Abstract: The main focus of the work was concerned with hydrodynamic and thermal analysis of the plate heat exchanger channel with corrugation patterns suggested to be triangular, sinusoidal, and square corrugation. This study was to numerically model and validate the triangular corrugated channel with dimensions/parameters taken from open literature, and then model/analyze both sinusoidal, and square corrugated channel referred to the triangular model. Initially, 2D modeling with local extensive analysis for triangular corrugated channel was carried out. By that, all local pressure drop, wall shear stress, friction factor, static temperature, heat flux, Nusselt number, and surface heat coefficient, were analyzed to interpret the hydrodynamic and thermal phenomena occurred in the flow. Furthermore, in order to facilitate confidence in this model, a comparison between the values predicted, and experimental results taken from literature for almost the same case, was done. Moreover, a holistic numerical study for sinusoidal and square channels together with global comparisons with triangular corrugation under the same condition, were handled. Later, a comparison between electric, and fluid cooling through varying the boundary condition was achieved. The constant wall temperature and constant wall heat flux boundary conditions were employed, and the different resulted Nusselt numbers as a consequence were justified. The results obtained can be used to come up with an optimal design, a 'compromise' between heat transfer and pressure drop.
Abstract: This paper addresses issues of integral steering of
vehicles with two steering axles, where the rear wheels are pivoted in
the direction of the front wheels, but also in the opposite direction.
The steering box of the rear axle is presented with simple linkages
(single contour) that correlate the pivoting of the rear wheels
according to the direction of the front wheels, respectively to the
rotation angle of the steering wheel. The functionality of the system
is analyzed – the extent to which the requirements of the integral
steering are met by the considered/proposed mechanisms. The paper
highlights the quality of the single contour linkages, with two driving
elements for meeting these requirements, emphasizing diagrams of
mechanisms with 2 driving elements. Cam variants are analyzed and
proposed for the rear axle steering box. Cam profiles are determined
by various factors.
Abstract: The study of the transport coefficients in electronic
devices is currently carried out by analytical and empirical models.
This study requires several simplifying assumptions, generally
necessary to lead to analytical expressions in order to study the
different characteristics of the electronic silicon-based devices.
Further progress in the development, design and optimization of
Silicon-based devices necessarily requires new theory and modeling
tools. In our study, we use the PSO (Particle Swarm Optimization)
technique as a computational tool to develop analytical approaches in
order to study the transport phenomenon of the electron in crystalline
silicon as function of temperature and doping concentration. Good
agreement between our results and measured data has been found.
The optimized analytical models can also be incorporated into the
circuits simulators to study Si-based devices without impact on the
computational time and data storage.
Abstract: The algorithm represents the DCT coefficients to concentrate signal energy and proposes combination and dictator to eliminate the correlation in the same level subband for encoding the DCT-based images. This work adopts DCT and modifies the SPIHT algorithm to encode DCT coefficients. The proposed algorithm also provides the enhancement function in low bit rate in order to improve the perceptual quality. Experimental results indicate that the proposed technique improves the quality of the reconstructed image in terms of both PSNR and the perceptual results close to JPEG2000 at the same bit rate.
Abstract: This paper proposes a modeling methodology for the
development of data analysis solution. The Author introduce the
approach to address data warehousing issues at the at enterprise level.
The methodology covers the process of the requirements eliciting and
analysis stage as well as initial design of data warehouse. The paper
reviews extended business process model, which satisfy the needs of
data warehouse development. The Author considers that the use of
business process models is necessary, as it reflects both enterprise
information systems and business functions, which are important for
data analysis. The Described approach divides development into
three steps with different detailed elaboration of models. The
Described approach gives possibility to gather requirements and
display them to business users in easy manner.
Abstract: The influence of axial magnetic field (B=0.48 T) on
the variation of ionization efficiency coefficient h and secondary
electron emission coefficient g with respect to reduced electric field
E/P is studied at a new range of plane-parallel electrode spacing (0<
d< 20 cm) and different nitrogen working pressure between 0.5-20
Pa. The axial magnetic field is produced from an inductive copper
coil of radius 5.6 cm. The experimental data of breakdown voltage is
adopted to estimate the mean Paschen curves at different working
features. The secondary electron emission coefficient is calculated
from the mean Paschen curve and used to determine the minimum
breakdown voltage. A reduction of discharge voltage of about 25% is
investigated by the applied of axial magnetic field. At high interelectrode
spacing, the effect of axial magnetic field becomes more
significant for the obtained values of h but it was less for the values
of g.
Abstract: In designing of condensers, the prediction of pressure
drop is as important as the prediction of heat transfer coefficient.
Modeling of two phase flow, particularly liquid – vapor flow under
diabatic conditions inside a horizontal tube using CFD analysis is
difficult with the available two phase models in FLUENT due to
continuously changing flow patterns. In the present analysis, CFD
analysis of two phase flow of refrigerants inside a horizontal tube of
inner diameter, 0.0085 m and 1.2 m length is carried out using
homogeneous model under adiabatic conditions. The refrigerants
considered are R22, R134a and R407C. The analysis is performed at
different saturation temperatures and at different flow rates to
evaluate the local frictional pressure drop. Using Homogeneous
model, average properties are obtained for each of the refrigerants
that is considered as single phase pseudo fluid. The so obtained
pressure drop data is compared with the separated flow models
available in literature.
Abstract: This paper presents the experimental results of a
single cylinder Enfield engine using an electronically controlled fuel
injection system which was developed to carry out exhaustive tests
using neat CNG, and mixtures of hydrogen in compressed natural gas
(HCNG) as 0, 5, 10, 15 and 20% by energy. Experiments were
performed at 2000 and 2400 rpm with wide open throttle and varying
the equivalence ratio. Hydrogen which has fast burning rate, when
added to compressed natural gas, enhances its flame propagation rate.
The emissions of HC, CO, decreased with increasing percentage of
hydrogen but NOx was found to increase. The results indicated a
marked improvement in the brake thermal efficiency with the
increase in percentage of hydrogen added. The improved thermal
efficiency was clearly observed to be more in lean region as
compared to rich region. This study is expected to reduce vehicular
emissions along with increase in thermal efficiency and thus help in
reduction of further environmental degradation.
Abstract: carbonylation of methanol in homogenous phase is
one of the major routesfor production of acetic acid. Amongst group
VIII metal catalysts used in this process iridium has displayed the
best capabilities. To investigate effect of operating parameters like:
temperature, pressure, methyl iodide, methyl acetate, iridium,
ruthenium, and water concentrations on the reaction rate,
experimental design for this system based upon central composite
design (CCD) was utilized. Statistical rate equation developed by this
method contained individual, interactions and curvature effects of
parameters on the reaction rate. The model with p-value less than
0.0001 and R2 values greater than 0.9; confirmeda satisfactory fitness
of the experimental and theoretical studies. In other words, the
developed model and experimental data obtained passed all
diagnostic tests establishing this model as a statistically significant.
Abstract: Multimedia information availability has increased
dramatically with the advent of video broadcasting on handheld
devices. But with this availability comes problems of maintaining the
security of information that is displayed in public. ISMA Encryption
and Authentication (ISMACryp) is one of the chosen technologies for
service protection in DVB-H (Digital Video Broadcasting-
Handheld), the TV system for portable handheld devices. The
ISMACryp is encoded with H.264/AVC (advanced video coding),
while leaving all structural data as it is. Two modes of ISMACryp are
available; the CTR mode (Counter type) and CBC mode (Cipher
Block Chaining) mode. Both modes of ISMACryp are based on 128-
bit AES algorithm. AES algorithms are more complex and require
larger time for execution which is not suitable for real time
application like live TV. The proposed system aims to gain a deep
understanding of video data security on multimedia technologies and
to provide security for real time video applications using selective
encryption for H.264/AVC. Five level of security proposed in this
paper based on the content of NAL unit in Baseline Constrain profile
of H.264/AVC. The selective encryption in different levels provides
encryption of intra-prediction mode, residue data, inter-prediction
mode or motion vectors only. Experimental results shown in this
paper described that fifth level which is ISMACryp provide higher
level of security with more encryption time and the one level provide
lower level of security by encrypting only motion vectors with lower
execution time without compromise on compression and quality of
visual content. This encryption scheme with compression process
with low cost, and keeps the file format unchanged with some direct
operations supported. Simulation was being carried out in Matlab.
Abstract: This paper addresses one important aspect of
combustion system analysis, the spray evaporation and
dispersion modeling. In this study we assume an empty
cylinder which is as a simulator for a ramjet engine and the
cylinder has been studied by cold flow. Four nozzles have the
duties of injection which are located in the entrance of
cylinder. The air flow comes into the cylinder from one side
and injection operation will be done. By changing injection
velocity and entrance air flow velocity, we have studied
droplet sizing and efficient mass fraction of fuel vapor near
and at the exit area. We named the mass of fuel vapor inside
the flammability limit as the efficient mass fraction. Further,
we decreased the initial temperature of fuel droplets and we
have repeated the investigating again. To fulfill the calculation
we used a modified version of KIVA-3V.
Abstract: Experimental data from an atmospheric air/water terrain slugging case has been made available by the Shell Amsterdam research center, and has been subject to numerical simulation and comparison with a one-dimensional two-phase slug tracking simulator under development at the Norwegian University of Science and Technology. The code is based on tracking of liquid slugs in pipelines by use of a Lagrangian grid formulation implemented in Cµ by use of object oriented techniques. An existing hybrid spatial discretization scheme is tested, in which the stratified regions are modelled by the two-fluid model. The slug regions are treated incompressible, thus requiring a single momentum balance over the whole slug. Upon comparison with the experimental data, the period of the simulated severe slugging cycle is observed to be sensitive to slug generation in the horizontal parts of the system. Two different slug initiation methods have been tested with the slug tracking code, and grid dependency has been investigated.
Abstract: Decision fusion is one of hot research topics in
classification area, which aims to achieve the best possible
performance for the task at hand. In this paper, we
investigate the usefulness of this concept to improve change
detection accuracy in remote sensing. Thereby, outputs of
two fuzzy change detectors based respectively on
simultaneous and comparative analysis of multitemporal
data are fused by using fuzzy integral operators. This
method fuses the objective evidences produced by the
change detectors with respect to fuzzy measures that express
the difference of performance between them. The proposed
fusion framework is evaluated in comparison with some
ordinary fuzzy aggregation operators. Experiments carried
out on two SPOT images showed that the fuzzy integral was
the best performing. It improves the change detection
accuracy while attempting to equalize the accuracy rate in
both change and no change classes.
Abstract: In this paper, the implementation of a rule-based
intuitive reasoner is presented. The implementation included two
parts: the rule induction module and the intuitive reasoner. A large
weather database was acquired as the data source. Twelve weather
variables from those data were chosen as the “target variables"
whose values were predicted by the intuitive reasoner. A “complex"
situation was simulated by making only subsets of the data available
to the rule induction module. As a result, the rules induced were
based on incomplete information with variable levels of certainty.
The certainty level was modeled by a metric called "Strength of
Belief", which was assigned to each rule or datum as ancillary
information about the confidence in its accuracy. Two techniques
were employed to induce rules from the data subsets: decision tree
and multi-polynomial regression, respectively for the discrete and the
continuous type of target variables. The intuitive reasoner was tested
for its ability to use the induced rules to predict the classes of the
discrete target variables and the values of the continuous target
variables. The intuitive reasoner implemented two types of
reasoning: fast and broad where, by analogy to human thought, the
former corresponds to fast decision making and the latter to deeper
contemplation. . For reference, a weather data analysis approach
which had been applied on similar tasks was adopted to analyze the
complete database and create predictive models for the same 12
target variables. The values predicted by the intuitive reasoner and
the reference approach were compared with actual data. The intuitive
reasoner reached near-100% accuracy for two continuous target
variables. For the discrete target variables, the intuitive reasoner
predicted at least 70% as accurately as the reference reasoner. Since
the intuitive reasoner operated on rules derived from only about 10%
of the total data, it demonstrated the potential advantages in dealing
with sparse data sets as compared with conventional methods.
Abstract: In this work, we apply the Modified Laplace
decomposition algorithm in finding a numerical solution of Blasius’
boundary layer equation for the flat plate in a uniform stream. The
series solution is found by first applying the Laplace transform to the
differential equation and then decomposing the nonlinear term by the
use of Adomian polynomials. The resulting series, which is exactly the
same as that obtained by Weyl 1942a, was expressed as a rational
function by the use of diagonal padé approximant.
Abstract: Knowledge is attributed to human whose problemsolving
behavior is subjective and complex. In today-s knowledge
economy, the need to manage knowledge produced by a community
of actors cannot be overemphasized. This is due to the fact that
actors possess some level of tacit knowledge which is generally
difficult to articulate. Problem-solving requires searching and sharing
of knowledge among a group of actors in a particular context.
Knowledge expressed within the context of a problem resolution
must be capitalized for future reuse. In this paper, an approach that
permits dynamic capitalization of relevant and reliable actors-
knowledge in solving decision problem following Economic
Intelligence process is proposed. Knowledge annotation method and
temporal attributes are used for handling the complexity in the
communication among actors and in contextualizing expressed
knowledge. A prototype is built to demonstrate the functionalities of
a collaborative Knowledge Management system based on this
approach. It is tested with sample cases and the result showed that
dynamic capitalization leads to knowledge validation hence
increasing reliability of captured knowledge for reuse. The system
can be adapted to various domains.
Abstract: The direct implementation of interleaver functions
in WiMAX is not hardware efficient due to presence of complex
functions. Also the conventional method i.e. using memories for
storing the permutation tables is silicon consuming. This work
presents a 2-D transformation for WiMAX channel interleaver
functions which reduces the overall hardware complexity to
compute the interleaver addresses on the fly. A fully reconfigurable
architecture for address generation in WiMAX
channel interleaver is presented, which consume 1.1 k-gates in
total. It can be configured for any block size and any modulation
scheme in WiMAX. The presented architecture can run at a
frequency of 200 MHz, thus fully supporting high bandwidth
requirements for WiMAX.
Abstract: Saudi Arabia in recent years has seen drastic increase
in traffic related crashes. With population of over 29 million, Saudi
Arabia is considered as a fast growing and emerging economy. The
rapid population increase and economic growth has resulted in rapid
expansion of transportation infrastructure, which has led to increase
in road crashes. Saudi Ministry of Interior reported more than 7,000
people killed and 68,000 injured in 2011 ranking Saudi Arabia to be
one of the worst worldwide in traffic safety. The traffic safety issues
in the country also result in distress to road users and cause and
economic loss exceeding 3.7 billion Euros annually. Keeping this in
view, the researchers in Saudi Arabia are investigating ways to
improve traffic safety conditions in the country. This paper presents a
multilevel approach to collect traffic safety related data required to do
traffic safety studies in the region. Two highway corridors including
King Fahd Highway 39 kilometre and Gulf Cooperation Council
Highway 42 kilometre long connecting the cities of Dammam and
Khobar were selected as a study area. Traffic data collected included
traffic counts, crash data, travel time data, and speed data. The
collected data was analysed using geographic information system to
evaluate any correlation. Further research is needed to investigate the
effectiveness of traffic safety related data when collected in a
concerted effort.
Abstract: A new design of a planar passive T-micromixer with fin-shaped baffles in the mixing channel is presented. The mixing efficiency and the level of pressure loss in the channel have been investigated by numerical simulations in the range of Reynolds number (Re) 1 to 50. A Mixing index (Mi) has been defined to quantify the mixing efficiency, which results over 85% at both ends of the Re range, what demonstrates the micromixer can enhance mixing using the mechanisms of diffusion (lower Re) and convection (higher Re). Three geometric dimensions: radius of baffle, baffles pitch and height of the channel define the design parameters, and the mixing index and pressure loss are the performance parameters used to optimize the micromixer geometry with a multi-criteria optimization method. The Pareto front of designs with the optimum trade-offs, maximum mixing index with minimum pressure loss, is obtained. Experiments for qualitative and quantitative validation have been implemented.
Abstract: Based on assumptions of neo-classical economics and
rational choice / public choice theory, this paper investigates the
regulation of industrial land use in Taiwan by homeowners
associations (HOAs) as opposed to traditional government
administration. The comparison, which applies the transaction cost
theory and a polynomial regression analysis, manifested that HOAs
are superior to conventional government administration in terms of
transaction costs and overall efficiency. A case study that compares
Taiwan-s commonhold industrial park, NangKang Software Park, to
traditional government counterparts using limited data on the costs
and returns was analyzed. This empirical study on the relative
efficiency of governmental and private institutions justified the
important theoretical proposition. Numerical results prove the
efficiency of the established model.