Abstract: A new dual-fluid concept was studied that could eventually find application for cold-gas propulsion for small space satellites or other constant flow applications. In basic form, the concept uses two different refrigerant working fluids, each having a different saturation vapor pressure. The higher vapor pressure refrigerant remains in the saturation phase and is used to pressurize the lower saturation vapor pressure fluid (the propellant) which remains in the compressed liquid phase. A demonstration thruster concept based on this principle was designed and built to study its operating characteristics. An automotive-type electronic fuel injector was used to meter and deliver the propellant. Ejected propellant mass and momentum were measured for several combinations of refrigerants and hydrocarbon fluids. The thruster has the advantage of delivering relatively large total impulse at low tank pressure within a small volume.
Abstract: Water vapour transport properties of gypsum block
are studied in dependence on relative humidity using inverse analysis
based on genetic algorithm. The computational inverse analysis is
performed for the relative humidity profiles measured along the
longitudinal axis of a rod sample. Within the performed transient
experiment, the studied sample is exposed to two environments with
different relative humidity, whereas the temperature is kept constant.
For the basic gypsum characterisation and for the assessment of input
material parameters necessary for computational application of
genetic algorithm, the basic material properties of gypsum are
measured as well as its thermal and water vapour storage parameters.
On the basis of application of genetic algorithm, the relative
humidity dependent water vapour diffusion coefficient and water
vapour diffusion resistance factor are calculated.
Abstract: This was the first document revealing the
investigation of protein hydrolysate production optimization from J.
curcas cake. Proximate analysis of raw material showed 18.98%
protein, 5.31% ash, 8.52% moisture and 12.18% lipid. The
appropriate protein hydrolysate production process began with
grinding the J. curcas cake into small pieces. Then it was suspended
in 2.5% sodium hydroxide solution with ratio between solution/ J.
curcas cake at 80:1 (v/w). The hydrolysis reaction was controlled at
temperature 50 °C in water bath for 45 minutes. After that, the
supernatant (protein hydrolysate) was separated using centrifuge at
8000g for 30 minutes. The maximum yield of resulting protein
hydrolysate was 73.27 % with 7.34% moisture, 71.69% total protein,
7.12% lipid, 2.49% ash. The product was also capable of well
dissolving in water.
Abstract: Fecal coliform bacteria are widely used as indicators of
sewage contamination in surface water. However, there are some
disadvantages in these microbial techniques including time consuming
(18-48h) and inability in discriminating between human and animal
fecal material sources. Therefore, it is necessary to seek a more
specific indicator of human sanitary waste. In this study, the feasibility
was investigated to apply caffeine and human pharmaceutical
compounds to identify the human-source contamination. The
correlation between caffeine and fecal coliform was also explored.
Surface water samples were collected from upstream, middle-stream
and downstream points respectively, along Rochor Canal, as well as 8
locations of Marina Bay. Results indicate that caffeine is a suitable
chemical tracer in Singapore because of its easy detection (in the range
of 0.30-2.0 ng/mL), compared with other chemicals monitored.
Relative low concentrations of human pharmaceutical compounds (<
0.07 ng/mL) in Rochor Canal and Marina Bay water samples make
them hard to be detected and difficult to be chemical tracer. However,
their existence can help to validate sewage contamination. In addition,
it was discovered the high correlation exists between caffeine
concentration and fecal coliform density in the Rochor Canal water
samples, demonstrating that caffeine is highly related to the
human-source contamination.
Abstract: In this paper we present discretization and decomposition methods for a multi-component transport model of a chemical vapor deposition (CVD) process. CVD processes are used to manufacture deposition layers or bulk materials. In our transport model we simulate the deposition of thin layers. The microscopic model is based on the heavy particles, which are derived by approximately solving a linearized multicomponent Boltzmann equation. For the drift-process of the particles we propose diffusionreaction equations as well as for the effects of heat conduction. We concentrate on solving the diffusion-reaction equation with analytical and numerical methods. For the chemical processes, modelled with reaction equations, we propose decomposition methods and decouple the multi-component models to simpler systems of differential equations. In the numerical experiments we present the computational results of our proposed models.
Abstract: In this paper, an improvement of PDLZW implementation
with a new dictionary updating technique is proposed. A
unique dictionary is partitioned into hierarchical variable word-width
dictionaries. This allows us to search through dictionaries in parallel.
Moreover, the barrel shifter is adopted for loading a new input string
into the shift register in order to achieve a faster speed. However,
the original PDLZW uses a simple FIFO update strategy, which is
not efficient. Therefore, a new window based updating technique
is implemented to better classify the difference in how often each
particular address in the window is referred. The freezing policy
is applied to the address most often referred, which would not be
updated until all the other addresses in the window have the same
priority. This guarantees that the more often referred addresses would
not be updated until their time comes. This updating policy leads
to an improvement on the compression efficiency of the proposed
algorithm while still keep the architecture low complexity and easy
to implement.
Abstract: This research simulates one of the natural phenomena,
the ocean wave. Our goal is to be able to simulate the ocean wave at
real-time rate with the water surface interacting with objects. The
wave in this research is calm and smooth caused by the force of the
wind above the ocean surface. In order to make the simulation of the
wave real-time, the implementation of the GPU and the
multithreading techniques are used here. Based on the fact that the
new generation CPUs, for personal computers, have multi cores, they
are useful for the multithread. This technique utilizes more than one
core at a time. This simulation is programmed by C language with
OpenGL. To make the simulation of the wave look more realistic, we
applied an OpenGL technique called cube mapping (environmental
mapping) to make water surface reflective and more realistic.
Abstract: Elastic boundary eigensolution problems are converted
into boundary integral equations by potential theory. The kernels of
the boundary integral equations have both the logarithmic and Hilbert
singularity simultaneously. We present the mechanical quadrature
methods for solving eigensolutions of the boundary integral equations
by dealing with two kinds of singularities at the same time. The methods
possess high accuracy O(h3) and low computing complexity. The
convergence and stability are proved based on Anselone-s collective
compact theory. Bases on the asymptotic error expansion with odd
powers, we can greatly improve the accuracy of the approximation,
and also derive a posteriori error estimate which can be used for
constructing self-adaptive algorithms. The efficiency of the algorithms
are illustrated by numerical examples.
Abstract: The RK5GL3 method is a numerical method for solving
initial value problems in ordinary differential equations, and is
based on a combination of a fifth-order Runge-Kutta method and
3-point Gauss-Legendre quadrature. In this paper we describe an
effective local error control algorithm for RK5GL3, which uses local
extrapolation with an eighth-order Runge-Kutta method in tandem
with RK5GL3, and a Hermite interpolating polynomial for solution
estimation at the Gauss-Legendre quadrature nodes.
Abstract: Vernonia divergens Benth., commonly known as
“Insulin Plant” (Fam: Asteraceae) is a potent sugar killer. Locally the
leaves of the plant, boiled in water are successfully administered to a
large number of diabetic patients. The present study evaluates the
putative anti-diabetic ingredients, isolated from the in vivo and in
vitro grown plantlets of V. divergens for their antimicrobial and
anticancer activities. Sterilized explants of nodal segments were
cultured on MS (Musashige and Skoog, 1962) medium in presence of
different combinations of hormones. Multiple shoots along with
bunch of roots were regenerated at 1mg l-1 BAP and 0.5 mg l-1 NAA.
Micro-plantlets were separated and sub-cultured on the double
strength (2X) of the above combination of hormones leading to
increased length of roots and shoots. These plantlets were
successfully transferred to soil and survived well in nature. The
ethanol extract of plantlets from both in vivo & in vitro sources were
prepared in soxhlet extractor and then concentrated to dryness under
reduced pressure in rotary evaporator. Thus obtainedconcentrated
extracts showed significant inhibitory activity against gram
negative bacteria like Escherichia coli and Pseudomonas
aeruginosa but no inhibition was found against gram positive
bacteria. Further, these ethanol extracts were screened for in vitro
percentage cytotoxicity at different time periods (24 h, 48 h and 72 h)
of different dilutions. The in vivo plant extract inhibited the growth of
EAC mouse cell lines in the range of 65, 66, 78, and 88% at 100, 50,
25 & 12.5μg mL-1 but at 72 h of treatment. In case of the extract of in
vitro origin, the inhibition was found against EAC cell lines even at
48h. During spectrophotometric scanning, the extracts exhibited
different maxima (ʎ) - four peaks in in vitro extracts as against single
in in vivo preparation suggesting the possible change in the nature of
ingredients during micropropagation through tissue culture
techniques.
Abstract: The mesoporous MoO3/γ-Al2O3 catalyst was prepared
by incipient wetness impregnation method aiming to investigate the
effect of drying method and molybdenum content on the catalyst
property and performance towards the oxidation of benzothiophene
(BT), dibenzothiophene (DBT) and 4,6-dimethyle dibenzothiophene
(4,6-DMDBT) with H2O2 for deep oxidative desulfurization of diesel
fuel. The catalyst was characterized by XRD, BET, BJH and SEM
method. The catalyst with 10wt.% and 15wt.% Mo content represent
same optimum performance for DBT and 4,6-DMDBT removal, but
a catalyst with 10wt.% Mo has higher efficiency than 15wt.% Mo for
BT conversion. The SEM images show that use of rotary evaporator
in drying step reaches a more homogenous impregnation. The
oxidation reactivity of different sulfur compounds was studied which
followed the order of DBT>4,6-DMDBT>>BT.
Abstract: Gamboge disorder (GD) or fruit damage by the yellow sap is a major problem in mangosteen. Mangosteen plants varied in the level of GD, from very low or non GD to low, moderate and high GD. However it was difficult to differentiate between GD and non GD plants because evaluation of the disorder is strongly influenced by environment. In this study we investigated the usefulness of primer designed from bioinformatics related to cell wall strength, termed as MCWS, to predict GD. Plant materials used were 28 mangosteen plants selected based on percentage of GD categorized as high, moderate, low and very low or non GD. The result showed that the specific DNA fragments were absent in the high GD accessions. The MCWS marker suggests as a novel polymorphic marker for GD in mangosteen as well as a marker for detect variability in mangosteen as apomictic plant.
Abstract: The importance for manipulating an incorporated
scaffold and directing cell behaviors is well appreciated for tissue
engineering. Here, we developed newly nano-topographic oxidized
silicon nanosponges capable of being various chemical modifications
to provide much insight into the fundamental biology of how cells
interact with their surrounding environment in vitro. A wet etching
technique is exerted to allow us fabricated the silicon nanosponges in a
high-throughput manner. Furthermore, various organo-silane
chemicals enabled self-assembled on the surfaces by vapor deposition.
We have found that Chinese hamster ovary (CHO) cells displayed
certain distinguishable morphogenesis, adherent responses, and
biochemical properties while cultured on these chemical modified
nano-topographic structures in compared with the planar oxidized
silicon counterparts, indicating that cell behaviors can be influenced
by certain physical characteristic derived from nano-topography in
addition to the hydrophobicity of contact surfaces crucial for cell
adhesion and spreading. Of particular, there were predominant
nano-actin punches and slender protrusions formed while cells were
cultured on the nano-topographic structures. This study shed potential
applications of these nano-topographic biomaterials for controlling
cell development in tissue engineering or basic cell biology research.
Abstract: Image segmentation is an important step in image
processing. Major developments in medical imaging allow
physicians to use potent and non-invasive methods in order to
evaluate structures, performance and to diagnose human diseases. In
this study, an active contour was used to extract vessel networks
from color retina images. Automatic analysis of retina vessels
facilitates calculation of arterial index which is required to diagnose
some certain retinopathies.
Abstract: The focal spot of a high intensity focused ultrasound
transducer is small. To heat a large target volume, multiple treatment spots are required. If the power of each treatment spot is fixed, it could
results in insufficient heating of initial spots and over-heating of later ones, which is caused by the thermal diffusion. Hence, to produce a
uniform heated volume, the delivered energy of each treatment spot
should be properly adjusted. In this study, we proposed an iterative, extrapolation technique to adjust the required ultrasound energy of
each treatment spot. Three different scanning pathways were used to evaluate the performance of this technique. Results indicate that by using the proposed technique, uniform heating volume could be obtained.
Abstract: Autofluorescence (AF) bronchoscopy is an
established method to detect dysplasia and carcinoma in situ (CIS).
For this reason the “Sotiria" Hospital uses the Karl Storz D-light
system. However, in early tumor stages the visualization is not that
obvious. With the help of a PC, we analyzed the color images we
captured by developing certain tools in Matlab®. We used statistical
methods based on texture analysis, signal processing methods based
on Gabor models and conversion algorithms between devicedependent
color spaces. Our belief is that we reduced the error made
by the naked eye. The tools we implemented improve the quality of
patients' life.
Abstract: The objective of this research was to determine the
potency of indigenous acid-aluminium tolerant Bradyrhizobium
japonicum as producer of indole acetic acid (IAA) and applied it as
nitrogen fixation on local soybeans viz Anjasmoro, Tanggamus
(yellow soybean seeds), and Detam (black soybean seed). Three
isolates of acid-aluminium tolerant Bradyrhizobium japonicum (BJ)
were used in this research, i.e. BJ 11 (wt), BJ 11 (19) - BJ 11(wt)
mutant, and USDA 110 as a reference isolate. All of isolates tested to
produce the IAA by using Salkowsky method. Effect of IAA
production by each of B. japonicum was tested on growth pouch and
greenhouse using three varieties of soybean. All isolates could grow
well and produce IAA on yeast mannitol broth (YMB) medium in
the presence of 0.5 mM L-tryptophan. BJ 11 (19) produced the
highest of IAA at 4 days incubation compared to BJ 11 (wt) and
USDA 110. All tested isolates of Bradyrhizobium japonicum have
showed effect on stimulating the formation of root nodules in
soybean varieties grown on Leonard bottle. The concentration of
IAA on root nodules of soybean symbiotic with B. japonicum was
significantly different with control, except on the treatment using
Tanggamus soybean.
Abstract: Breast cancer is the most common malignancy in the
world among women. Many therapies have been designed to treat
this disease. Mamectomy, chemotherapy and radiotherapy are still
the main therapies of breast cancer. However, the results were
unsatisfactory and still far from the ideal treatment.
PM 701is a natural product, has anticancer activity. The bioactive
fraction PMF and subfraction PMFK had been isolated from PM701.
PM 701 and its fractions were proved to have a cytotoxic properties
against different cancer cell lines. This article is directed for the
further examination of lyophilized PM701 and its active fractions on
the growth of breast cancer cells (MCF-7). PM 701, PMF or PMFK
were adding to the cultural medium, where MCF-7 is incubated.
PM 701, PMF or PMFK were able to inhibit significantly the
proliferation of MCF-7 cells, Moreover these new agents were
proved to induce apoptosis of the breast cancer cells; through its
direct effect on the nuclei.
Abstract: Among the chemicals used for ammunition production, TNT (Trinitrotoluene) play a significant role since World War I and II. Various types of military weapon utilize TNT in casting process. However, the TNT casting process for warhead is difficult to control the cooling rate of the liquid TNT. This problem occurs because the casting process lacks the equipment to detect the temperature during the casting procedure This study presents the temperature detected by infrared camera to illustrate the cooling rate and cooling zone of curing, and demonstrates the optimization of TNT condition to reduce the risk of air gap occurred in the warhead which can result in the destruction afterward. Premature initiation of explosive-filled projectiles in response to set-back forces during gunfiring cause by casting defects. Finally the study can help improving the process of the TNT casting. The operators can control the curing of TNT inside the case by rising up the heating rod at the proper time. Consequently this can reduce tremendous time of rework if the air gaps occur and increase strength to lower elastic modulus. Therefore, it can be clearly concluded that the use of Infrared Cameras in this process is another method to improve the casting procedure.
Abstract: Maize and Indian mustard are significant crops in
semi-arid climate zones of India. Improved water management
requires precise scheduling of irrigation, which in turn requires an
accurate computation of daily crop evapotranspiration (ETc). Daily
crop evapotranspiration comes as a product of reference
evapotranspiration (ET0) and the growth stage specific crop
coefficients modified for daily variation. The first objective of
present study is to develop crop coefficients Kc for Maize and Indian
mustard. The estimated values of Kc for maize at the four crop
growth stages (initial, development, mid-season, and late season) are
0.55, 1.08, 1.25, and 0.75, respectively, and for Indian mustard the Kc
values at the four growth stages are 0.3, 0.6, 1.12, and 0.35,
respectively. The second objective of the study is to compute daily
crop evapotranspiration from ET0 and crop coefficients. Average
daily ETc of maize varied from about 2.5 mm/d in the early growing
period to > 6.5 mm/d at mid season. The peak ETc of maize is 8.3
mm/d and it occurred 64 days after sowing at the reproductive growth
stage when leaf area index was 4.54. In the case of Indian mustard,
average ETc is 1 mm/d at the initial stage, >1.8 mm/d at mid season
and achieves a peak value of 2.12 mm/d on 56 days after sowing.
Improved schedules of irrigation have been simulated based on daily
crop evapo-transpiration and field measured data. Simulation shows a
close match between modeled and field moisture status prevalent
during crop season.