Abstract: The main objective of aircraft aerodynamics is to
enhance the aerodynamic characteristics and maneuverability of the
aircraft. This enhancement includes the reduction in drag and stall
phenomenon. The airfoil which contains dimples will have
comparatively less drag than the plain airfoil. Introducing dimples on
the aircraft wing will create turbulence by creating vortices which
delays the boundary layer separation resulting in decrease of pressure
drag and also increase in the angle of stall. In addition, wake
reduction leads to reduction in acoustic emission. The overall
objective of this paper is to improve the aircraft maneuverability by
delaying the flow separation point at stall and thereby reducing the
drag by applying the dimple effect over the aircraft wing. This project
includes both computational and experimental analysis of dimple
effect on aircraft wing, using NACA 0018 airfoil. Dimple shapes of
Semi-sphere, hexagon, cylinder, square are selected for the analysis;
airfoil is tested under the inlet velocity of 30m/s and 60m/s at
different angle of attack (5˚, 10˚, 15˚, 20˚, and 25˚). This analysis
favors the dimple effect by increasing L/D ratio and thereby
providing the maximum aerodynamic efficiency, which provides the
enhanced performance for the aircraft.
Abstract: For a bluff body, dimples behave like roughness
elements in stimulating a turbulent boundary layer, leading to delayed
flow separation, a smaller wake and lower form drag. This is very
different in principle from the application of dimples to streamlined
body, where any reduction in drag would be predominantly due to a
reduction in skin friction. In the present work, a car model with
different dimple geometry is simulated using k-ε turbulence modeling
to determine its effect to the aerodynamics performance. Overall, the
results show that the application of dimples manages to reduce the
drag coefficient of the car model.
Abstract: The aim of this work is to build a model based on
tissue characterization that is able to discriminate pathological and
non-pathological regions from three-phasic CT images. With our
research and based on a feature selection in different phases, we are
trying to design a neural network system with an optimal neuron
number in a hidden layer. Our approach consists of three steps:
feature selection, feature reduction, and classification. For each
region of interest (ROI), 6 distinct sets of texture features are
extracted such as: first order histogram parameters, absolute gradient,
run-length matrix, co-occurrence matrix, autoregressive model, and
wavelet, for a total of 270 texture features. When analyzing more
phases, we show that the injection of liquid cause changes to the high
relevant features in each region. Our results demonstrate that for
detecting HCC tumor phase 3 is the best one in most of the features
that we apply to the classification algorithm. The percentage of
detection between pathology and healthy classes, according to our
method, relates to first order histogram parameters with accuracy of
85% in phase 1, 95% in phase 2, and 95% in phase 3.
Abstract: Micro-alloyed steel components are used in
automotive industry for the necessity to make the manufacturing
process cycles shorter when compared to conventional steel by
eliminating heat treatment cycles, so an important saving of costs and
energy can be reached by reducing the number of operations. Microalloying
elements like vanadium, niobium or titanium have been
added to medium carbon steels to achieve grain refinement with or
without precipitation strengthening along with uniform
microstructure throughout the matrix. Present study reports the
applicability of medium carbon vanadium micro-alloyed steel in hot
forging. Forgeability has been determined with respect to different
cooling rates, after forging in a hydraulic press at 50% diameter
reduction in temperature range of 900-11000C. Final microstructures,
hardness, tensile strength, and impact strength have been evaluated.
The friction coefficients of different lubricating conditions, viz.,
graphite in hydraulic oil, graphite in furnace oil, DF 150 (Graphite,
Water-Based) die lubricant and dry or without any lubrication were
obtained from the ring compression test for the above micro-alloyed
steel. Results of ring compression tests indicate that graphite in
hydraulic oil lubricant is preferred for free forging and dry lubricant
is preferred for die forging operation. Exceptionally good forgeability
and high resistance to fracture, especially for faster cooling rate has
been observed for fine equiaxed ferrite-pearlite grains, some amount
of bainite and fine precipitates of vanadium carbides and
carbonitrides. The results indicated that the cooling rate has a
remarkable effect on the microstructure and mechanical properties at
room temperature.
Abstract: In order to detect and quantify the phenolic contents
of a wastewater with biosensors, two working electrodes based on
modified Poly(Pyrrole) films were fabricated. Enzyme horseradish
peroxidase was used as biomolecule of the prepared electrodes.
Various phenolics were tested at the biosensor. Phenol detection was
realized by electrochemical reduction of quinones produced by
enzymatic activity. Analytical parameters were calculated and the
results were compared with each other.
Abstract: Effect of biopesticide from wood vinegar and
extracted substances from 3 medicinal plants such as: non taai yak
(Stemona tuberosa Lour), boraphet (Tinospora crispa Mier) and
derris (Derris elliptica Roxb) were tested on the age five years of
pomelo. The selected pomelo was carried out for insects’ pest control
and its quality. The experimental site was located at farmer’s orchard
in Phichit Province, Thailand. This study was undertaken during the
drought season (December to March). The extracted from plants and
wood vinegar were evaluated in 6 treatments: 1) water as control; 2)
wood vinegar; 3) S. tuberosa Lour; 4) T. crispa Mier; 5) D. elliptica
Roxb; 6) mixed (wood vinegar + S. tuberosa Lour + T. crispa Mier +
D. elliptica Roxb). The experiment was RCB with 6 treatments and 3
replications per treatment. The results showed that T. crispa Mier was
the highest effectiveness for reduction population of thrips
(Scirtothrips dorsalis Hood) and citrus leaf miner (Phyllocnistis
citrella Stainton) at 14.10 and 15.37 respectively, followed by
treatment of mixed, D. elliptica Roxb, S. tuberosa Lour and wood
vinegar with significance different. Additionally, T. crispa Mier
promoted the high quality of harvested pomelo in term of thickness
of skin at 12.45 mm and S. tuberosa Lour gave the high quality of the
pomelo in term of firmness (276.5 kg/cm2) and brix (11.0%).
Abstract: Non-linear FEM calculations are indispensable when
important technical information like operating performance of a
rubber component is desired. For example rubber bumpers built into
air-spring structures may undergo large deformations under load,
which in itself shows non-linear behavior. The changing contact
range between the parts and the incompressibility of the rubber
increases this non-linear behavior further. The material
characterization of an elastomeric component is also a demanding
engineering task.
The shape optimization problem of rubber parts led to the study of
FEM based calculation processes. This type of problems was posed
and investigated by several authors. In this paper the time demand of
certain calculation methods are studied and the possibilities of time
reduction is presented.
Abstract: Microbial fuel cells (MFCs) represent a promising
technology for simultaneous bioelectricity generation and wastewater
treatment. Catalysts are significant portions of the cost of microbial
fuel cell cathodes. Many materials have been tested as aqueous
cathodes, but air-cathodes are needed to avoid energy demands for
water aeration. The sluggish oxygen reduction reaction (ORR) rate at
air cathode necessitates efficient electrocatalyst such as carbon
supported platinum catalyst (Pt/C) which is very costly. Manganese
oxide (MnO2) was a representative metal oxide which has been
studied as a promising alternative electrocatalyst for ORR and has
been tested in air-cathode MFCs. However the single MnO2 has poor
electric conductivity and low stability. In the present work, the MnO2
catalyst has been modified by doping Pt nanoparticle. The goal of the
work was to improve the performance of the MFC with minimum Pt
loading. MnO2 and Pt nanoparticles were prepared by hydrothermal
and sol gel methods, respectively. Wet impregnation method was
used to synthesize Pt/MnO2 catalyst. The catalysts were further used
as cathode catalysts in air-cathode cubic MFCs, in which anaerobic
sludge was inoculated as biocatalysts and palm oil mill effluent
(POME) was used as the substrate in the anode chamber. The asprepared
Pt/MnO2 was characterized comprehensively through field
emission scanning electron microscope (FESEM), X-Ray diffraction
(XRD), X-ray photoelectron spectroscopy (XPS), and cyclic
voltammetry (CV) where its surface morphology, crystallinity,
oxidation state and electrochemical activity were examined,
respectively. XPS revealed Mn (IV) oxidation state and Pt (0)
nanoparticle metal, indicating the presence of MnO2 and Pt.
Morphology of Pt/MnO2 observed from FESEM shows that the
doping of Pt did not cause change in needle-like shape of MnO2
which provides large contacting surface area. The electrochemical
active area of the Pt/MnO2 catalysts has been increased from 276 to
617 m2/g with the increase in Pt loading from 0.2 to 0.8 wt%. The
CV results in O2 saturated neutral Na2SO4 solution showed that
MnO2 and Pt/MnO2 catalysts could catalyze ORR with different
catalytic activities. MFC with Pt/MnO2 (0.4 wt% Pt) as air cathode
catalyst generates a maximum power density of 165 mW/m3, which
is higher than that of MFC with MnO2 catalyst (95 mW/m3). The
open circuit voltage (OCV) of the MFC operated with MnO2 cathode
gradually decreased during 14 days of operation, whereas the MFC
with Pt/MnO2 cathode remained almost constant throughout the
operation suggesting the higher stability of the Pt/MnO2 catalyst.
Therefore, Pt/MnO2 with 0.4 wt% Pt successfully demonstrated as an
efficient and low cost electrocatalyst for ORR in air cathode MFC with higher electrochemical activity, stability and hence enhanced
performance.
Abstract: Environmental impact assessment techniques have
been developed as a result of the worldwide efforts to reduce the
environmental impact of global warming. By using the quantification
method in the construction industry, it is now possible to manage the
greenhouse gas is to systematically evaluate the impact on the
environment over the entire construction process. In particular, the
proportion of greenhouse gas emissions at the production stage of
construction material occupied is high, and efforts are needed in
particular in the construction field.
In this research, intended for concrete products for the construction
materials, by using the LCA method, we compared the results of
environmental impact assessment and carbon emissions of developing
products that have been applied low-carbon technologies compared to
existing products. As a results, by introducing a raw material of
industrial waste, showed carbon reduction. Through a comparison of
the carbon emission reduction effect of low carbon technologies, it is
intended to provide academic data for the evaluation of greenhouse
gases in the construction sector and the development of low carbon
technologies of the future.
Abstract: In this paper, an analysis of some model order
reduction techniques is presented. A new hybrid algorithm for model
order reduction of linear time invariant systems is compared with the
conventional techniques namely Balanced Truncation, Hankel Norm
reduction and Dominant Pole Algorithm (DPA). The proposed hybrid
algorithm is known as Clustering Dominant Pole Algorithm (CDPA),
is able to compute the full set of dominant poles and its cluster center
efficiently. The dominant poles of a transfer function are specific
eigenvalues of the state space matrix of the corresponding dynamical
system. The effectiveness of this novel technique is shown through
the simulation results.
Abstract: The study examined the effect of Bonny Light whole
crude oil (WC) and its water soluble fraction (WSF) on the activities
of antioxidant enzymes (catalase (CAT) and superoxide dismutase
(SOD)) and crude mitochondria ATPases in the radicle of
germinating bean (Vigna unguiculata). The percentage germination,
level of lipid peroxidation, antioxidant enzyme and mitochondria
Ca2+ and Mg2+ ATPase activities were measured in the radicle of
bean after 7, 14 and 21 days post germination. Viable bean seeds
were planted in soils contaminated with 10ml, 25ml and 50ml of
whole crude oil (WC) and its water soluble fraction (WSF) to obtain
2, 5 and 10% v/w crude oil contamination. There was dose dependent
reduction of the number of bean seeds that germinated in the
contaminated soils compared with control (p
Abstract: Since columns are the most important elements of the
structures, failure of one column in a critical location can cause a
progressive collapse. In this respect, the repair and strengthening of
columns is a very important subject to reduce the building failure and
to keep the columns capacity. Twenty columns with different
parameters is tested and analysis. Eleven typical confined reinforced
concrete (RC) columns with different types of techniques are
assessment. And also, four confined concrete columns with plastic
tube (PVC) are tested with and with four paralleling tested of
unconfined plain concrete. The techniques of confined RC columns
are mortar strengthening, Steel rings strengthening, FRP
strengthening. Moreover, the technique of confined plain concrete
(PC) column is used PVC tubes. The columns are tested under
uniaxial compressive loads studied the effect of confinement on the
structural behavior of circular RC columns. Test results for each
column are presented in the form of crack patterns, stress-strain
curves. Test results show that confining of the RC columns using
different techniques of strengthening results significant improvement
of the general behavior of the columns and can used in construction.
And also, tested confined PC columns with PVC tubes results shown
that the confined PC with PVC tubes can be used in economical
building. The theoretical model for predicted column capacity is
founded with experimental factor depends on the confined techniques
used and the strain reduction.
Abstract: Ocimum americanum L (Lamiaceae) is an annual herb
that is native to tropical Africa. The in vitro and in vivo antioxidant
activity of its aqueous extract was carefully investigated by assessing
the DPPH radical scavenging activity, ABTS radical scavenging
activity and hydrogen peroxide radical scavenging activity. The
reducing power, total phenol, total flavonoids and flavonols content
of the extract were also evaluated. The data obtained revealed that the
extract is rich in polyphenolic compounds and scavenged the radicals
in a concentration dependent manner. This was done in comparison
with the standard antioxidants such as BHT and Vitamin C. Also, the
induction of oxidative damage with paracetamol (2000 mg/kg)
resulted in the elevation of lipid peroxides and significant (P < 0.05)
decrease in activities of superoxide dismutase, glutathione
peroxidase, glutathione reductase and catalase in the liver and kidney
of rats. However, the pretreatment of rats with aqueous extract of O.
americanum leaves (200 and 400 mg/kg) and silymarin (100 mg/kg)
caused a significant (P < 0.05) reduction in the values of lipid
peroxides and restored the levels of antioxidant parameters in these
organs. These findings suggest that the leaves of O. americanum have
potent antioxidant properties which may be responsible for its
acclaimed folkloric uses.
Abstract: Speech enhancement is a long standing problem with
numerous applications like teleconferencing, VoIP, hearing aids and
speech recognition. The motivation behind this research work is to
obtain a clean speech signal of higher quality by applying the optimal
noise cancellation technique. Real-time adaptive filtering algorithms
seem to be the best candidate among all categories of the speech
enhancement methods. In this paper, we propose a speech
enhancement method based on Recursive Least Squares (RLS)
adaptive filter of speech signals. Experiments were performed on
noisy data which was prepared by adding AWGN, Babble and Pink
noise to clean speech samples at -5dB, 0dB, 5dB and 10dB SNR
levels. We then compare the noise cancellation performance of
proposed RLS algorithm with existing NLMS algorithm in terms of
Mean Squared Error (MSE), Signal to Noise ratio (SNR) and SNR
Loss. Based on the performance evaluation, the proposed RLS
algorithm was found to be a better optimal noise cancellation
technique for speech signals.
Abstract: This study is concerned with the optimization of
fermentation parameters for the hyper production of mannanase from
Fusarium oxysporum SS-25 employing two step statistical strategy
and kinetic characterization of crude enzyme preparation. The
Plackett-Burman design used to screen out the important factors in
the culture medium revealed 20% (w/w) wheat bran, 2% (w/w) each
of potato peels, soyabean meal and malt extract, 1% tryptone, 0.14%
NH4SO4, 0.2% KH2PO4, 0.0002% ZnSO4, 0.0005% FeSO4, 0.01%
MnSO4, 0.012% SDS, 0.03% NH4Cl, 0.1% NaNO3 in brewer’s spent
grain based medium with 50% moisture content, inoculated with
2.8×107 spores and incubated at 30oC for 6 days to be the main
parameters influencing the enzyme production. Of these factors, four
variables including soyabean meal, FeSO4, MnSO4 and NaNO3 were
chosen to study the interactive effects and their optimum levels in
central composite design of response surface methodology with the
final mannanase yield of 193 IU/gds. The kinetic characterization
revealed the crude enzyme to be active over broader temperature and
pH range. This could result in 26.6% reduction in kappa number with
4.93% higher tear index and 1% increase in brightness when used to
treat the wheat straw based kraft pulp. The hydrolytic potential of
enzyme was also demonstrated on both locust bean gum and guar
gum.
Abstract: The progress of industry integrated circuits in recent
years has been pushed by continuous miniaturization of transistors.
With the reduction of dimensions of components at 0.1 micron and
below, new physical effects come into play as the standard simulators
of two dimensions (2D) do not consider. In fact the third dimension
comes into play because the transverse and longitudinal dimensions
of the components are of the same order of magnitude. To describe
the operation of such components with greater fidelity, we must
refine simulation tools and adapted to take into account these
phenomena. After an analytical study of the static characteristics of
the component, according to the different operating modes, a
numerical simulation is performed of field-effect transistor with
submicron gate MESFET GaInP. The influence of the dimensions of
the gate length is studied. The results are used to determine the
optimal geometric and physical parameters of the component for their
specific applications and uses.
Abstract: High Peak to Average Power Ratio (PAPR) of the
transmitted signal is a serious problem in multicarrier systems (MC),
such as Orthogonal Frequency Division Multiplexing (OFDM), or in
Multi-Carrier Code Division Multiple Access (MC-CDMA) systems,
due to large number of subcarriers. This effect is possible reduce with
some PAPR reduction techniques. Spreading sequences at the
presence of Saleh and Rapp models of high power amplifier (HPA)
have big influence on the behavior of system. In this paper we
investigate the bit-error-rate (BER) performance of MC-CDMA
systems. Basically we can see from simulations that the MC-CDMA
system with Iterative algorithm can be providing significantly better
results than the MC-CDMA system. The results of our analyses are
verified via simulation.
Abstract: Iris codes contain bits with different entropy. This
work investigates different strategies to reduce the size of iris
code templates with the aim of reducing storage requirements and
computational demand in the matching process. Besides simple subsampling
schemes, also a binary multi-resolution representation as
used in the JBIG hierarchical coding mode is assessed. We find that
iris code template size can be reduced significantly while maintaining
recognition accuracy. Besides, we propose a two-stage identification
approach, using small-sized iris code templates in a pre-selection
stage, and full resolution templates for final identification, which
shows promising recognition behaviour.
Abstract: Vancron 40, a nitrided powder metallurgical tool
Steel, is used in cold work applications where the predominant failure
mechanisms are adhesive wear or galling. Typical applications of
Vancron 40 are among others fine blanking, cold extrusion, deep
drawing and cold work rolls for cluster mills. Vancron 40 positive
results for cold work rolls for cluster mills and as a tool for some
severe metal forming process makes it competitive compared to other
type of work rolls that require higher precision, among others in cold
rolling of thin stainless steel, which required high surface finish
quality. In this project, three roll materials for cold rolling of stainless
steel strip was examined, Vancron 40, Narva 12B (a high-carbon,
high-chromium tool steel alloyed with tungsten) and Supra 3 (a
Chromium-molybdenum tungsten-vanadium alloyed high speed
steel). The purpose of this project was to study the depth profiles of
the ironed stainless steel strips, emergence of galling and to study the
lubrication performance used by steel industries. Laboratory
experiments were conducted to examine scratch of the strip, galling
and surface roughness of the roll materials under severe tribological
conditions. The critical sliding length for onset of galling was
estimated for stainless steel with four different lubricants. Laboratory
experiments result of performance evaluation of resistance capability
of rolls toward adhesive wear under severe conditions for low and
high reductions. Vancron 40 in combination with cold rolling
lubricant gave good surface quality, prevents galling of
metal surfaces and good bearing capacity.
Abstract: Member States shall establish zones and
agglomerations throughout their territory to assess and manage air
quality in order to comply with European directives.
In Italy decree 155/2010, transposing Directive 2008/50/EC on
ambient air quality and cleaner air for Europe, merged into a single
act the previous provisions on ambient air quality assessment and
management, including those resulting from the implementation of
Directive 2004/107/EC relating to arsenic, cadmium, nickel, mercury
and polycyclic aromatic hydrocarbons in ambient air.
Decree 155/2010 introduced stricter rules for identifying zones on
the basis of the characteristics of the territory in spite of considering
pollution levels, as it was in the past. The implementation of such
new criteria has reduced the great variability of the previous zoning,
leading to a significant reduction of the total number of zones and to
a complete and uniform ambient air quality assessment and
management throughout the Country.
The present document is related to the new zones definition in
Italy according to Decree 155/2010. In particular the paper contains
the description and the analysis of the outcome of zoning and
classification.