Abstract: The present work attempts to investigate the
combustion, performance and emission characteristics of an existing
single-cylinder four-stroke compression-ignition engine operated in
dual-fuel mode with hydrogen as an alternative fuel. Environmental
concerns and limited amount of petroleum fuels have caused interests
in the development of alternative fuels like hydrogen for internal
combustion (IC) engines. In this experimental investigation, a diesel
engine is made to run using hydrogen in dual fuel mode with diesel,
where hydrogen is introduced into the intake manifold using an LPGCNG
injector and pilot diesel is injected using diesel injectors. A
Timed Manifold Injection (TMI) system has been developed to vary
the injection strategies. The optimized timing for the injection of
hydrogen was 10^0 CA after top dead center (ATDC). From the study
it was observed that with increasing hydrogen rate, enhancement in
brake thermal efficiency (BTHE) of the engine has been observed
with reduction in brake specific energy consumption (BSEC).
Furthermore, Soot contents decrease with an increase in indicated
specific NOx emissions with the enhancement of hydrogen flow rate.
Abstract: In recent years, there have been attempts to store
natural gas in adsorptive form. This is called adsorptive natural gas,
or ANG. The problem with this technology is the low sorption
capacity. The purpose is to achieve compressed natural gas (CNG)
capacity of 230 V/V. Further research is required to achieve such
target. Several research studies have been performed with this target;
through either the modification or development of new sorbents or
the optimization of the operation sorption process itself. In this work,
storage of methane on molecular sieves 5A and 13X was studied on
dry basis, and on wet basis to certain extent. The temperature and the
pressure dynamics were investigated. The results indicated that
regardless of the charge pressure, the time for the peak temperature
during the methane charge process is always the same. This can be
used as a characteristic of the adsorbent. The total achieved
deliveries using molecular sieves were much lower than that of
activated carbons; 53.0 V/V for the case of 13X molecular sieves and
43 V/V for the case of 5A molecular sieves, both at 2oC and 4 MPa
(580 psi). Investigation of charge pressure dynamic using wet
molecular sieves at 2oC and a mass ratio of 0.5, revealed slowness of
the process and unexpected behavior.
Abstract: This paper puts forward one kind of air-fuel ratio
control method with PI controller. With the help of
MATLAB/SIMULINK software, the mathematical model of air-fuel
ratio control system for distributorless CNG engine is constructed.
The objective is to maintain cylinder-to-cylinder air-fuel ratio at a
prescribed set point, determined primarily by the state of the Three-
Way-Catalyst (TWC), so that the pollutants in the exhaust are
removed with the highest efficiency. The concurrent control of airfuel
under transient conditions could be implemented by Proportional
and Integral (PI) controller. The simulation result indicates that the
control methods can easily eliminate the air/fuel maldistribution and
maintain the air/fuel ratio at the stochiometry within minimum
engine events.
Abstract: This paper presents the experimental results of a
single cylinder Enfield engine using an electronically controlled fuel
injection system which was developed to carry out exhaustive tests
using neat CNG, and mixtures of hydrogen in compressed natural gas
(HCNG) as 0, 5, 10, 15 and 20% by energy. Experiments were
performed at 2000 and 2400 rpm with wide open throttle and varying
the equivalence ratio. Hydrogen which has fast burning rate, when
added to compressed natural gas, enhances its flame propagation rate.
The emissions of HC, CO, decreased with increasing percentage of
hydrogen but NOx was found to increase. The results indicated a
marked improvement in the brake thermal efficiency with the
increase in percentage of hydrogen added. The improved thermal
efficiency was clearly observed to be more in lean region as
compared to rich region. This study is expected to reduce vehicular
emissions along with increase in thermal efficiency and thus help in
reduction of further environmental degradation.
Abstract: This paper presents an environmental and technoeconomic
evaluation of light duty vehicles in Iran. A comprehensive
well-to-wheel (WTW) analysis is applied to compare different
automotive fuel chains, conventional internal combustion engines and
innovative vehicle powertrains. The study examines the
competitiveness of 15 various pathways in terms of energy
efficiencies, GHG emissions, and levelized cost of different energy
carriers. The results indicate that electric vehicles including battery
electric vehicles (BEV), fuel cell vehicles (FCV) and plug-in hybrid
electric vehicles (PHEV) increase the WTW energy efficiency by
54%, 51% and 46%, respectively, compared to common internal
combustion engines powered by gasoline. On the other hand,
greenhouse gas (GHG) emissions per kilometer of FCV and BEV
would be 48% lower than that of gasoline engines. It is concluded
that BEV has the lowest total cost of energy consumption and
external cost of emission, followed by internal combustion engines
(ICE) fueled by CNG. Conventional internal combustion engines
fueled by gasoline, on the other hand, would have the highest costs.
Abstract: The present study deals with the analysis of the cylindrical part of a CNG storage vessel, combining a plastic liner and an over wrapped filament wound composite. Three kind of polymer are used in the present analysis: High density Polyethylene HDPE, Light low density Polyethylene LLDPE and finally blend of LLDPE/HDPE. The effect of the mechanical properties on the behavior of type IV vessel may be then investigated. In the present paper, the effect of the order of the circumferential winding on the stacking sequence may be then investigated. Based on mechanical considerations, the present model provides an exact solution for stresses and deformations on the cylindrical section of the vessel under thermo-mechanical static loading. The result show a good behavior of HDPE liner compared to the other plastic materials. The presence of circumferential winding angle in the stacking improves the rigidity of vessel by improving the burst pressure.