Abstract: This work presents a numerical model developed to
simulate the dynamics and vibrations of a multistage tractor gearbox.
The effect of time varying mesh stiffness, time varying frictional
torque on the gear teeth, lateral and torsional flexibility of the shafts
and flexibility of the bearings were included in the model. The model
was developed by using the Lagrangian method, and it was applied to
study the effect of three design variables on the vibration and stress
levels on the gears. The first design variable, module, had little effect
on the vibration levels but a higher module resulted to higher bending
stress levels. The second design variable, pressure angle, had little
effect on the vibration levels, but had a strong effect on the stress
levels on the pinion of a high reduction ratio gear pair. A pressure
angle of 25o resulted to lower stress levels for a pinion with 14 teeth
than a pressure angle of 20o. The third design variable, contact ratio,
had a very strong effect on both the vibration levels and bending
stress levels. Increasing the contact ratio to 2.0 reduced both the
vibration levels and bending stress levels significantly. For the gear
train design used in this study, a module of 2.5 and contact ratio of
2.0 for the various meshes was found to yield the best combination
of low vibration levels and low bending stresses. The model can
therefore be used as a tool for obtaining the optimum gear design
parameters for a given multistage spur gear train.
Abstract: In this paper, genetic algorithm (GA) opmization technique is applied to design Flexible AC Transmission System (FACTS)-based damping controllers. Two types of controller structures, namely a proportional-integral (PI) and a lead-lag (LL) are considered. The design problem of the proposed controllers is formulated as an optimization problem and GA is employed to search for optimal controller parameters. By minimizing the time-domain based objective function, in which the deviation in the oscillatory rotor speed of the generator is involved; stability performance of the system is improved. The proposed controllers are tested on a weakly connected power system subjected to different disturbances. The non-linear simulation results are presented to show the effectiveness of the proposed controller and their ability to provide efficient damping of low frequency oscillations. It is also observed that the proposed SSSC-based controllers improve greatly the voltage profile of the system under severe disturbances. Further, the dynamic performances of both the PI and LL structured FACTS-controller are analyzed at different loading conditions and under various disturbance condition as well as under unbalanced fault conditions..
Abstract: The present work deals with thermodynamic analysis
of cascade refrigeration system using ozone friendly refrigerants pair
R507A and R23. R507A is azeotropic mixture composed of HFC
refrigerants R125/R143a (50%/50% wt.). R23 is a single component
HFC refrigerant used as replacement to CFC refrigerant R13 in low
temperature applications. These refrigerants have zero ozone
depletion potential and are non-flammable and as R507A an
azeotropic mixture there is no problem of temperature glide. This
study thermodynamically analyzed R507A-R23 cascade refrigeration
system to optimize the design and operating parameters of the
system. The design and operating parameters include: Condensing,
evaporating, subcooling and superheating temperatures in the high
temperature circuit, temperature difference in the cascade heat
exchanger, Condensing, evaporating, subcooling and superheating
temperatures in the low temperature circuit.
Abstract: Considering the theory of attribute grammars, we use
logical formulas instead of traditional functional semantic rules.
Following the decoration of a derivation tree, a suitable algorithm
should maintain the consistency of the formulas together with the
evaluation of the attributes. This may be a Prolog-like resolution, but
this paper examines a somewhat different strategy, based on
production specialization, local consistency and propagation: given a
derivation tree, it is interactively decorated, i.e. incrementally
checked and evaluated. The non-directed dependencies are
dynamically directed during attribute evaluation.
Abstract: Polymeric microreactors have emerged as a new
generation of carriers that hold tremendous promise in the areas of
cancer therapy, controlled delivery of drugs, for removal of
pollutants etc. Present work reports a simple and convenient
methodology for synthesis of polystyrene and poly caprolactone
microreactors. An aqueous suspension of carboxylated (1μm)
polystyrene latex particles was mixed with toluene solution followed
by freezing with liquid nitrogen. Freezed particles were incubated at
-20°C and characterized for formation of voids on the surface of
polymer microspheres by Field Emission Scanning Electron
Microscope. The hollow particles were then overnight incubated at
40ºC with unfunctionalized quantum dots (QDs) in 5:1 ratio. QDs
Encapsulated polystyrene microcapsules were characterized by
fluorescence microscopy.
Likewise Poly ε-caprolactone microreactors were prepared by
micro-volcanic rupture of freeze dried microspheres synthesized
using emulsification of polymer with aqueous Poly vinyl alcohol and
freezed with liquid nitrogen. Microreactors were examined with Field
Emission Scanning Electron Microscope for size and morphology.
Current study is an attempt to create hollow polymer particles which
can be employed for microencapsulation of nanoparticles and drug
molecules.
Abstract: To achieve reliable solutions, today-s numerical and
experimental activities need developing more accurate methods and
utilizing expensive facilities, respectfully in microchannels. The analytical
study can be considered as an alternative approach to alleviate
the preceding difficulties. Among the analytical solutions, those with
high robustness and low complexities are certainly more attractive.
The perturbation theory has been used by many researchers to analyze
microflows. In present work, a compressible microflow with constant
heat flux boundary condition is analyzed. The flow is assumed to be
fully developed and steady. The Mach and Reynolds numbers are also
assumed to be very small. For this case, the creeping phenomenon
may have some effect on the velocity profile. To achieve robustness
solution it is assumed that the flow is quasi-isothermal. In this study,
the creeping term which appears in the slip boundary condition
is formulated by different mathematical formulas. The difference
between this work and the previous ones is that the creeping term
is taken into account and presented in non-dimensionalized form.
The results obtained from perturbation theory are presented based
on four non-dimensionalized parameters including the Reynolds,
Mach, Prandtl and Brinkman numbers. The axial velocity, normal
velocity and pressure profiles are obtained. Solutions for velocities
and pressure for two cases with different Br numbers are compared
with each other and the results show that the effect of creeping
phenomenon on the velocity profile becomes more important when
Br number is less than O(ε).
Abstract: Group contribution methods such as the UNIFAC are
of major interest to researchers and engineers involved synthesis,
feasibility studies, design and optimization of separation processes as
well as other applications of industrial use. Reliable knowledge of
the phase equilibrium behavior is crucial for the prediction of the fate
of the chemical in the environment and other applications. The
objective of this study was to predict the solubility of selected
volatile organic compounds (VOCs) in glycol polymers and
biodiesel. Measurements can be expensive and time consuming,
hence the need for thermodynamic models. The results obtained in
this study for the infinite dilution activity coefficients compare very
well those published in literature obtained through measurements. It
is suggested that in preliminary design or feasibility studies of
absorption systems for the abatement of volatile organic compounds,
prediction procedures should be implemented while accurate fluid
phase equilibrium data should be obtained from experiment.
Abstract: ZnO+Ga2O3 functionally graded thin films (FGTFs)
were examined for their potential use as Solar cell and organic light
emitting diodes (OLEDs). FGTF transparent conducting oxides (TCO)
were fabricated by combinatorial RF magnetron sputtering. The
composition gradient was controlled up to 10% by changing the
plasma power of the two sputter guns. A Ga2O3+ZnO graded region
was placed on the top layer of ZnO. The FGTFs showed up to 80%
transmittance. Their surface resistances were reduced to < 10% by
increasing the Ga2O3: pure ZnO ratio in the TCO. The FGTFs- work
functions could be controlled within a range of 0.18 eV. The
controlled work function is a very promising technology because it
reduces the contact resistance between the anode and Hall transport
layers of OLED and solar cell devices.
Abstract: In this study, single nozzle method used for
electrospinning technique which composite polymer solution with
cellulose nanowiskers (CNW) was treated by ultrasonic sonificator
have been compared with coaxial (double) nozzle method, in terms of
mechanical, thermal and morphological properties of composite
nanofiber. The effect of water content in composite polymer solution
on properties of nanofiber has also been examined. It has been seen
that single nozzle method which polymer solution does not contain
water has better results than that of coaxial method, in terms of
mechanical, thermal and morphological properties of nanofiber.
However, it is necessary to make an optimization study on setting
condition of ultrasonic treatment to get better dispersion of CNW in
composite nanofiber and to get better mechanical and thermal
properties
Abstract: This study attempts to investigate the relationship
between internal CSR practices and organizational commitment
based on the social exchange theory (SET). Specifically, we examine
the impact of five dimensions of internal CSR practices on
organizational commitment: health and safety, human rights, training
and education, work life balance and workplace diversity. The
proposed model was tested on a sample of 336 frontline employees
within the banking sector in Jordan. Results showed that all internal
CSR dimensions are significantly and positively related to affective
and normative commitment. In addition, the findings of this study
indicate that all internal CSR dimensions did not have a significant
relationship with continuance commitment. Limitations of the study,
directions for future research, and implications of the findings are
discussed.
Abstract: Load managing method on road became necessary
since overloaded vehicles occur damage on road facilities and existing
systems for preventing this damage still show many
problems.Accordingly, efficient managing system for preventing
overloaded vehicles could be organized by using the road itself as a
scale by applying genetic algorithm to analyze the load and the drive
information of vehicles.Therefore, this paper organized Ubiquitous
sensor network system for development of intelligent overload vehicle
regulation system, also in this study, to use the behavior of road, the
transformation was measured by installing underground box type
indoor model and indoor experiment was held using genetic algorithm.
And we examined wireless possibility of overloaded vehicle
regulation system through experiment of the transmission and
reception distance.If this system will apply to road and bridge, might
be effective for economy and convenience through establishment of
U-IT system..
Abstract: Horizontal continuous casting is widely used to
produce semi-finished non-Ferrous products. Homogeneity in the
metallurgical characteristics and mechanical properties for this
product is vital for industrial application. In the present work, the
microstructure and mechanical properties of a horizontal continuous
cast two-phase brass billet have been studied. Impact strength and
hardness variations were examined and the phase composition and
porosity studied with image analysis software. Distinct differences in
mechanical properties were observed between the upper, middle and
lower parts of the billet, which are explained in terms of the
morphology and size of the phase in the microstructure. Hardness
variation in the length of billet is higher in upper area but impact
strength is higher in lower areas.
Abstract: Detecting object in video sequence is a challenging
mission for identifying, tracking moving objects. Background
removal considered as a basic step in detected moving objects tasks.
Dual static cameras placed in front and rear moving platform
gathered information which is used to detect objects. Background
change regarding with speed and direction moving platform, so
moving objects distinguished become complicated. In this paper, we
propose framework allows detection moving object with variety of
speed and direction dynamically. Object detection technique built on
two levels the first level apply background removal and edge
detection to generate moving areas. The second level apply Moving
Areas Filter (MAF) then calculate Correlation Score (CS) for
adjusted moving area. Merging moving areas with closer CS and
marked as moving object. Experiment result is prepared on real scene
acquired by dual static cameras without overlap in sense. Results
showing accuracy in detecting objects compared with optical flow
and Mixture Module Gaussian (MMG), Accurate ratio produced to
measure accurate detection moving object.
Abstract: The effect of streamwise conduction on the thermal
characteristics of forced convection for nanofluidic flow in
rectangular microchannel heat sinks under isothermal wall has been
investigated. By applying the fin approach, models with and without
streamwise conduction term in the energy equation were developed
for hydrodynamically and thermally fully-developed flow. These two
models were solved to obtain closed form analytical solutions for the
nanofluid and solid wall temperature distributions and the analysis
emphasized details of the variations induced by the streamwise
conduction on the nanofluid heat transport characteristics. The effects
of the Peclet number, nanoparticle volume fraction, thermal
conductivity ratio on the thermal characteristics of forced convection
in microchannel heat sinks are analyzed. Due to the anomalous
increase in the effective thermal conductivity of nanofluid compared
to its base fluid, the effect of streamwise conduction is expected to be
more significant. This study reveals the significance of the effect of
streamwise conduction under certain conditions of which the
streamwise conduction should not be neglected in the forced
convective heat transfer analysis of microchannel heat sinks.
Abstract: Recurrence of aneurysm rupture can be attributed to
coil migration and compaction. In order to verify the effects of
hemodynamics on coil compaction and migration, we analyze the
forces and displacements on the coil bundle using a computational
method. Lateral aneurysms partially filled coils are modeled, and
blood flow fields and coil deformations are simulated considering
fluid and solid interaction. Effects of aneurysm neck size and parent
vessel geometry are also investigated. The results showed that coil
deformation was larger in the aneurysms with a wider neck. Parent
vessel geometry and aneurysm neck size also affected mean pressure
force profiles on the coil surface. Pressure forces were higher in wide
neck models with curved parent vessel geometry. Simulation results
showed that coils in the wide neck aneurysm with a curved parent
vessel may be displaced and compacted more easily.
Abstract: The purpose of this research study is to investigate the manner in which various loads affect the mechanical properties of the formed mild steel plates. The investigation focuses on examining the cross-sectional area of the metal plate at the centre of the formed mild steel plate. Six mild steel plates were deformed with different loads. The loads applied on the plates had a magnitude of 5 kg, 10 kg, 15 kg, 20 kg, 25 kg and 30 kg. The radius of the punching die was 120 mm and the loads were applied at room temperature. The investigations established that the applied load causes the Vickers microhardness at the cross-sectional area of the plate to increase due to strain hardening. Hence, the percentage increase of the hardness due to the load was found to be directly proportional to the increase in the load. Furthermore, the tensile test results for the parent material showed that the average Ultimate Tensile Strength (UTS) for the three samples was 308 MPa while the average Yield Strength and Percentage Elongation were 227 MPa and 38 % respectively. Similarly, the UTS of the formed components increased after the deformation of the plate, as such it can be concluded that the forming loads alter the mechanical properties of the materials by improving and strengthening the material properties.
Abstract: Chitosan is a biopolymer composed of glucosamine
and N-acetyl glucosamine. Solubility and viscosity pose problems in
some applications. These problems can be overcome with unique
modifications. In this study, firstly, chitosan was modified by caffeic
acid and thioglycolic acid, separately. Then, growing effects of these
modified polymers was observed in U937 cell line. Caffeic acid is a
phenolic compound and its modifications act carcinogenic inhibitors
in drugs. Thiolated chitosans are commonly being used for drugdelivery
systems in various routes, because of enhancing
mucoadhesiveness property. U937 cell line was used model cell for
leukaemia. Modifications were achieved by 1 – 15 % binding range.
Increasing binding ratios showed higher radical-scavenging activity
and reducing cell growth, in compared to native chitosan. Caffeic
acid modifications showed higher radical-scavenging activity than
thiolated chitosans at the same concentrations. Caffeic acid and
thioglycolic acid modifications inhibited growth of U937, effectively.
Abstract: The aim of the present investigation was to compare
sex differences in thyroid gland structure of rabbits. Five adult male
and five adult female (3.1-3.5 kg body weight) New Zealand white
rabbits were used in the experiment. Results showed that at light
microscopic level, there was no sex difference in microscopic
appearance of the thyroid glands. At electron microscopic level,
however, the mitochondria and the microvilli of the follicular cells
are more numerous and the Golgi complex is also more extensive in
male rabbits in comparison to females. Results obtained from
micrometric measurements showed that the volume density of the
follicles is higher in males than in females, but the differences are not
statistically significant .The volume density of epithelium and the
height of follicular cells are significantly greater in males than in
females and reverse is true about the volume density of interstitium
(p
Abstract: In recent years, the underground water sources in
southern Taiwan have become salinized because of saltwater
intrusions. This study explores the adsorption characteristics of
activated carbon on salinizing inorganic salts using isothermal
adsorption experiments and provides a model analysis. The
temperature range for the isothermal adsorption experiments ranged
between 5 to 45 ℃, and the amount adsorbed varied between 28.21 to
33.87 mg/g. All experimental data of adsorption can be fitted to both
the Langmuir and the Freundlich models. The thermodynamic
parameters for per chlorate onto granular activated carbon were
calculated as -0.99 to -1.11 kcal/mol for DG°, -0.6 kcal/mol for DH°,
and 1.21 to 1.84 kcal/mol for DS°. This shows that the adsorption
process of granular activated carbon is spontaneously exothermic. The
observation of adsorption behaviors under low ionic strength, low pH
values, and low temperatures is beneficial to the adsorption removal of
perchlorate with granular activated carbon.
Abstract: Modern Society is strongly dependent on a reliable
power supply. The availability of cheap and reliable supply of
electrical energy is an indicator of societal welfare. Uninterrupted
reliable operation of a modern power system depends to a great
extent on reliable and satisfactory performance of insulators under
different environmental conditions. This paper reports result of
natural pollution tests that have been done at sites around city of
Aligarh (India). Flashover voltage per insulation distance (FOVUID)
of porcelain disc insulator for different pH values, ESDD has been
recorded for proper correlation between electrical and chemical
parameters. The pH of the contaminants has been suggested to be an
effective pollution severity indicator and may be used as a diagnostic
parameter for proper maintenance of porcelain insulators.