Abstract: In the present study, a steady-state simulation model
has been developed to evaluate the system performance of a
transcritical carbon dioxide heat pump system for simultaneous water
cooling and heating. Both the evaporator (including both two-phase
and superheated zone) and gas cooler models consider the highly
variable heat transfer characteristics of CO2 and pressure drop. The
numerical simulation model of transcritical CO2 heat pump has been
validated by test data obtained from experiments on the heat pump
prototype. Comparison between the test results and the model
prediction for system COP variation with compressor discharge
pressure shows a modest agreement with a maximum deviation of
15% and the trends are fairly similar. Comparison for other operating
parameters also shows fairly similar deviation between the test
results and the model prediction. Finally, the simulation results are
presented to study the effects of operating parameters such as,
temperature of heat exchanger fluid at the inlet, discharge pressure,
compressor speed on system performance of CO2 heat pump, suitable
in a dairy plant where simultaneous cooling at 4oC and heating at
73oC are required. Results show that good heat transfer properties of
CO2 for both two-phase and supercritical region and efficient
compression process contribute a lot for high system COPs.
Abstract: In this paper, the Lennard -Jones potential is applied
to molecules of liquid argon as well as its vapor and platinum as solid
surface in order to perform a non-equilibrium molecular dynamics
simulation to study the microscopic aspects of liquid-vapor-solid
interactions. The channel is periodic in x and y directions and along z
direction it is bounded by atomic walls. It was found that density of
the liquids near the solid walls fluctuated greatly and that the
structure was more like a solid than a liquid. This indicates that the
interactions of solid and liquid molecules are very strong. The
resultant surface tension, liquid density and vapor density are found
to be well predicted when compared with the experimental data for
argon. Liquid and vapor densities were found to depend on the cutoff
radius which induces the use of P3M (particle-particle particle-mesh)
method which was implemented for evaluation of force and surface
tension.
Abstract: This research aims to study employment trends in
printing industry for prepress support by Suan Sunandha University
Fund. The objectives of this research are to explain the trends of the
employment in Thai Printing Industry for prepress in Bangkok and
the description of different personnel that prepress entrepreneur need
and also the problems of employment.
The population of prepress entrepreneurs is about 100
organizations in the area of Bangkok. The questionnaires has been
taken and analyzed with SPSS program by using the average
percentage and standard deviation.
This research is multiple case studies. The conceptual framework
is developed on the basis of the open systems theory.
The research result show that
1. The most of prepress entrepreneur have trend to choose the
employee by any sex, the age 25-29 years old, bachelor degree
and have 1-2 years experience.
2. The most problems are the understanding in job,
communication/relation and the understanding in new
technology.
3. The trends aims to employment in 1-3 years have 57.8% for
prepress industry in Bangkok.
This research suggests that:
1. Thai printing industry for prepress in Bangkok need quality
employee that expert in printing technology.
2. Prepress entrepreneur should have agreement to development
with university for practice the employee.
3. Prepress entrepreneur should support personal to fulfill the
knowledge.
Abstract: The changes in quality properties and nutritional
components in two fermented mugworts (Artemisia capillaries
Thumberg, Artemisiaeasiaticae Nakai) were characterized followed
by the rapid pattern analysis of volatile flavor compounds by Electric
Nose based on SAW(Surface Acoustic Wave) sensor in GC system.
There were remarkable decreases in the pH and small changes in the
total soluble solids after fermentation. The L (lightness) and b
(yellowness) values in Hunter's color system were shown to be
decreased, whilst the a (redness) value was increased by fermentation.
The HPLC analysis demonstrated that total amino acids were
increased in quantity and the essential amino acids were contained
higher in A. asiaticaeNakai than in A. capillaries Thumberg. While
the total polyphenol contents were not affected by fermentation, the
total sugar contents were dramatically decreased. Scopoletinwere
highly abundant in A. capillarisThumberg, however, it was not
detected in A. asiaticaeNakai. Volatile flavor compounds by Electric
Nose showed that the intensity of several peaks were increased much
and seven additional flavor peaks were newly produced after
fermentation. The flavor differences of two mugworts were clearly
distinguished from the image patterns of VaporPrintTM which indicate
that the fermentation enables the two mugworts to have subtle flavor
differences.
Abstract: To strengthen the capital market, there is a need to
integrate the capital markets within the region by removing legal or informal restriction, specifically, stock market liberalization. Thus the paper is to investigate the effects of the subsequent stock market liberalization on stock market integration in 4 ASEAN countries (Malaysia, Indonesia, Thailand, Singapore) and Korea from 1997 to 2007. The correlation between stock market liberalization and stock
market integration are to be examined by analyzing the stock prices
and returns within the region and in comparison with the world
MSCI index. Event study method is to be used with windows of ±12
months and T-7 + T. The results show that the subsequent stock
market liberalization generally, gives minor positive effects to stock
returns, except for one or two countries. The subsequent
liberalization also integrates the markets short-run and long-run.
Abstract: This paper aims to perform the second law analysis of
thermodynamics on the laminar film condensation of pure saturated
vapor flowing in the direction of gravity on an ellipsoid with variable
wall temperature. The analysis provides us understanding how the
geometric parameter- ellipticity and non-isothermal wall temperature
variation amplitude “A." affect entropy generation during film-wise
condensation heat transfer process. To understand of which
irreversibility involved in this condensation process, we derived an
expression for the entropy generation number in terms of ellipticity
and A. The result indicates that entropy generation increases with
ellipticity. Furthermore, the irreversibility due to finite temperature
difference heat transfer dominates over that due to condensate film
flow friction and the local entropy generation rate decreases with
increasing A in the upper half of ellipsoid. Meanwhile, the local
entropy generation rate enhances with A around the rear lower half of
ellipsoid.
Abstract: A feed-forward, back-propagation Artificial Neural
Network (ANN) model has been used to forecast the occurrences of
wastewater overflows in a combined sewerage reticulation system.
This approach was tested to evaluate its applicability as a method
alternative to the common practice of developing a complete
conceptual, mathematical hydrological-hydraulic model for the
sewerage system to enable such forecasts. The ANN approach
obviates the need for a-priori understanding and representation of the
underlying hydrological hydraulic phenomena in mathematical terms
but enables learning the characteristics of a sewer overflow from the
historical data.
The performance of the standard feed-forward, back-propagation
of error algorithm was enhanced by a modified data normalizing
technique that enabled the ANN model to extrapolate into the
territory that was unseen by the training data. The algorithm and the
data normalizing method are presented along with the ANN model
output results that indicate a good accuracy in the forecasted sewer
overflow rates. However, it was revealed that the accurate
forecasting of the overflow rates are heavily dependent on the
availability of a real-time flow monitoring at the overflow structure
to provide antecedent flow rate data. The ability of the ANN to
forecast the overflow rates without the antecedent flow rates (as is
the case with traditional conceptual reticulation models) was found to
be quite poor.
Abstract: Traditionally, Yemini Sidr honey has been reported to
cure liver problems, stomach ulcers, and respiratory disorders. In this
experiment, we evaluated Yemeni Sidr honey for its ability to protect
inflammations caused by acetic acid and formalin -induced writhing,
carrageenan and histamine-induced paw oedema in experimental rat
model. Hyperpyrexia, membrane stabilizing activity, and
phytochemical screening of the honey was also examined. Yemini
Sidr Honey at (100, 200 and 500 mg/kg) exhibited a concentration
dependant inhibition of acetic acid induced and formalin induced
writhing, paw oedema induced by carrageenan & histamine, and
hyperpyrexia induced by brewer's yeast, it also inhibited membrane
stabilizing activity. Phytochemical screenings of the honey reveal the
presence of flavonoids, steroid, alkaloids, saponins and tannins. This
study suggested that Yemeni Sidr honey possess very strong antiinflammatory,
analgesic and antipyretic effects and these effects
would be a result of the phytochemicals present.
Abstract: Urinary Tract Infections (UTI) account for an estimated 25-40% nosocomial infection, out of which 90% are associated with urinary catheter, called Catheter associated urinary tract infection (CAUTI). The microbial populations within CAUTI frequently develop as biofilms. In the present study, microbial contamination of indwelling urinary catheters was investigated. Biofilm forming ability of the isolates was determined by tissue culture plate method. Prevention of biofilm formation in the urinary catheter by Pseudomonas aeruginosa was also determined by coating the catheter with some enzymes, gentamycin and EDTA. It was found that 64% of the urinary catheters get contaminated during the course of catheterization. Of the total 6 isolates, biofilm formation was seen in 100% Pseudomonas aeruginosa and E. coli, 90% in Enterococci, 80% in Klebsiella and 66% in S. aureus. It was noted that the biofilm production by Pseudomonas was prolonged by 7 days in amylase, 8 days in protease, 6 days in lysozyme, 7days in gentamycin and 5 days in EDTA treated catheter.
Abstract: This study was conducted published to investigate
there liability of the equation pressure-impulse (PI) reinforced
concrete column inprevious studies. Equation involves three different
levels of damage criteria known as D =0. 2, D =0. 5 and D =0. 8.The
damage criteria known as a minor when 0-0.2, 0.2-0.5is known as
moderate damage, high damage known as 0.5-0.8, and 0.8-1 of the
structure is considered a failure. In this study, two types of reliability
analyzes conducted. First, using pressure-impulse equation with
different parameters. The parameters involved are the concrete
strength, depth, width, and height column, the ratio of longitudinal
reinforcement and transverse reinforcement ratio. In the first analysis
of the reliability of this new equation is derived to improve the
previous equations. The second reliability analysis involves three
types of columns used to derive the PI curve diagram using the
derived equation to compare with the equation derived from other
researchers and graph minimum standoff versus weapon yield
Federal Emergency Management Agency (FEMA). The results
showed that the derived equation is more accurate with FEMA
standards than previous researchers.
Abstract: In this paper, gate leakage current has been mitigated
by the use of novel nanoscale MOSFET with Source/Drain-to-Gate
Non-overlapped and high-k spacer structure for the first time. A
compact analytical model has been developed to study the gate
leakage behaviour of proposed MOSFET structure. The result
obtained has found good agreement with the Sentaurus Simulation.
Fringing gate electric field through the dielectric spacer induces
inversion layer in the non-overlap region to act as extended S/D
region. It is found that optimal Source/Drain-to-Gate Non-overlapped
and high-k spacer structure has reduced the gate leakage current to
great extent as compared to those of an overlapped structure. Further,
the proposed structure had improved off current, subthreshold slope
and DIBL characteristic. It is concluded that this structure solves the
problem of high leakage current without introducing the extra series
resistance.
Abstract: This research evaluated and compared the thermodynamic performance of heat pump systems which can be run under two different modes as air to air and air to water by using only one compressor. To achieve this comparison an experimental performance study was made on a traditional vapor compressed heat pump system that can be run air to air mode and air to water mode by help of a valve. The experiments made under different thermal conditions. Thermodynamic performance of the systems are presented and compared with each other for different working conditions.
Abstract: The purpose of this research is to develop a security model for voice eavesdropping protection over digital networks. The proposed model provides an encryption scheme and a personal secret key exchange between communicating parties, a so-called voice data transformation system, resulting in a real-privacy conversation. The operation of this system comprises two main steps as follows: The first one is the personal secret key exchange for using the keys in the data encryption process during conversation. The key owner could freely make his/her choice in key selection, so it is recommended that one should exchange a different key for a different conversational party, and record the key for each case into the memory provided in the client device. The next step is to set and record another personal option of encryption, either taking all frames or just partial frames, so-called the figure of 1:M. Using different personal secret keys and different sets of 1:M to different parties without the intervention of the service operator, would result in posing quite a big problem for any eavesdroppers who attempt to discover the key used during the conversation, especially in a short period of time. Thus, it is quite safe and effective to protect the case of voice eavesdropping. The results of the implementation indicate that the system can perform its function accurately as designed. In this regard, the proposed system is suitable for effective use in voice eavesdropping protection over digital networks, without any requirements to change presently existing network systems, mobile phone network and VoIP, for instance.
Abstract: Erwinia carotovora var. carotovora is the main cause of soft rot in potatoes. Hyphaene thebaica was studied for biocontrol of E. carotovora which inhibited growth of E. carotovora on solid medium, a comparative study of classical and ultrasound-assisted extractions of Hyphaene thebaica fruit. The use of ultrasound decreased significant the total time of treatment and increase the total amount of crude extract. The crude extract was subjected to determine the in vitro, by a bioassay technique revealed that the treatment of paper disks with ultrasound extraction of Hyphaene thebaica reduced the growth of pathogen and produced inhibition zones up to 38mm in diameter. The antioxidant activity of ultrasound-ethanolic extract of Doum fruits (Hyphaene thebaica) was determined. Data obtained showed that the extract contains the secondary metabolites such as Tannins, Saponin, Flavonoids, Phenols, Steroids, Terpenoids, Glycosides and Alkaloids.
Abstract: Turbulence modeling of large-scale flow over a vegetated surface is complex. Such problems involve large scale computational domains, while the characteristics of flow near the surface are also involved. In modeling large scale flow, surface roughness including vegetation is generally taken into account by mean of roughness parameters in the modified law of the wall. However, the turbulence structure within the canopy region cannot be captured with this method, another method which applies source/sink terms to model plant drag can be used. These models have been developed and tested intensively but with a simple surface geometry. This paper aims to compare the use of roughness parameter, and additional source/sink terms in modeling the effect of plant drag on wind flow over a complex vegetated surface. The RNG k-ε turbulence model with the non-equilibrium wall function was tested with both cases. In addition, the k-ω turbulence model, which is claimed to be computationally stable, was also investigated with the source/sink terms. All numerical results were compared to the experimental results obtained at the study site Mason Bay, Stewart Island, New Zealand. In the near-surface region, it is found that the results obtained by using the source/sink term are more accurate than those using roughness parameters. The k-ω turbulence model with source/sink term is more appropriate as it is more accurate and more computationally stable than the RNG k-ε turbulence model. At higher region, there is no significant difference amongst the results obtained from all simulations.
Abstract: Hazardous Material transportation by road is coupled
with inherent risk of accidents causing loss of lives, grievous injuries,
property losses and environmental damages. The most common type
of hazmat road accident happens to be the releases (78%) of
hazardous substances, followed by fires (28%), explosions (14%) and
vapour/ gas clouds (6 %.).
The paper is discussing initially the probable 'Impact Zones'
likely to be caused by one flammable (LPG) and one toxic (ethylene
oxide) chemicals being transported through a sizable segment of a
State Highway connecting three notified Industrial zones in Surat
district in Western India housing 26 MAH industrial units. Three
'hotspots' were identified along the highway segment depending on
the particular chemical traffic and the population distribution within
500 meters on either sides. The thermal radiation and explosion
overpressure have been calculated for LPG / Ethylene Oxide BLEVE
scenarios along with toxic release scenario for ethylene oxide.
Besides, the dispersion calculations for ethylene oxide toxic release
have been made for each 'hotspot' location and the impact zones
have been mapped for the LOC concentrations. Subsequently, the
maximum Initial Isolation and the protective zones were calculated
based on ERPG-3 and ERPG-2 values of ethylene oxide respectively
which are estimated taking the worst case scenario under worst
weather conditions. The data analysis will be helpful to the local
administration in capacity building with respect to rescue /
evacuation and medical preparedness and quantitative inputs to
augment the District Offsite Emergency Plan document.
Abstract: Localized surface plasmon resonance (LSPR) is the
coherent oscillation of conductive electrons confined in noble
metallic nanoparticles excited by electromagnetic radiation, and
nanosphere lithography (NSL) is one of the cost-effective methods to
fabricate metal nanostructures for LSPR. NSL can be categorized
into two major groups: dispersed NSL and closely pack NSL. In
recent years, gold nanocrescents and gold nanoholes with vertical
sidewalls fabricated by dispersed NSL, and silver nanotriangles and
gold nanocaps on silica nanospheres fabricated by closely pack NSL,
have been reported for LSPR biosensing. This paper introduces
several novel gold nanostructures fabricated by NSL in LSPR
applications, including 3D nanostructures obtained by evaporating
gold obliquely on dispersed nanospheres, nanoholes with slant
sidewalls, and patchy nanoparticles on closely packed nanospheres,
all of which render satisfactory sensitivity for LSPR sensing. Since
the LSPR spectrum is very sensitive to the shape of the metal
nanostructures, formulas are derived and software is developed for
calculating the profiles of the obtainable metal nanostructures by
NSL, for different nanosphere masks with different fabrication
conditions. The simulated profiles coincide well with the profiles of
the fabricated gold nanostructures observed under scanning electron
microscope (SEM) and atomic force microscope (AFM), which
proves that the software is a useful tool for the process design of
different LSPR nanostructures.
Abstract: In this study, an ablation, mechanical and thermal properties of a rocket motor insulation from phenolic/ fiber matrix composites forming a laminate with different fiber between fiberglass and locally available synthetic fibers. The phenolic/ fiber matrix composites was mechanics and thermal properties by means of tensile strength, ablation, TGA and DSC. The design of thermal insulation involves several factors.Determined the mechanical properties according to MIL-I-24768: Density >1.3 g/cm3, Tensile strength >103 MPa and Ablation
Abstract: Thai language is difficult in all four language skills,
especially reading. The first year students may have different abilities
in reading, so a teacher is required to find out a student’s reading
level so that the teacher can help and support them till they can
develop and resolve each problem themselves. This research is aimed
to study the prosody problem among Thai students and will be
focused on first year Thai students in the second semester. A total of
58 students were involved in this study. Four obstacles were found:
1. Interpretation from what they read and write
2. Incorrectness Pronunciation of Prosody
3. Incorrectness in Rhythm of the Poem
4. Incorrectness of the Thai Poem Pronunciation
Abstract: Cement stabilization has been widely used for
improving the strength and stiffness of soft clayey soils. Cement
treated soil specimens used to investigate the stress-strain behaviour in
the laboratory study are usually cured for 7 days. This paper examines
the effects of curing time on the strength and stress strain behaviour of
cement treated marine clay under triaxial loading condition.
Laboratory-prepared cement treated Singapore marine clay with
different mix proportion S-C-W (soil solid-cement solid-water) and
curing time (7 days to 180 days) was investigated through conducting
unconfined compressive strength test and triaxial test. The results
show that the curing time has a significant effect on the unconfined
compressive strength u q , isotropic compression behaviour and stress
strain behaviour. Although the primary yield loci of the cement treated
soil specimens with the same mix proportion expand with curing time,
they are very narrowly banded and have nearly the same shape after
being normalized by isotropic compression primary stress '
py p . The
isotropic compression primary yield stress '
py p was shown to be
linearly related to unconfined compressive strength u q for specimens
with different curing time and mix proportion. The effect of curing
time on the hardening behaviour will diminish with consolidation
stress higher than isotropic compression primary yield stress but its
damping rate is dependent on the cement content.