Abstract: In this article, a high vacuum system for the evaporation of organic semiconductors is introduced and a mathematical model is given. Based on the exact input output linearization a deposition rate controller is designed and tested with different evaporation materials.
Abstract: A steady two-phase flow model has been developed to simulate the drying process of porous particle in a pneumatic conveying dryer. The model takes into account the momentum, heat and mass transfer between the continuous phase and the dispersed phase. A single particle model was employed to calculate the evaporation rate. In this model the pore structure is simplified to allow the dominant evaporation mechanism to be readily identified at all points within the duct. The predominant mechanism at any time depends upon the pressure, temperature and the diameter of pore from which evaporating is occurring. The model was validated against experimental studies of pneumatic transport at low and high speeds as well as pneumatic drying. The effects of operating conditions on the dryer parameters are studied numerically. The present results show that the drying rate is enhanced as the inlet gas temperature and the gas flow rate increase and as the solid mass flow rate deceases. The present results also demonstrate the necessity of measuring the inlet gas velocity or the solid concentration in any experimental analysis.
Abstract: Full - Scale Accelerated Loading System, one part of
“the Eleventh - Five - Year National Grand Technology Infrastructure
Program" is a facility to evaluate the performance and service life of
different kinds of pavements subjected to traffic loading under full -
controlled environment. While simulating the environments of frigid
zone and permafrost zone, the accurate control of air temperature, road
temperature and roadbed temperature are the key points and also
aporias for the designment. In this paper, numerical simulations are
used to determine the design parameters of the frozen soil simulation
system. At first, a brief introduction of the Full - Scale Accelerate
Loading System was given. Then, the temperature control method of
frozen soil simulation system was proposed. Finally, by using finite
element simulations, the optimal design of frozen soil simulation
system was obtained. This proposed design, which was obtained by
finite element simulations, provided significant referents to the
ultimate design of the environment simulation system.
Abstract: This paper provides an exergy analysis of the multistage refrigeration cycle used for C2+ recovery plant. The behavior of an industrial refrigeration cycle with refrigerant propane has been investigated by the exergy method. A computational model based on the exergy analysis is presented for the investigation of the effects of the valves on the exergy losses, the second law of efficiency, and the coefficient of performance (COP) of a vapor compression refrigeration cycle. The equations of exergy destruction and exergetic efficiency for the main cycle components such as evaporators, condensers, compressors, and expansion valves are developed. The relations for the total exergy destruction in the cycle and the cycle exergetic efficiency are obtained. An ethane recovery unit with its refrigeration cycle has been simulated to prepare the exergy analysis. Using a typical actual work input value; the exergetic efficiency of the refrigeration cycle is determined to be 39.90% indicating a great potential for improvements. The simulation results reveal that the exergetic efficiencies of the heat exchanger and expansion sections get the lowest rank among the other compartments of refrigeration cycle. Refrigeration calculations have been carried out through the analysis of T–S and P–H diagrams where coefficient of performance (COP) was obtained as 1.85. The novelty of this article includes the effect and sensitivity analysis of molar flow, pressure drops and temperature on the exergy efficiency and coefficient of performance of the cycle.
Abstract: Due to their high power-to-weight ratio and low cost,
pneumatic actuators are attractive for robotics and automation
applications; however, achieving fast and accurate control of their
position have been known as a complex control problem. A
methodology for obtaining high position accuracy with a linear
pneumatic actuator is presented. During experimentation with a
number of PID classical control approaches over many operations of
the pneumatic system, the need for frequent manual re-tuning of the
controller could not be eliminated. The reason for this problem is
thermal and energy losses inside the cylinder body due to the
complex friction forces developed by the piston displacements.
Although PD controllers performed very well over short periods, it
was necessary in our research project to introduce some form of
automatic gain-scheduling to achieve good long-term performance.
We chose a fuzzy logic system to do this, which proved to be an
easily designed and robust approach. Since the PD approach showed
very good behaviour in terms of position accuracy and settling time,
it was incorporated into a modified form of the 1st order Tagaki-
Sugeno fuzzy method to build an overall controller. This fuzzy gainscheduler
uses an input variable which automatically changes the PD
gain values of the controller according to the frequency of repeated
system operations. Performance of the new controller was
significantly improved and the need for manual re-tuning was
eliminated without a decrease in performance. The performance of
the controller operating with the above method is going to be tested
through a high-speed web network (GRID) for research purposes.
Abstract: Utilization of bagasse ash for silica sources is one of
the most common application for agricultural wastes and valuable
biomass byproducts in sugar milling. The high percentage silica
content from bagasse ash was used as silica source for sodium
silicate solution. Different heating temperature, time and acid
treatment were studies for silica extraction. The silica was
characterized using various techniques including X-ray fluorescence,
X-ray diffraction, Scanning electron microscopy, and Fourier
Transform Infrared Spectroscopy method,. The synthesis conditions
were optimized to obtain the bagasse ash with the maximum silica
content. The silica content of 91.57 percent was achieved from
heating of bagasse ash at 600°C for 3 hours under oxygen feeding
and HCl treatment. The result can be used as value added for bagasse
ash utilization and minimize the environmental impact of disposal
problems.
Abstract: The paper presents the influence of the conventional
ploughing tillage technology in comparison with the minimum
tillage, upon the soil properties, weed control and yield in the case of
maize (Zea mays L.), soya-bean (Glycine hispida L.) and winter
wheat (Triticum aestivum L.) in a three years crop rotation. A
research has been conducted at the University of Agricultural
Sciences and Veterinary Medicine Cluj-Napoca, Romania. The use of
minimum soil tillage systems within a three years rotation: maize,
soya-bean, wheat favorites the rise of the aggregates hydro stability
with 5.6-7.5% on a 0-20 cm depth and 5-11% on 20-30 cm depth.
The minimum soil tillage systems – paraplow, chisel or rotary grape
– are polyvalent alternatives for basic preparation, germination bed
preparation and sowing, for fields and crops with moderate loose
requirements being optimized technologies for: soil natural fertility
activation and rationalization, reduction of erosion, increasing the
accumulation capacity for water and realization of sowing in the
optimal period. The soil tillage system influences the productivity
elements of cultivated species and finally the productions thus
obtained. Thus, related to conventional working system, the
productions registered in minimum tillage working represented 89-
97% in maize, 103-112% in soya-bean, 93-99% in winter-wheat. The
results of investigations showed that the yield is a conclusion soil
tillage systems influence on soil properties, plant density assurance
and on weed control. Under minimum tillage systems in the case of
winter weat as an option for replacing classic ploughing, the best
results in terms of quality indices were obtained from version worked
with paraplow, followed by rotary harrow and chisel. At variants
worked with paraplow were obtained quality indices close to those of
the variant worked with plow, and protein and gluten content was
even higher. At Ariesan variety, highest protein content, 12.50% and
gluten, 28.6% was obtained for the variant paraplow.
Abstract: The k-nearest neighbors (knn) is a simple but effective method of classification. In this paper we present an extended version of this technique for chemical compounds used in High Throughput Screening, where the distances of the nearest neighbors can be taken into account. Our algorithm uses kernel weight functions as guidance for the process of defining activity in screening data. Proposed kernel weight function aims to combine properties of graphical structure and molecule descriptors of screening compounds. We apply the modified knn method on several experimental data from biological screens. The experimental results confirm the effectiveness of the proposed method.
Abstract: Titanium nitride (TiN) has been synthesized using the
sheet plasma negative ion source (SPNIS). The parameters used for
its effective synthesis has been determined from previous
experiments and studies. In this study, further enhancement of the
deposition rate of TiN synthesis and advancement of the SPNIS
operation is presented. This is primarily achieved by the addition of
Sm-Co permanent magnets and a modification of the configuration in
the TiN deposition process. The magnetic enhancement is aimed at
optimizing the sputtering rate and the sputtering yield of the process.
The Sm-Co permanent magnets are placed below the Ti target for
better sputtering by argon. The Ti target is biased from –250V to –
350V and is sputtered by Ar plasma produced at discharge current of
2.5–4A and discharge potential of 60–90V. Steel substrates of
dimensions 20x20x0.5mm3 were prepared with N2:Ar volumetric
ratios of 1:3, 1:5 and 1:10. Ocular inspection of samples exhibit
bright gold color associated with TiN. XRD characterization
confirmed the effective TiN synthesis as all samples exhibit the (200)
and (311) peaks of TiN and the non-stoichiometric Ti2N (220) facet.
Cross-sectional SEM results showed increase in the TiN deposition
rate of up to 0.35μm/min. This doubles what was previously obtained
[1]. Scanning electron micrograph results give a comparative
morphological picture of the samples. Vickers hardness results gave
the largest hardness value of 21.094GPa.
Abstract: Competitive relationships among Bradyrhizobium
japonicum USDA serogroup 123, 122 and 138 were screened versus
the standard commercial soybean variety Williams and two
introductions P1 377578 "671" in a field trial. Displacement of strain
123 by an effective strain should improved N2 fixation. Root nodules
were collected and strain occupancy percentage was determined
using strain specific fluorescent antibodies technique. As anticipated
the strain USDA 123 dominated 92% of nodules due to the high
affinity between the host and the symbiont. This dominance was
consistent and not changed materially either by inoculation practice
or by introducing new strainan. The interrelationship between the
genotype Williams and serogroup 122 & 138 was found very weak
although the cell density of the strain in the rhizosphere area was
equal. On the other hand, the nodule occupancy of genotypes 671 and
166 with rhizobia serogroup 123 was almost diminished to zero. .
The data further exhibited that the genotypes P1 671 and P1 166 have
high affinity to colonize with strains 122 and 138 whereas Williams
was highly promiscuous to strain 123.
Abstract: A novel methodology has been used to design an
evaporator coil of a refrigerant. The methodology used is through a
complete Computer Aided Design /Computer Aided Engineering
approach, by means of a Computational Fluid Dynamic/Finite
Element Analysis model which is executed many times for the
thermal-fluid exploration of several designs' configuration by an
commercial optimizer. Hence the design is carried out automatically
by parallel computations, with an optimization package taking the
decisions rather than the design engineer. The engineer instead takes
decision regarding the physical settings and initializing of the
computational models to employ, the number and the extension of the
geometrical parameters of the coil fins and the optimization tools to
be employed. The final design of the coil geometry found to be better
than the initial design.
Abstract: Wheat prediction was carried out using different meteorological variables together with agro meteorological indices in Ardebil district for the years 2004-2005 & 2005–2006. On the basis of correlation coefficients, standard error of estimate as well as relative deviation of predicted yield from actual yield using different statistical models, the best subset of agro meteorological indices were selected including daily minimum temperature (Tmin), accumulated difference of maximum & minimum temperatures (TD), growing degree days (GDD), accumulated water vapor pressure deficit (VPD), sunshine hours (SH) & potential evapotranspiration (PET). Yield prediction was done two months in advance before harvesting time which was coincide with commencement of reproductive stage of wheat (5th of June). It revealed that in the final statistical models, 83% of wheat yield variability was accounted for variation in above agro meteorological indices.
Abstract: In this work, a Modified Functional Link Artificial
Neural Network (M-FLANN) is proposed which is simpler than a
Multilayer Perceptron (MLP) and improves upon the universal
approximation capability of Functional Link Artificial Neural
Network (FLANN). MLP and its variants: Direct Linear Feedthrough
Artificial Neural Network (DLFANN), FLANN and
M-FLANN have been implemented to model a simulated Water Bath
System and a Continually Stirred Tank Heater (CSTH). Their
convergence speed and generalization ability have been compared.
The networks have been tested for their interpolation and
extrapolation capability using noise-free and noisy data. The results
show that M-FLANN which is computationally cheap, performs
better and has greater generalization ability than other networks
considered in the work.
Abstract: In this study, multiwall carbon nanotubes (MWNTs)
were modified with nitric acid chemically and by dielectric barrier
discharge (DBD) plasma in an oxygen-based atmosphere. Used
carbon nanotubes (CNTs) were prepared by chemical vapour
deposition (CVD) floating catalyst method. For removing amorphous
carbon and metal catalyst, MWNTs were exposed to dry air and
washed with hydrochloric acid. Heating purified CNTs under helium
atmosphere caused elimination of acidic functional groups. Fourier
transformed infrared spectroscopy (FTIR) shows formation of
oxygen containing groups such as C=O and COOH. Brunauer,
Emmett, Teller (BET) analysis revealed that functionalization causes
generation of defects on the sidewalls and opening of the ends of
CNTs. Results of temperature-programmed desorption (TPD) and gas
chromatography(GC) indicate that nitric acid treatment create more
acidic groups than plasma treatment.
Abstract: The objective of this research is to develop the
performance indicators (PIs) in operational level for the Pre-hospital Emergency Medical Service (EMS) system employing in Thailand. This research started with ascertaining the current pre-hospital care
system. The team analyzed the strategies of Narerthorn, a government unit under the ministry of public health, and the existing PIs of the pre-hospital care. Afterwards, the current National Strategic Plan of EMS development (2008-2012) of the Emergency
Medical Institute of Thailand (EMIT) was considered using strategic
analysis to developed Strategy Map (SM) and identified the Success
Factors (SFs). The analysis results from strategy map and SFs were used to develop the Performance Indicators (PIs). To verify the set of
PIs, the team has interviewed with the relevant practitioners for the possibilities to implement the PIs. To this paper, it was to ascertain
that all the developed PIs support the objectives of the strategic plan. Nevertheless, the results showed that the operational level PIs suited
only with the first dimension of National Strategic Plan
(infrastructure and information technology development). Besides,
the SF was the infrastructure development (to contribute the EMS system to people throughout with standard and efficiency both in normally and disaster conditions). Finally, twenty-nine indicators
were developed from the analysis results of SM and SFs.
Abstract: The soil moisture content is an important property of
the soil. The results of mean weekly gravimetric soil moisture
content, measured for the three soil layers within the A horizon,
showed that it was higher for the top 5 cm over the whole period of
monitoring (15/7/2004 up to 10/11/05) with the variation becoming
greater during winter time. This reflects the pattern of rainfall in
Ireland which is spread over the whole year and shows that light
rainfall events during summer time were compensated by loss
through evapotranspiration, but only in the top 5 cm of soil. This
layer had the highest porosity and highest moisture holding capacity
due to the high content of organic matter. The gravimetric soil
moisture contents of the top 5 cm and the underlying 5-15 and 15-25
cm layers show that bottom site of the Hill Field had higher soil
moisture content than the middle and top sites during the whole
period of monitoring.
Abstract: In the last two decades radiofrequency ablation (RFA)
has been considered a promising medical procedure for the treatment
of primary and secondary malignancies. However, the needle-based
electrodes so far developed for this kind of treatment are not suitable
for the thermal ablation of tumors located in hollow organs like
esophagus, colon or bile duct. In this work a tubular electrode
solution is presented. Numerical and experimental analyses were
performed to characterize the volume of the lesion induced. Results
show that this kind of electrode is a feasible solution and numerical
simulation might provide a tool for planning RFA procedure with
some accuracy.
Abstract: Long terms variation of solar insolation had been
widely studied. However, its parallel observations in short time scale
is rather lacking. This paper aims to investigate the short time scale
evolution of solar radiation spectrum (UV, PAR, and NIR bands) due
to atmospheric aerosols and water vapors. A total of 25 days of
global and diffused solar spectrum ranges from air mass 2 to 6 were
collected using ground-based spectrometer with shadowband
technique. The result shows that variation of solar radiation is the
least in UV fraction, followed by PAR and the most in NIR. Broader
variations in PAR and NIR are associated with the short time scale
fluctuations of aerosol and water vapors. The corresponding daily
evolution of UV, PAR, and NIR fractions implies that aerosol and
water vapors variation could also be responsible for the deviation
pattern in the Langley-plot analysis.
Abstract: This paper reports on the results of experimental
investigations of flash evaporation from superheated jet issues
vertically upward from a round straight nozzle of 81.3 mm diameter.
For the investigated range of jet superheat degree and velocity, it was
shown that flash evaporation enhances with initial temperature
increase. Due to the increase of jet inertia and subsequently the delay
of jet shattering, increase of jet velocity was found to result in
increase of evaporation "delay period". An empirical equation
predicts the jet evaporation completion height was developed, this
equation is thought to be useful in designing the flash evaporation
chamber. In attempts for enhancement of flash evaporation, use of
steel wire mesh located at short distance downstream was found
effective with no consequent pressure drop.
Abstract: A good green building design project, designers should consider not only energy consumption, but also healthy and comfortable needs of inhabitants. In recent years, the Taiwan government paid attentions on both carbon reduction and indoor air quality issues, which be presented in the legislation of Building Codes and other regulations. Taiwan located in hot and humid climates, dampness in buildings leads to significant microbial pollution and building damage. This means that the high temperature and humidity present a serious indoor air quality issue. The interactions between vapor transfers and energy fluxes are essential for the whole building Heat Air and Moisture (HAM) response. However, a simulation tool with short calculation time, property accuracy and interface is needed for practical building design processes. In this research, we consider the vapor transfer phenomenon of building materials as well as temperature and humidity and energy consumption in a building space. The simulation bases on the EMPD method, which was performed by EnergyPlus, a simulation tool developed by DOE, to simulate the indoor moisture variation in a one-zone residential unit based on the Effective Moisture Penetration Depth Method, which is more suitable for practical building design processes.