Abstract: One of the main purposes of designing bucklingrestrained
braces is the fact that the entire lateral load is wasted by
the braces, the entire gravitational load is moved to the foundation
through the beams, and the columns can be moved to the foundation.
In other words, braces are designed for bearing lateral load. In the
implementation of the structure, it should be noted that the
implementation of various parts of the structure must be conducted in
such a way that the buckling-restrained braces would not bear the
gravitational load. Moreover, this type of brace has been investigated
under impact loading, and the design goals of designing method
(direct motion) are controlled under impact loading. The results of
dynamic analysis are shown as the relocation charts of the floors and
switch between the floors. Finally, the results are compared with each
other.
Abstract: This work aims to investigate the structure–property
relationship in ternary nanocomposites consisting of polypropylene
as the matrix, polyamide 66 as the minor phase and treated nanoclay
DELLITE 67G as the reinforcement. All PP/PA66/Nanoclay systems
with polypropylene grafted maleic anhydride PP-g-MAH as a
compatibilizer were prepared via melt compounding and
characterized in terms of nanoclay content. Morphological structure
was investigated by scanning electron microscopy. The rheological
behavior of the nanocomposites was determined by various methods,
viz melt flow index (MFI) and parallel plate rheological
measurements. The PP/PP-g-MAH/PA66 nanocomposites showed a homogeneous
morphology supporting the compatibility improvement between PP,
PA66, and nanoclay. SEM results revealed the formation of
nanocomposites as the nanoclay was intercalated and exfoliated. In
the ternary nanocomposites, the rheological behavior showed that, the
complex viscosity is increased with increasing the nanoclay. The results showed that the use of nanoclay affects the variations
of storage modulus (G′), loss modulus (G″) and the melt elasticity.
Abstract: This paper aims to analysis the behavior of DC corona
discharge in wire-to-plate electrostatic precipitators (ESP). Currentvoltage
curves are particularly analyzed. Experimental results show
that discharge current is strongly affected by the applied voltage. The proposed method of current identification is to use the method
of least squares. Least squares problems that of into two categories:
linear or ordinary least squares and non-linear least squares,
depending on whether or not the residuals are linear in all unknowns.
The linear least-squares problem occurs in statistical regression
analysis; it has a closed-form solution. A closed-form solution (or
closed form expression) is any formula that can be evaluated in a
finite number of standard operations. The non-linear problem has no
closed-form solution and is usually solved by iterative.
Abstract: Game-based learning can enhance the learning
motivation of students and provide a means for them to learn through
playing games. This study used augmented reality technology to
develop an interactive card game as a game-based teaching aid for
delivering elementary school science course content with the aim of
enhancing student learning processes and outcomes. Through playing
the proposed card game, students can familiarize themselves with
appearance, features, and foraging behaviors of insects. The system
records the actions of students, enabling teachers to determine their
students’ learning progress. In this study, 37 students participated in an
assessment experiment and provided feedback through questionnaires.
Their responses indicated that they were significantly more motivated
to learn after playing the game, and their feedback was mostly
positive.
Abstract: The objective of this study was to examine the
relationship between transformational leadership and innovative work
behavior and to evaluate the mediating role of leader-member
exchange relationships (LMX) on the assumed relationship. This
study has focused on the suggestion that LMX might emerge through
transformational leadership behaviors and thus could mediate the
relationship between transformational leadership and innovative
behavior. A cross-sectional survey research has been conducted on
the relationship these leadership approaches and their impact on
organizational HRM-outcomes have been conducted on two
organizations operating in the technical sector in Istanbul-Turkey.
The results of the research have supported the hypotheses.
Transformational leadership was positively related to the innovative
behaviors and LMX emerged to mediate that relationship.
Abstract: Bottom ash from Municipal Solid Waste Incineration
(MSWI) can be viewed as a typical granular material because these
industrial by-products result from the incineration of various
domestic wastes. MSWI bottom ash is mainly used in road
engineering in substitution of the traditional natural aggregates. As
the characterization of their mechanical behavior is essential in order
to use them, specific studies have been led over the past few years. In
the first part of this paper, the mechanical behavior of MSWI bottom
ash is studied with triaxial tests. After, analysis of the experiment
results, the simulation of triaxial tests is carried out by using the
software package CESAR-LCPC. As the first approach in modeling
of this new class material, the Mohr-Coulomb model was chosen to
describe the evolution of material under the influence of external
mechanical actions.
Abstract: In India, most of the pavement is laid by bituminous
road and the consumption of binder is high for pavement construction
and also modified binders are used to satisfy any specific pavement
requirement. Since the binders are visco-elastic material which is
having the mechanical properties of binder transition from viscoelastic
solid to visco-elastic fluid. In this paper, two different
protocols were used to measure the viscosity property of binder using
a Brookfield Viscometer and there is a need to find the appropriate
mixing and compaction temperatures of various types of binders
which can result in complete aggregate coating and adequate field
density of HMA mixtures. The aim of this work is to find the
transition temperature from Non-Newtonian behavior to Newtonian
behavior of the binder by adopting a steady shear protocol and the
shear rate ramp protocol. The transition from non-Newtonian to
Newtonian can occur through an increase of temperature and shear of
the material. The test has been conducted for unmodified binder VG
30. The transition temperature was found in the unmodified binder
VG is 120oC. Therefore, the application of both modified binder and
unmodified binder in the pavement construction needs to be studied
properly by considering temperature and traffic loading factors of the
respective project site.
Abstract: The main objective of this research is to describe the
relationship between organizational climate and organizational
citizenship behavior. In order to examine this relationship, a research
is intended to be carried out in relevant institutions and organizations
operating in the health sector in Turkey. It will be researched that
whether there is a statistically significant relationship between
organizational climate and organizational citizenship behavior
through elated scientific research methods and statistical analysis. In
addition, relationships between the dimensions of organizational
climate and organizational citizenship behavior subscales will be
questioned statistically.
Abstract: The statistical study has become indispensable for various fields of knowledge. Not any different, in Geotechnics the study of probabilistic and statistical methods has gained power considering its use in characterizing the uncertainties inherent in soil properties. One of the situations where engineers are constantly faced is the definition of a probability distribution that represents significantly the sampled data. To be able to discard bad distributions, goodness-of-fit tests are necessary. In this paper, three non-parametric goodness-of-fit tests are applied to a data set computationally generated to test the goodness-of-fit of them to a series of known distributions. It is shown that the use of normal distribution does not always provide satisfactory results regarding physical and behavioral representation of the modeled parameters.
Abstract: Lightweight and efficient structures have the aim to
enhance the efficiency of the components in various industries.
Toward this end, composites are one of the most widely used
materials because of durability, high strength and modulus, and low
weight. One type of the advanced composites is grid-stiffened
composite (GSC) structures, which have been extensively considered
in aerospace, automotive, and aircraft industries. They are one of the
top candidates for replacing some of the traditional components,
which are used here. Although there are a good number of published
surveys on the design aspects and fabrication of GSC structures, little
systematic work has been reported on their material modification to
improve their properties, to our knowledge. Matrix modification
using nanoparticles is an effective method to enhance the flexural
properties of the fibrous composites. In the present study, a silanecoupling
agent (3-glycidoxypropyltrimethoxysilane/3-GPTS) was
introduced onto the silica (SiO2) nanoparticle surface and its effects
on the three-point flexural response of isogrid E-glass/epoxy
composites were assessed. Based on the Fourier Transform Infrared
Spectrometer (FTIR) spectra, it was inferred that the 3-GPTS
coupling agent was successfully grafted onto the surface of SiO2
nanoparticles after modification. Flexural test revealed an
improvement of 16%, 14%, and 36% in stiffness, maximum load and
energy absorption of the isogrid specimen filled with 3 wt.% 3-
GPTS/SiO2 compared to the neat one. It would be worth mentioning
that in these structures, considerable energy absorption was observed
after the primary failure related to the load peak. In addition, 3-
GPTMS functionalization had a positive effect on the flexural
behavior of the multiscale isogrid composites. In conclusion, this
study suggests that the addition of modified silica nanoparticles is a
promising method to improve the flexural properties of the gridstiffened
fibrous composite structures.
Abstract: Mineral product, waste concrete (fine aggregates),
waste in the optical field, industry, and construction employ separators
to separate solids and classify them according to their size. Various
sorting machines are used in the industrial field such as those operating
under electrical properties, centrifugal force, wind power, vibration,
and magnetic force. Study on separators has been carried out to
contribute to the environmental industry. In this study, we perform
CFD analysis for understanding the basic mechanism of the separation
of waste concrete (fine aggregate) particles from air with a machine
built with a rotor with blades. In CFD, we first performed
two-dimensional particle tracking for various particle sizes for the
model with 1 degree, 1.5 degree, and 2 degree angle between each
blade to verify the boundary conditions and the method of rotating
domain method to be used in 3D. Then we developed 3D numerical
model with ANSYS CFX to calculate the air flow and track the
particles. We judged the capability of particle separation for given size
by counting the number of particles escaping from the domain toward
the exit among 10 particles issued at the inlet. We confirm that
particles experience stagnant behavior near the exit of the rotating
blades where the centrifugal force acting on the particles is in balance
with the air drag force. It was also found that the minimum particle
size that can be separated by the machine with the rotor is determined
by its capability to stay at the outlet of the rotor channels.
Abstract: This paper sets out a behavioral macro-model of a
Merged PiN and Schottky (MPS) diode based on silicon carbide
(SiC). This model holds good for both static and dynamic electrothermal
simulations for industrial applications. Its parameters have
been worked out from datasheets curves by drawing on the
optimization method: Simulated Annealing (SA) for the SiC MPS
diodes made available in the industry. The model also adopts the
Analog Behavioral Model (ABM) of PSPICE in which it has been
implemented. The thermal behavior of the devices was also taken
into consideration by making use of Foster’ canonical network as
figured out from electro-thermal measurement provided by the
manufacturer of the device.
Abstract: This experimental study consists of a characterization
of epoxy grout where an amount of 2% of graphene nanoplatelets
particles were added to commercial epoxy resin to evaluate their
behavior regarding neat epoxy resin. Compressive tests, tensile tests
and flexural tests were conducted to study the effect of graphene
nanoplatelets on neat epoxy resin. By comparing graphene-based and
neat epoxy grout, there is no significant increase of strength due to
weak interface in the graphene nanoplatelets/epoxy composites.
From this experiment, the tension and flexural strength of graphenebased
epoxy grouts is slightly lower than ones of neat epoxy grout.
Nevertheless, the addition of graphene has produced more consistent
results according to a smaller standard deviation of strength.
Furthermore, the graphene has also improved the ductility of the
grout, hence reducing its brittle behaviour. This shows that the
performance of graphene-based grout is reliably predictable and able
to minimise sudden rupture. This is important since repair design of
damaged pipeline is of deterministic nature.
Abstract: Web Usage Mining is the application of data mining
techniques to find usage patterns from web log data, so as to grasp
required patterns and serve the requirements of Web-based
applications. User’s expertise on the internet may be improved by
minimizing user’s web access latency. This may be done by
predicting the future search page earlier and the same may be prefetched
and cached. Therefore, to enhance the standard of web
services, it is needed topic to research the user web navigation
behavior. Analysis of user’s web navigation behavior is achieved
through modeling web navigation history. We propose this technique
which cluster’s the user sessions, based on the K-medoids technique.
Abstract: Over the last two decades, externally bonded fiber
reinforced polymer (FRP) composites bonded to concrete substrates
has become a popular method for strengthening reinforced concrete
(RC) highway and railway bridges. Such structures are exposed to
severe cyclic loading throughout their lifetime often resulting in
fatigue damage to structural components and a reduction in the
service life of the structure. Since experimental and numerical results
on the fatigue performance of FRP-to-concrete joints are still limited,
the current research focuses on assessing the fatigue performance of
externally bonded FRP-to-concrete joints using a direct shear test.
Some early results indicate that the stress ratio and the applied cyclic
stress level have a direct influence on the fatigue life of the externally
bonded FRP. In addition, a calibrated finite element model is
developed to provide further insight into the influence of certain
parameters such as: concrete strength, FRP thickness, number of
cycles, frequency, and stiffness on the fatigue life of the FRP-toconcrete
joints.
Abstract: This paper focuses on the mathematical modeling for
solidification of Al alloy in a cube mold cavity to study the
solidification behavior of casting process. The parametric
investigation of solidification process inside the cavity was
performed by using computational solidification/melting model
coupled with Volume of fluid (VOF) model. The implicit filling
algorithm is used in this study to understand the overall process from
the filling stage to solidification in a model metal casting process.
The model is validated with past studied at same conditions. The
solidification process is analyzed by including the effect of pouring
velocity as well as natural convection from the wall and geometry of
the cavity. These studies show the possibility of various defects
during solidification process.
Abstract: Opportunistic Routing (OR) increases the
transmission reliability and network throughput. Traditional routing
protocols preselects one or more predetermined nodes before
transmission starts and uses a predetermined neighbor to forward a
packet in each hop. The opportunistic routing overcomes the
drawback of unreliable wireless transmission by broadcasting one
transmission can be overheard by manifold neighbors. The first
cooperation-optimal protocol for Multirate OR (COMO) used to
achieve social efficiency and prevent the selfish behavior of the
nodes. The novel link-correlation-aware OR improves the
performance by exploiting the miscellaneous low correlated forward
links. Context aware Adaptive OR (CAOR) uses active suppression
mechanism to reduce packet duplication. The Context-aware OR
(COR) can provide efficient routing in mobile networks. By using
Cooperative Opportunistic Routing in Mobile Ad hoc Networks
(CORMAN), the problem of opportunistic data transfer can be
tackled. While comparing to all the protocols, COMO is the best as it
achieves social efficiency and prevents the selfish behavior of the
nodes.
Abstract: Escherichia coli (E. coli) is the most isolated bacteria
from blood circulation of septicemic calves. Given the prevalence of
septicemia in animals and its economic importance in veterinary
practice, better understanding of changes in clinical signs following
disease, may contribute to early detection of disorder. The present
study has been carried out to detect changes of clinical signs in
induced sepsis in calves with E. coli. Colisepticemia has been
induced in 10 twenty-day old healthy Holstein- Frisian calves with
intravenous injection of 1.5 X 109 colony forming units (cfu) of
O111:H8 strain of E. coli. Clinical signs including rectal temperature,
heart rate, respiratory rate, shock, appetite, sucking reflex, feces
consistency, general behavior, dehydration and standing ability were
recorded in experimental calves during 24 hours after induction of
colisepticemia. Blood culture was also carried out from calves four
times during experiment. ANOVA with repeated measure is used to
see changes of calves’ clinical signs to experimental colisepticemia,
and values of P≤ 0.05 was considered statistically significant. Mean
values of rectal temperature and heart rate as well as median values
of respiratory rate, appetite, suckling reflex, standing ability and feces
consistency of experimental calves increased significantly during
study (P 0.05). The
results of present study showed that total score of clinical signs in
calves with experimental colisepticemia increased significantly,
although score of some clinical signs such as shock did not change
significantly.
Abstract: Large quantities of solid wastes being generated
worldwide from sources such as household, domestic, industrial,
commercial and construction demolition activities, leads to
environmental concerns. Utilization of these wastes in making
building construction materials can reduce the magnitude of the
associated problems. When these waste products are used in place of
other conventional materials, natural resources and energy are
preserved and expensive and/or potentially harmful waste disposal is
avoided. Recycling which is regarded as the third most preferred waste
disposal option, with its numerous environmental benefits, stand as a
viable option to offset the environmental impact associated with the
construction industry. This paper reviews the results of laboratory tests and important
research findings, and the potential of using these wastes in building
construction materials with focus on sustainable development.
Research gaps, which includes; the need to develop standard mix
design for solid waste based building materials; the need to develop
energy efficient method of processing solid waste use in concrete; the
need to study the actual behavior or performance of such building
materials in practical application and the limited real life application
of such building materials have also been identified. A research is being proposed to develop an environmentally
friendly, lightweight building block from recycled waste paper,
without the use of cement, and with properties suitable for use as
walling unit. This proposed research intends to incorporate,
laboratory experimentation and modeling to address the identified
research gaps.
Abstract: This study evaluated the acute toxicity and tissue
distribution of intravenously administered gold nanoparticles
(AuNPs) in male rabbits. Rabbits were exposed to single dose of
AuNPs (300 μg/ kg). Toxic effects were assessed via general
behavior, hematological parameters, serum biochemical parameters,
and histopathological examination of various rabbits’ organs.
Inductively coupled plasma–mass spectrometry (ICP-MS) was used
to determine gold concentrations in tissue samples collected at
predetermined time intervals. After one week, AuNPs exerted no
obvious acute toxicity in rabbits. However, inflammatory reactions
were observed in liver, lungs and kidneys accompanied with mild
absolute neutrophilia and significant monocytosis. The highest gold
levels were found in the spleen and liver followed by lungs, and
kidneys. These results indicated that AuNPs could be distributed
extensively to various tissues in the body, but primarily in the spleen
and liver.