Abstract: Vancron 40, a nitrided powder metallurgical tool
Steel, is used in cold work applications where the predominant failure
mechanisms are adhesive wear or galling. Typical applications of
Vancron 40 are among others fine blanking, cold extrusion, deep
drawing and cold work rolls for cluster mills. Vancron 40 positive
results for cold work rolls for cluster mills and as a tool for some
severe metal forming process makes it competitive compared to other
type of work rolls that require higher precision, among others in cold
rolling of thin stainless steel, which required high surface finish
quality. In this project, three roll materials for cold rolling of stainless
steel strip was examined, Vancron 40, Narva 12B (a high-carbon,
high-chromium tool steel alloyed with tungsten) and Supra 3 (a
Chromium-molybdenum tungsten-vanadium alloyed high speed
steel). The purpose of this project was to study the depth profiles of
the ironed stainless steel strips, emergence of galling and to study the
lubrication performance used by steel industries. Laboratory
experiments were conducted to examine scratch of the strip, galling
and surface roughness of the roll materials under severe tribological
conditions. The critical sliding length for onset of galling was
estimated for stainless steel with four different lubricants. Laboratory
experiments result of performance evaluation of resistance capability
of rolls toward adhesive wear under severe conditions for low and
high reductions. Vancron 40 in combination with cold rolling
lubricant gave good surface quality, prevents galling of
metal surfaces and good bearing capacity.
Abstract: The operating control parameters of injection
flushing type of electrical discharge machining process on stainless
steel 304 workpiece with copper tools are being optimized
according to its individual machining characteristic i.e. material
removal rate (MRR). Lower MRR during EDM machining process
may decrease its- machining productivity. Hence, the quality
characteristic for MRR is set to higher-the-better to achieve the
optimum machining productivity. Taguchi method has been used
for the construction, layout and analysis of the experiment for each
of the machining characteristic for the MRR. The use of Taguchi
method in the experiment saves a lot of time and cost of preparing
and machining the experiment samples. Therefore, an L18
Orthogonal array which was the fundamental component in the
statistical design of experiments has been used to plan the
experiments and Analysis of Variance (ANOVA) is used to
determine the optimum machining parameters for this machining
characteristic. The control parameters selected for this
optimization experiments are polarity, pulse on duration, discharge
current, discharge voltage, machining depth, machining diameter
and dielectric liquid pressure. The result had shown that the higher
the discharge voltage, the higher will be the MRR.
Abstract: This study aimed to present the mechanical
performance evaluation of the dynamic hip screw (DHS) for
trochanteric fracture by means of finite element method. The
analyses were performed based on stainless steel and titanium
implant material definitions at various stages of bone healing and
including implant removal. The assessment of the mechanical
performance used two parameters, von Mises stress to evaluate the
strength of bone and implant and elastic strain to evaluate fracture
stability. The results show several critical aspects of dynamic hip
screw for trochanteric fracture stabilization. In the initial stage of
bone healing process, partial weight bearing should be applied to
avoid the implant failure. In the late stage of bone healing, stainless
steel implant should be removed.
Abstract: The operating control parameters of injection
flushing type of electrical discharge machining process on stainless
steel 304 workpiece using copper tools are being optimized
according to its individual machining characteristic i.e. Electrode
Wear Ratio (EWR). Higher EWR would give bad dimensional
precision for the EDM machined workpiece because of high
electrode wear. Hence, the quality characteristic for EWR is set to
lower-the-better to achieve the optimum dimensional precision for
the machined workpiece. Taguchi method has been used for the
construction, layout and analysis of the experiment for EWR
machining characteristic. The use of Taguchi method in the
experiment saves a lot of time and cost of preparing and machining
the experiment samples. Therefore, an L18 Orthogonal array
which was the fundamental component in the statistical design of
experiments has been used to plan the experiments and Analysis of
Variance (ANOVA) is used to determine the optimum machining
parameters for this machining characteristic. The control
parameters selected for this optimization experiments are polarity,
pulse on duration, discharge current, discharge voltage, machining
depth, machining diameter and dielectric liquid pressure. The
result had shown that negative polarity machining parameter
setting will decreases EWR.