Abstract: It has experimentally been proved that the
performance of compression ignition (C.I.) engine is spray
characteristics related. In modern diesel engine the spray formation
and the eventual combustion process are the vital processes that offer
more challenges towards enhancing the engine performance. In the
present work the numerical simulation has been carried out for
evaporating diesel sprays using Fluent software. For computational
fluid dynamics simulation “Meshing” is done using Gambit software
before transmitting it into Fluent. The simulation is carried out using
hot bomb conditions under varying chamber conditions such as gas
pressure, nozzle diameter and fuel injection pressure. For comparison
purpose, the numerical simulations the chamber conditions were kept
the same as that of the experimental data. At varying chamber
conditions the spray penetration rates are compared with the existing
experimental results.
Abstract: The spring-driven ball-type check valve is one of the
most important components of hydraulic systems: it controls the
position of the ball and prevents backward flow. To simplify the
structure, the spring must be eliminated, and to accomplish this, the
flow pattern and the behavior of the check ball in L-shaped pipe must
be determined. In this paper, we present a full-scale model of a check
ball made of acrylic resin, and we determine the relationship between
the initial position of the ball, the position and diameter of the inflow
port. The check flow rate increases in a standard center inflow model,
and it is possible to greatly decrease the check-flow rate by shifting the
inflow from the center.
Abstract: At certain depths during large diameter displacement
pile driving, rebound well over 0.25 inches was experienced,
followed by a small permanent-set during each hammer blow. High
pile rebound (HPR) soils may stop the pile driving and results in a
limited pile capacity. In some cases, rebound leads to pile damage,
delaying the construction project, and the requiring foundations
redesign. HPR was evaluated at seven Florida sites, during driving of
square precast, prestressed concrete piles driven into saturated, fine
silty to clayey sands and sandy clays. Pile Driving Analyzer (PDA)
deflection versus time data recorded during installation, was used to
develop correlations between cone penetrometer (CPT) pore-water
pressures, pile displacements and rebound. At five sites where piles
experienced excessive HPR with minimal set, the pore pressure
yielded very high positive values of greater than 20 tsf. However, at
the site where the pile rebounded, followed by an acceptable
permanent-set, the measured pore pressure ranged between 5 and 20
tsf. The pore pressure exhibited values of less than 5 tsf at the site
where no rebound was noticed. In summary, direct correlations
between CPTu pore pressure and rebound were produced, allowing
identification of soils that produce HPR.
Abstract: In order to better understand the long term
implications of the grout wear failure mode in large-diameter plainsided
grouted connections, a numerical model has been developed
and calibrated that can take advantage of existing operational plant
data to predict the wear accumulation for the actual load conditions
experienced over a given period, thus limiting the requirement for
expensive monitoring systems. This model has been derived and
calibrated based on site structural condition monitoring (SCM) data
and supervisory control and data acquisition systems (SCADA) data
for two operational wind turbine generator substructures afflicted
with this challenge, along with experimentally derived wear rates.
Abstract: Rotary draw bending is a method which is being used
in tube forming. In the tube bending process, the neutral axis moves
towards the inner arc and the wall thickness distribution changes for
tube’s cross section. Thinning takes place in the outer arc of the tube
(extrados) due to the stretching of the material, whereas thickening
occurs in the inner arc of the tube (intrados) due to the comparison of
the material. The calculations of the wall thickness distribution,
neutral axis shifting, and strain distribution have not been accurate
enough, so far. The previous model (the geometrical model)
describes the neutral axis shifting and wall thickness distribution. The
geometrical of the tube, bending radius and bending angle are
considered in the geometrical model, while the influence of the
material properties of the tube forming are ignored. The advanced
model is a modification of the previous model using material
properties that depends on the correction factor. The correction factor
is a purely empirically determined factor. The advanced model was
compared with the Finite element simulation (FE simulation) using a
different bending factor (Bf =bending radius/ diameter of the tube),
wall thickness (Wf = diameter of the tube/ wall thickness), and
material properties (strain hardening exponent). Finite element model
of rotary draw bending has been performed in PAM-TUBE program
(version: 2012). Results from the advanced model resemble the FE
simulation and the experimental test.
Abstract: In order to manufacture short gap single Si nanowire
(NW) field effect transistor (FET) by imprinting and transferring
method, we introduce the method using Al2O3 sacrificial layer. The
diameters of cylindrical Si NW addressed between Au electrodes by
dielectrophoretic (DEP) alignment method are controlled to 106, 128,
and 148 nm. After imprinting and transfer process, cylindrical Si NW
is embedded in PVP adhesive and dielectric layer. By curing
transferred cylindrical Si NW and Au electrodes on PVP-coated p++ Si
substrate with 200nm-thick SiO2, 3μm gap Si NW FET fabrication
was completed. As the diameter of embedded Si NW increases, the
mobility of FET increases from 80.51 to 121.24 cm2/V·s and the
threshold voltage moves from –7.17 to –2.44 V because the ratio of
surface to volume gets reduced.
Abstract: Geopolymer concretes are new class of construction
materials that have emerged as an alternative to Ordinary Portland
cement concrete. Considerable researches have been carried out on
material development of geopolymer concrete; however, a few studies
have been reported on the structural use of them. This paper presents
the bond behaviors of reinforcement embedded in fly ash based
geopolymer concrete. The development lengths of reinforcement for
various compressive strengths of concrete, 20, 30 and 40 MPa, and
reinforcement diameters, 10, 16 and 25 mm, are investigated. Total 27
specimens were manufactured and pull-out test according to EN 10080
was applied to measure bond strength and slips between concrete and
reinforcements. The average bond strengths decreased from 23.06MPa
to 17.26 MPa, as the diameters of reinforcements increased from
10mm to 25mm. The compressive strength levels of geopolymer
concrete showed no significant influence on bond strengths in this
study. Also, the bond-slip relations between geopolymer concrete and
reinforcement are derived using non-linear regression analysis for
various experimental conditions.
Abstract: In this research, waterglass based aerogel powder was
prepared by sol–gel process and ambient pressure drying. Inspired by
limited dust releasing, aerogel powder was introduced to the PET
electrospinning solution in an attempt to create required bulk and
surface structure for the nanofibers to improve their hydrophobic and
insulation properties. The samples evaluation was carried out by
measuring density, porosity, contact angle, heat transfer, FTIR, BET,
and SEM. According to the results, porous silica aerogel powder was
fabricated with mean pore diameter of 24 nm and contact angle of
145.9º. The results indicated the usefulness of the aerogel powder
confined into nanofibers to control surface roughness for
manipulating superhydrophobic nanowebs with water contact angle
of 147º. It can be due to a multi-scale surface roughness which was
created by nanowebs structure itself and nanofibers surface
irregularity in presence of the aerogels while a layer of fluorocarbon
created low surface energy. The wettability of a solid substrate is an
important property that is controlled by both the chemical
composition and geometry of the surface. Also, a decreasing trend in
the heat transfer was observed from 22% for the nanofibers without
any aerogel powder to 8% for the nanofibers with 4% aerogel
powder. The development of thermal insulating materials has become
increasingly more important than ever in view of the fossil energy
depletion and global warming that call for more demanding energysaving
practices.
Abstract: In sheet metal forming process, raw material
mechanical properties are important parameters. This paper is to
compare the wall’s incline angle or formability of SS 400 steel and
SUS 304 stainless steel in single point incremental forming. The two
materials are ferrous base alloyed, which have the different unit cell,
mechanical property and chemical composition. They were forming
into cone shape specimens having 100 mm diameter with different
wall’s incline angle: 90o, 75o and 60o. The investigation was
continued until the specimens formed surface facture. The
experimental result showed that the smaller the wall incline angle
higher the formability with the both materials. The formability limit
of the ferrous base alloy was approx. 60o wall’s incline angle. By
nature, SS 400 has higher formability than SUS 304. This result can
be used as the initial data in designing the single point incremental
forming parts.
Abstract: Yttrium oxide (Y2O3) films have been successfully
deposited with yttrium-ethylenediamine tetraacetic acid (EDTA·Y·H)
complexes prepared by various milling techniques. The effects of the
properties of the EDTA·Y·H complex on the properties of the
deposited Y2O3 films have been analyzed. Seven different types of the
raw EDTA·Y·H complexes were prepared by various commercial
milling techniques such as ball milling, hammer milling, commercial
milling, and mortar milling. The milled EDTA·Y·H complexes
exhibited various particle sizes and distributions, depending on the
milling method. Furthermore, we analyzed the crystal structure,
morphology and elemental distribution profile of the metal oxide films
deposited on stainless steel substrate with the milled EDTA·Y·H
complexes. Depending on the milling technique, the flow properties of
the raw powders differed. The X-ray diffraction pattern of all the
samples revealed the formation of Y2O3 crystalline phase, irrespective
of the milling technique. Of all the different milling techniques, the
hammer milling technique is considered suitable for fabricating dense
Y2O3 films.
Abstract: Violet Sr–Al–O:Eu2+ phosphor particles were
synthesized from a metal–ethylenediaminetetraacetic acid (EDTA)
solution of Sr, Al, Eu, and particulate alumina via spray drying and
sintering in a reducing atmosphere. The crystal structures and emission
properties at 85–300 K were investigated. The composition of the
violet Sr–Al–O:Eu2+ phosphor particles was determined from various
Sr–Al–O:Eu2+ phosphors by their emission properties’ dependence
on temperature. The highly crystalline SrAl12O19:Eu2+ emission phases
were confirmed by their crystallite sizes and the activation energies for
the 4f5d–8S7/2 transition of the Eu2+ ion. These results showed that the
material identification for the violet Sr–Al–O:Eu2+ phosphor was
accomplished by the low-temperature luminescence measurements.
Abstract: Laser beam welding for the dissimilar Titanium and
Aluminium thin sheets is an emerging area which is having wider
applications in aerospace, aircraft, automotive, electronics and in
other industries due to its high speed, non-contact, precision with low
heat effects, least welding distortion, low labor costs and convenient
operation. Laser beam welding of dissimilar metal combinations are
increasingly demanded due to high energy densities with small fusion
and heat affected zones. Furthermore, no filler or electrode material is
required and contamination of weld is also very small. The present
study is to reviews the influence of different parameters like laser
power, welding speed, power density, beam diameter, focusing
distance and type of shielding gas on the mechanical properties of
dissimilar metal combinations like SS/Al, Cu/Al and Ti/Al focusing
on aluminum to other materials. Research findings reveal that Ti/Al
combination gives better metallurgical and mechanical properties
than other combinations such as SS/Al and Cu/Al.
Abstract: The hydrogenated amorphous carbon films (α-C:H)
were deposited on p-type Si (100) substrates at different thicknesses by
radio frequency plasma enhanced chemical vapor deposition
technique (rf-PECVD). Raman spectra display asymmetric
diamond-like carbon (DLC) peaks, representative of the α-C:H films.
The decrease of intensity ID/IG ratios revealed the sp3 content arise at
different thicknesses of the α-C:H films. In terms of mechanical
properties, the high hardness and elastic modulus values showed the
elastic and plastic deformation behaviors related to sp3 content in
amorphous carbon films. Electrochemical properties showed that the
α-C:H films exhibited excellent corrosion resistance in air-saturated
3.5 wt.% NaCl solution for pH 2 at room temperature. Thickness
increasing affected the small sp2 clusters in matrix, restricting the
velocity transfer and exchange of electrons. The deposited α-C:H films
exhibited excellent mechanical properties and corrosion resistance.
Abstract: This paper evaluates the performance of a multi-lane
four legged modern roundabout operating in Muscat using SIDRA
model. The performance measures include Degree of Saturation
(DOS), average delay, and queue lengths. The geometric and traffic
data were used for model preparation. Gap acceptance parameters,
critical gap and follow up headway, were used for calibration of
SIDRA model. The results from the analysis showed that currently
the roundabout is experiencing delays up to 610 seconds per vehicle
with DOS 1.67 during peak hour. Further, sensitivity analysis for
general and roundabout parameters was performed, amongst lane
width, cruise speed, inscribed diameter, entry radius and entry angle
showed that inscribed diameter is most crucial factor affecting delay
and DOS. Up gradation of roundabout to fully signalized junction
was found as the suitable solution which will serve for future years
with LOS C for design year having DOS of 0.9 with average control
delay of 51.9 seconds per vehicle.
Abstract: Multiwall carbon nanotubes, prepared by chemical
vapor deposition, have an average diameter of 60-100 nm as shown
by High Resolution Transmittance Electron Microscope, HR-TEM.
The Multiwall carbon nanotubes (MWCNTs) were further
characterized using X-ray Diffraction and Raman Spectroscopy.
Mercury uptake capacity of MWCNTs was studied using batch
adsorption method at different concentration ranges up to 150 ppm.
Mercury concentration (before and after the treatment) was measured
using cold vapor atomic absorption spectroscopy. The effect of time,
concentration, pH and adsorbent dose were studied. MWCNT were
found to perform complete absorption in the sub-ppm concentrations
(parts per billion levels) while for high concentrations, the adsorption
efficiency was 92% at the optimum conditions; 0.1 g of the adsorbent
at 150 ppm mercury (II) solution. The adsorption of mercury on
MWCNTs was found to follow the Freundlich adsorption isotherm
and the pseudo-second order kinetic model.
Abstract: The study was conducted to evaluate the efficiency of
Garlic and Chili combination solution on control of insect pests in
cabbage crop. The solution was sprayed at different intervals after
transplanting. The efficiency of Garlic and chili combination solution
on cabbage insect pests was measured. Results revealed that Garlic
and chili combination solution was the effectively reduced cabbage
insect pests. On other hand, the spray solution not only reduced the
number of days required for the cabbage growth but also greatly
enhanced the leaf number, head diameter, head weight, and quality of
cabbage. Garlic and chili combination solution have positive effects
on pests reduction and improve growth, yield and quality of cabbage
vegetable.
Abstract: A wireless sensor network (WSN) is a collection of
sensor nodes organized into a cooperative network. These nodes
communicate through a wireless antenna. Reduction in physical size
and multiband operation is an important requirement of WSN
antenna. Fractal antenna is used for miniaturization and multiband
operation. The self-similar or self-affine and space filling property of
fractal geometry increases the effective electrical length of the
antenna, reduces the size and make them frequency independent. This
paper elaborates on Dual band fractal antenna with Coplanar
Waveguide (CPW) feed for WSN. The proposed antenna is designed
on a FR4 substrate with the dimension of 27mm x 28.5mm x 1.6mm,
resonates at 2.4GHz and 5.2GHz with a return loss less than -10dB.
The design and simulation process is carried out using IE3D
simulation software. The simulated and measured results are found in
good agreement.
Abstract: Theoretical optimization of a copper-water negative
inclination heat pipe with internal composite wick structure had been
performed, regarding a new introduced parameter: the ratio between
the coarse mesh wraps and the fine mesh wraps of the composite
wick. Since in many cases, the design of a heat pipe matches specific
thermal requirements and physical limitations, this work
demonstrates the optimization of a 1m length, 8mm internal diameter
heat pipe without an adiabatic section, at a negative inclination angle
of -10º. The optimization is based on a new introduced parameter, LR:
the ratio between the coarse mesh wraps and the fine mesh wraps.
Abstract: Metal-enhanced Luminescence of silicon nanocrystals
(SiNCs) was determined using two different particle sizes of silver
nanoparticles (AgNPs). SiNCs have been characterized by scanning
electron microscopy (SEM), high resolution transmission electron
microscopy (HRTEM), Fourier transform infrared spectroscopy
(FTIR) and X-ray photoelectron spectroscopy (XPS). It is found that
the SiNCs are crystalline with an average diameter of 65 nm and FCC
lattice. AgNPs were synthesized using photochemical reduction of
AgNO3 with sodium dodecyl sulphate (SDS). The enhanced
luminescence of SiNCs by AgNPs was evaluated by confocal Raman
microspectroscopy. Enhancement up to x9 and x3 times were
observed for SiNCs that mixed with AgNPs which have an average
particle size of 100 nm and 30 nm, respectively. Silver NPs-enhanced
luminescence of SiNCs occurs as a result of the coupling between the
excitation laser light and the plasmon bands of AgNPs; thus this
intense field at AgNPs surface couples strongly to SiNCs.