.
Abstract: In this paper we present an autoregressive model with
neural networks modeling and standard error backpropagation
algorithm training optimization in order to predict the gross domestic
product (GDP) growth rate of four countries. Specifically we propose
a kind of weighted regression, which can be used for econometric
purposes, where the initial inputs are multiplied by the neural
networks final optimum weights from input-hidden layer after the
training process. The forecasts are compared with those of the
ordinary autoregressive model and we conclude that the proposed
regression-s forecasting results outperform significant those of
autoregressive model in the out-of-sample period. The idea behind
this approach is to propose a parametric regression with weighted
variables in order to test for the statistical significance and the
magnitude of the estimated autoregressive coefficients and
simultaneously to estimate the forecasts.
Abstract: Partitions can play a significant role in minimising cochannel
interference of Wireless LANs by attenuating signals across
room boundaries. This could pave the way towards higher density
deployments in home and office environments through spatial
channel reuse. Yet, due to protocol limitations, the latest incantation
of IEEE 802.11 standard is still unable to take advantage of this fact:
Despite having clearly adequate Signal to Interference Ratio (SIR)
over co-channel neighbouring networks in other rooms, its goodput
falls significantly lower than its maximum in the absence of cochannel
interferers. In this paper, we describe how this situation can
be remedied via modest modifications to the standard.
Abstract: The purpose of this study is to investigate the
efficiency of a double-layer roof in collecting solar energy as an
application to the areas such as raising high-end temperature of
organic Rankine cycle (ORC). The by-product of the solar roof is to
reduce building air-conditioning loads. The experimental apparatus
are arranged to evaluate the effects of the solar roof in absorbing solar
energy. The flow channel is basically formed by an aluminum plate on
top of a plywood plate. The geometric configurations in which the
effects of absorbing energy is analyzed include: a bare uncovered
aluminum plate, a glass-covered aluminum plate, a
glass-covered/black-painted aluminum plate, a plate with variable
lengths, a flow channel with stuffed material (in an attempt on
enhancement of heat conduction), and a flow channel with variable
slanted angles. The experimental results show that the efficiency of
energy collection varies from 0.6 % to 11 % for the geometric
configurations mentioned above. An additional study is carried out
using CFD simulation to investigate the effects of fins on the
aluminum plate. It shows that due to vastly enhanced heat conduction,
the efficiency can reach ~23 % if 50 fins are installed on the aluminum
plate. The study shows that a double-layer roof can efficiently absorb
solar energy and substantially reduce building air-conditioning
loads. On the high end of an organic Rankine cycle, a solar pond is
used to replace the warm surface water of the sea as OTEC (ocean
thermal energy conversion) is the driving energy for the ORC. The
energy collected from the double-layered solar roof can be pumped
into the pond and raise the pond temperature as the pond surface area is
equivalently increased by nearly one-fourth of the total area of the
double-layer solar roof. The effect of raising solar pond temperature is
especially prominent if the double-layer solar roofs are installed in a
community area.
Abstract: In many cases, there are some time lag between the consumption of inputs and the production of outputs. This time lag effect should be considered in evaluating the performance of organizations. Recently, a couple of DEA models were developed for considering time lag effect in efficiency evaluation of research activities. Multi-periods input(MpI) and Multi-periods output(MpO) models are integrate models to calculate simple efficiency considering time lag effect. However, these models can’t discriminate efficient DMUs because of the nature of basic DEA model in which efficiency scores are limited to ‘1’. That is, efficient DMUs can’t be discriminated because their efficiency scores are same. Thus, this paper suggests a super-efficiency model for efficiency evaluation under the consideration of time lag effect based on the MpO model. A case example using a long term research project is given to compare the suggested model with the MpO model.
Abstract: The fast growing accessibility and capability of emerging technologies have fashioned enormous possibilities of designing, developing and implementing innovative teaching methods in the classroom. The global technological scenario has paved the way to new pedagogies in teaching-learning process focusing on technology based learning environment and its impact on student achievement. The present experimental study was conducted to determine the effectiveness of technology based learning environment on student achievement in English as a foreign language. The sample of the study was 90 students of 10th grade of a public school located in Islamabad. A pretest- posttest equivalent group design was used to compare the achievement of the two groups. A Pretest and A posttest containing 50 items each from English textbook were developed and administered. The collected data were statistically analyzed. The results showed that there was a significant difference between the mean scores of Experimental group and the Control group. The performance of Experimental group was better on posttest scores that indicted that teaching through technology based learning environment enhanced the achievement level of the students. On the basis of the results, it was recommended that teaching and learning through information and communication technologies may be adopted to enhance the language learning capability of the students.
Abstract: In this paper we consider a nonlinear feedback control
called augmented automatic choosing control (AACC) using the
gradient optimization automatic choosing functions for nonlinear
systems. Constant terms which arise from sectionwise linearization
of a given nonlinear system are treated as coefficients of a stable
zero dynamics. Parameters included in the control are suboptimally
selected by expanding a stable region in the sense of Lyapunov
with the aid of the genetic algorithm. This approach is applied to
a field excitation control problem of power system to demonstrate
the splendidness of the AACC. Simulation results show that the new
controller can improve performance remarkably well.
Abstract: This study proposes a multi-response surface
optimization problem (MRSOP) for determining the proper choices
of a process parameter design (PPD) decision problem in a noisy
environment of a grease position process in an electronic industry.
The proposed models attempts to maximize dual process responses
on the mean of parts between failure on left and right processes. The
conventional modified simplex method and its hybridization of the
stochastic operator from the hunting search algorithm are applied to
determine the proper levels of controllable design parameters
affecting the quality performances. A numerical example
demonstrates the feasibility of applying the proposed model to the
PPD problem via two iterative methods. Its advantages are also
discussed. Numerical results demonstrate that the hybridization is
superior to the use of the conventional method. In this study, the
mean of parts between failure on left and right lines improve by
39.51%, approximately. All experimental data presented in this
research have been normalized to disguise actual performance
measures as raw data are considered to be confidential.
Abstract: In this paper, the application of multiple Elman neural networks to time series data regression problems is studied. An ensemble of Elman networks is formed by boosting to enhance the performance of the individual networks. A modified version of the AdaBoost algorithm is employed to integrate the predictions from multiple networks. Two benchmark time series data sets, i.e., the Sunspot and Box-Jenkins gas furnace problems, are used to assess the effectiveness of the proposed system. The simulation results reveal that an ensemble of boosted Elman networks can achieve a higher degree of generalization as well as performance than that of the individual networks. The results are compared with those from other learning systems, and implications of the performance are discussed.
Abstract: This paper is about hiding RFID tag identifier (ID)
using handheld device like a cellular phone. By modifying the tag ID
of objects periodically or manually using cellular phone built-in a
RFID reader chip or with a external RFID reader device, we can
prevent other people from gathering the information related with
objects querying information server (like an EPC IS) with a tag ID or
deriving the information from tag ID-s code structure or tracking the
location of the objects and the owner of the objects. In this paper, we
use a cryptographic algorithm for modification and restoring of RFID
tag ID, and for one original tag ID, there are several different
temporary tag ID, periodically.
Abstract: The purpose of this study is to introduce a new
interface program to calculate a dose distribution with Monte Carlo method in complex heterogeneous systems such as organs or tissues
in proton therapy. This interface program was developed under
MATLAB software and includes a friendly graphical user interface
with several tools such as image properties adjustment or results display. Quadtree decomposition technique was used as an image
segmentation algorithm to create optimum geometries from Computed Tomography (CT) images for dose calculations of proton
beam. The result of the mentioned technique is a number of nonoverlapped
squares with different sizes in every image. By this way
the resolution of image segmentation is high enough in and near
heterogeneous areas to preserve the precision of dose calculations
and is low enough in homogeneous areas to reduce the number of
cells directly. Furthermore a cell reduction algorithm can be used to combine neighboring cells with the same material. The validation of this method has been done in two ways; first, in comparison with experimental data obtained with 80 MeV proton beam in Cyclotron
and Radioisotope Center (CYRIC) in Tohoku University and second, in comparison with data based on polybinary tissue calibration method, performed in CYRIC. These results are presented in this paper. This program can read the output file of Monte Carlo code while region of interest is selected manually, and give a plot of dose distribution of proton beam superimposed onto the CT images.
Abstract: As mobile service's subscriber is increasing; mobile
contents services are getting more and more variables. So, mobile
contents development needs not only contents design but also
guideline for just mobile. And when mobile contents are developed, it
is important to pass the limit and restriction of the mobile. The
restrictions of mobile are small browser and screen size, limited
download size and uncomfortable navigation. So each contents of
mobile guideline will be presented for user's usability, easy of
development and consistency of rule. This paper will be proposed
methodology which is each contents of mobile guideline. Mobile web
will be developed by mobile guideline which I proposed.
Abstract: Drilling is the most common machining operation and it forms the highest machining cost in many manufacturing activities including automotive engine production. The outcome of this operation depends upon many factors including utilization of proper cutting tool geometry, cutting tool material and the type of coating used to improve hardness and resistance to wear, and also cutting parameters. With the availability of a large array of tool geometries, materials and coatings, is has become a challenging task to select the best tool and cutting parameters that would result in the lowest machining cost or highest profit rate. This paper describes an algorithm developed to help achieve good performances in drilling operations by automatically determination of proper cutting tools and cutting parameters. It also helps determine machining sequences resulting in minimum tool changes that would eventually reduce machining time and cost where multiple tools are used.