Abstract: Poly (ethylene glycol) (PEG) molecules attached to surfaces have shown high potential as a protein repellent due to their flexibility and highly water solubility. A quartz crystal microbalance recording frequency and dissipation changes (QCM-D) has been used to study the adsorption from aqueous solutions, of lysozyme and α-lactalbumin proteins (the last with and without calcium) onto modified stainless steel surfaces. Surfaces were coated with poly(ethylene imine) (PEI) and silicate before grafting on PEG molecules. Protein adsorption was also performed on the bare stainless steel surface as a control. All adsorptions were conducted at 23°C and pH 7.2. The results showed that the presence of PEG molecules significantly reduced the adsorption of lysozyme and α- lactalbumin (with calcium) onto the stainless steel surface. By contrast, and unexpected, PEG molecules enhanced the adsorption of α-lactalbumin (without calcium). It is suggested that the PEG -α- lactalbumin hydrophobic interaction plays a dominant role which leads to protein aggregation at the surface for this latter observation. The findings also lead to the general conclusion that PEG molecules are not a universal protein repellent. PEG-on-PEI surfaces were better at inhibiting the adsorption of lysozyme and α-lactalbumin (with calcium) than with PEG-on-silicate surfaces.
Abstract: This paper deals with new concept of using compressed atmospheric air as a zero pollution power source for running motorbikes. The motorbike is equipped with an air turbine in place of an internal combustion engine, and transforms the energy of the compressed air into shaft work. The mathematical modeling and performance evaluation of a small capacity compressed air driven vaned type novel air turbine is presented in this paper. The effect of isobaric admission and adiabatic expansion of high pressure air for different rotor to casing diameter ratios with respect to different vane angles (number of vanes) have been considered and analyzed. It is found that the shaft work output is optimum for some typical values of rotor / casing diameter ratios at a particular value of vane angle (no. of vanes). In this study, the maximum power is obtained as 4.5kW - 5.3kW (5.5-6.25 HP) when casing diameter is taken 100 mm, and rotor to casing diameter ratios are kept from 0.65 to 0.55. This value of output is sufficient to run motorbike.
Abstract: In this study, aeroelastic response and performance
analyses have been conducted for a 5MW-Class composite wind
turbine blade model. Advanced coupled numerical method based on
computational fluid dynamics (CFD) and computational flexible
multi-body dynamics (CFMBD) has been developed in order to
investigate aeroelastic responses and performance characteristics of
the rotating composite blade. Reynolds-Averaged Navier-Stokes
(RANS) equations with k-ω SST turbulence model were solved for
unsteady flow problems on the rotating turbine blade model. Also,
structural analyses considering rotating effect have been conducted
using the general nonlinear finite element method. A fully implicit
time marching scheme based on the Newmark direct integration
method is applied to solve the coupled aeroelastic governing equations
of the 3D turbine blade for fluid-structure interaction (FSI) problems.
Detailed dynamic responses and instantaneous velocity contour on the
blade surfaces which considering flow-separation effects were
presented to show the multi-physical phenomenon of the huge rotating
wind- turbine blade model.
Abstract: This research project is developed in order to study
managerial styles of modern Thai executives. The thorough
understanding will lead to continuous improvement and efficient
performance of Thai business organizations. Regarding managerial
skills, Thai executives focus heavily upon human skills. Also, the
negotiator roles are most emphasis in their management. In addition,
Thai executives pay most attention to the fundamental management
principles including Harmony and Unity of Direction of the
organizations. Moreover, the management techniques, consisting of
Team work and Career Planning are of their main concern. Finally,
Thai executives wish to enhance their firms- image and employees-
morale through conducting the ethical and socially responsible
activities. The major tactic deployed to stimulate employees- ethical
behaviors and mindset is Code of Ethics development.
Abstract: The approach proposed here is oriented in the direction of fuzzy system for the analysis and the synthesis of intelligent climate controllers, the simulation of the internal climate of the greenhouse is achieved by a linear model whose coefficients are obtained by identification. The use of fuzzy logic controllers for the regulation of climate variables represents a powerful way to minimize the energy cost. Strategies of reduction and optimization are adopted to facilitate the tuning and to reduce the complexity of the controller.
Abstract: Renewed interest in propeller propulsion on aircraft
configurations combined with higher propeller loads lead to the question how the effects of the propulsion on model support disturbances
should be accounted for. In this paper, the determination of engine power effects on support interference of sting-mounted models is
demonstrated by a measurement on a four-engine turboprop aircraft.
CFD results on a more generic model are presented in order to clarify
the possible mechanism behind engine power effects on support
interference. The engine slipstream induces a local change in angle
of sideslip at the model sting thereby influencing the sting near-field and far-field effects. Whether or not the net result of these changes
in the disturbance pattern leads to a significant engine power effect depends on the configuration of the wind tunnel model and the test
setup.
Abstract: This paper presents a multi-objective order allocation
planning problem with the consideration of various real-world
production features. A novel hybrid intelligent optimization model,
integrating a multi-objective memetic optimization process, a Monte
Carlo simulation technique and a heuristic pruning technique, is
proposed to handle this problem. Experiments based on industrial data
are conducted to validate the proposed model. Results show that (1)
the proposed model can effectively solve the investigated problem by
providing effective production decision-making solutions, which
outperformsan NSGA-II-based optimization process and an industrial
method.
Abstract: This paper presented two new efficient algorithms
for contour approximation. The proposed algorithm is compared
with Ramer (good quality), Triangle (faster) and Trapezoid (fastest)
in this work; which are briefly described. Cartesian co-ordinates of
an input contour are processed in such a manner that finally
contours is presented by a set of selected vertices of the edge of the
contour. In the paper the main idea of the analyzed procedures for
contour compression is performed. For comparison, the mean
square error and signal-to-noise ratio criterions are used.
Computational time of analyzed methods is estimated depending on
a number of numerical operations. Experimental results are
obtained both in terms of image quality, compression ratios, and
speed. The main advantages of the analyzed algorithm is small
numbers of the arithmetic operations compared to the existing
algorithms.
Abstract: In a liberalized electricity market, it is not surprising
that different customers require different power quality (PQ) levels at
different price. Power quality related to several power disturbances is
described by many parameters, so how to define a comprehensive
hierarchy evaluation system of power quality (PQCHES) has become
a concerned issue. In this paper, based on four electromagnetic
compatibility (EMC) levels, the numerical range of each power
disturbance is divided into five grades (Grade I –Grade V), and the
“barrel principle" of power quality is used for the assessment of
overall PQ performance with only one grade indicator. A case study
based on actual monitored data of PQ shows that the site PQ grade
indicates the electromagnetic environment level and also expresses the
characteristics of loads served by the site.
The shortest plank principle of PQ barrel is an incentive
mechanism, which can combine with the rewards/penalty mechanism
(RPM) of consumed energy “on quality demand", to stimulate utilities
to improve the overall PQ level and also stimulate end-user more
“smart" under the infrastructure of future SmartGrid..
Abstract: The aim of this study was to remove the two principal
noises which disturb the surface electromyography signal
(Diaphragm). These signals are the electrocardiogram ECG artefact
and the power line interference artefact. The algorithm proposed
focuses on a new Lean Mean Square (LMS) Widrow adaptive
structure. These structures require a reference signal that is correlated
with the noise contaminating the signal. The noise references are
then extracted : first with a noise reference mathematically
constructed using two different cosine functions; 50Hz (the
fundamental) function and 150Hz (the first harmonic) function for
the power line interference and second with a matching pursuit
technique combined to an LMS structure for the ECG artefact
estimation. The two removal procedures are attained without the use
of supplementary electrodes. These techniques of filtering are
validated on real records of surface diaphragm electromyography
signal. The performance of the proposed methods was compared with
already conducted research results.
Abstract: The experiment was then conducted to investigate the
effect of cassava peel addition in the concentrate on the performance
of lactating dairy cows. Twenty four Holstein Friesian crossbred
(>87.5% Holstein Friesian) lactating dairy cows in mid lactation;
averaging 12.2+2.1 kg of milk, 119+45 days in milk, 44.1+6.2
months old and 449+33 kg live weight, were stratified for milk yield,
days in milk, age, stage of lactation and body weight, and then
randomly allocated to three treatment groups. The first, second and
third groups were fed concentrates containing the respective cassava
peel, 0, 20 and 40%. All cows were fed ad libitum corn silage and
freely access to clean water. Dry matter intake, 4%FCM, milk
composition and body weight change were affected (P
Abstract: Self-compacting concrete (SCC), a new kind of high
performance concrete (HPC) have been first developed in Japan in
1986. The development of SCC has made casting of dense
reinforcement and mass concrete convenient, has minimized noise.
Fresh self-compacting concrete (SCC) flows into formwork and
around obstructions under its own weight to fill it completely and
self-compact (without any need for vibration), without any
segregation and blocking. The elimination of the need for
compaction leads to better quality concrete and substantial
improvement of working conditions. SCC mixes generally have a
much higher content of fine fillers, including cement, and produce
excessively high compressive strength concrete, which restricts its
field of application to special concrete only. To use SCC mixes in
general concrete construction practice, requires low cost materials to
make inexpensive concrete.
Rice husk ash (RHA) has been used as a highly reactive
pozzolanic material to improve the microstructure of the interfacial
transition zone (ITZ) between the cement paste and the aggregate in
self compacting concrete. Mechanical experiments of RHA blended
Portland cement concretes revealed that in addition to the pozzolanic
reactivity of RHA (chemical aspect), the particle grading (physical
aspect) of cement and RHA mixtures also exerted significant
influences on the blending efficiency.
The scope of this research was to determine the usefulness of Rice
husk ash (RHA) in the development of economical self compacting
concrete (SCC). The cost of materials will be decreased by reducing
the cement content by using waste material like rice husk ash instead
of.
This paper presents a study on the development of Mechanical
properties up to 180 days of self compacting and ordinary concretes
with rice-husk ash (RHA), from a rice paddy milling industry in
Rasht (Iran). Two different replacement percentages of cement by
RHA, 10%, and 20%, and two different water/cementicious material
ratios (0.40 and 0.35), were used for both of self compacting and
normal concrete specimens. The results are compared with those of
the self compacting concrete without RHA, with compressive,
flexural strength and modulus of elasticity. It is concluded that RHA
provides a positive effect on the Mechanical properties at age after
60 days.
Base of the result self compacting concrete specimens have higher
value than normal concrete specimens in all test except modulus of
elasticity. Also specimens with 20% replacement of cement by RHA
have the best performance.
Abstract: This paper focuses on robust design and optimization
of industrial production wastes. Past literatures were reviewed to case
study Clamason Industries Limited (CIL) - a leading ladder-tops
manufacturer. A painstaking study of the firm-s practices at the shop
floor revealed that Over-production, Waiting time, Excess inventory,
and Defects are the major wastes that are impeding their progress and
profitability. Design expert8 software was used to apply Taguchi
robust design and response surface methodology in order to model,
analyse and optimise the wastes cost in CIL. Waiting time and overproduction
rank first and second in contributing to the costs of wastes
in CIL. For minimal wastes cost the control factors of overproduction,
waiting-time, defects and excess-inventory must be set at
0.30, 390.70, 4 and 55.70 respectively for CIL. The optimal value of
cost of wastes for the months studied was 22.3679. Finally, a
recommendation was made that for the company to enhance their
profitability and customer satisfaction, they must adopt the Shingeo
Shingo-s Single Minute Exchange of Dies (SMED), which will
immediately tackle the waste of waiting by drastically reducing their
setup time.
Abstract: This paper describes a new measuring algorithm for
three-dimensional (3-D) braided composite material .Braided angle is
an important parameter of braided composites. The objective of this
paper is to present an automatic measuring system. In the paper, the
algorithm is performed by using vcµ6.0 language on PC. An
advanced filtered algorithm for image of 3-D braided composites
material performs has been developed. The procedure is completely
automatic and relies on the gray scale information content of the
images and their local wavelet transform modulus maxims.
Experimental results show that the proposed method is feasible.
The algorithm was tested on both carbon-fiber and glass-fiber
performs.
Abstract: Chronic hepatitis B can evolve to cirrhosis and liver
cancer. Interferon is the only effective treatment, for carefully selected
patients, but it is very expensive. Some of the selection criteria are
based on liver biopsy, an invasive, costly and painful medical procedure.
Therefore, developing efficient non-invasive selection systems,
could be in the patients benefit and also save money. We investigated
the possibility to create intelligent systems to assist the Interferon
therapeutical decision, mainly by predicting with acceptable accuracy
the results of the biopsy. We used a knowledge discovery in integrated
medical data - imaging, clinical, and laboratory data. The resulted
intelligent systems, tested on 500 patients with chronic hepatitis
B, based on C5.0 decision trees and boosting, predict with 100%
accuracy the results of the liver biopsy. Also, by integrating the other
patients selection criteria, they offer a non-invasive support for the
correct Interferon therapeutic decision. To our best knowledge, these
decision systems outperformed all similar systems published in the
literature, and offer a realistic opportunity to replace liver biopsy in
this medical context.
Abstract: Dextran is a D-glucose polymer which is produced by
Leuconostoc mesenteroides grown in a sucrose-rich media. The
organism was obtained from the Persian Type Culture Collection
(PTCC) and was transferred in MRS broth medium at 30°C and pH
6.8 for 24 h. After preparation of inoculums, organisms were
inoculated into five liquid fermentation media containing either
molasses or cheese whey or different combinations of cheese whey
and molasses. After certain fermentation period, the produced
dextran was separated and dried. Dextran yield was calculated and
significant differences in different media were observed.
Furthermore, FT-IR analysis was performed and the results showed
that there were no significant differences in the produced dextran
structures.
Abstract: Amarindra-vinitchai-mahaisuraya Bhiman throne hall
is one of the most significant throne halls in the grand palace in the
Ratthanakosin city situated in Bangkok, Thailand. This is the first
group of throne halls built in order to serve as a place for meetings,
performing state affairs and royal duties until the present time. The
structure and pattern of architectural design including the decoration
and interior design of the throne hall obviously exhibits and convey
the status of the king under the context of Thai society in the early
period of Ratthanakosin era. According to the tradition of ruling the
kingdom in absolute monarchy which had been in place since
Ayutthaya era (A.D.1350-1767), the king was deemed as Deva Raja,
the highest power and authority over the kingdom and as the greatest
emperor of the universe (Chakkravatin). The architectural design
adopted the concept of “Prasada" or Viman which served as the
dwelling place of the gods and was presented in the form of “Thai
traditional architecture" For the interior design of the throne hall, it
had been adopted to be the heaven and the centre of the Universe in
line with the cosmological beliefs of ancient people described in
scripture Tribhumikatha (Tri Bhumi) written by Phra Maha Thamma
Raja (Phraya Lithai) of the Sukhothai era (A.D.1347-1368).
According to this belief, the throne hall had been designed to represent
mount Meru, the central of the universe. On the top end of Mount
Meru is situated the Viman and dwelling place of Indra who is the king
of gods according to the idea of Deva Raja (the king god Avatar). At
the same time, Indra also existed as the king of the universe
simultaneously.
Abstract: We study the performance of compressed beamforming
weights feedback technique in generalized triangular decomposition
(GTD) based MIMO system. GTD is a beamforming technique that
enjoys QoS flexibility. The technique, however, will perform at its
optimum only when the full knowledge of channel state information
(CSI) is available at the transmitter. This would be impossible in
the real system, where there are channel estimation error and limited
feedback. We suggest a way to implement the quantized beamforming
weights feedback, which can significantly reduce the feedback data,
on GTD-based MIMO system and investigate the performance of
the system. Interestingly, we found that compressed beamforming
weights feedback does not degrade the BER performance of the
system at low input power, while the channel estimation error
and quantization do. For comparison, GTD is more sensitive to
compression and quantization, while SVD is more sensitive to the
channel estimation error. We also explore the performance of GTDbased
MU-MIMO system, and find that the BER performance starts
to degrade largely at around -20 dB channel estimation error.
Abstract: The article deals with pneumatic and hot wire
anemometry measurement on subsonic axi-symmetric air ejector.
Performances of the ejector with and without pulsations of primary
flow are compared, measuring of characteristic pressures and mass
flow rates are performed and ejector efficiency is evaluated. The
pulsations of primary flow are produced by a synthetic jet generator,
which is placed in the supply line of the primary flow just in front of
the primary nozzle. The aim of the pulsation is to intensify the
mixing process. In the article we present: Pressure measuring of
pulsation on the mixing chamber wall, behind the mixing chamber
and behind the diffuser measured by fast pressure transducers and
results of hot wire anemometry measurement. It was found out that
using of primary flow pulsations yields higher back pressure behind
the ejector and higher efficiency. The processes in this ejector and
influences of primary flow pulsations on the mixing processes are
described.
Abstract: The indistinctness of the manufacturing processes makes that a parts cannot be realized in an absolutely exact way towards the specifications on the dimensions. It is thus necessary to assume that the effectively realized product has to belong in a very strict way to compatible intervals with a correct functioning of the parts. In this paper we present an approach based on mixing tow different characteristics theories, the fuzzy system and Petri net system. This tool has been proposed to model and control the quality in an assembly system. A robust command of a mechanical assembly process is presented as an application. This command will then have to maintain the specifications interval of parts in front of the variations. It also illustrates how the technique reacts when the product quality is high, medium, or low.