Abstract: Recent progress in calculation of the one-loop selfenergy
of the electron bound in the Coulomb field is summarized.
The relativistic multipole expansion is introduced. This expansion
is based on a single assumption: except for the part of the time
component of the electron four-momentum corresponding to the
electron rest mass, the exchange of four-momentum between the
virtual electron and photon can be treated perturbatively. For non Sstates
and normalized difference n3En −E1 of the S-states this
itself yields very accurate results after taking the method to the third
order. For the ground state the perturbation treatment of the electron
virtual states with very high three-momentum is to be avoided. For
these states one can always rearrange the pertinent expression in such
a way that free-particle approximation is allowed. Combination of
the relativistic multipole expansion and free-particle approximation
yields very accurate result after taking the method to the ninth order.
These results are in very good agreement with the previous results
obtained by the partial wave expansion and definitely exclude the
possibility that the uncertainity in determination of the proton radius
comes from the uncertainity in the calculation of the one-loop selfenergy.
Abstract: This paper presents the determination of the proper
quality costs parameters which provide the optimum return. The
system dynamics simulation was applied. The simulation model was
constructed by the real data from a case of the electronic devices
manufacturer in Thailand. The Steepest Descent algorithm was
employed to optimise. The experimental results show that the
company should spend on prevention and appraisal activities for 850
and 10 Baht/day respectively. It provides minimum cumulative total
quality cost, which is 258,000 Baht in twelve months. The effect of
the step size in the stage of improving the variables to the optimum
was also investigated. It can be stated that the smaller step size
provided a better result with more experimental runs. However, the
different yield in this case is not significant in practice. Therefore, the
greater step size is recommended because the region of optima could
be reached more easily and rapidly.
Abstract: The risk of water erosion is one of the main
environmental concerns in the southern Mediterranean regions. Thus,
quantification of soil loss is an important issue for soil and water
conservation managers. The objective of this paper is to examine the
applicability of the Soil and Water Assessment Tool (SWAT) model
in The Sarrath river catchment, North of Tunisia, and to identify the
most vulnerable areas in order to help manager implement an
effective management program. The spatial analysis of the results
shows that 7 % of the catchment experiences very high erosion risk,
in need for suitable conservation measures to be adopted on a priority
basis. The spatial distribution of erosion risk classes estimated 3%
high, 5,4% tolerable, and 84,6% low. Among the 27 delineated subcatchments
only 4 sub-catchments are found to be under high and
very high soil loss group, two sub-catchments fell under moderate
soil loss group, whereas other sub-catchments are under low soil loss
group.
Abstract: The present work deals with the calculation of
transport properties of Hg0.8Cd0.2Te (MCT) semiconductor in
degenerate case. Due to their energy-band structure, this material
becomes degenerate at moderate doping densities, which are around
1015 cm-3, so that the usual Maxwell-Boltzmann approximation is
inaccurate in the determination of transport parameters. This problem
is faced by using Fermi-Dirac (F-D) statistics, and the non-parabolic
behavior of the bands may be approximated by the Kane model. The
Monte Carlo (MC) simulation is used here to determinate transport
parameters: drift velocity, mean energy and drift mobility versus
electric field and the doped densities. The obtained results are in
good agreement with those extracted from literature.
Abstract: Imaging is defined as the process of obtaining
geometric images either two dimensional or three dimensional by scanning or digitizing the existing objects or products. In this research, it applied to retrieve 3D information of the human skin
surface in medical application. This research focuses on analyzing
and determining volume of leg ulcers using imaging devices. Volume
determination is one of the important criteria in clinical assessment of leg ulcer. The volume and size of the leg ulcer wound will give the
indication on responding to treatment whether healing or worsening.
Different imaging techniques are expected to give different result (and accuracies) in generating data and images. Midpoint projection
algorithm was used to reconstruct the cavity to solid model and compute the volume. Misinterpretation of the results can affect the
treatment efficacy. The objectives of this paper is to compare the
accuracy between two 3D data acquisition method, which is laser
triangulation and structured light methods, It was shown that using models with known volume, that structured-light-based 3D technique
produces better accuracy compared with laser triangulation data
acquisition method for leg ulcer volume determination.
Abstract: The cardiovascular system has become the most
important subject of clinical research, particularly measurement of
arterial blood flow. Therefore correct determination of arterial
diameter is crucial. We propose a novel, semi-automatic method for
artery lumen detection. The method is based on Gaussian probability
function. Usability of our proposed method was assessed by
analyzing ultrasound B-mode CFA video sequences acquired from
eleven healthy volunteers. The correlation coefficient between the
manual and semi-automatic measurement of arterial diameter was
0.996. Our proposed method for detecting artery boundary is novel
and accurate enough for the measurement of artery diameter.
Abstract: A lot of research made during these last 15 years
showed that the quantification of the springback has a significant role
in the industry of sheet metal forming. These studies were made with
the objective of finding techniques and methods to minimize or
completely avoid this permanent physical variation. Moreover, the
use of steel and aluminum alloys in the car industry and aviation
poses every day the problem of the springback. The determination in
advance of the quantity of the springback allows consequently the
design and manufacture of the tool. The aim of this paper is to study
experimentally the influence of the blank holder force BHF and the
radius of curvature of the die on the springback and their influence on
the strain in various zone of specimen.
The original of our purpose consist on tests which are ensured by
adapting a U-type stretching-bending device on a tensile testing
machine, where we studied and quantified the variation of the
springback according to displacement.
Abstract: This paper analyses the torsional efforts in gas turbine-generator shafts caused by high speed automatic reclosing of transmission lines. This issue is especially important for cases of three phase short circuit and unsuccessful reclosure of lines in the vicinity of the thermal plant. The analysis was carried out for the thermal plant TERMOPERNAMBUCO located on Northeast region of Brazil. It is shown that stress level caused by lines unsuccessful reclosing can be several times higher than terminal three-phase short circuit. Simulations were carried out with detailed shaft torsional model provided by machine manufacturer and with the “Alternative Transient Program – ATP" program [1]. Unsuccessful three phase reclosing for selected lines in the area closed to the plant indicated most critical cases. Also, reclosing first the terminal next to the gas turbine gererator will lead also to the most critical condition. Considering that the values of transient torques are very sensible to the instant of reclosing, simulation of unsuccessful reclosing with statistics ATP switch were carried out for determination of most critical transient torques for each section of the generator turbine shaft.
Abstract: Highly pathogenic avian influenza (HPAI) H5N1 viruses have created demand for a cost-effective vaccine to prevent a pandemic of the disease. Here, we report that Trichoplusia ni (T. ni) larvae can act as a cost-effective bioreactor to produce recombinant HA5 (rH5HA) proteins as an potential effective vaccine for chickens. To facilitate the recombinant virus identification, virus titer determination and access the infected larvae, we employed the internal ribosome entry site (IRES) derived from Perina nuda virus (PnV, belongs to insect picorna like Iflavirus genus) to construct a bi-cistronic baculovirus expression vector that can express the rH5HA protein and enhanced green fluorescent protein (EGFP) simultaneously. Western blot analysis revealed that the 70 kDa rH5HA protein and partially cleaved products (40 kDa H5HA1) were generated in T. ni larvae infected with recombinant baculovirus carrying the H5HA gene. These data suggest that the baculovirus-larvae recombinant protein expression system could be a cost-effective platform for H5N1 vaccine production.
Abstract: Training with Functional Electrical Stimulation (FES)
has both physiological and psychological benefits for spinal cord
injured subjects. Commonly used methods for quantification of
spasticity have shown controversial reliability. In this study we
propose a method for quick determination of spasticity in spinal cord
injured subjects on a cycling and measurement system. 23 patients
did training sessions on an instrumented mobile FES cycle three
times a week over two months as part of their clinical rehabilitation
program. Spasticity (MAS) and the legs resistance to the pedaling
motion were assessed before and after the FES training and
measurements were done on the subjects ability to pedal with our
without motor assistance. Measurements with test persons with
incomplete spastic paraplegia have shown that spasticity is decreased
after a 30 min cycling training with functional electrical stimulation
(FES).
Abstract: The current practice of determination of moisture diffusivity of building materials under laboratory conditions is predominantly aimed at the absorption phase. The main reason is the simplicity of the inverse analysis of measured moisture profiles. However, the liquid moisture transport may exhibit significant hysteresis. Thus, the moisture diffusivity should be different in the absorption (wetting) and desorption (drying) phase. In order to bring computer simulations of hygrothermal performance of building materials closer to the reality, it is then necessary to find new methods for inverse analysis which could be used in the desorption phase as well. In this paper we present genetic algorithm as a possible method of solution of the inverse problem of moisture transport in desorption phase. Its application is demonstrated for AAC as a typical building material.
Abstract: A power cable is widely used for power supply in
power distributing networks and power transmission lines. Due to
limitations in the production, delivery and setting up power cables,
they are produced and delivered in several separate lengths. Cable
itself, consists of two cable terminations and arbitrary number of
cable joints, depending on the cable route length. Electrical stress
control is needed to prevent a dielectric breakdown at the end of the
insulation shield in both the air and cable insulation. Reliability of
cable joint depends on its materials, design, installation and operating
environment. The paper describes design and performance results for
new modeled cable joints. Design concepts, based on numerical
calculations, must be correct. An Equivalent Electrodes
Method/Boundary Elements Method-hybrid approach that allows
electromagnetic field calculations in multilayer dielectric media,
including inhomogeneous regions, is presented.
Abstract: Autoregressive Moving average (ARMA) is a parametric based method of signal representation. It is suitable for problems in which the signal can be modeled by explicit known source functions with a few adjustable parameters. Various methods have been suggested for the coefficients determination among which are Prony, Pade, Autocorrelation, Covariance and most recently, the use of Artificial Neural Network technique. In this paper, the method of using Artificial Neural network (ANN) technique is compared with some known and widely acceptable techniques. The comparisons is entirely based on the value of the coefficients obtained. Result obtained shows that the use of ANN also gives accurate in computing the coefficients of an ARMA system.
Abstract: Psoriasis is a widespread skin disease affecting up to 2% population with plaque psoriasis accounting to about 80%. It can be identified as a red lesion and for the higher severity the lesion is usually covered with rough scale. Psoriasis Area Severity Index (PASI) scoring is the gold standard method for measuring psoriasis severity. Scaliness is one of PASI parameter that needs to be quantified in PASI scoring. Surface roughness of lesion can be used as a scaliness feature, since existing scale on lesion surface makes the lesion rougher. The dermatologist usually assesses the severity through their tactile sense, therefore direct contact between doctor and patient is required. The problem is the doctor may not assess the lesion objectively. In this paper, a digital image analysis technique is developed to objectively determine the scaliness of the psoriasis lesion and provide the PASI scaliness score. Psoriasis lesion is modelled by a rough surface. The rough surface is created by superimposing a smooth average (curve) surface with a triangular waveform. For roughness determination, a polynomial surface fitting is used to estimate average surface followed by a subtraction between rough and average surface to give elevation surface (surface deviations). Roughness index is calculated by using average roughness equation to the height map matrix. The roughness algorithm has been tested to 444 lesion models. From roughness validation result, only 6 models can not be accepted (percentage error is greater than 10%). These errors occur due the scanned image quality. Roughness algorithm is validated for roughness measurement on abrasive papers at flat surface. The Pearson-s correlation coefficient of grade value (G) of abrasive paper and Ra is -0.9488, its shows there is a strong relation between G and Ra. The algorithm needs to be improved by surface filtering, especially to overcome a problem with noisy data.
Abstract: Many studies have been conducted for derivation of
attenuation relationships worldwide, however few relationships have
been developed to use for the seismic region of Iranian plateau and
only few of these studies have been conducted for derivation of
attenuation relationships for parameters such as uniform duration.
Uniform duration is the total time during which the acceleration is
larger than a given threshold value (default is 5% of PGA). In this
study, the database was same as that used previously by Ghodrati
Amiri et al. (2007) with same correction methods for earthquake
records in Iran. However in this study, records from earthquakes with
MS< 4.0 were excluded from this database, each record has
individually filtered afterward, and therefore the dataset has been
expanded. These new set of attenuation relationships for Iran are
derived based on tectonic conditions with soil classification into rock
and soil. Earthquake parameters were chosen to be
hypocentral distance and magnitude in order to make it easier to use
the relationships for seismic hazard analysis. Tehran is the capital
city of Iran wit ha large number of important structures. In this study,
a probabilistic approach has been utilized for seismic hazard
assessment of this city. The resulting uniform duration against return
period diagrams are suggested to be used in any projects in the area.
Abstract: The purpose of this investigation is to relate the rain
power and the overland flow power to soil erodibility to assess the
effects of both parameters on soil erosion using variable rainfall
intensity on remoulded agricultural soil. Six rainfall intensities were
used to simulate the natural rainfall and are as follows: 12.4mm/h,
20.3mm/h, 28.6mm/h, 52mm/h, 73.5mm/h and 103mm/h. The results
have shown that the relationship between overland flow power and
rain power is best represented by a linear function (R2=0.99). As
regards the relationships between soil erodibility factor and rain and
overland flow powers, the evolution of both parameters with the
erodibility factor follow a polynomial function with high coefficient
of determination. From their coefficients of determination (R2=0.95)
for rain power and (R2=0.96) for overland flow power, we can
conclude that the flow has more power to detach particles than rain.
This could be explained by the fact that the presence of particles,
already detached by rain and transported by the flow, give the flow
more weight and then contribute to the detachment of particles by
collision.
Abstract: The Želazny Most tailing pond is one of the largest
facilities worldwide for waste disposal from the copper mines located
in South-West Poland. A potential failure of the dam would allow
more than 10 million cubic meters of contaminated slurry to flow to
the valley, causing immense environmental problems to the
surrounding area. Thus, the determination of the strength properties
of the dam's soils and their variability is of utmost importance.
An extensive site investigation consisting of more than 480 cone
penetration tests (CPTs) with or without pore water pressure
measurements were conducted within a period of 13 years to study
the mechanical properties of the tailings body. The present work
investigates the point variability of the soil strength parameters
(effective friction angle
Abstract: In textile industry, besides the conventional textile
products, technical textile goods, that have been brought external
functional properties into, are being developed for technical textile
industry. Especially these products produced with weaving
technology are widely preferred in areas such as sports, geology,
medical, automotive, construction and marine sectors. These textile
products are exposed to various stresses and large deformations under
typical conditions of use. At this point, sufficient and reliable data
could not be obtained with uniaxial tensile tests for determination of
the mechanical properties of such products due to mainly biaxial
stress state. Therefore, the most preferred method is a biaxial tensile
test method and analysis. These tests and analysis is applied to fabrics
with different functional features in order to establish the textile
material with several characteristics and mechanical properties of the
product. Planar biaxial tensile test, cylindrical inflation and bulge
tests are generally required to apply for textile products that are used
in automotive, sailing and sports areas and construction industry to
minimize accidents as long as their service life. Airbags, seat belts
and car tires in the automotive sector are also subject to the same
biaxial stress states, and can be characterized by same types of
experiments. In this study, in accordance with the research literature
related to the various biaxial test methods are compared. Results with
discussions are elaborated mainly focusing on the design of a biaxial
test apparatus to obtain applicable experimental data for developing a
finite element model. Sample experimental results on a prototype
system are expressed.
Abstract: The present work describes an experimental
investigation concerning the determination of viscosity behavior with
shear rate and temperature of edible oils: canola; sunflower; corn;
soybean and the no edible oil: Jatropha curcas. Besides these, it was
tested a blend of canola, corn and sunflower oils as well as sunflower
and soybean biodiesel. Based on experiments, it was obtained shear
stress and viscosity at different shear rates of each sample at 40ºC, as
well as viscosity of each sample at various temperatures in the range
of 24 to 85ºC. Furthermore, it was compared the curves obtained for
the viscosity versus temperature with the curves obtained by
modeling the viscosity dependency on temperature using the Vogel
equation. Also a test in a stationary engine was performed in order to
study the energy generation using blends of soybean oil and soybean
biodiesel with diesel.
Abstract: From a long time age, human beings have chosen their
place of residence and comfort so that those places would have
relatively ideal natural and climatic conditions. For this reason, from
the beginning, the civilizations have been formed in the susceptible
natural regions such as Mesopotamia in Iran and Nile coasts in
Egypt. Also, the core of human density has been made in the form of
an oasis in the deserts.
Regarding the formation and combination of the native
architecture in different regions of Iran, we find that different
properties of these climates have affected frequently the formation of
cities and the architectural combinations of these regions. Thus, the
precise determinations of climatic areas and attaining the climatic
properties of different regions have a great deal of importance in
presenting appropriate and compatible-with-climate designs.