Abstract: This research was carried out to determine the
possible effects of low electromagnetic field (EMF) exposure to the
developing mice fetuses. Pregnant mice were exposed to EMF
exposure at 0mT (sham) and 1.2 mT for six hours per session, carried
out on gestation day 3, 6, 9, 12 and 15. Samples from the stillborn
offspring were observed for morphological defects. The heart didn-t
show progressive cellular damage, the lungs were congested and
emphysemics. The bones were in advance stage of hypertrophy.
Spectrums of morphological defects were observed over 70% of the
surviving offspring. These results indicate that even at lower
exposure to low EMF, is enough to induce morphological defects in
prenatal mice.
Abstract: A lateral trench-gate power metal-oxide-semiconductor on 4H-SiC is proposed. The device consists of two separate trenches in which two gates are placed on both sides of P-body region resulting two parallel channels. Enhanced current conduction and reduced-surface-field effect in the structure provide substantial improvement in the device performance. Using two dimensional simulations, the performance of proposed device is evaluated and compare of with that of the conventional device for same cell pitch. It is demonstrated that the proposed structure provides two times higher output current, 11% decrease in threshold voltage, 70% improvement in transconductance, 70% reduction in specific ON-resistance, 52% increase in breakdown voltage, and nearly eight time improvement in figure-of-merit over the conventional device.
Abstract: The paper presents the potential of fuzzy logic (FL-I)
and neural network techniques (ANN-I) for predicting the
compressive strength, for SCC mixtures. Six input parameters that is
contents of cement, sand, coarse aggregate, fly ash, superplasticizer
percentage and water-to-binder ratio and an output parameter i.e. 28-
day compressive strength for ANN-I and FL-I are used for modeling.
The fuzzy logic model showed better performance than neural
network model.
Abstract: Estimation of voltage stability based on optimal
filtering method is presented. PV curve is used as a tool for voltage stability analysis. Dynamic voltage stability estimation is done by
using particle filter method. Optimum value (nose point) of PV curve can be estimated by estimating parameter of PV curve equation
optimal value represents critical voltage and
condition at specified point of measurement. Voltage stability is then estimated by analyzing loading margin condition c stimating equation. This
maximum loading
ecified dynamically.
Abstract: In this study, effects of premixed and equivalence
ratios on CO and HC emissions of a dual fuel HCCI engine are
investigated. Tests were conducted on a single-cylinder engine with
compression ratio of 17.5. Premixed gasoline is provided by a
carburetor connected to intake manifold and equipped with a screw
to adjust premixed air-fuel ratio, and diesel fuel is injected directly
into the cylinder through an injector at pressure of 250 bars. A heater
placed at inlet manifold is used to control the intake charge
temperature. Optimal intake charge temperature results in better
HCCI combustion due to formation of a homogeneous mixture,
therefore, all tests were carried out over the optimum intake
temperature of 110-115 ºC. Timing of diesel fuel injection has a great
effect on stratification of in-cylinder charge and plays an important
role in HCCI combustion phasing. Experiments indicated 35 BTDC
as the optimum injection timing. Varying the coolant temperature in
a range of 40 to 70 ºC, better HCCI combustion was achieved at 50
ºC. Therefore, coolant temperature was maintained 50 ºC during all
tests. Simultaneous investigation of effective parameters on HCCI
combustion was conducted to determine optimum parameters
resulting in fast transition to HCCI combustion. One of the
advantages of the method studied in this study is feasibility of easy
and fast transition of typical diesel engine to a dual fuel HCCI
engine. Results show that increasing premixed ratio, while keeping
EGR rate constant, increases unburned hydrocarbon (UHC)
emissions due to quenching phenomena and trapping of premixed
fuel in crevices, but CO emission decreases due to increase in CO to
CO2 reactions.
Abstract: Since the 80s huge efforts have been made to utilize
renewable energy sources to generate electric power. This paper
reports some aspects of integration of the distributed generators into
the low voltage distribution networks. An assessment of impact of the
distributed generators on the reliability indices of low voltage
network is performed. Results obtained from case study using low
voltage network, are presented and discussed.
Abstract: A diamond-like carbon (DLC) based solid-lubricant
film was designed and DLC films were successfully prepared using a
microwave plasma enhanced magnetron sputtering deposition
technology. Post-test characterizations including Raman
spectrometry, X-ray diffraction, nano-indentation test, adhesion test,
friction coefficient test were performed to study the influence of
substrate bias voltage on the mechanical properties of the W- and
S-doped DLC films. The results indicated that the W- and S-doped
DLC films also had the typical structure of DLC films and a better
mechanical performance achieved by the application of a substrate
bias of -200V.
Abstract: In first stage of each microwave receiver there is Low
Noise Amplifier (LNA) circuit, and this stage has important rule in
quality factor of the receiver. The design of a LNA in Radio
Frequency (RF) circuit requires the trade-off many importance
characteristics such as gain, Noise Figure (NF), stability, power
consumption and complexity. This situation Forces desingners to
make choices in the desing of RF circuits. In this paper the aim is to
design and simulate a single stage LNA circuit with high gain and
low noise using MESFET for frequency range of 5 GHz to 6 GHz.
The desing simulation process is down using Advance Design
System (ADS). A single stage LNA has successfully designed with
15.83 dB forward gain and 1.26 dB noise figure in frequency of 5.3
GHz. Also the designed LNA should be working stably In a
frequency range of 5 GHz to 6 GHz.
Abstract: In this paper, we present an analytical analysis of the
representation of images as the magnitudes of their transform with
the discrete wavelets. Such a representation plays as a model for
complex cells in the early stage of visual processing and of high
technical usefulness for image understanding, because it makes the
representation insensitive to small local shifts. We found that if the
signals are band limited and of zero mean, then reconstruction from
the magnitudes is unique up to the sign for almost all signals. We
also present an iterative reconstruction algorithm which yields very
good reconstruction up to the sign minor numerical errors in the very
low frequencies.
Abstract: Fluorescent and WOLED are widely used because it consumes less energy. However, both lamps cause a harmonics because it has semiconductors components. Harmonic is a distorted sinusoidal electric wave and cause excess heat. This study compares the amount of harmonics generated by both lamps. The test shows that both lamps have THDv(Total Harmonics Distortion of Voltage) almost the same with average 2.5% while the average of WOLED's THDi(Total Harmonics Distortion of Current) is lower than fluorescent has. The average WOLED's THDi is 29.10 % and fluorescent's 'THDi is 87. 23 %.
Abstract: Integration of process planning and scheduling
functions is necessary to achieve superior overall system
performance. This paper proposes a methodology for integration of
process planning and scheduling for prismatic component that can be
implemented in a company with existing departments. The developed
model considers technological constraints whereas available time for
machining in shop floor is the limiting factor to produce multiple
process plan (MPP). It takes advantage of MPP while guarantied the
fulfillment of the due dates via using overtime. This study has been
proposed to determinate machining parameters, tools, machine and
amount of over time within the minimum cost objective while
overtime is considered for this. At last the illustration shows that the
system performance is improved by as measured by cost and
compatible with due date.
Abstract: Knowledge Discovery of Databases (KDD) is the
process of extracting previously unknown but useful and significant
information from large massive volume of databases. Data Mining is
a stage in the entire process of KDD which applies an algorithm to
extract interesting patterns. Usually, such algorithms generate huge
volume of patterns. These patterns have to be evaluated by using
interestingness measures to reflect the user requirements.
Interestingness is defined in different ways, (i) Objective measures
(ii) Subjective measures. Objective measures such as support and
confidence extract meaningful patterns based on the structure of the
patterns, while subjective measures such as unexpectedness and
novelty reflect the user perspective. In this report, we try to brief the
more widely spread and successful subjective measures and propose
a new subjective measure of interestingness, i.e. shocking.
Abstract: A major challenge in camel productivity is the high
mortality rate of camel calves in the early stage due to the lack of
colostrums. This study investigates the time required for the calves to
obtain the optimum amount of the immunoglobulin (IgG). Eleven
pregnant female camels (Camelus Dromedarus) were selected
randomly and variant in age and gestation. After delivery, 7 calves
were obtained and used for this investigation. Colostrum samples
were collected from mothers immediately after parturition. Blood
samples were obtained from the calves as follow: 0 day (before
suckling), 24, 48, 72, 96, 120 and 144 hours, 2nd, 3rd, and 4th weeks
post suckling. Blood serum and colostrums whey were separated and
used to determine IgG concentration, total protein and concentration
of Cortisol and Thyroxin. The results showed high levels of IgG in
camel colostrums (328.8 ± 4.5 mg / ml). The IgG concentration in
serum of calves was the highest within 1st 24 h after suckling (140.75
mg /ml), and then declined gradually reached lower level at 144 h
(41.97 mg / ml). The average turnover rate (t 1/2) of serum IgG in
the all cases was 3.22 days. The turnover of ranged from 2.56 days
for calves have values of IgG more than average and 7.7 days for
those with values below average. In spite of very high levels of
thyroxin in sera of new born the results showed no correlation
between cortisol and thyroxin with IgG levels.
Abstract: Self-Excited Induction Generator (SEIG) builds up voltage while it enters in its magnetic saturation region. Due to non-linear magnetic characteristics, the performance analysis of SEIG involves cumbersome mathematical computations. The dependence of air-gap voltage on saturated magnetizing reactance can only be established at rated frequency by conducting a laboratory test commonly known as synchronous run test. But, there is no laboratory method to determine saturated magnetizing reactance and air-gap voltage of SEIG at varying speed, terminal capacitance and other loading conditions. For overall analysis of SEIG, prior information of magnetizing reactance, generated frequency and air-gap voltage is essentially required. Thus, analytical methods are the only alternative to determine these variables. Non-existence of direct mathematical relationship of these variables for different terminal conditions has forced the researchers to evolve new computational techniques. Artificial Neural Networks (ANNs) are very useful for solution of such complex problems, as they do not require any a priori information about the system. In this paper, an attempt is made to use cascaded neural networks to first determine the generated frequency and magnetizing reactance with varying terminal conditions and then air-gap voltage of SEIG. The results obtained from the ANN model are used to evaluate the overall performance of SEIG and are found to be in good agreement with experimental results. Hence, it is concluded that analysis of SEIG can be carried out effectively using ANNs.
Abstract: Piezoelectric transformers are electronic devices made
from piezoelectric materials. The piezoelectric transformers as the
name implied are used for changing voltage signals from one level to another. Electrical energy carried with signals is transferred by means of mechanical vibration. Characterizing in both electrical and
mechanical properties leads to extensively use and efficiency enhancement of piezoelectric transformers in various applications. In
this paper, study and analysis of electrical and mechanical properties of multi-layer piezoelectric transformers in forms of potential and
displacement distribution throughout the volume, respectively. This
paper proposes a set of quasi-static mathematical model of electromechanical
coupling for piezoelectric transformer by using a set of
partial differential equations. Computer-based simulation utilizing the three-dimensional finite element method (3-D FEM) is exploited
as a tool for visualizing potentials and displacements distribution
within the multi-layer piezoelectric transformer. This simulation was
conducted by varying a number of layers. In this paper 3, 5 and 7 of
the circular ring type were used. The computer simulation based on
the use of the FEM has been developed in MATLAB programming environment.
Abstract: This research paper evaluates and compares the
performance of equal cost adaptive multi-path routing algorithms
taking the transport protocols TCP (Transmission Control Protocol)
and UDP (User Datagram Protocol) using network simulator ns2 and
concludes which one is better.
Abstract: The main objective of this paper is to determine the
isolated effect of silica fume on tensile, compressive and flexure strengths on high strength lightweight concrete. Many experiments
were carried out by replacing cement with different percentages of silica fume at different constant water-binder ratio keeping other mix
design variables constant. The silica fume was replaced by 0%, 5%,
10%, 15%, 20% and 25% for a water-binder ratios ranging from 0.26
to 0.42. For all mixes, split tensile, compressive and flexure strengths
were determined at 28 days. The results showed that the tensile, compressive and flexure strengths increased with silica fume incorporation but the optimum replacement percentage is not
constant because it depends on the water–cementitious material (w/cm) ratio of the mix. Based on the results, a relationship between
split tensile, compressive and flexure strengths of silica fume concrete was developed using statistical methods.
Abstract: Medical imaging uses the advantage of digital
technology in imaging and teleradiology. In teleradiology systems
large amount of data is acquired, stored and transmitted. A major
technology that may help to solve the problems associated with the
massive data storage and data transfer capacity is data compression
and decompression. There are many methods of image compression
available. They are classified as lossless and lossy compression
methods. In lossy compression method the decompressed image
contains some distortion. Fractal image compression (FIC) is a lossy
compression method. In fractal image compression an image is
coded as a set of contractive transformations in a complete metric
space. The set of contractive transformations is guaranteed to
produce an approximation to the original image. In this paper FIC is
achieved by PIFS using quadtree partitioning. PIFS is applied on
different images like , Ultrasound, CT Scan, Angiogram, X-ray,
Mammograms. In each modality approximately twenty images are
considered and the average values of compression ratio and PSNR
values are arrived. In this method of fractal encoding, the
parameter, tolerance factor Tmax, is varied from 1 to 10, keeping the
other standard parameters constant. For all modalities of images the
compression ratio and Peak Signal to Noise Ratio (PSNR) are
computed and studied. The quality of the decompressed image is
arrived by PSNR values. From the results it is observed that the
compression ratio increases with the tolerance factor and
mammogram has the highest compression ratio. The quality of the
image is not degraded upto an optimum value of tolerance factor,
Tmax, equal to 8, because of the properties of fractal compression.
Abstract: Drying characteristics of rough rice (variety of lenjan) with an initial moisture content of 25% dry basis (db) was studied in a hot air dryer assisted by infrared heating. Three arrival air temperatures (30, 40 and 500C) and four infrared radiation intensities (0, 0.2 , 0.4 and 0.6 W/cm2) and three arrival air speeds (0.1, 0.15 and 0.2 m.s-1) were studied. Bending strength of brown rice kernel, percentage of cracked kernels and time of drying were measured and evaluated. The results showed that increasing the drying arrival air temperature and radiation intensity of infrared resulted decrease in drying time. High bending strength and low percentage of cracked kernel was obtained when paddy was dried by hot air assisted infrared dryer. Between this factors and their interactive effect were a significant difference (p
Abstract: Web intelligence, if made personal, can fuel the process of building communications around the interests and preferences of each individual customer or prospect, by providing specific behavioral insights about each individual. To become fully efficient, Web intelligence must reach a stage of a high-level maturity, passing throughout a process that involves five steps: (1) Web site analysis; (2) Web site and advertising optimization; (3) Segment targeting; (4) Interactive marketing (online only); and (5) Interactive marketing (online and offline). Discussing these steps in detail, the paper uncovers the real gold mine that is personal-level Web intelligence.