Abstract: Captured images may suffer from Gaussian blur due to poor lens focus or camera motion. Unsharp masking is a simple and effective technique to boost the image contrast and to improve digital images suffering from Gaussian blur. The technique is based on sharpening object edges by appending the scaled high-frequency components of the image to the original. The quality of the enhanced image is highly dependent on the characteristics of both the high-frequency components and the scaling/gain factor. Since the quality of an image may not be the same throughout, we propose an adaptive unsharp masking method in this paper. In this method, the gain factor is computed, considering the gradient variations, for individual pixels of the image. Subjective and objective image quality assessments are used to compare the performance of the proposed method both with the classic and the recently developed unsharp masking methods. The experimental results show that the proposed method has a better performance in comparison to the other existing methods.
Abstract: Rotary draw bending is a method which is being used
in tube forming. In the tube bending process, the neutral axis moves
towards the inner arc and the wall thickness distribution changes for
tube’s cross section. Thinning takes place in the outer arc of the tube
(extrados) due to the stretching of the material, whereas thickening
occurs in the inner arc of the tube (intrados) due to the comparison of
the material. The calculations of the wall thickness distribution,
neutral axis shifting, and strain distribution have not been accurate
enough, so far. The previous model (the geometrical model)
describes the neutral axis shifting and wall thickness distribution. The
geometrical of the tube, bending radius and bending angle are
considered in the geometrical model, while the influence of the
material properties of the tube forming are ignored. The advanced
model is a modification of the previous model using material
properties that depends on the correction factor. The correction factor
is a purely empirically determined factor. The advanced model was
compared with the Finite element simulation (FE simulation) using a
different bending factor (Bf =bending radius/ diameter of the tube),
wall thickness (Wf = diameter of the tube/ wall thickness), and
material properties (strain hardening exponent). Finite element model
of rotary draw bending has been performed in PAM-TUBE program
(version: 2012). Results from the advanced model resemble the FE
simulation and the experimental test.
Abstract: This work presents a study on the abrasive water jet
(AWJ) machining. An explicit finite element analysis (FEA) of
single abrasive particle impact on stainless steel 1.4304 (AISI 304) is
conducted. The abrasive water jet machining is modeled by FEA
software ABAQUS/CAE. Shapes of craters in FEM simulation
results were used and compared with the previous experimental and
FEM works by means of crater sphericity. The influence of impact
angle and particle velocity was observed. Adaptive mesh domain is
used to model the impact zone. Results are in good agreement with
those obtained from the experimental and FEM simulation. The
crater-s depth is also obtained for different impact angle and abrasive
particle velocities.
Abstract: The aim of this study was to demonstrate the possible
effect of some variables such as age, gender, blood sugar level, and
duration of diabetes on the serum level of zinc in diabetic individuals
from Murzuk area. Serum zinc (Zn), Fasting blood sugar (FBS),
hemoglobin HbA1c (HbA1c) were evaluated in 46 type I diabetic
subjects (group 1), 48 type II diabetic subjects (group 2) and 43
healthy individuals (control) of both genders aged (30-81) years. Data
showed that both diabetic groups have significantly higher (P0.05) differences in serum Zn levels were observed
between Males and Females. Serum Zn levels were non-significantly
decreased with increasing age. In type II diabetic subjects, serum Zn
levels were non-significantly decreased with increasing duration of
disease whereas those in type I were non-significantly increased.
Abstract: E-government projects have potential for greater efficiency and effectiveness of government operations. For this reason, many developing countries governments have invested heavily in this agenda and an increasing number of e-government projects are being implemented. However, there is a lack of clear case material, which describes the potentialities and consequence experienced by organizations trying to manage with this change. The Ministry of State for Administrative Development (MSAD) is the organization responsible for the e-Government program in Egypt since early 2004. This paper presents a case study of the process of admission to public universities and institutions in Egypt which is led by MSAD. Underlining the key benefits resulting from the initiative, explaining the strategies and the development steps used to implement it, and highlighting the main obstacles encountered and how they were overcome will help repeat the experience in other useful e-government projects.