Abstract: The objective of this research was to study factors,
which were affected on surface roughness in high speed milling of
hardened tool steel. Material used in the experiment was tool steel JIS
SKD 61 that hardened on 60 ±2 HRC. Full factorial experimental
design was conducted on 3 factors and 3 levels (3
3
designs) with 2
replications. Factors were consisted of cutting speed, feed rate, and
depth of cut. The results showed that influenced factor affected to
surface roughness was cutting speed, feed rate and depth of cut which
showed statistical significant. Higher cutting speed would cause on
better surface quality. On the other hand, higher feed rate would cause
on poorer surface quality. Interaction of factor was found that cutting
speed and depth of cut were significantly to surface quality. The
interaction of high cutting speed associated with low depth of cut
affected to better surface quality than low cutting speed and high depth
of cut.
Abstract: Previous the 3D model texture generation from multi-view images and mapping algorithms has issues in the texture chart generation which are the self-intersection and the concentration of the texture in texture space. Also we may suffer from some problems due to the occluded areas, such as inside parts of thighs. In this paper we propose a texture mapping technique for 3D models using multi-view images on the GPU. We do texture mapping directly on the GPU fragment shader per pixel without generation of the texture map. And we solve for the occluded area using the 3D model depth information. Our method needs more calculation on the GPU than previous works, but it has shown real-time performance and previously mentioned problems do not occur.
Abstract: Machining through turning was carried out in a lathe
to study the chip formation of Multiphase Ferrite
(F-B-M) microalloyed steel. Taguchi orthogonal array was employed
to perform the machining. Continuous and discontinuous chips were
formed for different cutting parameters like speed, feed and depth of
cut. Optical and scanning electron microscope was employed to
identify the chip morphology.
Abstract: Hopfield model of associative memory is studied in this work. In particular, two main problems that it possesses: the apparition of spurious patterns in the learning phase, implying the well-known effect of storing the opposite pattern, and the problem of its reduced capacity, meaning that it is not possible to store a great amount of patterns without increasing the error probability in the retrieving phase. In this paper, a method to avoid spurious patterns is presented and studied, and an explanation of the previously mentioned effect is given. Another technique to increase the capacity of a network is proposed here, based on the idea of using several reference points when storing patterns. It is studied in depth, and an explicit formula for the capacity of the network with this technique is provided.
Abstract: The aim of this research is to evaluate surface
roughness and develop a multiple regression model for surface roughness as a function of cutting parameters during the turning of
flame hardened medium carbon steel with TiN-Al2O3-TiCN coated inserts. An experimental plan of work and signal-to-noise ratio (S/N)
were used to relate the influence of turning parameters to the
workpiece surface finish utilizing Taguchi methodology. The effects
of turning parameters were studied by using the analysis of variance (ANOVA) method. Evaluated parameters were feed, cutting speed,
and depth of cut. It was found that the most significant interaction among the considered turning parameters was between depth of cut and feed. The average surface roughness (Ra) resulted by TiN-Al2O3-
TiCN coated inserts was about 2.44 μm and minimum value was 0.74 μm. In addition, the regression model was able to predict values for surface roughness in comparison with experimental values within
reasonable limit.
Abstract: the current study presents a modeling framework to determine the torsion strength of an induction hardened splined shaft by considering geometry and material aspects with the aim to optimize the static torsion strength by selection of spline geometry and hardness depth. Six different spline geometries and seven different hardness profiles including non-hardened and throughhardened shafts have been considered. The results reveal that the torque that causes initial yielding of the induction hardened splined shaft is strongly dependent on the hardness depth and the geometry of the spline teeth. Guidelines for selection of the appropriate hardness depth and spline geometry are given such that an optimum static torsion strength of the component can be achieved.
Abstract: Research results and optimal parameters investigation
of laser cut and profiling of diamond and quartz substrates by
femtosecond laser pulses are presented. Profiles 10 μm in width, ~25
μm in depth and several millimeters long were made. Investigation of
boundaries quality has been carried out with the use of AFM
«Vecco». Possibility of technological formation of profiles and
micro-holes in diamond and quartz substrates with nanometer-scale
boundaries is shown. Experimental results of multilayer dielectric
cover treatment are also presented. Possibility of precise upper layer
(thickness of 70–140 nm) removal is demonstrated. Processes of thin
metal film (60 nm and 350 nm thick) treatment are considered.
Isolation tracks (conductance ~ 10-11 S) 1.6–2.5 μm in width in
conductive metal layers are formed.
Abstract: The objectives of this research paper were to study the
influencing factors that contributed to the success of electronic
commerce (e-commerce) and to study the approach to enhance the
standard of e-commerce for small and medium enterprises (SME).
The research paper focused the study on only sole proprietorship
SMEs in Bangkok, Thailand. The factors contributed to the success
of SME included business management, learning in the organization,
business collaboration, and the quality of website. A quantitative and
qualitative mixed research methodology was used. In terms of
quantitative method, a questionnaire was used to collect data from
251 sole proprietorships. The System Equation Model (SEM) was
utilized as the tool for data analysis. In terms of qualitative method,
an in-depth interview, a dialogue with experts in the field of ecommerce
for SMEs, and content analysis were used.
By using the adjusted causal relationship structure model, it was
revealed that the factors affecting the success of e-commerce for
SMEs were found to be congruent with the empirical data. The
hypothesis testing indicated that business management influenced the
learning in the organization, the learning in the organization
influenced business collaboration and the quality of the website, and
these factors, in turn, influenced the success of SMEs. Moreover, the
approach to enhance the standard of SMEs revealed that the majority
of respondents wanted to enhance the standard of SMEs to a high
level in the category of safety of e-commerce system, basic structure
of e-commerce, development of staff potentials, assistance of budget
and tax reduction, and law improvement regarding the e-commerce
respectively.
Abstract: The quantitative determination of several trace
elements (Cr, As, Se, Cd, Hg, Pb) existing as inorganic impurities in
some oriental herb-products such as Lingzhi Mushroom capsules,
Philamin powder, etc using ICP-MS has been studied. Various
instrumental parameters such as power, gas flow rate, sample depth, as
well as the concentration of nitric acid and thick background due to
high concentration of possible interferences on the determination of
these above-mentioned elements was investigated and the optimum
working conditions of the sample measurement on ICP-MS
(Agilent-7500a) were reported. Appropriate isotope internal standards
were also used to improve the accuracy of mercury determination.
Optimal parameters for sampling digestion were also investigated. The
recovery of analytical procedure was examined by using a Certified
Reference Material (IAEA-CRM 359). The recommended procedure
was then applied for the quantitative determination of Cr, As, Se, Cd,
Hg, Pb in Lingzhi Mushroom capsule, and Philamine powder samples.
The reproducibility of sample measurement (average value between
94 and 102%) and the uncertainty of analytical data (less than 20%)
are acceptable.
Abstract: End milling process is one of the common metal
cutting operations used for machining parts in manufacturing
industry. It is usually performed at the final stage in manufacturing a
product and surface roughness of the produced job plays an
important role. In general, the surface roughness affects wear
resistance, ductility, tensile, fatigue strength, etc., for machined parts
and cannot be neglected in design. In the present work an
experimental investigation of end milling of aluminium alloy with
carbide tool is carried out and the effect of different cutting
parameters on the response are studied with three-dimensional
surface plots. An artificial neural network (ANN) is used to establish
the relationship between the surface roughness and the input cutting
parameters (i.e., spindle speed, feed, and depth of cut). The Matlab
ANN toolbox works on feed forward back propagation algorithm is
used for modeling purpose. 3-12-1 network structure having
minimum average prediction error found as best network architecture
for predicting surface roughness value. The network predicts surface
roughness for unseen data and found that the result/prediction is
better. For desired surface finish of the component to be produced
there are many different combination of cutting parameters are
available. The optimum cutting parameter for obtaining desired
surface finish, to maximize tool life is predicted. The methodology is
demonstrated, number of problems are solved and algorithm is coded
in Matlab®.
Abstract: This study was aimed to explain the influence of surface roughness of the drawbead on non-symmetry deep drawing cold rolled steel sheet to improve the drawability of cold rolled steel sheet. The variables used in this study included semi-circle drawbead with 3 levels of surface roughness which are 6.127 mm Ra, 0.963 mm Ra and 0.152 mm Ra and cold rolled steel sheet according to 3 grades of the JIS standards which are SPCC, SPCE and SPCD with the thickness of 1.0 mm and the blankholder force which is 50% of the drawing force and the depth of 50 mm. According to the test results, when there was the increase in the surface roughness of drawbead, there would be the increase in deep drawing force, especially the SPCC cold rolled steel sheet. This is similar to the increase in the equivalent strain and the wall thickness distribution when the surface roughness of the drawbead increased. It could be concluded that the surface roughness of drawbead has an influence on deep drawing cold rolled steel sheet, especially the drawing force, the equivalent strain and the wall thickness distribution.
Abstract: Many applications require surface modification and
micro-structuring of polymers. For these purposes is mainly used
ultraviolet (UV) radiation from excimer lamps or excimer lasers.
However, these sources have a decided disadvantage - degrading the
polymer deep inside due to relatively big radiation penetration depth
which may exceed 100 μm. In contrast, extreme ultraviolet (EUV)
radiation is absorbed in a layer approximately 100 nm thick only. In
this work, the radiation from a discharge-plasma EUV source (with
wavelength 46.9 nm) based on a capillary discharge driver is focused
with a spherical Si/Sc multilayer mirror for surface modification of
PMMA sample or thin gold layer (thickness about 40 nm). It was
found that the focused EUV laser beam is capable by one shot to
ablate PMMA or layer of gold, even if the focus is significantly
influenced by astigmatism.
Abstract: The storage of chemical fertilizers in concrete building often leads to durability problems due to chemical attack. The damage of concrete is mostly caused by certain ammonium salts. The main purpose of the research is to investigate the durability properties of concrete being exposed to ammonium nitrate solution. In this investigation, experiments are conducted on concrete type G50 and G60. The leaching process is achieved by the use of 20% concentration solution of ammonium nitrate. The durability properties investigated are water absorption, volume of permeable voids, and sorptivity. Compressive strength, pH value, and degradation depth are measured after a certain period of leaching. A decrease in compressive strength and an increase in porosity are found through the conducted experiments. Apart from that, the experimental data shows that pH value decreases with increased leaching time while the degradation depth of concrete increases with leaching time. By comparing concrete type G50 and G60, concrete type G60 is more resistant to ammonium nitrate attack.
Abstract: An effective approach for realizing the binary tree structure, representing a combinational logic functionality with enhanced throughput, is discussed in this paper. The optimization in maximum operating frequency was achieved through delay minimization, which in turn was possible by means of reducing the depth of the binary network. The proposed synthesis methodology has been validated by experimentation with FPGA as the target technology. Though our proposal is technology independent, yet the heuristic enables better optimization in throughput even after technology mapping for such Boolean functionality; whose reduced CNF form is associated with a lesser literal cost than its reduced DNF form at the Boolean equation level. For cases otherwise, our method converges to similar results as that of [12]. The practical results obtained for a variety of case studies demonstrate an improvement in the maximum throughput rate for Spartan IIE (XC2S50E-7FT256) and Spartan 3 (XC3S50-4PQ144) FPGA logic families by 10.49% and 13.68% respectively. With respect to the LUTs and IOBUFs required for physical implementation of the requisite non-regenerative logic functionality, the proposed method enabled savings to the tune of 44.35% and 44.67% respectively, over the existing efficient method available in literature [12].
Abstract: Multi criteria decision analysis (MDCA) covers both
data and experience. It is very common to solve the problems with
many parameters and uncertainties. GIS supported solutions improve
and speed up the decision process. Weighted grading as a MDCA
method is employed for solving the geotechnical problems. In this
study, geotechnical parameters namely soil type; SPT (N) blow
number, shear wave velocity (Vs) and depth of underground water
level (DUWL) have been engaged in MDCA and GIS. In terms of
geotechnical aspects, the settlement suitability of the municipal area
was analyzed by the method. MDCA results were compatible with
the geotechnical observations and experience. The method can be
employed in geotechnical oriented microzoning studies if the criteria
are well evaluated.
Abstract: Subdivision surfaces were applied to the entire
meshes in order to produce smooth surfaces refinement from coarse
mesh. Several schemes had been introduced in this area to provide a
set of rules to converge smooth surfaces. However, to compute and
render all the vertices are really inconvenient in terms of memory
consumption and runtime during the subdivision process. It will lead
to a heavy computational load especially at a higher level of
subdivision. Adaptive subdivision is a method that subdivides only at
certain areas of the meshes while the rest were maintained less
polygons. Although adaptive subdivision occurs at the selected areas,
the quality of produced surfaces which is their smoothness can be
preserved similar as well as regular subdivision. Nevertheless,
adaptive subdivision process burdened from two causes; calculations
need to be done to define areas that are required to be subdivided and
to remove cracks created from the subdivision depth difference
between the selected and unselected areas. Unfortunately, the result
of adaptive subdivision when it reaches to the higher level of
subdivision, it still brings the problem with memory consumption.
This research brings to iterative process of adaptive subdivision to
improve the previous adaptive method that will reduce memory
consumption applied on triangular mesh. The result of this iterative
process was acceptable better in memory and appearance in order to
produce fewer polygons while it preserves smooth surfaces.
Abstract: An algorithm for estimating the disparity of objects of
interest is proposed. This algorithm uses image shifting and
overlapping area to estimate the disparity value; thereby depth of the
objects of interest can be obtained. The algorithm is able to perform
at different levels of accuracy. However, as the accuracy increases
the processing speed decreases. The algorithm is tested with static
stereo images and sequence of stereo images. The experimental
results are presented in this paper.
Abstract: Titanium alloys like the modern alloy Ti 6Al 2Sn 4Zr 6Mo (Ti-6246) combine excellent specific mechanical properties and corrosion resistance. On the other hand,due to their material characteristics, machining of these alloys is difficult to perform. The aim of the current study is the analyses of wear mechanisms of coated cemented carbide tools applied in orthogonal cutting experiments of Ti-6246 alloy. Round bars were machined with standard coated tools in dry conditions on a CNC latheusing a wide range of cutting speeds and cutting depths. Tool wear mechanisms were afterwards investigated by means of stereo microscopy, optical microscopy, confocal microscopy and scanning electron microscopy. Wear mechanisms included fracture of the tool tip (total failure) and abrasion. Specific wear features like crater wear, micro cracks and built-up edgeformation appeared depending of the mechanical and thermal conditions generated in the workpiece surface by the cutting action.
Abstract: The stab resistance performance of newly developed
fabric composites composed of hexagonal paper honeycombs, filled
with shear thickening fluid (STF), and woven Kevlar® fabric or
UHMPE was investigated in this study. The STF was prepared by
dispersing submicron SiO2 particles into polyethylene glycol (PEG).
Our results indicate that the STF-Kevlar composite possessed lower
penetration depth than that of neat Kevlar. In other words, the
STF-Kevlar composite can attain the same energy level in
stab-resistance test with fewer layers of Kevlar fabrics than that of the
neat Kevlar fabrics. It also indicates that STF can be used for the
fabrication of flexible body armors and can provide improved
protection against stab threats. We found that the stab resistance of the
STF-Kevlar composite increases with the increase of SiO2
concentration in STF. Moreover, the silica particles functionalized
with silane coupling agent can further improve the stab resistance.
Abstract: The paper presents the influence of the conventional
ploughing tillage technology in comparison with the minimum
tillage, upon the soil properties, weed control and yield in the case of
maize (Zea mays L.), soya-bean (Glycine hispida L.) and winter
wheat (Triticum aestivum L.) in a three years crop rotation. A
research has been conducted at the University of Agricultural
Sciences and Veterinary Medicine Cluj-Napoca, Romania. The use of
minimum soil tillage systems within a three years rotation: maize,
soya-bean, wheat favorites the rise of the aggregates hydro stability
with 5.6-7.5% on a 0-20 cm depth and 5-11% on 20-30 cm depth.
The minimum soil tillage systems – paraplow, chisel or rotary grape
– are polyvalent alternatives for basic preparation, germination bed
preparation and sowing, for fields and crops with moderate loose
requirements being optimized technologies for: soil natural fertility
activation and rationalization, reduction of erosion, increasing the
accumulation capacity for water and realization of sowing in the
optimal period. The soil tillage system influences the productivity
elements of cultivated species and finally the productions thus
obtained. Thus, related to conventional working system, the
productions registered in minimum tillage working represented 89-
97% in maize, 103-112% in soya-bean, 93-99% in winter-wheat. The
results of investigations showed that the yield is a conclusion soil
tillage systems influence on soil properties, plant density assurance
and on weed control. Under minimum tillage systems in the case of
winter weat as an option for replacing classic ploughing, the best
results in terms of quality indices were obtained from version worked
with paraplow, followed by rotary harrow and chisel. At variants
worked with paraplow were obtained quality indices close to those of
the variant worked with plow, and protein and gluten content was
even higher. At Ariesan variety, highest protein content, 12.50% and
gluten, 28.6% was obtained for the variant paraplow.