Abstract: Aluminum alloy sheets have several advantages such
as the lightweight, high-specific strength and recycling efficiency.
Therefore, aluminum alloy sheets in sheet forming have been used in various areas as automotive components and so forth. During the
process of sheet forming, wrinkling which is caused by compression stress might occur and the formability of sheets was affected by
occurrence of wrinkling. A few studies of uniaxial compressive test by
using square tubes, pipes and sheets were carried out to clarify the each wrinkling behavior. However, on uniaxial compressive test,
deformation behavior of the sheets hasn-t be cleared. Then, it is necessary to clarify the relationship between the buckling behavior
and the forming conditions. In this study, the effect of dimension of the sheet in the buckling behavior on compression test of aluminum alloy sheet was cleared by experiment and FEA. As the results, the buckling
deformation was classified by three modes in terms of the distribution of equivalent plastic strain.
Abstract: This paper is a simple and systematic approaches to the design and analysis a pulse width modulation (PWM) based sliding mode controller for buck DC-DC Converters. Various aspects of the design, including the practical problems and the proposed solutions, are detailed. However, these control strategies can't compensate for large load current and input voltage variations. In this paper, a new control strategy by compromising both schemes advantages and avoiding their drawbacks is proposed, analyzed and simulated.
Abstract: In this paper, a method based on Non-Dominated
Sorting Genetic Algorithm (NSGA) has been presented for the Volt /
Var control in power distribution systems with dispersed generation
(DG). Genetic algorithm approach is used due to its broad
applicability, ease of use and high accuracy. The proposed method is
better suited for volt/var control problems. A multi-objective
optimization problem has been formulated for the volt/var control of
the distribution system. The non-dominated sorting genetic algorithm
based method proposed in this paper, alleviates the problem of tuning
the weighting factors required in solving the multi-objective volt/var
control optimization problems. Based on the simulation studies
carried out on the distribution system, the proposed scheme has been
found to be simple, accurate and easy to apply to solve the multiobjective
volt/var control optimization problem of the distribution
system with dispersed generation.
Abstract: The main objective of this paper is to provide an efficient tool for delineating brain tumors in three-dimensional magnetic resonance images and set up compression-transmit schemes to distribute result to the remote doctor. To achieve this goal, we use basically a level-sets approach to delineating brain tumors in threedimensional. Then introduce a new compression and transmission plan of 3D brain structures based for the meshes simplification, adapted for time to the specific needs of the telemedicine and to the capacities restricted by wireless network communication. We present here the main stages of our system, and preliminary results which are very encouraging for clinical practice.
Abstract: A climate dependent model is proposed to simulate
the population of Aedes aegypti mosquito. In developing the model,
average temperature of Shah Alam, Malaysia was used to determine
the development rate of each stage of the life cycle of mosquito.
Rainfall dependent function was proposed to simulate the hatching
rate of the eggs under several assumptions. The proposed transition
matrix was obtained and used to simulate the population of eggs,
larvae, pupae and adults mosquito. It was found that the peak of
mosquito abundance comes during a relatively dry period following a
heavy rainfall. In addition, lag time between the peaks of mosquito
abundance and dengue fever cases in Shah Alam was estimated.
Abstract: This paper presents the theoretical investigation of a
slotted patch antenna. The main objective of proposed work is to
obtain a large bandwidth antenna with reduced size. The antenna has
a compact size of 21.1mm x 20.25mm x 8.5mm. Two designs with
minor variation are studied which provide wide impedance
bandwidths of 24.056% and 25.63% respectively with the use of
parasitic elements when excited by a probe feed. The advantages of
this configuration are its compact size and the wide range of
frequencies covered. A parametric study is also conducted to
investigate the characteristics of the antenna under different
conditions. The measured return loss and radiation pattern indicate
the suitability of this design for WLAN applications, namely, Wi-
Max, 802.11a/b/g and ISM bands.
Abstract: New Growth Theory helps us make sense of the
ongoing shift from a resource-based economy to a knowledge-based
economy. It underscores the point that the economic processes which
create and diffuse new knowledge are critical to shaping the growth
of nations, communities and individual firms. In all too many
contributions to New (Endogenous) Growth Theory – though not in
all – central reference is made to 'a stock of knowledge', a 'stock of
ideas', etc., this variable featuring centre-stage in the analysis. Yet it
is immediately apparent that this is far from being a crystal clear
concept. The difficulty and uncertainty of being able to capture the
value associated with knowledge is a real problem. The intent of this
paper is introducing new thinking and theorizing about the
knowledge and its measurability in new growth theory. Moreover the
study aims to synthesize various strain of the literature with a
practical bearing on knowledge concept. By contribution of
institution framework which is found within NGT, we can indirectly
measure the knowledge concept. Institutions matter because they
shape the environment for production and employment of new
knowledge
Abstract: In this paper, in order to categorize ORL database face
pictures, principle Component Analysis (PCA) and Kernel Principal
Component Analysis (KPCA) methods by using Elman neural
network and Support Vector Machine (SVM) categorization methods
are used. Elman network as a recurrent neural network is proposed
for modeling storage systems and also it is used for reviewing the
effect of using PCA numbers on system categorization precision rate
and database pictures categorization time. Categorization stages are
conducted with various components numbers and the obtained results
of both Elman neural network categorization and support vector
machine are compared. In optimum manner 97.41% recognition
accuracy is obtained.
Abstract: The demand on High voltage (HV) infrastructures is growing due to the corresponding growth in industries and population. Many areas are being developed and therefore require additional electrical power to comply with the demand. Substation upgrade is one of the rapid solutions to ensure the continuous supply of power to customers. This upgrade requires civil modifications to structures and fences. The civil work requires excavation and steel works that may create unsafe touch conditions. This paper presents a brief theoretical overview of the touch voltage inside and around substations and uses CDEGS software to simulate a case study.
Abstract: This paper presents ageing experiments controlled by the evolution of junction parameters. The deterioration of the device is related to high injection effects which modified the transport mechanisms in the space charge region of the junction. Physical phenomena linked to the degradation of junction parameters that affect the devices reliability are reported and discussed. We have used the method based on numerical analysis of experimental current-voltage characteristic of the junction, in order to extract the electrical parameters. The simultaneous follow-up of the evolutions of the series resistance and of the transition voltage allow us to introduce a new parameter for reliability evaluation.
Abstract: The paper considers the effect of feed plate location
on the interactions in a seven plate binary distillation column. The
mathematical model of the distillation column is deduced based on
the equations of mass and energy balances for each stage, detailed
model for both reboiler and condenser, and heat transfer equations.
The Dynamic Relative Magnitude Criterion, DRMC is used to assess
the interactions in different feed plate locations for a seven plate
(Benzene-Toluene) binary distillation column ( the feed plate is
originally at stage 4). The results show that whenever we go far from
the optimum feed plate position, the level of interaction augments.
Abstract: The use of amine mixtures employing
methyldiethanolamine (MDEA), monoethanolamine (MEA), and diethanolamine (DEA) have been investigated for a variety of cases
using a process simulation program called HYSYS. The results show that, at high pressures, amine mixtures have little or no advantage in the cases studied. As the pressure is lowered, it becomes more difficult for MDEA to meet residual gas requirements and mixtures can usually improve plant performance. Since the CO2 reaction rate
with the primary and secondary amines is much faster than with
MDEA, the addition of small amounts of primary or secondary amines to an MDEA based solution should greatly improve the overall reaction rate of CO2 with the amine solution. The addition of MEA caused the CO2 to be absorbed more strongly in the upper portion of the column than for MDEA along. On the other hand,
raising the concentration for MEA to 11%wt, CO2 is almost
completely absorbed in the lower portion of the column. The addition of MEA would be most advantageous.
Thus, in areas where MDEA cannot meet the residual gas
requirements, the use of amine mixtures can usually improve the plant
performance.
Abstract: In present article the model of Blended Learning, its advantage at foreign language teaching, and also some problems that can arise during its use are considered. The Blended Learning is a special organization of learning, which allows to combine classroom work and modern technologies in electronic distance teaching environment. Nowadays a lot of European educational institutions and companies use such technology. Through this method: student gets the opportunity to learn in a group (classroom) with a teacher and additionally at home at a convenient time; student himself sets the optimal speed and intensity of the learning process; this method helps student to discipline himself and learn to work independently.
Abstract: In this paper we investigate the electrical
characteristics of a new structure of gate all around strained silicon
nanowire field effect transistors (FETs) with dual dielectrics by
changing the radius (RSiGe) of silicon-germanium (SiGe) wire and
gate dielectric. Indeed the effect of high-κ dielectric on Field Induced
Barrier Lowering (FIBL) has been studied. Due to the higher electron
mobility in tensile strained silicon, the n-type FETs with strained
silicon channel have better drain current compare with the pure Si
one. In this structure gate dielectric divided in two parts, we have
used high-κ dielectric near the source and low-κ dielectric near the
drain to reduce the short channel effects. By this structure short
channel effects such as FIBL will be reduced indeed by increasing
the RSiGe, ID-VD characteristics will be improved. The leakage
current and transfer characteristics, the threshold-voltage (Vt), the
drain induced barrier height lowering (DIBL), are estimated with
respect to, gate bias (VG), RSiGe and different gate dielectrics. For
short channel effects, such as DIBL, gate all around strained silicon
nanowire FET have similar characteristics with the pure Si one while
dual dielectrics can improve short channel effects in this structure.
Abstract: In this paper an algorithm is used to detect the color defects of ceramic tiles. First the image of a normal tile is clustered using GCMA; Genetic C-means Clustering Algorithm; those results in best cluster centers. C-means is a common clustering algorithm which optimizes an objective function, based on a measure between data points and the cluster centers in the data space. Here the objective function describes the mean square error. After finding the best centers, each pixel of the image is assigned to the cluster with closest cluster center. Then, the maximum errors of clusters are computed. For each cluster, max error is the maximum distance between its center and all the pixels which belong to it. After computing errors all the pixels of defected tile image are clustered based on the centers obtained from normal tile image in previous stage. Pixels which their distance from their cluster center is more than the maximum error of that cluster are considered as defected pixels.
Abstract: An important step in studying the statistics of
fingerprint minutia features is to reliably extract minutia features from
the fingerprint images. A new reliable method of computation for
minutiae feature extraction from fingerprint images is presented. A
fingerprint image is treated as a textured image. An orientation flow
field of the ridges is computed for the fingerprint image. To
accurately locate ridges, a new ridge orientation based computation
method is proposed. After ridge segmentation a new method of
computation is proposed for smoothing the ridges. The ridge skeleton
image is obtained and then smoothed using morphological operators
to detect the features. A post processing stage eliminates a large
number of false features from the detected set of minutiae features.
The detected features are observed to be reliable and accurate.
Abstract: In this paper, parallelism in the solution of Ordinary
Differential Equations (ODEs) to increase the computational speed is
studied. The focus is the development of parallel algorithm of the two
point Block Backward Differentiation Formulas (PBBDF) that can
take advantage of the parallel architecture in computer technology.
Parallelism is obtained by using Message Passing Interface (MPI).
Numerical results are given to validate the efficiency of the PBBDF
implementation as compared to the sequential implementation.
Abstract: Grid networks provide the ability to perform higher throughput computing by taking advantage of many networked computer-s resources to solve large-scale computation problems. As the popularity of the Grid networks has increased, there is a need to efficiently distribute the load among the resources accessible on the network. In this paper, we present a stochastic network system that gives a distributed load-balancing scheme by generating almost regular networks. This network system is self-organized and depends only on local information for load distribution and resource discovery. The in-degree of each node is refers to its free resources, and job assignment and resource discovery processes required for load balancing is accomplished by using fitted random sampling. Simulation results show that the generated network system provides an effective, scalable, and reliable load-balancing scheme for the distributed resources accessible on Grid networks.
Abstract: The purpose of this paper isunavailability of the two main types of conveSwedish traction power supply (TPS) system, i.e.static converter. The number of outages and the ouused to analyze and compare the unavailability oconverters. The mean cumulative function (MCF)analyze the number of outages and the unavailabthe forced outage rate (FOR) concept has been uoutage rates. The study shows that the outagesfailure occur at a constant rate by calendar timconverter stations, while very few stations havedecreasing rate. It has also been found that the stata higher number of outages and a higher outage ratcompared to the rotary converter types. The resultsthat combining the number of outages and the fgives a better view of the converters performasupport for the maintenance decision. In fact, usingdoes not reflect reality. Comparing these two indein identifying the areas where extra resources are maintenance planning and where improvementsoutage in the TPS system.KeywordsFrequency Converter, Forced OuCumulative Function, Traction Power Supply, ESystems.
Abstract: We present a new method for the fully automatic 3D
reconstruction of the coronary artery centerlines, using two X-ray
angiogram projection images from a single rotating monoplane
acquisition system. During the first stage, the input images are
smoothed using curve evolution techniques. Next, a simple yet
efficient multiscale method, based on the information of the Hessian
matrix, for the enhancement of the vascular structure is introduced.
Hysteresis thresholding using different image quantiles, is used to
threshold the arteries. This stage is followed by a thinning procedure
to extract the centerlines. The resulting skeleton image is then pruned
using morphological and pattern recognition techniques to remove
non-vessel like structures. Finally, edge-based stereo correspondence
is solved using a parallel evolutionary optimization method based on
f symbiosis. The detected 2D centerlines combined with disparity
map information allow the reconstruction of the 3D vessel
centerlines. The proposed method has been evaluated on patient data
sets for evaluation purposes.