Abstract: The behavior of three phase five leg transformer under voltage sag is studied in this paper. This paper proposes a simple, practical model of a three phase-five leg, saturated transformer with accurate performance. Transformer saturation is produced when the voltage sag is recovered and it causes inrush current in transformer. Effects of voltage sag depth, duration and initial point on wave have been analyzed in this paper. Initial point on wave can produce maximum inrush current in five leg transformers while comparing with three leg transformers. The magnetic circuit symmetry of five leg transformer produces the more symmetrical shape of inrush current curves versus initial point on wave and sag duration than three leg transformer. The simulations show that current peak has a periodical dependence on sag duration and linear dependence on sag depth. Inrush current that is produced in three phase five leg transformer is higher than three phase three leg transformer.
Abstract: The measurement of anesthetic depth is necessary in
anesthesiology. NN10 is very simple method among the RR intervals
analysis methods. NN10 parameter means the numbers of above the 10
ms intervals of the normal to normal RR intervals.
Bispectrum analysis is defined as 2D FFT. EEG signal reflected the
non-linear peristalsis phenomena according to the change brain
function. After analyzing the bispectrum of the 2 dimension, the most
significant power spectrum density peaks appeared abundantly at the
specific area in awakening and anesthesia state. These points are
utilized to create the new index since many peaks appeared at the
specific area in the frequency coordinate. The measured range of an
index was 0-100. An index is 20-50 at an anesthesia, while the index is
90-60 at the awake.
In this paper, the relation between NN10 parameter using ECG and
bisepctrum index using EEG is observed to estimate the depth of
anesthesia during anesthesia and then we estimated the utility of the
anesthetic.
Abstract: A generalised relational data model is formalised for
the representation of data with nested structure of arbitrary depth. A
recursive algebra for the proposed model is presented. All the
operations are formally defined. The proposed model is proved to be
a superset of the conventional relational model (CRM). The
functionality and validity of the model is shown by a prototype
implementation that has been undertaken in the functional
programming language Miranda.
Abstract: In this article an isotropic linear elastic half-space with
a cylindrical cavity of finite length is considered to be under the
effect of a ring shape time-harmonic torsion force applied at an
arbitrary depth on the surface of the cavity. The equation of
equilibrium has been written in a cylindrical coordinate system. By
means of Fourier cosine integral transform, the non-zero
displacement component is obtained in the transformed domain. With
the aid of the inversion theorem of the Fourier cosine integral
transform, the displacement is obtained in the real domain. With the
aid of boundary conditions, the involved boundary value problem for
the fundamental solution is reduced to a generalized Cauchy singular
integral equation. Integral representation of the stress and
displacement are obtained, and it is shown that their degenerated
form to the static problem coincides with existing solutions in the
literature.
Abstract: Hybrid algorithm is the hot issue in Computational
Intelligence (CI) study. From in-depth discussion on Simulation
Mechanism Based (SMB) classification method and composite patterns,
this paper presents the Mamdani model based Adaptive Neural
Fuzzy Inference System (M-ANFIS) and weight updating formula in
consideration with qualitative representation of inference consequent
parts in fuzzy neural networks. M-ANFIS model adopts Mamdani
fuzzy inference system which has advantages in consequent part.
Experiment results of applying M-ANFIS to evaluate traffic Level
of service show that M-ANFIS, as a new hybrid algorithm in computational
intelligence, has great advantages in non-linear modeling,
membership functions in consequent parts, scale of training data and
amount of adjusted parameters.
Abstract: Lean, which was initially developed by Toyota, is
widely implemented in other companies to improve competitiveness.
This research is an attempt to identify the adoption of lean in the
production system of Malaysian car manufacturer, Proton using case
study approach. To gain the in-depth information regarding lean
implementation, an activity on the assembly line called Set Parts
Supply (SPS) was studied. The result indicates that by using lean
principles, tools and techniques in the implementation of SPS enabled
to achieve the goals on safety, quality, cost, delivery and morale. The
implementation increased the size of the workspace, improved the
quality of assembly and the delivery of parts supply, reduced the
manpower, achieved cost savings on electricity and also increased the
motivation of manpower in respect of attendance at work. A
framework of SPS implementation is suggested as a contribution for
lean practices in production system.
Abstract: This paper presents the study of hardness profile of spur gear heated by induction heating process in function of the machine parameters, such as the power (kW), the heating time (s) and the generator frequency (kHz). The global work is realized by 3D finite-element simulation applied to the process by coupling and resolving the electromagnetic field and the heat transfer problems, and it was performed in three distinguished steps. First, a Comsol 3D model was built using an adequate formulation and taking into account the material properties and the machine parameters. Second, the convergence study was conducted to optimize the mesh. Then, the surface temperatures and the case depths were deeply analyzed in function of the initial current density and the heating time in medium frequency (MF) and high frequency (HF) heating modes and the edge effect were studied. Finally, the simulations results are validated using experimental tests.
Abstract: The objective of this study is to design an adaptive
neuro-fuzzy inference system (ANFIS) for estimation of surface
roughness in grinding process. The Used data have been generated
from experimental observations when the wheel has been dressed
using a rotary diamond disc dresser. The input parameters of model
are dressing speed ratio, dressing depth and dresser cross-feed rate
and output parameter is surface roughness. In the experimental
procedure the grinding conditions are constant and only the dressing
conditions are varied. The comparison of the predicted values and the
experimental data indicates that the ANFIS model has a better
performance with respect to back-propagation neural network
(BPNN) model which has been presented by the authors in previous
work for estimation of the surface roughness.
Abstract: Prior to 1975, women in Laos suffered from having
reduced levels of power over decision-making in their families and in
their communities. This has had a negative impact on their ability to
develop their own identities. Their roles were identified as being
responsible for household activities and making preparations for their
marriage. Many women lost opportunities to get educated and access
the outdoor work that might have empowered them to improve their
situations. So far, no accurate figures of either emigrants or return
migrants have been compiled but it appears that most of them were
women, and it was women who most and more frequently remitted
money home. However, very few recent studies have addressed the
relationship between remittances and the roles of women in Laos.
This study, therefore, aims at redressing to some extent the
deficiencies in knowledge. Qualitative techniques were used to gather
data, including individual in-depth interviews and direct observation
in combination with the content analysis method. Forty women in
Vientiane Municipality and Savannakhet province were individually
interviewed. It was found that the monetary remittance was typically
used for family security and well-being; on fungible activities; on
economic and business activities; and on community development,
especially concerning hospitality and providing daily household
necessities. Remittances played important roles in improving many
respondents- livelihoods and positively changed their identities in
families and communities. Women became empowered as they were
able to start commercial businesses, rather than taking care of (just)
housework, children and elders. Interviews indicated that 92.5% of
the respondents their quality of lives improved, 90% felt happier in
their families and 82.5% felt conflicts in their families were reduced.
Abstract: The main aim of this work is to establish the
capabilities of new green buildings to ascertain off-grid electricity
generation based on the integration of wind turbines in the
conceptual model of a rotating tower [2] in Dubai. An in depth
performance analysis of the WinWind 3.0MW [3] wind turbine is
performed. Data based on the Dubai Meteorological Services is
collected and analyzed in conjunction with the performance analysis
of this wind turbine. The mathematical model is compared with
Computational Fluid Dynamics (CFD) results based on a conceptual
rotating tower design model. The comparison results are further
validated and verified for accuracy by conducting experiments on a
scaled prototype of the tower design. The study concluded that
integrating wind turbines inside a rotating tower can generate enough
electricity to meet the required power consumption of the building,
which equates to a wind farm containing 9 horizontal axis wind
turbines located at an approximate area of 3,237,485 m2 [14].
Abstract: In order to improve the simulation effects of space cold
black environment, this paper described a rectangular channel plate
heat sink. By using fluid mechanics theory and finite element method,
the internal fluid flow and heat transfer in heat sink was numerically
simulated to analyze the impact of channel structural on fluid flow and
heat transfer. The result showed that heat sink temperature uniformity
is well, and the impact of channel structural on the heat sink
temperature uniformity is not significant. The channel depth and
spacing are important factors which affect the fluid flow and heat
transfer in the heat sink. The two factors of heat transfer and resistance
need to be considered comprehensively to determine the optimal flow
structure parameters.
Abstract: Biological, psychological and social experiences and
perceptions of healthcare services in patients medically diagnosed of
coronary heart disease were investigated using a sample of 10
participants whose responses to the in-depth interview questions
were analyzed based on inter-and-intra-case analyses. The results
obtained revealed that advancing age, single status, divorce and/or
death of spouse and the issue of single parenting negatively impacted
patients- biopsychosocial experiences. The patients- experiences of
physical signs and symptoms, anxiety and depression, past serious
medical conditions, use of self-prescribed medications, family
history of poor mental/medical or physical health, nutritional
problems and insufficient physical activities heightened their risk of
coronary attack. Collectivist culture served as a big source of relieve
to the patients. Patients- temperament, experience of different
chronic life stresses/challenges, mood alteration, regular drinking,
smoking/gambling, and family/social impairments compounded their
health situation. Patients were satisfied with the biomedical services
rendered by the healthcare personnel, whereas their psychological
and social needs were not attended to. Effective procedural treatment
model, a holistic and multidimensional approach to the treatment of
heart disease patients was proposed.
Abstract: A good green building design project, designers should consider not only energy consumption, but also healthy and comfortable needs of inhabitants. In recent years, the Taiwan government paid attentions on both carbon reduction and indoor air quality issues, which be presented in the legislation of Building Codes and other regulations. Taiwan located in hot and humid climates, dampness in buildings leads to significant microbial pollution and building damage. This means that the high temperature and humidity present a serious indoor air quality issue. The interactions between vapor transfers and energy fluxes are essential for the whole building Heat Air and Moisture (HAM) response. However, a simulation tool with short calculation time, property accuracy and interface is needed for practical building design processes. In this research, we consider the vapor transfer phenomenon of building materials as well as temperature and humidity and energy consumption in a building space. The simulation bases on the EMPD method, which was performed by EnergyPlus, a simulation tool developed by DOE, to simulate the indoor moisture variation in a one-zone residential unit based on the Effective Moisture Penetration Depth Method, which is more suitable for practical building design processes.
Abstract: Column leach test has been performed to examine the
behavior of leaching of sodium, calcium and potassium in landfills.
In the column leach apparatus, two different layers of contaminated
and uncontaminated soils of different height ratios (ratio of depth of
contaminated soil to the depth of uncontaminated soil) are taken.
Water is poured from an overhead tank at a particular flowrate to the
inlet of the soil column for a certain ponding depth over the
contaminated soil. Subsequent infiltration causes leaching and the
leachates are collected from the bottom of the column. The
concentrations of Na, Ca and K in the leachate are measured using
flame photometry. The experiments are further extended by changing
the rates of flow from the overhead tank to the inlet of the column in
achieving the same ponding depth. The experiments are performed
for different scenarios in which the height ratios are altered and the
variations of concentrations of Na, Ca, and K are observed. The study
brings an estimation of leaching in landfill sites for different heights
and precipitation intensity where a ponding depth is maintained over
the landfill. It has been observed that the leaching behavior of Na,
Ca, and K are not similar. Calcium exhibits highest amount of
leaching compared to Sodium and Potassium under similar
experimental conditions.
Abstract: The main purpose of this research was to study how to communicate the identity of the Bangpoo, Samu tPrakan province for ecotourism. The qualitative data was collected through studying related materials, exploring the area, in-depth interviews with three groups of people: three directly responsible officers who were key informants of the district, twenty foreign tourists and five Thai tourist guides. A content analysis was used to analyze the qualitative data. The two main findings of the study were as follows:
The identity of Bangpoo, Samut Prakan province. This establishment was near the Mouth of the Gulf of Thailand for normal people and tourists, consisting of rest accommodations. There are restaurants where food and drinks are served, rich mangrove forests, Banpoo seaside resort and mangrove trees. Bangpoo seaside resort is characterized by muddy beacheswhere the greatest number of seagulls can be seen from March to May each year.
The communication of the identity of Bangpoo, Samut Prakan province which the researcher could find and design to present in English materials can be summed up in 3 items: 1) The history of Bangpoo, Samut Prakan province 2) The Learning center of Ecotourism: Seagulls and Mangrove forest 3) How to keep Banpoo, Samut Prakran province for ecotourism.
Abstract: Surface roughness (Ra) is one of the most important requirements in machining process. In order to obtain better surface roughness, the proper setting of cutting parameters is crucial before the process take place. This research presents the development of mathematical model for surface roughness prediction before milling process in order to evaluate the fitness of machining parameters; spindle speed, feed rate and depth of cut. 84 samples were run in this study by using FANUC CNC Milling α-Τ14ιE. Those samples were randomly divided into two data sets- the training sets (m=60) and testing sets(m=24). ANOVA analysis showed that at least one of the population regression coefficients was not zero. Multiple Regression Method was used to determine the correlation between a criterion variable and a combination of predictor variables. It was established that the surface roughness is most influenced by the feed rate. By using Multiple Regression Method equation, the average percentage deviation of the testing set was 9.8% and 9.7% for training data set. This showed that the statistical model could predict the surface roughness with about 90.2% accuracy of the testing data set and 90.3% accuracy of the training data set.
Abstract: This research paper presents a framework on how to
build up malware dataset.Many researchers took longer time to
clean the dataset from any noise or to transform the dataset into a
format that can be used straight away for testing. Therefore, this
research is proposing a framework to help researchers to speed up
the malware dataset cleaningprocesses which later can be used for
testing. It is believed, an efficient malware dataset cleaning
processes, can improved the quality of the data, thus help to improve
the accuracy and the efficiency of the subsequent analysis. Apart
from that, an in-depth understanding of the malware taxonomy is
also important prior and during the dataset cleaning processes. A
new Trojan classification has been proposed to complement this
framework.This experiment has been conducted in a controlled lab
environment and using the dataset from VxHeavens dataset. This
framework is built based on the integration of static and dynamic
analyses, incident response method and knowledge database
discovery (KDD) processes.This framework can be used as the basis
guideline for malware researchers in building malware dataset.
Abstract: Parallel Prefix addition is a technique for improving
the speed of binary addition. Due to continuing integrating intensity
and the growing needs of portable devices, low-power and highperformance
designs are of prime importance. The classical parallel
prefix adder structures presented in the literature over the years
optimize for logic depth, area, fan-out and interconnect count of logic
circuits. In this paper, a new architecture for performing 8-bit, 16-bit
and 32-bit Parallel Prefix addition is proposed. The proposed prefix
adder structures is compared with several classical adders of same
bit width in terms of power, delay and number of computational
nodes. The results reveal that the proposed structures have the least
power delay product when compared with its peer existing Prefix
adder structures. Tanner EDA tool was used for simulating the adder
designs in the TSMC 180 nm and TSMC 130 nm technologies.
Abstract: In order to monitor the water table depth on soil profile
salinity buildup, a field study was carried out during 2006-07. Wheat
(Rabi) and Sorghum (Kharif) fodder were sown in with three
treatments. The results showed that watertable depth lowered from
1.15m to 2.89 m depth at the end of experiment. With lower of
watertable depth, pH, ECe and SAR decreased under crops both
without and with gypsum and increased in fallowing. Soil moisture
depletion was directly proportional to lowering of watertable. With the
application of irrigation water (58cm) pH, ECe and SAR were reduced
in cropped plots, reduction was higher in gypsum applied plots than
non-gypsum plots. In case of fallowing, there was increase in pH, EC,
while slight reduction occurred in SAR values. However, soil salinity
showed an increasing upward trend under fallowing and its value in
0-30 cm soil layer was the highest amongst the treatments.
Abstract: A CFD software was employed to analyze the
characteristics of the flat round porous aerostatic bearings. The effects
of gap between the bearing and the guide way and the porosity of the
porous material on the load capacity of the bearing were studied. The
adequacy of the simulation model and the approach was verified. From
the parametric study, it is found that the depth of the flow path does not
influence the load capacity of the bearing; the load capacity of the
bearing will decrease if the thickness of the porous material increases
or the porous material protrudes above the bearing housing; the
variation of the chamfer at the edge of the bearing does not affect the
bearing load capacity. For a bearing with an air gap of 5μm and a
porosity of 0.1, the average load capacity and the pressure distribution
of the bearing are nearly unchanged no matter the bearing moves at a
constant or a varying speed.