Abstract: Carbon Fiber Reinforced Plastics (CFRPs) are widely
used for advanced applications, in particular in aerospace, automotive
and wind energy industries. Once cured to near net shape, CFRP
parts need several finishing operations such as trimming, milling or
drilling in order to accommodate fastening hardware and meeting the
final dimensions. The present research aims to study the effect of the
cutting temperature in trimming on the mechanical strength of high
performance CFRP laminates used for aeronautics applications. The
cutting temperature is of great importance when dealing with
trimming of CFRP. Temperatures higher than the glass-transition
temperature (Tg) of the resin matrix are highly undesirable: they
cause degradation of the matrix in the trimmed edges area, which can
severely affect the mechanical performance of the entire component.
In this study, a 9.50mm diameter CVD diamond coated carbide tool
with six flutes was used to trim 24-plies CFRP laminates. A
300m/min cutting speed and 1140mm/min feed rate were used in the
experiments. The tool was heated prior to trimming using a
blowtorch, for temperatures ranging from 20°C to 300°C. The
temperature at the cutting edge was measured using embedded KType
thermocouples. Samples trimmed for different cutting
temperatures, below and above Tg, were mechanically tested using
three-points bending short-beam loading configurations. New cutting
tools as well as worn cutting tools were utilized for the experiments.
The experiments with the new tools could not prove any correlation
between the length of cut, the cutting temperature and the mechanical
performance. Thus mechanical strength was constant, regardless of
the cutting temperature. However, for worn tools, producing a cutting
temperature rising up to 450°C, thermal damage of the resin was
observed. The mechanical tests showed a reduced mean resistance in
short beam configuration, while the resistance in three point bending
decreases with increase of the cutting temperature.
Abstract: Rapid prototyping is a new group of manufacturing
processes, which allows fabrication of physical of any complexity
using a layer by layer deposition technique directly from a computer
system. The rapid prototyping process greatly reduces the time and
cost necessary to bring a new product to market. The prototypes
made by these systems are used in a range of industrial application
including design evaluation, verification, testing, and as patterns for
casting processes. These processes employ a variety of materials and
mechanisms to build up the layers to build the part. The present work
was to build a FDM prototyping machine that could control the X-Y
motion and material deposition, to generate two-dimensional and
three-dimensional complex shapes. This study focused on the
deposition of wax material. This work was to find out the properties
of the wax materials used in this work in order to enable better
control of the FDM process. This study will look at the integration of
a computer controlled electro-mechanical system with the traditional
FDM additive prototyping process. The characteristics of the wax
were also analysed in order to optimise the model production process.
These included wax phase change temperature, wax viscosity and
wax droplet shape during processing.
Abstract: The ferrites ZnFe2O4, CdFe2O4 and CuFe2O4 are
synthesized in laboratory conditions using ceramic technology. Their
homogeneity and structure are proven by X-Ray diffraction analysis
and Mössbauer spectroscopy. The synthesized ferrites are subjected
to strong acid and high temperature leaching with solutions of H2SO4,
HCl and HNO3. The results indicate that the highest degree of
leaching of Zn, Cd and Cu from the ferrites is achieved by use of
HCl. The charging of five zinc sulfide concentrates was optimized using
the criterion of minimal amount of zinc ferrite produced when
roasting the concentrates in a fluidized bed. The results obtained are
interpreted in terms of the hydrometallurgical zinc production and
maximum recovery of zinc, copper and cadmium from initial zinc
concentrates after their roasting.
Abstract: The first layer of defense against data loss is the backup
data. This paper implements an agent-based network backup system
used the backup, server-storage and server-backup agent these
tripartite construction, and the snapshot and hierarchical index are
used in the NSBS. It realizes the control command and data flow
separation, balances the system load, thereby improving efficiency of
the system backup and recovery. The test results show the agent-based
network backup system can effectively improve the task-based
concurrency, reasonably allocate network bandwidth, the system
backup performance loss costs smaller and improves data recovery
efficiency by 20%.
Abstract: The aim of optimization of store management is not
only designing the situation of store management itself including its
equipment, technology and operation. In optimization of store
management we need to consider also synchronizing of
technological, transport, store and service operations throughout the
whole process of logistic chain in such a way that a natural flow of
material from provider to consumer will be achieved the shortest
possible way, in the shortest possible time in requested quality and
quantity and with minimum costs. The paper deals with the
application of the queuing theory for optimization of warehouse
processes. The first part refers to common information about the
problematic of warehousing and using mathematical methods for
logistics chains optimization. The second part refers to preparing a
model of a warehouse within queuing theory. The conclusion of the
paper includes two examples of using queuing theory in praxis.
Abstract: Dead wood and habitat tree such as fallen logs, snags,
stumps and cracks and loos bark etc. are regarded as an important
ecological component of forests on which many forest dwelling
species depend on presence of them within forest ecosystems.
Meanwhile its relation to management history in Caspian forest has
gone unreported. The aim of research was to compare the amounts of
dead wood and habitat trees in the forests with historically different
intensities of management, including: forests with the long term
implication of management (PS), the short term implication of
management (NS) which were compared with semi virgin forest
(GS). The number of 405 individual dead and habitat trees were
recorded and measured at 109 sampling locations. ANOVA revealed
volume of dead tree in the form and decay classes significantly differ
within sites and dead volume in the semi virgin forest significantly
higher than managed sites. Comparing the amount of dead and
habitat tree in three sites showed that, dead tree volume related with
management history and significantly differ in three study sites.
Meanwhile, frequency of habitat trees was significantly different
within sites. The highest amount of habitat trees including cavities,
cracks and loose bark and fork split trees was recorded in virgin site
and lowest recorded in the sites with the long term implication of
management. It can be concluded that forest management cause
reduction of the amount of dead and habitat tree specially in a large
size, thus managing this forest according to ecological sustainable
principles require a commitment to maintaining stand structure that
allow, continued generation of dead trees in a full range of size.
Abstract: In order to be capable of dealing with uncertainties,
subjectivities, including vagueness arising in building construction
projects, the application of fuzzy reasoning technique based on fuzzy
set theory is proposed. This study contributes significantly to the
development of a fuzzy reasoning safety risk assessment model for
building construction projects that could be employed to assess the
risk magnitude of each hazardous event identified during
construction, and a third parameter of probability of consequence is
incorporated in the model. By using the proposed safety risk analysis
methodology, more reliable and less ambiguities, which provide the
safety risk management project team for decision-making purposes.
Abstract: Friction stir welding and tungsten inert gas welding
techniques were employed to weld armor grade aluminum alloy to
investigate the effect of welding processes on tensile behavior of
weld joints. Tensile tests, Vicker microhardness tests and optical
microscopy were performed on developed weld joints and base metal.
Welding process influenced tensile behavior and microstructure of
weld joints. Friction stir welded joints showed tensile behavior better
than tungsten inert gas weld joints.
Abstract: One of the tasks of optical surveillance is to detect
anomalies in large amounts of image data. However, if the size of the
anomaly is very small, limited information is available to distinguish
it from the surrounding environment. Spectral detection provides a
useful source of additional information and may help to detect
anomalies with a size of a few pixels or less. Unfortunately, spectral
cameras are expensive because of the difficulty of separating two
spatial in addition to one spectral dimension. We investigate the
possibility of modifying a simple spectral line detector for outdoor
detection. This may be especially useful if the area of interest forms a
line, such as the horizon. We use a monochrome CCD that also
enables detection into the near infrared. A simple camera is attached
to the setup to determine which part of the environment is spectrally
imaged. Our preliminary results indicate that sensitive detection of
very small targets is indeed possible. Spectra could be taken from the
various targets by averaging columns in the line image. By imaging a
set of lines of various widths we found narrow lines that could not be
seen in the color image but remained visible in the spectral line
image. A simultaneous analysis of the entire spectra can produce
better results than visual inspection of the line spectral image. We are
presently developing calibration targets for spatial and spectral
focusing and alignment with the spatial camera. This will present
improved results and more use in outdoor application.
Abstract: This paper presents the influence of the vertical
seismic component on the non-linear dynamics analysis of three
different structures. The subject structures were analyzed and
designed according to recent codes. This paper considers three types
of buildings: 5-, 10-, and 15-story buildings. The non-linear
dynamics analysis of the structures with assuming elastic-perfectlyplastic
behavior was performed using RAM PERFORM-3D software;
the horizontal component was taken into consideration with and
without the incorporation of the corresponding vertical component.
Dynamic responses obtained for the horizontal component acting
alone were compared with those obtained from the simultaneous
application of both seismic components. The results show that the
effect of the vertical component of ground motion may increase the
axial load significantly in the interior columns and, consequently, the
stories. The plastic mechanisms would be changed. The P-Delta
effect is expected to increase. The punching base plate shear of the
columns should be considered. Moreover, the vertical component
increases the input energy when the structures exhibit inelastic
behavior and are taller.
Abstract: Automated Teller Machines (ATMs) can be
considered among one of the most important service facilities in the
banking industry. The investment in ATMs and the impact on the
banking industry is growing steadily in every part of the world. The
banks take into consideration many factors like safety, convenience,
visibility, and cost in order to determine the optimum locations of
ATMs. Today, ATMs are not only available in bank branches but
also at retail locations. Another important factor is the cash
management in ATMs. A cash demand model for every ATM is
needed in order to have an efficient cash management system. This
forecasting model is based on historical cash demand data which is
highly related to the ATMs location. So, the location and the cash
management problem should be considered together. This paper
provides a general review on studies, efforts and development in
ATMs location and cash management problem.
Abstract: This study aims at improving the urban hydrological
cycle of the Orléans agglomeration (France) and understanding the
relationship between physical and chemical parameters of urban
surface runoff and the hydrological conditions. In particular water
quality parameters such as pH, conductivity, total dissolved solids,
major dissolved cations and anions, and chemical and biological
oxygen demands were monitored for three types of urban water
discharges (wastewater treatment plant output (WWTP), storm
overflow and stormwater outfall) under two hydrologic scenarios (dry
and wet weather). The first results were obtained over a period of five
months. Each investigated (Ormes, l’Egoutier and La Corne) outfall
represents an urban runoff source that receives water from runoff
roads, gutters, the irrigation of gardens and other sources of flow over
the Earth’s surface that drains in its catchments and carries it to the
Loire River. In wet weather conditions there is rain water runoff and
an additional input from the roof gutters that have entered the
stormwater system during rainfall. For the comparison the results La
Chilesse is a storm overflow that was selected in our study as a
potential source of waste water which is located before the (WWTP). The comparison of the physical-chemical parameters (total
dissolved solids, turbidity, pH, conductivity, dissolved organic
carbon (DOC), concentration of major cations and anions) together
with the chemical oxygen demand (COD) and biological oxygen
demand (BOD) helped to characterize sources of runoff waters in the
different watersheds. It also helped to highlight the infiltration of
wastewater in some stormwater systems that reject directly in the
Loire River. The values of the conductivity measured in the outflow
of Ormes were always higher than those measured in the other two
outlets. The results showed a temporal variation for the Ormes outfall
of conductivity from 1465 μS cm-1 in the dry weather flow to 650 μS
cm-1 in the wet weather flow and also a spatial variation in the wet
weather flow from 650 μS cm-1 in the Ormes outfall to 281 μS cm-1
in L’Egouttier outfall. The ultimate BOD (BOD28) showed a
significant decrease in La Corne outfall from 181 mg L-1 in the wet
weather flow to 95 mg L-1 in the dry weather flow because of the
nutrient load that was transported by the runoff.
Abstract: With the increasing population and intensive land use,
huge traffic demand is generating worldwide both in developing and
developed countries. As a developing country, Bangladesh is also
facing the same problem in recent years by producing huge numbers
of daily trips. As a matter of fact, extensive traffic demand is
increasing day by day. Also, transport system in Dhaka is
heterogeneous, reflecting the heterogeneity in the socio-economic
and land use patterns. Trips produced here are for different purposes
such as work, business, educational etc. Due to the significant
concentration of educational institutions a large share of the trips are
generated by educational purpose. And one of the major percentages
of educational trips is produced by university going students and
most of them are travelled by car, bus, train, taxi, rickshaw etc. The
aim of the study was to find out the university students’ perception on
public transit ridership. A survey was conducted among 330 students
from eight different universities. It was found out that 26% of the
trips produced by university going students are travelled by public
bus service and only 5% are by train. Percentage of car share is 16%
and 12% of the trips are travelled by private taxi. It has been
observed from the study, students those who prefer bus instead of
other options, 42 percent of their family resides outside Dhaka. And
those who prefer walking, of them, over 40 percent students’ family
reside outside of Dhaka and of them over 85 percent students have a
tendency to live in a mess. On the contrary, students travelling by car
represents, most of their family reside in Dhaka. The study also
revealed that the most important reason that restricts students not to
use public transit is poor service. Negative attitudes such as
discomfort, uneasiness in using public transit also reduces the usage
of public transit. The poor waiting area is another major cause of not
using public transit. Insufficient security also plays a significant role
in not using public transit. On the contrary, the fare is not a problem
for students those who use public transit as a mode of transportation.
Students also think stations are not far away from their home or
institution and they do not need to wait long for the buses or trains. It
was also found accessibility to public transit is moderate.
Abstract: An integrated modeling approach was used in this study for energy planning and climate change mitigation assessment. The main objective of this study was to develop various green-house gas (GHG) mitigations scenarios in the energy demand and supply sectors for the state of Florida. The Long range energy alternative planning (LEAP) model was used in this study to examine the energy alternative and GHG emissions reduction scenarios for short and long term (2010-2050). One of the energy analysis and GHG mitigation scenarios was developed by taking into account the available renewable energy resources potential for power generation in the state of Florida. This will help to compare and analyze the GHG reduction measure against “Business As Usual” and ‘State of Florida Policy” scenarios. Two master scenarios: “Electrification” and “Energy efficiency and Lifestyle” were developed through combination of various mitigation scenarios: technological changes and energy efficiency and conservation. The results show a net reduction of the energy demand and GHG emissions by adopting these two energy scenarios compared to the business as usual.
Abstract: The market competition is moving from the single
firm to the whole supply chain because of increasing competition and
growing need for operational efficiencies and customer orientation.
Supply chain management allows companies to look beyond their
organizational boundaries to develop and leverage resources and
capabilities of their supply chain partners. This creates competitive
advantages in the marketplace and because of this SCM has acquired
strategic importance. Lean Approach is a management strategy that focuses on reducing
every type of waste present in an organization. This approach is
becoming more and more popular among supply chain managers. The supply chain application of lean approach is not frequent. In
particular, it is not well studied which are the impacts of lean
approach principles in a supply chain context. In literature there are
only few studies aimed at understanding the qualitative impact of the
lean approach in supply chains. Therefore, the goal of this research
work is to study the impacts of lean principles implementation along
a supply chain. To achieve this, a simulation model of a threeechelon
multi-product supply chain has been built. Kanban system (and several priority policies) and setup time
reduction degrees are implemented in the lean-configured supply
chain to apply pull and lot-sizing decrease principles respectively. To
evaluate the benefits of lean approach, lean supply chain is compared
with an EOQ-configured supply chain. The simulation results show
that Kanban system and setup-time reduction improve inventory
stock level. They also show that logistics efforts are affected to lean
implementation degree. The paper concludes describing
performances of lean supply chain in different contexts.
Abstract: Optimizing the parameters in the controller plays a
vital role in the control theory and its applications. Optimizing the
PID parameters is finding out the best value from the feasible
solutions. Finding the optimal value is an optimization problem.
Inverted Pendulum is a very good platform for control engineers to
verify and apply different logics in the field of control theory. It is
necessary to find an optimization technique for the controller to tune
the values automatically in order to minimize the error within the
given bounds. In this paper, the algorithmic concepts of Harmony
search (HS) and Genetic Algorithm (GA) have been analyzed for the
given range of values. The experimental results show that HS
performs well than GA.
Abstract: The present explanatory study concerns with the
relation between Diabetes Mellitus and Food Balance in the Kingdom
of Saudi Arabia during 2005-2010, using published data. Results illustrated that Saudi citizen daily protein consumption
(DPC) during 2005-2007 (g/capita/day) is higher than the average
global consumption level of protein with 15.27%, daily fat
consumption (DFC) with 24.56% and daily energy consumption
(DEC) with 16.93% and increases than recommended level by
International Nutrition Organizations (INO) with 56% for protein,
60.49% for fat and 27.37% for energy. On the other hand, DPC per
capita in Saudi Arabia decreased during the period 2008-2010 from
88.3 to 82.36 gram/ day. Moreover, DFC per capita in Saudi Arabia
decreased during the period 2008-2010 from 3247.90 to 3176.43
Cal/capita/ day, and daily energy consumption (DEC) of Saudi
citizen increases than world consumption with 16.93%, whereas
increases with 27.37% than INO. Despite this, DPC, DFC and DEC
per capita in Saudi Arabia still higher than world mean. On the other
side, results illustrated that the number of diabetic patients in Saudi
Arabia during the same period (2005-2010). The curve of diabetic
patient’s number in Saudi Arabia during 2005-2010 is regular
ascending with increasing level ranged between 7.10% in 2005 and
12.44% in 2010. It is essential to devise Saudi National programs to educate the
public about the relation of food balances and diabetes so it could be
avoided, and provide citizens with healthy dietary balances tables.
Abstract: Objectives: To determine the nutritional status and
risk factors associated with women practicing geophagia in QwaQwa,
South Africa. Materials and Methods: An observational epidemiological study
design was adopted which included an exposed (geophagia) and nonexposed
(control) group. A food frequency questionnaire, anthropometric measurements and blood sampling were applied to
determine nutritional status of participants. Logistic regression
analysis was performed in order to identify factors that were likely to
be associated with the practice of geophagia. Results: The mean total energy intake for the geophagia group (G)
and control group (C) were 10324.31 ± 2755.00 kJ and 10763.94 ±
2556.30 kJ respectively. Both groups fell within the overweight
category according to the mean Body Mass Index (BMI) of each
group (G= 25.59 kg/m2; C= 25.14 kg/m2). The mean serum iron
levels of the geophagia group (6.929 μmol/l) were significantly lower
than that of the control group (13.75 μmol/l) (p = 0.000). Serum
transferrin (G=3.23g/l; C=2.7054g/l) and serum transferrin saturation
(G=8.05%; C=18.74%) levels also differed significantly between
groups (p=0.00). Factors that were associated with the practice of
geophagia included haemoglobin (Odds ratio (OR):14.50), serumiron
(OR: 9.80), serum-ferritin (OR: 3.75), serum-transferrin (OR:
6.92) and transferrin saturation (OR: 14.50). A significant negative
association (p=0.014) was found between women who were wageearners
and those who were not wage-earners and the practice of
geophagia (OR: 0.143; CI: 0.027; 0.755). These findings seem to
indicate that a permanent income may decrease the likelihood of
practising geophagia. Key Findings: Geophagia was confirmed to be a risk factor for
iron deficiency in this community. The significantly strong
association between geophagia and iron deficiency emphasizes the
importance of identifying the practice of geophagia in women,
especially during their child bearing years.
Abstract: Zinc borate is an important inorganic hydrate borate
material, which can be used as a flame retardant agent and corrosion
resistance material. This compound can loss its structural water
content at higher than 290°C. Due to thermal stability; Zinc Borate
can be used as flame retardant at high temperature process of plastic
and gum. In this study, the ultrasonic reaction of zinc borates were
studied using hydrozincite (Zn5(CO3)2·(OH)6) and boric acid
(H3BO3) raw materials. Before the synthesis raw materials were
characterized by X-Ray Diffraction (XRD) and Fourier Transform
Infrared Spectroscopy (FT-IR). Ultrasonic method is a new
application on the zinc borate synthesis. The synthesis parameters
were set to 90°C reaction temperature and 55 minutes of reaction
time, with 1:1, 1:2, 1:3, 1:4 and 1:5 molar ratio of starting materials
(Zn5(CO3)2·(OH)6 : H3BO3). After the zinc borate synthesis, the
products were analyzed by XRD and FT-IR. As a result, optimum
molar ratio of 1:5 is determined for the synthesis of zinc borates with
ultrasonic method.
Abstract: Multiple Input Multiple Output (MIMO) systems are
wireless systems with multiple antenna elements at both ends of the
link. Wireless communication systems demand high data rate and
spectral efficiency with increased reliability. MIMO systems have
been popular techniques to achieve these goals because increased
data rate is possible through spatial multiplexing scheme and
diversity. Spatial Multiplexing (SM) is used to achieve higher
possible throughput than diversity. In this paper, we propose a Zero-
Forcing (ZF) detection using a combination of Ordered Successive
Interference Cancellation (OSIC) and Zero Forcing using
Interference Cancellation (ZF-IC). The proposed method used an
OSIC based on Signal to Noise Ratio (SNR) ordering to get the
estimation of last symbol, then the estimated last symbol is
considered to be an input to the ZF-IC. We analyze the Bit Error Rate
(BER) performance of the proposed MIMO system over Rayleigh
Fading Channel, using Binary Phase Shift Keying (BPSK)
modulation scheme. The results show better performance than the
previous methods.