Abstract: This paper presents a methodology to harvest the kinetic energy of the raindrops using piezoelectric devices. In the study 1m×1m PVDF (Polyvinylidene fluoride) piezoelectric membrane, which is fixed by the four edges, is considered for the numerical simulation on deformation of the membrane due to the impact of the raindrops. Then according to the drop size of the rain, the simulation is performed classifying the rainfall types into three categories as light stratiform rain, moderate stratiform rain and heavy thundershower. The impact force of the raindrop is dependent on the terminal velocity of the raindrop, which is a function of raindrop diameter. The results were then analyzed to calculate the harvestable energy from the deformation of the piezoelectric membrane.
Abstract: The article deals with numerical investigation of axisymmetric
subsonic air to air ejector. An analysis of flow and mixing
processes in cylindrical mixing chamber are made. Several modes
with different velocity and ejection ratio are presented. The mixing
processes are described and differences between flow in the initial
region of mixing and the main region of mixing are described. The
lengths of both regions are evaluated. Transition point and point
where the mixing processes are finished are identified. It was found
that the length of the initial region of mixing is strongly dependent on
the velocity ratio, while the length of the main region of mixing is
dependent on velocity ratio only slightly.
Abstract: In a travelling wave thermoacoustic device, the
regenerator sandwiched between a pair of (hot and cold) heat
exchangers constitutes the so-called thermoacoustic core, where the
thermoacoustic energy conversion from heat to acoustic power takes
place. The temperature gradient along the regenerator caused by the
two heat exchangers excites and maintains the acoustic wave in the
resonator. The devices are called travelling wave thermoacoustic
systems because the phase angle difference between the pressure and
velocity oscillation is close to zero in the regenerator. This paper
presents the construction and testing of a thermoacoustic engine
equipped with a ceramic regenerator, made from a ceramic material
that is usually used as catalyst substrate in vehicles- exhaust systems,
with fine square channels (900 cells per square inch). The testing
includes the onset temperature difference (minimum temperature
difference required to start the acoustic oscillation in an engine), the
acoustic power output, thermal efficiency and the temperature profile
along the regenerator.
Abstract: Background: Tissue Doppler Echocardiography
(TDE) assesses diastolic function more accurately than routine pulse
Doppler echo. Assessment of the effects of dynamic and static
exercises on the heart by using TDE can provides new information
about the athlete-s heart syndrome. Methods: This study was
conducted on 20 elite wrestlers, 14 endurance runners at national
level and 21 non-athletes as the control group. Participants underwent
two-dimensional echocardiography, standard Doppler and TDE.
Results: Wrestlers had the highest left ventricular mass index, enddiastolic
inter-ventricular septum thickness and left ventricular
Posterior wall thickness. Runners had the highest Left ventricular
end-diastolic volume, LV ejection fraction, stroke volume and
cardiac output. In TDE, the early diastolic velocity of mitral annulus
to the late diastolic velocity ratio in athletic groups was greater than
the controls with no significant difference. Conclusion: In spite of
cardiac morphological changes in athletes, TDE shows that cardiac
diastolic function won-t be adversely affected.
Abstract: A steady two-phase flow model has been developed to simulate the drying process of porous particle in a pneumatic conveying dryer. The model takes into account the momentum, heat and mass transfer between the continuous phase and the dispersed phase. A single particle model was employed to calculate the evaporation rate. In this model the pore structure is simplified to allow the dominant evaporation mechanism to be readily identified at all points within the duct. The predominant mechanism at any time depends upon the pressure, temperature and the diameter of pore from which evaporating is occurring. The model was validated against experimental studies of pneumatic transport at low and high speeds as well as pneumatic drying. The effects of operating conditions on the dryer parameters are studied numerically. The present results show that the drying rate is enhanced as the inlet gas temperature and the gas flow rate increase and as the solid mass flow rate deceases. The present results also demonstrate the necessity of measuring the inlet gas velocity or the solid concentration in any experimental analysis.
Abstract: In this study, the dispersion of heavy particles line in
an isotropic and incompressible three-dimensional turbulent flow has
been studied using the Kinematic Simulation techniques to find out
the evolution of the line fractal dimension. The fractal dimension of
the line is found in the case of different particle gravity (in practice,
different values of particle drift velocity) in the presence of small
particle inertia with a comparison with that obtained in the diffusion
case of material line at the same Reynolds number. It can be
concluded for the dispersion of heavy particles line in turbulent flow
that the particle gravity affect the fractal dimension of the line for
different particle gravity velocities in the range 0.2 < W < 2. With
the increase of the particle drift velocity, the fractal dimension of the
line decreases which may be explained as the particles pass many
scales in their journey in the direction of the gravity and the particles
trajectories do not affect by these scales at high particle drift
velocities.
Abstract: Multi criteria decision analysis (MDCA) covers both
data and experience. It is very common to solve the problems with
many parameters and uncertainties. GIS supported solutions improve
and speed up the decision process. Weighted grading as a MDCA
method is employed for solving the geotechnical problems. In this
study, geotechnical parameters namely soil type; SPT (N) blow
number, shear wave velocity (Vs) and depth of underground water
level (DUWL) have been engaged in MDCA and GIS. In terms of
geotechnical aspects, the settlement suitability of the municipal area
was analyzed by the method. MDCA results were compatible with
the geotechnical observations and experience. The method can be
employed in geotechnical oriented microzoning studies if the criteria
are well evaluated.
Abstract: Our results showed that treatment with both
cyclooxygenase (COX1 or COX2) inhibitors impair reproduction
parameters of the medaka. Resveratrol (COX1 inhibitor) caused an
decrease in the number of spawning females at the first week of
feeding fish with experimental diets. In the group treated with NS-
398 (COX2 inhibitor) we found the lowest sperm velocity parameters
and decreased linearity of movement. The ovaries of the medaka fed
feed supplemented with Resveratrol or NS-398 were confirmed to
have a lower share of matured oocytes however during the
experiment (four weeks) the number of eggs spawned by females was
similar. Both inhibitors in fish diet (20 mg/kg body weight/day)
caused a decrease in the embryo survival. Our results revealed that
for the medaka female reproduction, activity of both COX enzymes
might be necessary whereas males reproduction competence, as
expressed by sperm motility parameters, might be related to COX2
activity.
Abstract: An experimental investigation was performed on pulp
liquid flow in straight ducts with a square cross section. Fully
developed steady flow was visualized and the fiber concentration was
obtained using a light-section method developed by the author et al.
The obtained results reveal quantitatively, in a definite form, the
distribution of the fiber concentration. From the results and
measurements of pressure loss, it is found that the flow characteristics
of pulp liquid in ducts can be classified into five patterns. The
relationships among the distributions of mean and fluctuation of fiber
concentration, the pressure loss and the flow velocity are discussed,
and then the features for each pattern are extracted. The degree of
nonuniformity of the fiber concentration, which is indicated by the
standard deviation of its distribution, is decreased from 0.3 to 0.05
with an increase in the velocity of the tested pulp liquid from 0.4 to
0.8%.
Abstract: In designing river intakes and diversion structures, it is paramount that the sediments entering the intake are minimized or, if possible, completely separated. Due to high water velocity, sediments can significantly damage hydraulic structures especially when mechanical equipment like pumps and turbines are used. This subsequently results in wasting water, electricity and further costs. Therefore, it is prudent to investigate and analyze the performance of lateral intakes affected by sediment control structures. Laboratory experiments, despite their vast potential and benefits, can face certain limitations and challenges. Some of these include: limitations in equipment and facilities, space constraints, equipment errors including lack of adequate precision or mal-operation, and finally, human error. Research has shown that in order to achieve the ultimate goal of intake structure design – which is to design longlasting and proficient structures – the best combination of sediment control structures (such as sill and submerged vanes) along with parameters that increase their performance (such as diversion angle and location) should be determined. Cost, difficulty of execution and environmental impacts should also be included in evaluating the optimal design. This solution can then be applied to similar problems in the future. Subsequently, the model used to arrive at the optimal design requires high level of accuracy and precision in order to avoid improper design and execution of projects. Process of creating and executing the design should be as comprehensive and applicable as possible. Therefore, it is important that influential parameters and vital criteria is fully understood and applied at all stages of choosing the optimal design. In this article, influential parameters on optimal performance of the intake, advantages and disadvantages, and efficiency of a given design are studied. Then, a multi-criterion decision matrix is utilized to choose the optimal model that can be used to determine the proper parameters in constructing the intake.
Abstract: This paper deals with analysis of flexural stiffness,
indentation and their energies in three point loading of sandwich
beams with composite faces from Eglass/epoxy and cores from
Polyurethane or PVC. Energy is consumed in three stages of
indentation in laminated beam, indentation of sandwich beam and
bending of sandwich beam. Theory of elasticity is chosen to present
equations for indentation of laminated beam, then these equations
have been corrected to offer better results. An analytical model has
been used assuming an elastic-perfectly plastic compressive behavior
of the foam core. Classical theory of beam is used to describe three
point bending. Finite element (FE) analysis of static indentation
sandwich beams is performed using the FE code ABAQUS. The
foam core is modeled using the crushable foam material model and
response of the foam core is experimentally characterized in uniaxial
compression.
Three point bending and indentation have been done
experimentally in two cases of low velocity and higher velocity
(quasi-impact) of loading. Results can describe response of beam in
terms of core and faces thicknesses, core material, indentor diameter,
energy absorbed, and length of plastic area in the testing. The
experimental results are in good agreement with the analytical and
FE analyses. These results can be used as an introduction for impact
loading and energy absorbing of sandwich structures.
Abstract: Electrophoretic motion of a liquid droplet within an
uncharged cylindrical pore is investigated theoretically in this study. It
is found that the boundary effect in terms of the reduction of droplet
mobility (droplet velocity per unit strength of the applied electric field)
is very significant when the double layer surrounding the droplet is
thick, and diminishes as it gets very thin. Moreover, the viscosity ratio
of the ambient fluid to the internal one, σ, is a crucial factor in
determining its electrophoretic behavior. The boundary effect is less
significant as the viscosity ratio gets high. Up to 70% mobility
reduction is observed when this ratio is low (σ = 0.01), whereas only
40% reduction when it is high (σ = 100). The results of this study can
be utilized in various fields of biotechnology, such as a biosensor or a
lab-on-a-chip device.
Abstract: The presented paper shows the possibility of using
holographic interferometry for measurement of temperature field in
moving fluids. There are a few methods for identification of velocity
fields in fluids, such us LDA, PIV, hot wire anemometry. It is very
difficult to measure the temperature field in moving fluids. One of the
often used methods is Constant Current Anemometry (CCA), which
is a point temperature measurement method. Data are possibly
acquired at frequencies up to 1000Hz. This frequency should be
limiting factor for using of CCA in fluid when fast change of
temperature occurs. This shortcoming of CCA measurements should
be overcome by using of optical methods such as holographic
interferometry. It is necessary to employ a special holographic setup
with double sensitivity instead of the commonly used Mach-Zehnder
type of holographic interferometer in order to attain the parameters
sufficient for the studied case. This setup is not light efficient like the
Mach-Zehnder type but has double sensitivity. The special technique
of acquiring and phase averaging of results from holographic
interferometry is also presented. The results from the holographic
interferometry experiments will be compared with the temperature
field achieved by methods CCA method.
Abstract: Present study focuses on studying the oscillatory
behavior of jet diffusion flames. At a particular jet exit velocity, the
flames are seen to exhibit natural flickering. Initially the flickering
process is not continuous. In this transition region as well as in the
continuous flickering regime, the flickering displays multiple
frequency oscillations. The response of the flame to the exit velocity
profile of the burner is also studied using three types of burners. The
entire range of natural flickering is investigated by capturing high
speed digital images and processing them using a MATLAB code.
Abstract: Blood pulse is an important human physiological signal commonly used for the understanding of the individual physical health. Current methods of non-invasive blood pulse sensing require direct contact or access to the human skin. As such, the performances of these devices tend to vary with time and are subjective to human body fluids (e.g. blood, perspiration and skin-oil) and environmental contaminants (e.g. mud, water, etc). This paper proposes a simulation model for the novel method of non-invasive acquisition of blood pulse using the disturbance created by blood flowing through a localized magnetic field. The simulation model geometry represents a blood vessel, a permanent magnet, a magnetic sensor, surrounding tissues and air in 2-dimensional. In this model, the velocity and pressure fields in the blood stream are described based on Navier-Stroke equations and the walls of the blood vessel are assumed to have no-slip condition. The blood assumes a parabolic profile considering a laminar flow for blood in major artery near the skin. And the inlet velocity follows a sinusoidal equation. This will allow the computational software to compute the interactions between the magnetic vector potential generated by the permanent magnet and the magnetic nanoparticles in the blood. These interactions are simulated based on Maxwell equations at the location where the magnetic sensor is placed. The simulated magnetic field at the sensor location is found to assume similar sinusoidal waveform characteristics as the inlet velocity of the blood. The amplitude of the simulated waveforms at the sensor location are compared with physical measurements on human subjects and found to be highly correlated.
Abstract: In this paper we compare the response of linear and
nonlinear neural network-based prediction schemes in prediction of
received Signal-to-Interference Power Ratio (SIR) in Direct
Sequence Code Division Multiple Access (DS/CDMA) systems. The
nonlinear predictor is Multilayer Perceptron MLP and the linear
predictor is an Adaptive Linear (Adaline) predictor. We solve the
problem of complexity by using the Minimum Mean Squared Error
(MMSE) principle to select the optimal predictors. The optimized
Adaline predictor is compared to optimized MLP by employing
noisy Rayleigh fading signals with 1.8 GHZ carrier frequency in an
urban environment. The results show that the Adaline predictor can
estimates SIR with the same error as MLP when the user has the
velocity of 5 km/h and 60 km/h but by increasing the velocity up-to
120 km/h the mean squared error of MLP is two times more than
Adaline predictor. This makes the Adaline predictor (with lower
complexity) more suitable than MLP for closed-loop power control
where efficient and accurate identification of the time-varying
inverse dynamics of the multi path fading channel is required.
Abstract: The present study focuses on the discussion over the
parameter of Artificial Neural Network (ANN). Sensitivity analysis is
applied to assess the effect of the parameters of ANN on the prediction
of turbidity of raw water in the water treatment plant. The result shows
that transfer function of hidden layer is a critical parameter of ANN.
When the transfer function changes, the reliability of prediction of
water turbidity is greatly different. Moreover, the estimated water
turbidity is less sensitive to training times and learning velocity than
the number of neurons in the hidden layer. Therefore, it is important to
select an appropriate transfer function and suitable number of neurons
in the hidden layer in the process of parameter training and validation.
Abstract: The main aim of this work is to establish the
capabilities of new green buildings to ascertain off-grid electricity
generation based on the integration of wind turbines in the
conceptual model of a rotating tower [2] in Dubai. An in depth
performance analysis of the WinWind 3.0MW [3] wind turbine is
performed. Data based on the Dubai Meteorological Services is
collected and analyzed in conjunction with the performance analysis
of this wind turbine. The mathematical model is compared with
Computational Fluid Dynamics (CFD) results based on a conceptual
rotating tower design model. The comparison results are further
validated and verified for accuracy by conducting experiments on a
scaled prototype of the tower design. The study concluded that
integrating wind turbines inside a rotating tower can generate enough
electricity to meet the required power consumption of the building,
which equates to a wind farm containing 9 horizontal axis wind
turbines located at an approximate area of 3,237,485 m2 [14].
Abstract: Numerical study of a plane jet occurring in a vertical
heated channel is carried out. The aim is to explore the influence of
the forced flow, issued from a flat nozzle located in the entry section
of a channel, on the up-going fluid along the channel walls. The
Reynolds number based on the nozzle width and the jet velocity
ranges between 3 103 and 2.104; whereas, the Grashof number based
on the channel length and the wall temperature difference is 2.57
1010. Computations are established for a symmetrically heated
channel and various nozzle positions. The system of governing
equations is solved with a finite volumes method. The obtained
results show that the jet-wall interactions activate the heat transfer,
the position variation modifies the heat transfer especially for low
Reynolds numbers: the heat transfer is enhanced for the adjacent
wall; however it is decreased for the opposite one. The numerical
velocity and temperature fields are post-processed to compute the
quantities of engineering interest such as the induced mass flow rate,
and the Nusselt number along the plates.
Abstract: The data measurement of mean velocity has been
taken for the wake of single circular cylinder with three different diameters for two different velocities. The effects of change in
diameter and in velocity are studied in self-similar coordinate system.
The spatial variations of velocity defect and that of the half-width
have been investigated. The results are compared with those
published by H.Schlichting. In the normalized coordinates, it is also observed that all cases except for the first station are self-similar. By attention to self-similarity profiles of mean velocity, it is observed for all the cases at the each station curves tend to zero at a same point.